Search Documents

By A. Koursaris, Y. Turan

The object of this study was to investigate the i1Jfluence of nitrogen on the structure and properties of AISI 310S steel. Experimental ingots of the steel with nitrogen contents of up to 0,525 per cent by weight were prepared, hot-rolled, and tested after various treatments. The rollability of the material was adequate. The yield strength, tensile strength, hardness, and fatigue properties of the new alloys improved with increasing nitrogen content. The impact properties improved slightly. Empirical equations were developed for the calculation of the yield and tensile strengths, as well as the difference between these two properties, with increasing nitrogen content.

Jan 1, 1995

By Gordon Chunnett, Ron Sheets, David Grant

[Power-Point Presentation]

Jan 1, 2005

By A. Singh, R. R. Maclachlan

SYNOPSIS A back-analysis procedure based upon 35 mm photography was developed on a laboratory scale for the pur¬pose of determining the percentage of oversize particles known to be present in heaps of fragmented rock. Eight simple blends of crushed stone containing varying percentages of oversize on a 1:40 modelled scale were examined. Simulated test conditions for the following were subjected to the photographic study: (1) a bench heap, (2) the surface exposure of a partially excavated heap, (3) a gravity-sorted surface as occurs on an apron dump, and (4) four quadrant views of an incrementally built conical heap of rock fragments. The best back-analysis determinations were obtained from (4), the cone, over all eight blends of fragments. The mean error was within -0,16 per cent of the true value, with a range of ± 1,872. This was for oversize contents of 5 to 20 per cent where a minimum 25 per cent of the photograph area was processed by digitizer. The worst results were from the apron dump at - 1,462 per cent for a mean error of ± 4,174 per cent. The intermediate results were from the undisturbed bench at -0,186 per cent with a mean error of ±2,862 per cent.

Jan 1, 1989

By A. J. Burger, F. L. D. Cloete

Tests indicated that effective recovery of pyrite from a coarse Witwatersrand quartzitic ore can be accomplished by intensified flotation in an air-sparged hydrocyclone. Air is fed through the porous cylindrical wall of the hydrocyclone into a swirling layer of slury. Hydrophobic particles are attached selectively to small air bubbles, which form a froth and are recovered through the overflow. Hydrophilic particles pass out in the underflow. A spigot in which flow is restricted by an orifice was found to be more successful in preventing blockage by wood chips than an annular opening between a pedestal and the cylinder wall. Pyrite recoveries of 85 to 93 per cent at grades of 35 to 40 per cent sulphur were obtained in the air-sparged hydroclone with residence times of about 1 second. Comparative tests in a batch flotation cell after 320 seconds yielded average recoveries of up to 96 per cent, but with a mean grade of 32,5 per cent sulphur. A high colector dosage of 120 g/t was required in the cyclone, compared with the 40 gft used in conventional operations. An air flowrate of about 150 I/min was adequate at a slury feed rate of 35l/min. Particle sizes between 38 and 106µm yielded the best flotation results.

Jan 1, 1988

By W. Soetaert, P. Dhar, H. R. Kota, M. Thornhill, S. Roelants, I. V. Chernyshova

Yeast-derived bola-amphiphiles have attracted considerable attention for their applications in various industrial sectors in recent years. However, only a few studies on this class of surfactant were reported to be relevant to mineral processing applications. In this paper, one of the novel surfactants, acidic glucolipid obtained from Candida bombicola sophorolipids and modified by using Penicillium decumbens naringinase substrate has been evaluated for its interaction with chalcocite and calcite minerals because of a new Cu-ore Nussir deposit in Norway containing calcite impurity. The interaction of glucolipid biosurfactant with copper sulphide and carbonate minerals was investigated with zeta potential, adsorption and FTIR studies, and also by Hallimond tube and bench scale flotation tests using pure minerals and Nussir copper ore, respectively. The results illustrate collector adsorption and flotation of copper sulfides at neutral pH. The bench-scale flotation results demonstrate that copper sulphides can be selectively floated from carbonate and silicate gangue minerals. This study underlines the glycolipid’s high potential for its use as collector for flotation of valuable copper sulphide minerals. Keywords: Flotation, biosurfactants, adsorption

Jan 1, 2020

By R. Gebrekristos

It is commonly accepted that three types of aquifers exist in the Bushveld Complex: (a) alluvial aquifers in areas of river courses, (b) weathered bedrock aquifer formed by the in-situ weathering of the bedrocks, (c) fractured aquifers underlying the weathered aquifers controlled by the regional and local fracturing of the crystalline rocks. Hydrogeological studies conducted in the Critical Zone of the Bushveld Complex in the western limb show that the UG2 pyroxenite layer is of a particular interest and has a unique aquifer property. It yields much of the groundwater inflow into some mines and can be classified as the most important aquifer in the vicinity of the mining zone. The UG2 pyroxenite aquifer is restricted to the dipping UG2 pyroxenite unit. The unit weathers more intensely than the surrounding norites and anorthosites and is characterized by deeper weathering horizons (two to three times deeper than the surrounding rocks). For much of the UG2 mining area between depths of 35 ? 80 m, stoping of the UG2 takes place approximately 5 ? 7 m below the UG2 pyroxenite aquifer, and usually there is no groundwater inflow into the mine workings. However, unsealed deep exploration boreholes intersecting the UG2 pyroxenite and reaching underground mine workings, or mine roofbolts penetrating the weathered pyroxenite aquifer from underneath, can result in significant groundwater inflows into the underground workings. The reason as to why the UG2 pyroxenite weathers more than the norites and anorthosites has not been fully studied but is suspected to be due to the bedding planes of the unit and mineralogical composition of the particular pyroxenes forming the unit, which result in preferential physical and chemical weathering under atmospheric conditions. The weathered pyroxenes form sand-sized, rounded grains with improved effective porosity and permeability suitable for the storage and passage of groundwater. The orientation of the pyroxenite aquifer can easily be determined as it dips with the Bushveld layered strata. No-flow boundaries can be assumed on the hanging- and footwall of the pyroxenite aquifer and the flow rates can be estimated using 2-dimentional analytical equations. However, this must be confirmed with strong conceptual models since the existence of a fracture network connecting the pyroxenite aquifer with the overlying weathered and/or underling fractured aquifers can complicate the system, lowering the accuracy of analytical models and necessitating the utilization of numerical models.

Jan 1, 2012

Notices TRANSPORTATION AND THE ENVIRO NMENT The 5th Quinquennial Convention of the S.A. Institution of Civil Engineers will take place at the Carlton Centre, Johannesburg, from 20th to 24th August, 1973. ENVIRONMENTAL ENGINEERING A conference on environmental engineering problems in industrialized and developing countries is to be held at the United Engineering Centre, New York, on 19th and 20th September, 1973. RABCEWICZ-COLLOQUY The Austrian Society for Geomechanics is to honour Professor Ladislaus V. Rabcewicz, on the occasion of his 80th birthday, with a meeting in Salzburg Congress Hall on 11th and 12th October, 1973. The themes of the four half-day sessions will be as follows. PYRO MET ALL URG ICAL EVENTS IN 1974 Diisseldorf is to be the venue for the following three events: International Iron and Steel Congress O.F.S. Branch Welkom THE MARCH GENERAL MEETING OF THE BRANCH WAS HELD IN THE ST. HELENA CLUB AT 8.00 P.M. ON TUESDAY, 6TH MARCH, 1973 O.F.S. Branch Welkom MINUTES OF A GENERAL MEETING HELD IN THE ST. HELENA CLUB ON WEDNESDAY, 16TH MAY, 1973, AT 8.00 P.M.

By L. A. Jagger

The world?s second largest producer of platinum, Impala Platinum Ltd, approved two new twin shaft projects at the end of September 2004, Nos. 16 and 20 Shafts. Both shaft projects are stand-alone entities and are being sunk from surface. Previously Impala had embarked on a strategy of extending the life of its third generation shafts by means declines. No. 16 Shaft is the first of a new fourth generation shaft complex, while No. 20 Shaft is the last of the third generation type shafts in the so-called shallow to intermediate mining zone. This paper details the basic designs of each project and covers the initial implementation. Although both projects are twin shaft systems, the access methods from the shafts to the reef horizon differ. Initiatives implemented to speed up the projects are also briefly covered.

Jan 1, 2006

Dr Andrew Cosgarea, Jr, Associate Director of Opera¬tions of the U.S. Mint, and Chairman of the Awards Committee of the International Precious Metals Institute, announced the IPMI award recipients for 1985. The awards were presented at the Institute's Annual Banquet in New York City on 11th June, 1985. The Distinguished Achievement Award was presented posthumously to Dr E.M. Savitsky, of the A.A. Baikow Institute of Metallurgy of the U.S.S.R., for a life-time career devoted to investigations on the properties of the platinum-group metals. Dr Savitsky investigated over 300 phase diagrams, which became the basis for the selection of alloys and the prediction of properties. He published over 300 technical papers during his career. Dr Savitsky died during the summer of 1984 while being considered for the IPMI Award. The Engelhard Henry J. Albert Award was presented to Dr Stephen J. Lippard, Professor of Chemistry, MIT, in recognition of his research contributions in platinum chemistry and its application to nucleic acids. This prize

Jan 1, 1985

By W. P. C. Duyvesteyn, J. R. Cutland, J. R. L. Russell

In 1970 it was decided to build a large new plant at the Chingola Division of N.C.C.M., Ltd., to treat concentrator tailings and leach residues with a low copper content by a leach-solvent extraction-electrowinning process. In order to assist in the establishment of the design parameters for the new plant, and to study the interaction of this plant with the existing leach-electrowinning plant, mathematical models, formulated as linear programs, have been developed and used extensively. The paper outlines the metallurgy of the plants and describes briefly the way in which the models have been formulated and used. The formulation involved the use of separable programming to form the products of some variables.

Jan 1, 2014

By Stephen Hughes

Ausmelt Top Submerged Lancing (TSL) Technology has gained widespread commercial acceptance in the lead and zinc industries, as an efficient and highly flexible pyrometallurgical reactor with accompanying excellent environmental performance. For the processing of lead and zinc bearing feed materials twenty one (21) Ausmelt furnaces are now in operation, under design or under construction. With recent increases in the value of both lead and zinc and an ever increasing focus on the sustainable use of resources, interest in the processing of secondary feed material sources as well as metal containing residues has substantially increased. Ausmelt Technology has proven to be well suited to the economic recovery of values from such sources. This has for example culminated in Ausmelt?s commitment to the Whyalla Zinc project as the owner/operator of a facility for the treatment of zinc bearing secondary feeds. This paper describes Ausmelt?s recent developments in the fields of lead and zinc processing, as well as further investigations into new processing areas, including the direct smelting of zinc concentrates. Ausmelt?s TSL Technology can now be regarded as Best Available Technology (BAT) for metal production.

Jan 1, 2008

By D. J. Hallbom

A new graphical method termed the ?Design Curve Diagram? (DCD) has been developed to analyse non-Newtonian pipe flow data by relating the plastic Karman number to the plastic Reynolds number. Since the plastic Karman number is directly proportional to the pressure loss gradient and the plastic Reynolds number is directly proportional to the velocity, the DCD is essentially a non-dimensional pipe flow curve. This makes the DCD conceptually easier than the commonly used Hedström-Moody diagram. While, the DCD was developed for the analysis of yield plastic fluids (e.g., Bingham plastics), it is equally applicable to Newtonian fluids.

Jan 1, 2007

By J. A. Maree

After the South Deep complex was purchased by Goldfields in 2006a re-feasibility study was done and the life of mine (LOM) was extended to 52 years. This also implied that the mine?s infrastructure would have to be enhanced. One of the changes was the proposal of five new main orepass systems to be excavated before the mine reaches full production in 2013. Excavations started to show signs of scaling, and in some cases, whole new excavations were lost. This particular area was exposed to very high stresses and the geology was prone to body delimination rendering the relevant areas unstable. This paper investigates the conditions at the location of one of the proposed orepass systems, and the best possible orientation was suggested to ensure that the orepass system would be stable and have a practical life. It was, however, found that the fourth leg of the orepass system would require further support to be classified as stable by the chief rock engineer and the section geologist of South Deep. Several support methods and orepass system linings would then be analysed and evaluated to give calculated recommendations on how to productively and practically support an orepass system. Keywords Main orepass system, stresses, body delamination, impact and abrasion, rock support, concrete lining.

Jan 1, 2011

The Copperbelt areas of Zambia and the Democratic Republic of Congo (DRC) have recently been seeing the development of a significant number of new projects. Due to the current economic climate, some of these projects have been delayed but the region remains an important resource for copper and cobalt for future years. Many of these projects will utilize an agitation leach followed by solvent extraction and electrowinning to recover both copper and cobalt. The flowsheet route for copper is fairly well established while the processing options for cobalt vary considerably depending on the final product (metal or salt) the operator wishes to make. The mineralogy of ores in the area is typically associated with high gangue acid consumption during the leaching process. This has resulted in acid availability to the area being constrained and acid prices have risen accordingly. Agitation leach circuits, typically, have a tight water balance which needs to be maintained and a bleed of process liquor needs to be continuously removed from the circuit in order to maintain this balance. This bleed, typically, contains fairly high levels of acid and requires neutralization prior to tailings disposal or secondary metal recovery. It is, therefore, desirable to minimize the acid concentration in this bleed stream in order to decrease total acid requirements and neutralization costs for the process plant. An in depth case study by Cognis and Bateman Engineering evaluated three different flowsheets with the aim of determining relative operating costs between the three alternatives, together with differences in plant capital cost requirements.

Jan 1, 2009

Notices Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to Rl00 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute. NEW PUPLICATION Bougainville-the establishment of a copper mine. St. Kilda (Australia), 'Foundations', 1973. The editors of Foundations, Australia's journal of architecture, engineering, and construction, are preparing the above book for publication late in 1973. The story of Bougainville is told and illustrated NIM REPORTS Report No. 1503 Fast-neutron-activation analysis for the determination of oxygen m rock sam ples. Report No. 1514 The determination by X-ray-fluorescence spectrometry of minor amounts of niobium and tantalum in geological materials. Report No. 1530 AUREOL - an X-ray-absorption analyser for the determination of the uranium on loaded resin in ionexchange plants. Report No. 1534 The determination, by atomicabsorption spectrophotometry, of noble metals in the presence of sodium, barium, or sulphate ions. A comparison of uranium and lanthanum as 'releasing agents.

Jan 10, 1973

By Alexandra Amiel

Tarkwa Gold Mine is owned by Gold Fields Ghana, IAMGOLD and the Government of the Republic of Ghana in a 71%, 19% and 10% ratio. The mine is operated by Gold Fields Ghana. This large, low-grade, open pit, gold mining operation is located in Tarkwa, in the Western Region of Ghana, approximately 320 kilometres by road, west of Accra, the capital of Ghana, West Africa. In the Financial year ended June 2007, the operation mined a total of 108 million tonnes of which 22 million tonnes was ore. The mined ore is processed through three gyratory crushers supplying two heap leach pads (North and South) and a carbon-in-leach (CIL) plant. Before the 6 Sigma project commenced, the current fragmentation was resulting in sub-optimal feed size to these crushers. It was decided to use 6 Sigma methodology to improve the fragmentation. A defect was defined as a fragmentation analysis indicating less than 95% passing 750 mm. The objective was to improve fragmentation in order to achieve a constant throughput to the north heap leach crusher of 1500 t/hr, a 5% increase in pit loading efficiency and a 50% decrease in rock breaker hours, equipment damage costs and in-pit sheeting costs respectively. However, this was not to be achieved at the expense of grade control as Tarkwa is exploiting a low grade, high volume deposit and therefore ore dilution must be kept to a minimum. This paper is intended to take the reader through the various 6 Sigma phases of the project (Define ? Measure ? Analyse ? Improve ? Control) which have resulted in a 10% reduction in loading times, of which half has been attributed to improved fragmentation, as well as a substantial increase in blasted stocks. The focus has been on both drilling and blasting parameters as both processes had to be taken into account. These parameters are technical but personnel factors were also identified and dealt with as they arose. In order to measure the impact of any change in the process parameters on the fragmentation size distribution, cameras have been acquired. One has been installed looking into the bowl of the north crusher and the other one was dedicated to field observation, of individual blasts. Both are used for on-going fragmentation analysis. At Tarkwa, mining efficiency is strongly dependent on good fragmentation as well as the presence of un-blasted ?toes? on the pit floors. Crusher throughput depends on an acceptable ore fragment size. Compliance to plan with regards to actual hole depths was temporarily monitored by manual hole dipping, but, this is now being replaced with a fully automated Drill Data Management system developed by Sandvik and Modular Mining. The Six Sigma methodologies, using control charts based on data collected in the field, allowed the mine to improve methods with regards to the control of blasted material. It also enforced the implementation of a quality control programme encompassing the entire Drill and Blast process.

Jan 1, 2008

By C. van Loggerenbergt, P. E. Ventert

A strong incentive exists for the coal-preparation engineer to improve plant efficiency by modifying circuits and upgrading process equipment, since these result in lower production costs and more valuable plant products. At the Grootegeluk Coal Mine, it was found that the overall plant efficiency could be improved by modifications to the dense-medium circuits, the installation of additional process equipment for the recovery of fine coal, and improvement of the fine-material processing circuit. Apart from these modifications, there is still potential to increase the plant efficiency, particularly in the utilization of plant waste, the recovery of slimes, and even the improvement of cycloning performance as a result of new cyclone design. This paper points to the potential wealth locked up in existing coal-preparation plants, and shows how the coal-preparation engineer, with new technology at his disposal, can unlock this wealth.

Jan 1, 1992

By B. P. Gilbertson

In her wonderful book, 'The Guns of August', historian Barbara Tuchman tells us that the French war plan for 1914 was dedicated entirely to an offensive strategy, not a defensive one. Plan 17, as it was called, concentrated everything on a French advance to the Rhine, leaving the French left virtually unguarded. This strategy could only be justified by the fixed belief that the Germans could not deploy sufficient manpower to extend their invasion around through western Belgium and the low provinces; and this in turn was based on the belief that the Germans would never use reserve troops in the front line. Al evidence to the contrary was ignored. But when the war came, the Germans followed Count Von Schlieffen's plan; they did use reserves in the front line and they did come the long way around on the west. The result- as you know-was a protracted war, with fearful consequences for the rest of our century.

Jan 1, 1994

By M. H. Lampen

The SILAG Material Tracking System MTS monitors and controls the complete material flow throughout the plant - and even companywide. The customized system developed by Siemens especially for bulk material handling applications enables companies to track bulk material from the mine to the harbor, to the steel mill or to the power plant. All relevant material data is available at every single step of the material’s journey. SILAG is an open, scalable system based on Windows NT / 2000. Using standard interfaces of Windows NT, like API, ODBC, SQL and socket technology, the system is very flexible and can easily be tailored to meet different requirements. SILAG can be used as a stand-alone solution or - if complete plant control and visualization is required - as a component of a fully integrated automation system with the Win CC HMI system and the PCS7 process control. In contrast to conventional material tracking systems, SILAG offers many advantages. - The Material Tracking System is an object oriented, online to the process, linked system. All changes in the plant during operation e.g. selecting another conveyor route, start and stop etc. will be automatically detected and will influence the calculation. - The systems is able to split and blend material (quantity and quality).Measurements of tonnage, volume or quality analysis can be linked online to the system. Each movement of material is monitored by the system and leads to online recalculations of the images and databases. - All material data is based on 3D-stockpile images, which are calculated by an internal mathematical model based on quantity and quality information. - If a laser scanner is available on a stockyard machine it can be taken to update the profile directly from the piles. - Efficient control and report functions are available on each, free selectable point of the total plant.

Sep 1, 2001

By W. J. Cruise

This paper reports on a test that was conducted underground in a mine for two years on the following: pipes coated with paint, fusion-bonded powder, metal, or impregnated tape; and aluminium, stainless-steel, 3CR12, and plastic pipes. It was found that the degree of corrosivity and mechanical damage increases substantially from the shaft of a mine towards the stope. Thus, the range of coatings that can be used successfully is fairly large in the shaft and haulageways, but corrosion-resistant materials, especially corrosion-resistant steels, need to be used close to the stope. A study of the relative costs involved showed the costs of pipes of low-carbon steel and unplasticized polyvinyl chloride to be lowest, and those of epoxy-coated steel pipes to be highest.

Jan 1, 1985