Search Documents

At the exploration stage for new mining projects or for medium- and long-term areas of existing mines (typical of South African gold mines), drilling data is on a relatively large grid. This grid is normally larger than the selective mining units (SMUs). Direct estimates for the SMUs and also of much larger block units will then be smoothed due to the information effect and the high error variance. Any capital-intensive project decisions made on the basis of any of the smoothed estimates will tend to misrepresent the economic value of the project or operation, i.e. the average grade of blocks above cut-off will be underestimated and the tonnage overestimated for cut-off grades below the mean grade of the orebody. This paper presents a direct approach technique for deriving recoverable resources, referred to as localized direct conditioning (LDC), designed to correct smoothing effects and also to provide support corrections.

Jan 1, 2014

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

By E. V. Lilford

A number of countries have introduced codes governing the valuation of mineral assets and securities. The African continent will follow suit in due course considering the importance of the global minerals industry as it relates to the attraction of foreign investment. South Africa is to introduce the Petroleum and Minerals Development Bill legislating the involvement of previously disadvantaged individuals and communities in the country?s minerals industry. One of the challenges facing the successful implementation of such codes and bills lies with the abilities of independent valuators to value mineral properties and projects on a consistent basis. Certain valuation principles and methodologies are applicable in all jurisdictions in the minerals industry. These valuation tools and principles are considered and developed in this report. They have been discussed and developed to encourage minerals valuators to consider and consistently apply the most applicable valuation methodologies.

Jan 1, 2002

By D. F. Malan

This study reviews the concept of squeezing (large time-dependent deformation) in rock and investigates the possibility of this phenomenon becoming more pronounced in the planned ultra-deep mines of the South African gold mining industry. Although squeezing behaviour is not commonly found at the current depths of the gold mining industry, it is observed at Hartebeestfontein Mine due to a combination of weak rock and high stresses. Calculations based on the average strength of the Witwatersrand quartzites and the competency factor used to identify squeezing conditions in civil engineering tunnels, indicate that there is an increased risk of squeezing behaviour in ultra-deep mines. This will adversely affect the profitability of these mines and highlights the need for further research into the time-dependent behaviour of rock. Finally, the current support strategies in squeezing conditions are reviewed.

Jan 1, 1998

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By N. Simpson

Low carbon 11.5% chromium stainless steels are finding increasing use in industry as square or rectangular tubing material for the construction of structures by welding. During processing, resistively welded circular pipes are bent into square or rectangular shapes. During this process longitudinal cracks can sometimes develop atone of the inner corners of the section. An investigation has shown that the processing of round into square tubing with very sharp corners can cause excessive cold working at the inner corners of the squared tube. This, together with the high tensile residual stresses and a susceptible microstructure due to the presence of grain boundary carbides, can result in brittle cleavage cracking. Measures that can be used to reduce the problem are described.

Jan 1, 2003

By G. V. R. Landman

In the early days of underground coal mining, the use of explosives to break coal resulted in a large number of disastrous methane and coal dust explosions and consequential loss of life. Research by the British, French, US authorities, amongst others, introduced many practices that significantly reduced the occurrence of such incidences. The use of explosives designed to be safe in a methane atmosphere, plus the creation of a second free face were two such practices which became commonly used in coal mines all over the world including southern Africa. With its associated coal cutting equipment and labour, the cost of creating a second free face is significant and this, together with the constant drive to reduce mining costs in a competitive market, causes mine management to regularly question the need for the second free face. Also, the safety and nature of permitted explosives has changed considerably since the days of black powder and nitroglycerine-based explosives with the introduction of water-based explosives. In southern Africa mining regulations pertaining to the blasting of coal has its origins in British research which was largely done in the first half of the twentieth century. More recent research by the US Bureau of Mine has resulted in a deeper understanding of some of the mechanisms of methane ignition by explosives and suggests that some of the earlier regulations can be relaxed to a certain extent without compromising safety. This paper gives an overview of the original research done in Europe and the more recent work in the USA, to give mine management and regulatory authorities a deeper understanding of the important safety issues when using explosives in a methane atmosphere. It also suggests that blasting off the solid is no less safe than using a second free face providing certain safety procedures are followed.

Jan 1, 2000

By G. Swan, E. Nordlund, P. Zhang

"SynopsisThe most widely used support design damage criterion for rockburst-prone mines is based upon kinetic energy, which is proportional to the square of the ejection velocity and is commonly expressed in terms of peak particle velocity (PPV). Field monitoring and back-analyses have shown that ejection velocities of the order of 10 m/s and higher can result from seismic events of moderate magnitude. Such velocities are much higher than those predicted using PPV obtained from scaling laws. It has also been found that the peak ground motion (i.e. PPV) on the surface of an excavation is preferentially amplified (by four- to tenfold) compared to the motion in solid rock at a similar distance from the source. However, the wave propagation and interaction processes involved within the fractured rock in generating high ground motion are very complex and are not well understood at this time.In this paper, velocity amplification was investigated by modelling the dynamic interaction between fractured rock and a free surface using a 2D discontinuum-based numerical program, UDEC (Universal Distinct Element Code). A 1D model with a fractured zone was used to represent the fractured rock. Velocity amplification, quantified by PPV, predicted at the free end of the model was 2.0–3.6 times higher than the input velocity. It was found that the wave frequency, fracture stiffness, fracture spacing, and thickness of fractured zone are the main factors that affect the velocity amplification. The results have proved that the interaction of the seismic wave and multiple fractures near the free surface strongly influences the ground motion.IntroductionSince mining-induced seismicity is almost inevitable in deep mines, ground support is generally employed to mitigate the risk of seismically-induced damage. The most widely used support design criterion for seismicallyprone mines is one that seeks to maximize the absorption of the kinetic energy (plus potential energy if a gravity component is considered) of key rock blocks. Based on this criterion, design methods for rock support were first proposed by Wagner (1984) in South Africa and later improved, among others, by Roberts and Brummer (1988) and Kaiser et al. (1996)."

Jan 1, 2015

By R. Ribacchi, P. Tommasi, C. Consorti, P. Campedel

The runout of dry blocky rock avalanches produced by planar rockslides affecting a limestone formation with clayey interbeds is analysed by means of distinct element modelling. Numerical analyses are validated by means of the back analysis of a historical rockslide occurred in the investigated area and physical aspects of the phenomenon evidenced by modelling are discussed. On analyse par la méthode aux élements distincts la distance de parcours des avalanches rocheuses sèches produites par des glissements plan interessant une formation de calcaire à intercalaires argilleux. Les analyses numeriques sont validées à l’aide de la back-analysis d’un glissement historique survenue dans le site en examen. On décrit les aspects physiques su phénomène mis en évidence par la modélisation efféctuée. In diesem Beitrag wird die Reichweite von Steinlawinen besthend aus trockenem blockhaftem Fels mittels der Distinct Element Methode untersucht. Die Steinlawinen werden erzeugt von Rutschungen in einer Kalkstein-Formation mit tonhaltige Schichten betreffen. Die numerischen Berechnungen wurden anhand einer Simulation einer historischen Bergsturzen verifiziert, der sich auf den untersuchten Gebiet ereignete. Auf der Basis der erhaltenen Ergebnisse wurden die physikalischen Aspekte der untersuchten Steinlawinen analysiert.

Jan 1, 2003

By C. J. Badenhorst

The scope of this project was to research, develop and eventually produce a personal occupational hygiene and safety exposure monitor system to assist in recording and analysing various stress factors that could affect the health, wellness and safety of employees, i.e. that could result in injury or ill health of workers, create stress build-up within individual workers that could negatively affect worker alertness and safety, and, may even result in permanent disability or death. Utilized systems at the time were all reactive, whereas the DOHEMS (Proactive Digital Occupational Hygiene and Safety Exposure Monitoring) System enabled the measurement of exposure (and associated risk) in a proactive manner via real-time exposure and digitized recordings. The idea of the development was to create a unit that is so cost effective, small and light that every worker can use a system on a daily basis. The development will eventually replace current, bulky and expensive monitoring equipment. The device must be a portable battery operated device and monitor the immediate working environment by periodic sampling for vibration, noise, toxic gasses (NO/NOX/CO/VOC, etc.), body temperature and heart rate. The samples must be time and date stamped, utilizing a real-time clock (RTC) synchronized with the closest regional secondary time source and related to synchronized real-time video captured samples. These samples are then recorded onto a rugged non volatile storage device with the capacity to store a vast number of samples covering the entire working shift of eight (8) hours plus. The system has been fitted with a clear visual local alarm indication system, indicating any excessive exposures or stresses, for the worker?s supervisor to respond to. This system allows for a pro-active approach. The system is also a wireless system (to the external environment) so as to not affect the mobility of an employee and flameproof to allow for use in explosive environments. Keywords: safety, digital, exposure, monitoring, proactive.

Jan 1, 2010

By S. O?Connor

When one looks back and does assessments of what has been the key ingredient in achieving success in our safety efforts, there are many issues that spring to mind and cover a wide array of elements. One does not know which has the ultimate maximum effect. In his presentation yesterday, Alan Peers, our SHEQ leader, covered a lot of detail with the way we are managing safety at Modikwa. I have attempted to identify some of the key essentials in making the mine safe. Passion Safety is addressed with a passion that is unbelievable at times. When I get phoned because an incident has occurred and in reporting the incident, there are already action plans being put in place to prevent re-occurrences, you understand the commitment to put employees? safety first. You hear the disappointment in your subordinates? voices when they have to share the fact that an incident or accident has occurred.

Jan 1, 2011

By L. A. Thompson, A. J. Linington

"Copper–cobalt extraction is a reagent-intensive process resulting in acid consumption greatly contributing towards production costs, which in the current market conditions curtail profitability. Nanofiltration (NF) membranes have become an attractive approach in the mining and minerals industry for product concentration and reagent recovery based on the ability of the membrane to separate monovalent ions from divalent ions. NF membranes can selectively separate acids from metals and salts allowing acid to be recycled as well as the concentration and purification of product streams. Membrane technology in the field of copper–cobalt processing focusses on the concentration of Cu2+ and Co2+ in the pregnant leach solution, recovery of acid from waste streams to neutralization, recovery of valuable metals from waste ponds and process water recovery. This paper aims to provide insight into the potential applications of NF membranes in copper–cobalt processing circuits as well as a brief overview of the effects of process conditions on membrane performance and process development. INTRODUCTION The copper–cobalt industry commonly uses inorganic acids, such as sulfuric acid, in large quantities for primary leaching of copper–cobalt oxide ores and releaching during product purification (Stuurman et al., 2014). This results in numerous acidic intermediate streams containing high metal concentrations and acidic waste streams with low metal concentrations. Acid consumption typically accounts for 10–15% of the operating costs of mines in the Democratic Republic of Congo (DRC) and Zambia (Acid Plant Database, 2015). Due to remote mine locations, poorly maintained roads and cross-border conflict, the cost of sulphuric acid can range between USD 300 and 400 per ton. The pivotal role of acid in the copper–cobalt extraction process has driven many mines to build sulphuric acid plants on site to ensure a reliable acid supply, however elemental sulphur still needs to be imported which faces similar logistical challenges and contributes towards operating costs."

Jan 1, 2015

By W. Barnett

The Limpopo Metamorphic Belt is a complex geological terrane with at least three major deformational events. Tectonically juxtaposed lithology, open to isoclinal folding, crosscutting and re-activated shear zones and metamorphic gneisses and schists make pit slope design and maintenance a risky business. Venetia diamond mine?s Cut 3 is planned to reach 360 m by 2011. The difficult rockmass created problems in the original pit and a new more comprehensive slope design was necessary. Nearly 9 km of geotechnical drilling were undertaken to produce a new geological model and provide geotechnical information near the final Cut 3 face. All existing data from the pit were brought together into a database. SRK Consulting were brought into the project to audit the process and provide most of the manpower for the data analysis. Existing failures were back-analysed and the geotechnical domains identified. Analyses of only the southern domains are discussed in this paper. Geotechnical engineers can design slopes at any angle, but it is up to the managers at the mine to decide what risk they are willing to accept in a slope design. Once the issue of risk was discussed and settled in respect of the consequences of failure, each of the main geotechnical domains were analysed to produce a slope design at5% probability of failure with 15% above the first ramp. A risk assessment of the design was then undertaken to determine what risk the design placed on the equipment, personnel and the profitability of the overall mining operation. The risk assessment indicated minimal risk to the operation. One of the main assumptions of the final design is that the pit slopes will be dewatered. A project was immediately put in place to determine a groundwater model for the mine and to thereby determine the best dewatering procedure. However, it should be obvious that it is practically impossible to prevent benches from getting briefly saturated with water during storm conditions. It was therefore necessary to look specifically at supporting the crests of the ramps in the problematic southern domains to guard against the possibility of crest failure during heavy rains. The data available were re-analysed toward this objective. Spiles were recommended as the most cost-effective support system, and a probabilistic approach was used in the design. The final design has a 5% probability of failure, and the analyses indicate a strong sensitivity of the required spile spacing to the strength of the reinforcement material that will eventually be used. The pit slope parameters derived as per the discussion in this paper have just begun to be implemented at Venetia Mine.

Jan 1, 2001

By R. Abela

Heavy mineral sands are usually beneficiated in a spiral concentrator circuit prior to separation of heavy minerals into streams of zircon, rutile and ilmenite. The performance of the spiral concentrators is heavily affected by the presence of slimes in the rougher feed. The paper quantifies the effect of slimes content and discusses the beneficial effect of spiral feed de-sliming. The net effect of inefficient slimes removal can cause significant recovery losses of the heavy minerals present in the feed.

Jan 1, 2003

By M. van Schoor

Coal remains South Africa?s most abundant and cheapest source of energy, and there is an ever-increasing necessity for optimal and safe extraction of the remaining reserves. Increasing focus on cost-effective mining and zero harm to the environment and miners has resulted in a shift in attitude towards the application of geophysics in local coal mining and exploration. Furthermore, technological advances have contributed to geophysics being embraced more readily by the coal mining industry, compared to a decade or two ago. Predictably, the growing interest in geophysical technologies has also created a need for education and training in the basic principles and application of geophysical methods, as local coal mining companies generally do not have in-house geophysicists. Consequently, the Coaltech Research Organisation?s Geology and Geophysics working group forum compiled a textbook aimed at addressing this need: to produce a guide for applying geophysics to coal mining problems in South Africa. The target audience for such a book would be coal geologists, mine surveyors, mine planners, and other mining staff with limited or no geophysics background. This paper provides a very brief overview of the book by summarizing key sections and selected examples. In doing so, the value of geophysics to solving a range of coal mining and exploration problems is highlighted.

Jan 1, 2014

By M. A. van Nierop

Load behaviour in an industrial mill has been measured directly by inserting probes through liner bolts. The data from conductivity probes have indicated the presence of premature centrifuging during manipulation of the load mass. Overloading conditions were also encountered. Overloading and premature centrifuging both reduce the power drawn by the mill. These effects have been successfully modelled.

Jan 1, 1997

By G. M. Cresswell

The 2 360 t/h two module Phola coal preparation plant represents anew era of large plant in the Witbank coalfield designed to extend its life to 2020 and beyond. The plant uses the optimum processing model for Witbank coals, receiving a feed coal size of -50 mm, wet screening it into coarse and small coal fractions 50 x12 and 12 x0.63 mm before processing them in parallel through two primary DM cyclone sections, in order to make a 27.5 MJ/kg export floats product. The sinks are processed through a common high density DM cyclone section to produce a 21.5?23 MJ/kg thermal coal middlings product. The plant design incorporates the largest size DMS equipment used to date in South African coal preparation plants, i.e. 1 150 mm large diameter pump fed DM cyclones and 4.2 m width banana screens. The fine coal is conventionally processed by spirals, whereas the raw coal slimes are filtered using automated plate and frame filter presses and added to either the middlings or discards depending on its quality. The paper describes the database, innovative design concepts, construction, and commissioning.

Jan 1, 2010

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that contains between 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By R. A. Williams

Electrical impedance tomographic methods have been applied to a variety of mineral and chemical processes in the laboratory and on plant. This review paper surveys technical developments in measurement methods to enable quantitative extraction of key process information in the form of mapping of concentration profiles, mixture homogeneity and suspension velocity. The methods for determining velocity are summarized, since this is of especial interest when applied to opaque systems where most conventional optically based measurements fail. A recent significant development is the use of ultra-high speed measurement that now allows velocity vectors to be extracted for fast moving mixtures and fluids (up to several metres per second). New data are reported pertinent to low and high solids concentration flow in pipelines. Use of the methods offer improvements to design of such systems but also points to the use of tomographic electrical sensor as online flow measurement and fault detection. This offers new opportunities for applications and benefits in the design and monitoring of mineral slurries and sludges.

Jan 1, 2008