Search Documents

By Y. -L. Chiang

Paper written on project work carried out in partial fulfilment of BSc (Eng) (Chemical) The generation and control of manganese sulphide particle size distribution using various mixing configurations were investigated. Specifically, this paper discusses how varying mixing intensities on a macro and micro scale affect the resultant manganese sulphide particle size distribution (PSD) at a constant concentration. The mixing variations were achieved using various Y- and T-mixers as premixing devices into a jacketed, agitated vessel. The reagents used to generate the seeds were aqueous manganese sulphate and sodium sulphide solutions. The results showed that the absence of micromixing resulted in very poor control of the particle size distribution, the particle size and the number of particles produced. This was due to the fact that the macromixing time is much greater than the corresponding precipitation time, resulting in different mixing regions existing within the reactor. From the micromixing experiments, the T?mixer was found to be the most effective mixing device at lower concentrations due to the T-mixer providing a faster mixing time than the other mixing configurations, thereby effectively localizing the supersaturation and hence controlling the precipitation. The results obtained from the direct addition without the extension pipe (i.e. short mixing time) indicated a general increase in mean particle size and decrease in total particle number at reagent concentration of 0.007 mol.dm-3as compared to the corresponding micromixing experiments. The phenomenon may be due to incomplete crystallization at the immediate exit of the mixing device. Further experiments need to be conducted before any conclusions can be drawn about the precipitation mechanisms.

Jan 1, 2007

By Y. Zhan1, T. Moodley, M. A. H. Zahid

Mining operations are under growing pressure to improve safety and efficiency while dealing with aging infrastructure, complex processes, and workforce constraints. Although many sites are equipped with surveillance cameras and control systems, critical events often go unmonitored or under-analysed due to the lack of intelligent interpretation tools. Cameras typically act as passive recorders, requiring manual review by control room operators; a process that is labour-intensive, error-prone, and reactive. Vision AI is emerging as a transformative solution, combining computer vision and artificial intelligence to deliver real-time, actionable insights. This technology has evolved along two key phases: traditional object detection, and more recently, multimodal large language model integration. This paper presents solution architectures, deployment results, and key insights from real-world implementations across underground operations, open-pit truck-shovel operations, and smelter operations, demonstrating how Vision AI is reshaping mining operations to become safer, more efficient, and more intelligent.

Mar 6, 2026

By Z-B. Cheng, X-J. Liu

"Intensive mining of shallow coal seams tends to result in severe subsidence of the ground surface. Surface subsidence is a complex dynamic spatiotemporal process that constantly changes as mining advances. With Liangshuijing coal mine as a case study, 3DEC numerical software was used to simulate the development of the moving subsidence field from open-off cut to full subsidence on the working face. The results demonstrate that the formation of a subsidence field is directly related to the coal seam depth H and the extent of the mine workings. Taking the advance distance of the working face as the unit of scale, the process of surface subsidence can be divided into four stages: micro-change (H/ p), the development of surface subsidence (2H/ p), the formation of a movement subsidence field (3H/ p), and dynamic balance (4H/ p). The changing movement of a subsidence field can be fully described by the characteristics of surface subsidence value, curve slope, and the inflection position. The results provide important technical support for predicting surface subsidence and the temporal–spatial evolution features of mining subsidence. IntroductionChina’s coal output was about 3.52 Gt in 2017 (China National Coal Association, 2018), making it the largest coal producer in the world, accounting for almost half of total world coal production. Coal production and distribution play a vital role in the energy industry of China. However, entire overlying strata, from coal seam to surface, are disturbed as a result of long-term, high-intensity and large-scale mining, causing surface subsidence. This results in groundwater loss, surface desertification, vegetation loss, and mud-rock flows. These issues have become topics of common concern throughout society. According to related research results (Liu 2008), the area of surface subsidence caused by coal mining in China has reached about 600 000 ha, some 0.2 ha (and up to 0.42 ha) of surface subsidence for every 10 000 t of coal produced. Surface subsidence disasters not only damage buildings, water conservancy, transportation infrastructure, and farmland, but also cause adverse effects on individual and community lifestyles, environmental hygiene, and economic development. Deterioration of the ecological environment in mining areas has a long history and is very harmful (Lu, 2015)."

Feb 1, 2019

By J. L. Havenga, L. J. van der Walt, J. T. Nel

"SynopsisThe development of plasma technology at Necsa started in the early 1980s, when the applicability of high-temperature plasmas in the nuclear fuel cycle was investigated. Since 1995, this plasma expertise has expanded to other industrial applications, for example mineral beneficiation, nanotechnology, fluorocarbon production and waste treatment, all of which are also of relevance to the nuclear industry.Necsa has demonstrated the manufacture of plasma-dissociated zircon, zirconium metal powder, carbon nanotubes, silicon carbide (SiC), zirconium carbide (ZrC) and boron carbide (B4C) at the laboratory and pilot plant scale. These materials are commonly used in the nuclear industry. Zirconium alloys are used as fuel cladding material for nuclear fuel assemblies.Necsa manufactured the monomer tetrafluoroethylene (TFE), using 150 and 450 kW DC plasma systems, from which the polymer polytetrafluoroethylene (PTFE) was synthesized for use in filters and as seals in nuclear plants. With the nuclear renaissance at hand, it was demonstrated that plasma technology can be used to produce hydrofluoric acid (HF), which is used in the manufacture of fluorine gas (F2) for the production of uranium hexafluoride (UF6) directly from the mineral calcium fluoride (CaF2) without the use of sulphuric acid as in the conventional process. The recovery of valuable uranium from nuclear waste such as filters, oils, and solids with plasma processes will also be discussed. The destruction of low-level nuclear waste by a plasma gasification system can reduce the volume of this waste by several orders in magnitude, resulting in huge savings in the storage costs. Another product of plasma technology is the encapsulation process for nuclear waste and the production of vitrified product, which could be used as filler material for medium-level nuclear waste.IntroductionDuring the 1980s, a plasma research and development programme was launched at the erstwhile Uranium Enrichment Corporation of South Africa (UCOR) at Valindaba outside Pretoria. The main purpose of this programme was to develop alternative and more economical processes for the processing and manufacturing of uranium compounds used in the nuclear fuel cycle. The conversion of UO2 (as received from uranium mines) to UF6, which is needed for enrichment, conventionally involves several laborious, expensive, chemical processing steps. Plasma processes can eliminate several of the intermediate steps. Enriched UF6 is converted to UO2, which is pressed into pellets that are used in nuclear power plants. Plasma technology could also be used in a modified and optimized conversion process."

Jan 1, 2015

By N. V. Moraka

Mining companies are required by law to improve representation of women on their boards. However, progress in this regard has been slow. Boards of directors play an important role in formulating corporate strategy, risk assessment, and effective governance for sustained financial performance. Although some women have successfully maintained board seats, others have been unable to do so. It is difficult to ascertain whether women are being appointed as tokens to satisfy social pressures, as little is known about the experiences of women board members in mining, which may inform or refute tokenism. In-depth interviews were conducted with 20 women and 16 men across six listed mining companies. Thematic data analysis revealed evidence of tokenism where recruitment to mining boards is compliance-based and is informally driven by influential directors. Adverse boardroom experiences that further confirmed tokenism were reported by women, such as disregarding their contributions, condescending behaviour, and limited influence in decision-making, while other women sought to validate their competence and oppose social exclusion. This study recommends that a strong Board Chair and nominations committee is critical to ensure sustainable recruitment of competent and suitably qualified women; and further foster a culture of inclusivity and valuing gender-diverse boards.

Dec 13, 2023

By S. Moolla, R. Lynch, S. Brijraj

A reliable method to locate microseismic evets is an important objective for routine mine seismic monitoring. We developed an algorithm that can automatically and reliably locate an event from a single uniaxial trace. Signals created by microseismic events are recorded as seismograms that consist of direct P- and S-waves as well as the waves reflected off the underground excavations. We take advantage of the extra complexity these reflections introduce as they make the signal more unique. In our investigation we cross-correlated unaltered synthetic seismograms against trial waveforms created from a linear combination of appropriate waveforms from a library of numerically calculated strain Green’s tensors. We use a single uniaxial synthetic seismogram to invert for the source location, six moment tensor components, and frequency. The resulting cost functions are constructed as maximal correlations at each node in the mine grid through the true source x-planes. This function is maximized by differential evolution to simultaneously yield the source parameters. Sensitivity tests such as shifting the mine plans and altering the background velocities of the media are investigated to test the robustness of the method. We contaminate the data with 40% white noise to test the resolution against simulated real recorded seismograms. The method is demonstrated using synthetic data calculated with a realistic underground 3D velocity model.

Jun 10, 2024

By A. Chryss, L. Pullum

Shear-thickening suspensions abound throughout the hydraulic conveying industry; at least this is the perception of many engineers running plants where hydraulic conveying is commonplace. In reality, shear thickening behaviour is limited, in the main, to high concentrations of fine particles, including colloidal and biological suspensions, at moderate to high shear rates. In the authors? experience most cases of shear-thickening behaviour have been either simple ?coarse? particle interactions, poor instrumentation techniques, or both. In some cases these were obviously heterogeneous flows, while in others flows that were homogenous, or were thought to be homogenous. Examples, which illustrate this erroneous perception are given. However, the trend towards pastes and complex suspensions that use high concentration carrier fluids means that the underlying slurries for many of these flows may now be truly shear-thickening. Unfortunately, suspensions that might exhibit shear thickening also invariably exhibit slip, or wall-particle depletion. These separate phenomena are difficult to resolve experimentally and many observations of apparent shear-thickening behaviour are in fact obscured or convoluted by slip effects. A method is presented whereby the true flow properties of these high concentration suspensions, and hence accurate prediction of pipeline flows, can be made using a parallel plate rheometer.

Jan 1, 2007

By N. Naude, L. S. Leal Filho, M. P. Tshazi

In this paper, the authors performed experiments in the Denver and Leeds laboratory flotation devices at the University of Pretoria at various particle sizes to evaluate the performance of the devices. Quartz was used in a single mineral system at discrete sizes fractions, -25 μm, +25- 45 μm, +45-75 μm, and +75-106 μm. Hydrodynamic analysis, based on dimensionless power and Reynolds numbers, indicated that the Leeds cell required higher power input to achieve comparable flow conditions. Specifically, the Leeds cell exhibited an average power number of 1.03, whereas the Denver cell averaged 0.77 within the same impeller speed range of 1000 rpm–1500 rpm. For comparative flotation performance, impeller speeds were calibrated, resulting in operating speeds of 1200 rpm for the Denver cell and 1400 rpm for the Leeds cell. The cells performed similarly at two coarser-sized fractions. However, some deviations were observed in the finer particle size range. The -25 μm (fine) fraction initially achieved a recovery of only 15%. An additional reagent dosage was required to enhance the recovery of this fraction significantly. These findings highlighted the influence of particle size on flotation recovery. For all experiments, the Denver laboratory flotation cell outperformed (defined by higher recovery) the Leeds device, while still operating at a lower impeller speed. This advantage can be attributed to its impeller-stator design and air dispersion features, effectively overcoming slurry resistance and resulting in superior flotation performance compared to the Leeds cell.

May 27, 2025

By C. Liu, F. Ye

"To extend the variety of lump ores that are used in the COREX shaft furnace and to optimize iron ore blending, the original evaluation method for iron ores that was proposed by Voestalpine AG has been improved. Physicochemical and metallurgical properties of iron ores, including Sishen lump ore and CVRD pellets, which are currently used in the COREX process, and three other lump ores, were assessed and compared. Ore matching principles were proposed and five optimized iron ore blending schemes designed and verified by laboratory experiments to prove the effectiveness of the improved evaluation method. The replacement of Sishen lump ore by the alternative L2 and L3 lump ores without varying the proportion of CVRD pellets could improve the degree of reduction and rate of metallization, and decrease the bonding index. Based on the results of laboratory test work and industrial- trials, an ore blending scheme of 60% CVRD, 20% L2, and 20% L3 is recommended for use in the COREX process. IntroductionIn recent years, problems such as environmental pollution and a shortage of coke and coal resources for blast-furnace ironmaking have become increasingly apparent. Based on sustainable developments in the iron- and steelmaking industries, the environmentally friendly COREX smelting-reduction process with low energy consumption was developed and introduced (Zhou and Du, 2013; Song, Lv, and Yin, 2015; Xu et al., 2016; Kurunov, 2010). The evaluation system for lump ore that was proposed by Voestalpine AG recommends that only Sishen lump ore from South Africa be used in the COREX process, because of the stringent physicochemical and metallurgical property requirements. This situation significantly hampers improvements to the technical and economic aspects of the COREX ironmaking process, especially in China (Eberle, Siuka, and Bohm, 2006). No theoretical or technical basis has been provided for the evaluation system, and the assessment approach for iron ores also presents problems that need to be discussed and resolved.The COREX process consists of two reactors: the prereduction shaft furnace and the melting gasifier as shown in Figure 1 (Wu et al., 2017). Pellets and lump ores which are charged to the prereduction shaft should have a good reducibility and metallization with a low degradation index (Li et al., 2016; Wu et al., 2011; Kumar et al., 2009; Kang, Gupta, and Sahajwalla, 2007). The properties and microstructure of the iron ore pellets which are required to achieve a high productivity and a lower fuel rate in the COREX process have been investigated (Umadevi et al., 2011). Some efforts have also been made to investigate the behaviour of lump ores in the COREX shaft furnace, including the disintegration characteristics and the reduction degradation (Umadevi et al., 2011; Zhou et al., 2015; Xu et al., 2013; Li, Feng, and Zou, 2013; Hou et al., 2014). However, few studies have focused on the optimization of ore blending for partial or total substitution of the expensive Sishen lump ore by other, cheaper lump ores to reduce the production cost. The technology for the utilization of blended lump ores in the COREX process is still in its early development stages (Zhou et al., 2017; You et al., 2017)."

May 1, 2019

By R. T. Rudd

DISCUSSION R. T. RUDD I have the following comments on Mr Bosman's paper. Before giving the company permission to discharge neutralized mine drainage containing 1800 mg/l of dissolved solids into a public stream, my Department had to consider the matter from both the legal and the practical viewpoint.

Jan 4, 1974

COUNCIL AND STANDING COMMITTEES - 1973-1974 Office Bearers: P. W. J. van Rensburg (President), Professor R. P. Plewman and Dr R. E. Robinson (Vice Presidents), J. K. E. Douglas (Honorary Treasurer), and Dr J. P. Hugo (Immediate Past President). Elected Members of Council: Dr M. G. Atmore, G. H. Grange, Dr P. R. Jochens, J. G. Kirchner, Dr D. I. Legge, W. W. Malan, Dr M. D. G. Salamon, L. W. P. van den Bosch, D. A. Viljoen, P. A. von Wielligh. Branch Chairmen: B. T. Hosking (Witbank-Middelburg Branch), E. T. Wilson (Orange Free State Branch). Past Presidents Serving on Council: R. J. Adamson, M. Barcza, H. Britten, H. E. Cross, Professor J. de V. Lambrechts, R. C. J. Goode, Professor D. D. Howat, D. M. Jamieson, D. G. Maxwell, Dr J. T. McIntyre, V. C. Robinson. Ten Council meetings were held during the year, with an average attendance of 19, and the standing committees held 30 meetings. COMMITTEE CHAIRMEN Membership, Dr R. E. Robinson ; Metallurgical Colloquia, Dr R. E. Robinson ; Mining Colloquia, L. W. P. van den Bosch; Awards, P. W. J. van Rensburg; Excursions, P. A. von Wielligh; Dinner, G. H. Grange ; Constitution, Rules and Policy, Dr J. P. Hugo; Adjudicating, P. W. J. van Rensburg; Mines and Works, W. W. Malan; Education, Dr J. P. Hugo. REPRESENTATIVES ON OTHER BODIES Associated Scientific and Technical Societies: Members : V. C. Robinson and D. G. Maxwell Alternates : P. W. J. van Rensburg and Dr J. P. Hugo. Federation of Societies of Professional Engineers Members : J. K. E. Douglas and P. W. J. van Rensburg Alternates : Dr J. P. Hugo and G. H. Grange. South African Council for Professional Engineers Members : R. C. J. Goode and J. K. E. Douglas Alternates: G. H. Grange and Dr R. E. Robinson. Engineers' Liaison Committee (Pretoria): Member: Professor J. de V. Lambrechts Alternate : Dr J. P. Hugo. MEMBERSHIP Seventeen Fellows and Members, twenty-three Graduates, ten Associate Members, twenty-two Associates, thirty-four Students, and seven Company Affiliates were elected during the year. Eleven Fellows and four Members were admitted to retired membership. Five Fellows were elected to Honorary Life Membership. Four Members, two Graduates, and one Student were transferred to Fellows ; eleven Graduates and Students were transferred to Members ; eight Students to Graduates; and four Students to Associates. A statement of membership as at June 30th 1974 and the end of the previous year is given in the following tabulation 30th - 30th June, - June, 1973 - 1974 Honorary Life Fellows 4 - 9 Honorary Fellows 9 - 8 Life Fellows 177 - 170 Fellows 536 - 544 Members 487 - 512 Associate Members - - 10 Graduates 128 - 130 Associates 186 - 194 Students 183 - 173 Company Affiliates 64 - 70 1 774 - 1 820 OBITUARIES Your Council records with deep regret the death during the year of the following members : Dr P. N. Lategan and Dr O. A. Jackson, Honorary Life Fellows and Past Presidents; C. Airth, T. L. Blunt, J. B. Dennison, A. E. Frazer, C. L. Lamb, V. O. Reid, K. Richardson and D. G. Roberts, Life Fellows ; H. F. Allan, J. T. Beaumont, M. Eisenstein, J. C. Hall, C. F. Louw, H. H. McGregor, R. Murchison, and J. E. Williamson, Fellows; and R. B. Miles, Associate. FINANCE The annual accounts, which follow this report, reflect a healthy position and show that measures taken by Council over the last few years to boost income have been successful. A higher income was needed not only to meet rising costs but also so that the services provided by the Institute for its members could be expanded. This year's income of R55 025 showed a further increase compared with last year's figure of R48 307. Income from subscriptions was higher mainly owing to an increased number of Company Affiliates, and this is indicative of the support given by mining and metallurgical companies to the good work being done by the Institute. Further sales of publications of the symposia held over the last few years again made a useful contribution to income of R4560. The first Winter School held in 1973 yielded a surplus of R7495 after the expenses had been deducted from the income received from registration fees. The cost of administering the Institute increased by R2212 compared with the previous year. Included in this was a donation of R1000 to the A.S. & T.S. Trust Fund. The cost of publishing and printing the Journal increased by R2034, but advertising and extraneous sales of the Journal were higher, with the result that the net cost of the

Jan 10, 1974

By M. J. Nicol

On page 51, the equation numbered.... On page 52, the equation numbered .... On page 53, the arrangement of the equation.... Canadian reports Asbestos by G.O. Vagt.l0 pp. Chromium by D. G. Law-West. 6 pp. Iron and Steel by T. R. Mclnnis. 15 pp. Titanium and Titanium Dioxide by M. A. Boucher. 7 pp. Vanadium by D. Shaw. 7 pp.

Jan 1, 1984

By B. Geelhoed

Gy's formula for the variance of the fundamental sampling error (FSE) is based on a model that assumes independent selections of particles. A generalization of this model, which can theoretically lead to more realistic representation of actual sampling processes, was, for the first time, experimentally verified by repeated sampling from a well-mixed batch consisting of particles of zirconium silicate of two different sizes. The predictions for the sampling variance made in Gy?s theory and in the more general model were compared with the experimentally observed sampling variance. During the experiment performed here, the variance prediction made in the theory of Gy ranges from 0.96 × 10?7(g2/g2) to 0.95 × 10?7(g2/g2), which is approximately a factor 60 lower than the experimentally observed variance (5.76 × 10?6(g2/g2)). The difference between the Gy prediction and the experimentally observed variance cannot be fully explained by the uncertainty in the experimentally obtained variance due to the finite number of degrees of freedom. Therefore, the difference is likely to be a significant effect. This shows that, under the experimental conditions, Gy?s formula for the variance of the FSE probably undervalues the sampling variance, unless an empirical correction factor for grouping and segregation is applied in the theory of Gy. The new theory resulted in a variance prediction of 6.00 × 10?6(g2/g2), which is much closer to the observed variance than the Gy prediction. This indicates that the generalization of Gy?s theory offers an outlook for providing a better variance prediction than the Gy predictor in the case of dependencies between particle selections. The results are discussed. Keywords: sampling, variance, parameter for the dependent selection of particles, Gy, experiment.

Jan 1, 2009

By O. I. Rychkova, M. N. Sycheva, E. V. Poryadochnova, G. V. Sedelnikova

Deposits of copper-porphyry type occupy a leading position in the mineral resource base of the world copper industry. They are characterized by large and gigantic scales, often complex composition, their development is carried out in an open way. The raw material base of the Russian copper industry is mainly sulfide copper-Nickel and copper-pyrite ores. Exploration of copper-porphyry deposits and the creation of long-term large mining facilities on their basis is one of the most promising and priority tasks for the Russian industry. This task is especially acute for the copper enterprises of the Urals in connection with the depletion of copper - pyrite ore reserves. In recent years, Russia has carried out a large complex of studies on the composition and technology of processing of copper-porphyry ores of different subtypes. In this work the complex poor copper-molybdenum-gold ore of one of the deposits is investigated. The chemical and mineral composition of the ore containing 0.49% copper, 0.020% molybdenum, 0.39 g/t gold, 5.85 g/t silver was determined. The forms of finding metals and their distribution by size classes are established. The dependence of extraction of metals into concentrates of collective-selective flotation on the size of ore grinding, pH of the medium, reagent consumption is shown. Under optimal flotation conditions, copper concentrate with 18.6% copper content and 92.32% extraction and molybdenum concentrate with 21.5% molybdenum content and 73.4% extraction were obtained. With a high concentration of molybdenum in selective flotation products, it is possible to conclude about the expected molybdenum concentrate with a content of 45% and a recovery of 70%. The associated extraction of gold and silver into copper concentrate is 76.8 % and 73.4%. Keywords: Collective-selective flotation, copper, molybdenum, porphyry ore, grinding, pH, reagents

Jan 1, 2020

By L. J. Gerber, O. D. Eniowo, L. D. Meyer, S. R. Kilambo

Artisanal and small-scale mining (ASM) operations continue to grow across sub-Saharan Africa and serve as a source of livelihood to many rural communities. Owing to safety, health, environmental, and social concerns, the occupation has been regarded as a menace in several sub-Sahara African countries. Recent studies in the field of ASM prescribe formalization as a way to tame its excesses while enhancing its potential. This paper explores the concept of formalization as it relates to ASM and how it is being affected by the funding situation. The paper seeks to address the question as to whether formalization of artisanal mining operations can achieve the desired results in view of the lingering credit constraints in this mining subsector. It is recommended that, as a way of extending the scope of formalization, focus should be placed not only on access to credit in ASM but also towards optimizing the creditworthiness of ASM firms, with the goal of improving the viability of the operations.

Mar 2, 2022

By M. Åstrand, M. Johansson

"Advanced planning and automation are increasingly important in modern mines. Sophisticated methods for long-term mine planning are often used, and the advent of autonomous machines makes the actual operation more predictable. However, the interface between these two timescales, i.e. the scheduling of the mobile production fleet, often limits the ability to operate mines at maximum profitability. We show how scheduling the production fleet in an underground mine can be modelled as a flow shop. A flow shop is a general abstract process formulation that captures the key properties of a scheduling problem without going into specific details. Thus, the flow shop enables mine scheduling to reap the benefits of scheduling research from other industries. We review recent results from the mining community and the flow shop community, and introduce scheduling methods used in these two fields. This work aims at providing value to researchers from the mining community who want to leverage their skill set, as well as to theoretical researchers by presenting the mining process as a potential application area. Lastly, we discuss the results, and outline some future challenges and opportunities facing the industry. IntroductionThe margins in underground mining are constantly under pressure since costs increase as the mine becomes deeper. One major component influencing the operational performance, and thus the profitability of an underground mine, is how the mobile machinery and staff are coordinated. Today, the coordination of the underground fleet, i.e. scheduling of the machines, is mostly done manually, with methods that are stretched to their limit and with no guarantees on performance. According to a survey of more than 200 high-level executives in mining companies around the world (Mincom, 2011), the top challenge for modern mines is to maximize production effectiveness, rather than improving the reliability of individual items of equipment. This highlights the importance of coordination on a system level.The effectiveness of mine production can be increased by introducing supportive algorithms in the scheduling process. These algorithms enable mines to construct optimized schedules with respect to custom metrics. Additionally, manual scheduling is a tedious and error-prone task where the performance is heavily dependent on the scheduler. To reduce the staff dependency, supportive algorithms can help to achieve more uniform outcomes, resulting in a more predictable process. In turn, this increases the transparency of the mining process through the entire production chain. It is worth noting that automatic scheduling has proved beneficial in many other industries, such as chemicals and metals (Floudas and Lin, 2004; Tang et al., 2001)."

Dec 1, 2018

By M. M. Masood, G. Y. Raju, T. Verma

The inverse velocity method has proven to be an effective approach for predicting slope failures in surface mines by analysing displacement monitoring data. However, the accuracy of inverse velocity method predictions is significantly affected by instrumental noise and natural environmental variations, which influence the identification of different deformation stages. To enhance predictive accuracy, this study applies and evaluates three filtering techniques to velocity time series data: Exponential smoothing filter, short-term smoothing filter, long-term smoothing filter and also compares it to raw data (no filtering). A refined prediction framework, that is, filtered inverse velocity method analyser, is proposed to improve slope failure forecasting in surface mining operations. The results demonstrate that filter selection plays a crucial role in optimising failure time predictions, offering valuable insights for geotechnical monitoring and early warning systems in surface mines.

Sep 1, 2025

By F. P. A. Robinson, C. R. Thomas

Stress-corrosion studies on materials used for surgical implants * by C. R. THOMAS and F. P. A. ROBINSON Samples of Vitallium (a cobalt-chromium alloy), 316L stainless steel, and titanium T318 were subjected to the boiling magnesium chloride test so thattheir susceptibility to stress-corrosion cracking could be determined, and their behaviour under service conditions was then assessed. Stress-corrosion cracking was confined to the stainless-steel samples, while gross pitting was detected in the samples of forged Vitallium. It was concluded that the use of stainless steel should be avoided for long-term surgical implants. Surface imperfections on the stainless steel are generally the cause of pitting, from which stress-corrosion cracks are sometimes propagated.

Jan 11, 1976

By H. E. Parkinson, Y. P. Chugh

About 90 percent of the coal mined underground in the U.S.A. today is mined by the room-and-pillar system. The productivity of the system dropped from about 14,1t per man-day in 1969 to about 7,3 t per man-day in 1978. Since 1974, the U.S. Department of Energy (formerly the U.S. Bureau of Mines) has been engaged in research to improve the production and productivity of the room-and-pillar system. The effort involves the development of integrated, automated, and remote-controlled equipment and systems including remote-controlled continuous miners, automated miner-bolters, automated extraction systems, continuous haulage systems for use behind miners, and remote-controlled equipment for miners, bolters, and shuttle cars. These systems are discussed briefly, the discussion being related primarily to coal winning, although the concepts could be utilized in room-and-pillar systems in mines other than coal mines.

Jan 1, 1981

The second annual student prize giving function of the South African Institute of Mining and Metallurgy was held in the Van der Byl Hall, University of Pretoria, on Thursday, 10th March, 1978. The main address (see opposite page) was given by Dr T. F. Muller, Chairman of Iscor.

Jan 1, 1978