Search Documents

By J. H. Cloete, S. M. Bradshaw, D. K. Chibwe

"Modern tundishes have evolved as vessels to serve as the final step in refining of molten steel by removing inclusions and promoting thermochemical homogeneity.In this study the flow behaviour in a four-strand tundish was investigated by means of a ½-scale water model as well as numerical modelling. The numerical and physical models were used to characterize residence time distribution and calculate properties pertaining to tundish flow regime. Three different tundish configurations were investigated: a bare tundish with no flow control devices, a tundish with a turbulence inhibitor, and a tundish with both a turbulence inhibitor and a dam.The physical and numerical models showed that a tundish without flow control devices is prone to significant short-circuiting. A tundish with a turbulence inhibitor was shown to be successful in preventing shortcircuiting and provided surface-directed flow that might assist the removal of inclusions from the melt. However, it was also observed that the upward-directed flow caused the maximum turbulence kinetic energy near the surface to increase dramatically. The potential for slag entrainment should therefore be considered during the design and operation of tundishes with turbulence inhibitors."

Jan 1, 2015

The aim of this investigation was to study the influence that varying production rates have on iron sinter quality. This was done by performing sinter pot tests at different pressure drops over the sinter bed, namely 11 kPa and 15 kPa (for 500 mm total bed depths). During each of the sintering processes temperature-time profiles were recorded of the top, middle and bottom layers of the sinter bed. On completion of the sinter process the sinter cakes were divided into top, middle and bottom layers. The physical properties of each layer were subsequently characterized by performing a tumbler test and a sieve analysis. A comprehensive mineralogical study was also conducted on each layer. This study revealed that sinters of similar cold strength could be produced under the examined production rates. However, a higher production rate was accompanied by an increased amount of fines. The cold strengths of both sinters significantly increased from the top layer to the bottom layer of the sinter bed. This strength variation is not related in any simple way to the phase composition. Keywords: Sinter, sinter bed, production rate, phase composition, cold strength, tumbler index, sieve analysis, temperature-time profile

Jan 1, 2003

By D. Chetty

The characterization of platinum group minerals (PGMs) from concentrator flotation circuits provides valuable information towards understanding PGM recovery under given milling and flotation conditions. Additional mineralogical characterization also provides information on ore variability, which may affect recovery. Considering the low grades involved, automated scanning electron microscopy (SEM) characterization of PGMs has enabled relatively quick analyses, compared with older, time consuming and less accurate optical microscopy methods. Over the years, parameters, such as species, size distribution, liberation, gangue and base metal sulfide (BMS) associations, have been used to characterize the PGMs in a process mineralogical context, to aid metallurgical interpretation. This paper considers whether flotation indices determined for PGMs can be empirically validated, using initial results from analysis of PGMs in a concentrate bank from a South African concentrator treating UG2 ore from the western limb of the Bushveld Complex. The aim is to determine whether floatability is adequately described by these parameters, or whether other mineralogical factors must be considered when assessing PGM floatability, and hence accounting for recovery vs. losses to tails. The data obtained to date, show that flotation parameters (including liberation index, BMS/gangue relationships and size distribution) have merits where large changes in PGM concentration occur, as observed in the first four cells of the concentrate bank. Larger data sets, however, are required to assess floatability, particularly where concentrate cell grades are similar, as observed in the last six cells of the concentrate bank. Furthermore, the floatability indices could be enhanced by the incorporation of selected associated gangue mineral information, chief amongst these being the content and mode of occurrence of naturally floatable talc and associated orthopyroxene.

Jan 1, 2009

By L. D. van Dyk

The extraction of iron and lead from their oxides with a volatile organic ligand such as acetylacetone in the gas phase offers potential advantages of lower energy consumption, recycling of the extractant, recovery of pure metals, and a reduced environmental impact compared with conventional extraction processes. The influence of reaction temperature, ligand flow rate, and metal oxide levels on the extraction and rates of reaction of iron and lead from single metal oxide (synthetic haematite (Fe2O3) and synthetic massicot (PbO)) systems in a fluidized bed was studied. It was found that at the investigated acetylacetone flow rates, the influence of mass transfer was limited, but that the reaction suffered from reactant starvation. When the metal load increased the effect of starvation on the rate of reaction also increased. The reaction kinetics increased with an increase in temperature for both systems. At low metal oxide concentrations more that 80 per cent of the iron and lead could be extracted from their respective metal oxides after only four hours.

Jan 1, 2012

A reliable laboratory method to characterize the response of free gold particles to flash flotation conditions has been developed. The test has been performed on free milling gold ores as well as synthetic ores, using either a gravity concentrate or gold powder as the gold source, to assess the floatability of gold particles. Trends in free gold flotation kinetics, as well as size and milling effects, were identified for gold recovery based on the different feed types, reagent dosages, and residence times. It was shown that the ultimate recoveries and kinetic trends of gold particles from the gravity concentrate could be enhanced with increased dosage of collector, potassium amyl xanthate. Interestingly, in comparison to gravity-recoverable gold, recovery from pure Au powders was better in collectorless flotation, and cumulative recovery decreased with higher levels of collector addition. Improved coarse particle recovery appeared linked to increased collector additions for both the gravity concentrate and the pure gold powders. In general, coarse gold particles demonstrated slower kinetic rates thaen the fine or intermediate components incomparable tests.

Jan 1, 2015

By C J. de Beer

The Kwaggashoek East pit is one of the four production areas of Thabazimbi Iron Ore Mine. The Kwaggashoek East Open pit mines through the abandoned sublevel caving operations of the Kwaggashoek East underground workings. A risk assessment indicated that the primary risk is the occurrence of surface subsidence. Based on local knowledge, a hypothesis, that most of the cavities were filled with broken rock as a result of roof collapse and bulking of failed material was formulated. To test the hypothesis a number of geophysical methods as well as probe drilling was utilized. The results of the resistivity, gravity and ground penetrating radar surveys were inconclusive in determining the position of voids. Either there were no voids present or the resolution of the surveys was not high enough to pick it up. It is accepted that only small voids remained, and that the supported roof hypothesis is valid. As a precautionary measure all the production blast holes within the caving area were over-drilled by forty percent. This would collapse the roof of any small voids or tunnels immediately below the block. This operation proved to be successful as two of the three underground levels have been mined out with no subsidence occurring in the pit floor.

Jan 1, 2006

By J. D. Stone

This paper briefly reviews the adequacy of existing management theories and practices and the managerial proficiency or competency in the South African mining industry. The investigation revealed that existing management practices are totally inadequate to enable all employees on all the levels of the mining industry to achieve the results required from them, in all aspects, at all times. As a result, the South African mining industry is gradually losing its long standing reputation as a relative cheap, competitive, and reliable supplier of minerals to the local and global markets. According to some prominent management authors and theorists, an all-inclusive unified management theory does not exist at present. In this paper the authors summarize the main aspects of a newly developed comprehensive, practical, and integrated management method. It is believed that the application of this method would significantly improve the future performance and competitiveness of the South African mining industry

Jan 1, 2010

By F. T. Cawood

This article is a continuation of a series of publications by the authors on the international debate on resource nationalism, with specific reference to South Africa. Previous outcomes have shown that mine nationalization is not a solution for South Africa, and that maintaining stability of the current mineral and tax regimes is fundamental. It will not be wise to replace existing law and policy instruments until there is a better understanding of the distinction between fact and public perception about the impact of the current system. The new scheme of state custodianship linked to a mining royalty that effectively targets economic rents provides for effective resource use. The methodology in this article is to consider how South Africa's mineral tax regime can be tweaked to achieve optimal management and benefit from mineral extraction and associated rents by avoiding changes feared by investors. The major finding is that the current suite of instruments can be considered a suitable platform for optimal management of resource rents. However, it will be necessary to first investigate ways of improving the mineral beneficiation intent of the royalty structure, and secondly investigate whether the mineral rent portion of the royalty formula can be ring-fenced for the purpose of establishing a sovereign wealth fund.

Jan 1, 2013

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By Chris D. Winkler

Vanadium-based sulphuric acid catalyst has been utilized to oxidize SO2 to SO3 since the early 1900?s. This versatile product displaced the expensive and easily-poisoned platinum-based catalyst in nearly all applications by the 1930?s. MECS has been manufacturing the vanadium-based catalyst since 1925 and today is the leading supplier in the world of sulphuric acid catalysts in a variety of forms. Currently, MECS has world-wide customer/technical support for the catalyst as well as a dedicated catalyst manufacturing plant in Martinez, California. MECS also has a strong technical and research and development program dedicated to creating new and improved products and services. This paper will describe some of the technical details of vanadium-based sulphuric acid catalysts as well as offering a unique look into how caesium-promoted MECS catalysts can be used in single and double absorption acid plants, and off-gas plants running on irregular gas feeds, to reduce emissions and pre-heater run times. An update on MECS technical services extended for use in characterizing converter performance is also presented.

Jan 1, 2009

By J. Kortnik

Mining has always been, and still is, an activity which is vital for the development of mankind. This is because a predominant proportion of industrial products and energy is produced from raw materials that are excavated using mining methods. The need for environmental protection and the close proximity of urban settlements and mines in Slovenia have necessitated ever stricter requirements for the excavation of raw materials and introduction of more environmentally-friendly mining methods. This is achieved by implementing a closed eco-technological cycle of raw material excavation within the scope of mining methods. In surface mines, this means prompt reclamation of the degraded surfaces, and in underground mines the use of methods with minimized impact on the surface and on underground water. In underground mines, mining methods with backfilling installed according to the multi-barrier disposal system are the only ones that allow the possibility of implementing a closed eco-technological cycle of excavating raw materials. Various industrial waste materials are also included in the backfilling material in order to improve its strength properties. Backfilling consisting of several different waste materials is produced in the form of a composite. Before backfilling consisting of waste material composites can even begin to be used in mines, an environmental impact assessment of its suitability for mines needs to be made. In order to make such an assessment, a pressure leaching cell and an open diffusion cell were made, i.e. a pressure leachate test and a sorption test were developed. The two cells and the developed tests will enable the study of the influence of backfilling on the environment if installed in an underground mine. The pressure leachate test performed with the use of the pressure leaching cell simulates leaching from a consolidated backfill during the seeping of underground water into the backfilling material under pressure. The sorption test performed in an open diffusion cell simulates the flow of eluate leached from the backfilling material through the rock/geotechnical barrier. The two tests were developed in such a manner that they are performed either in succession immediately after one another, but they can also be performed separately at a certain time interval. The paper presents an assessment of the suitability of backfilling made of different waste material composites. Keywords: environmental impact assessment, multi-barrier disposal system, waste material composites, pressure leachate test, sorption test, pressure leaching cell, open diffusion cell, eco-technological cycle, mining methods with backfilling.

Jan 1, 2003

Sishen Iron Ore Mine previously used only A-grade material (>60% Fe in situ value) from the pit for beneficiating in the DMS plant to a final product grade of 66% Fe in lump and 65% Fe fine ore. The B-grade (between 50% and 60% Fe) and C-grade material (between 35% and 50% Fe) were stockpiled separately, owing to the inability of the existing DMS plant to beneficiate material at densities higher than 3600 kg/m3. The ability to beneficiate the B-grade material at densities higher than 3600 kg/m3 was evaluated, and air-pulsed jigs were found to be techno-economically feasible and value maximizing. The beneficiation of B-grade material would add to the existing DMS production of 28 Mt/a, with no additional mining cost and only limited costs for the handling of waste and B-material. The objective of the Sishen Expansion Project (SEP), i.e. the jig plant, was to produce 10 Mt/a of saleable product with six modules to the set physical and chemical specifications by 2009. During the start of construction, it was decided to add another two jig modules to the plant to increase production to 13 Mt/a. During commissioning and ramp-up the shortcomings and advantages of the jigs were fully experienced and understood, resulting in many changes to optimize jigging performance..

Jan 1, 2014

By M. Pineda

Sublevel stoping (SLS) is one of the oldest and most used methods for underground mining. It relies heavily on the use of drilling and blasting techniques to remove the rock, and gravity to transport the broken rock to drawpoints located at the base of the stope, with LHDs to transport material from the drawpoints. Current SLS operations are based on the assumption of stable geometry of the stope. Thus, the stope design includes the definition of the geometry according to the orebody shape and geomechanical constraints to avoid instability, which may cause excessive dilution. Under some circumstances, dilution could enter the stope due to geotechnical instability, especially when large stope geometries are used. A review of current design and planning practices for large SLS operations indicates that no consideration is given to the material flow and the mixing that occurs after blasting. Material flow could have a large impacton the mixing of ore when grades are heterogeneous in the stope. In this paper, we discuss the influence of gravity flow on the design and planning of large sublevel stopes with and without vertical dilution, based on laboratory experiments. The outcomes of this investigation are used todevelop guidelines towards the design and planning of large SLS mines, which would complement the currently used geotechnical considerations.

Jan 1, 2015

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By C. -J. Rick

By implementing a converter downstream of the reduction furnace it is possible to broaden the product range significantly. The converter can also successfully be used to strip furnace slag from chromium oxide. Some process alternatives and their economical, practical and environmental implications are studied using process models developed based on UHT?s long experience in stainless steelmaking, stainless steel process control and charge chrome refining. Keywords Charge chrome, converter refining, ferrochromium products, process design.

Jan 1, 2010

By M. McWha

Laboratory bias is a universal problem in all branches of analytical science. It results from differences in methods, techniques, equipment, and calibrations between laboratories. Notwithstanding that it is a property that can be measured by the use of standards or by inter-laboratory testing, laboratory bias remains a material issue for the mining industry. There is extensive literature and clear guidelines on measurement from the International Organization for Standardization (ISO) and its worldwide federation of national standards bodies (ISO member bodies) and from the science of metrology. ISO guides cover the manufacture and use of standards. An accessible source of literature covering laboratory quality control comes from the public health sector, particularly pathology. There is little doubt in financial reporting rules about the meaning of materiality. Public reporting guidelines are clear that material matters need to be disclosed for investors. Unfortunately there is currently no clear guidance what to do about biased assay results in mineral industry public reporting guidelines. This paper reviews the requirements for the manufacture and use of reference materials, public reporting requirements in the mining industry, and presents proposals to improve management and reporting of laboratory biases. Keywords laboratory bias, reference materials, ISO Guides, financial reporting, materiality.

Jan 1, 2014

By A. A. Angelov

This paper presents a unique method of monitoring the effectiveness of the planning process as well as the execution of mine plans. The method primarily determines the degree of deviation from the original mine plans by comparing actual mined areas to initially planned mining areas. The performance of mining operations is also measured by comparing actual and planned tonnages for a particular period. Once the degree of deviation from mine plans has been established the cause/s of the deviation can be determined through a simple fault tree analysis. Accurate identification of the reasons of deviation can aid the mine in selecting possible methods to correct the deviation. It is, however, beyond the scope of this paper to discuss the methods employed in correcting such deviations, as each mining operation will have unique causes of plan deviation and methods of remedying them. Deviations from the plan greatly affect the yields obtainable, which in turn affects the life of mine, thus having negative economic and financial implications. Accordingly, this paper presents a project management method which aims to reduce risk by improving planning systems to ensure optimum overall extraction of coal reserves.

Jan 1, 2010

By J. He

The separation performance of a raw coal sample from South Africa based on the dense gas-solid fluidized bed beneficiation technique was investigated. Analysis showed that the raw coal sample distributes mainly in the -50+6 mm size range with the -1.6 g/cm3 density fraction accounting for 78.20% of the cumulative mass distribution. A flow sheet of the sequential coal beneficiation technique was introduced. The experimental and simulation results of the hydromechanical and density distribution stability indicate that the dense gas-solid fluidized bed could provide a stable separation environment with uniform density fluctuations under suitable operating conditions. With the application of this technique on the raw coal sample, the separation results show that three products, consisting of 73.25% clean coal with an ash content of 9.59%, 11.31% middlings, and 15.44% gangue were effectively separated at two different densities of 1.82 g/cm3 and 1.57 g/cm3. This study provides an effective flow sheet for achieving the high-efficiency separation performance on raw coal from arid areas. Keywords dense gas-solid fluidized bed, dry coal beneficiation, density distribution, separation efficiency.

Jul 1, 2013

By X. Q. Cao, D. S. Zhang, L. Q. Ma

To solve the support stability control problem for a coal face with large angles along both strike and dip (CLSD), the ’support-surrounding rock’ mechanical model has been developed, which takes into account the impact of the dip angle of the seam on the stability of the support in the strike direction. The mechanical relationships of the critical topple angle and critical slip angle of the support along the strike of the coal face with large dip angle and the support height, support resistance, friction coefficient, and other factors have been derived through the mechanical analysis of support stability in the strike direction of CLSDs in the free state, the operating state, and the special state. The research findings were applied to a fully mechanized CLSD in Xinji Coal Mine. The maximum underhand angle and overhand angle in strike are 42° and 25° respectively, and the maximum dip is 39°. It is calculated that during underhand mining and overhand mining, the critical support resistances for avoiding support toppling are 3723 kN and 1714 kN respectively, and the critical support resistances for avoiding slipping of the support are 7405 kN and 6606 kN respectively. Thus, the selection of type ZZ7600/18/38 hydraulic roof support for the coal face is justified. Measures to prevent sliding of the support and the installation of a limiting stop maintain the support runs in good condition and ensure safe and efficient mining of CLSD.

Jan 1, 2015