Search Documents

By K. L. Rubow

"Diesel exhaust and mineral dust concentrations have been measured for aerosols generated in the laboratory and as found in five underground coal mines- 3 utiliting diesel-powered hallage equipment and two electric-powered equipment. Two source apportionment techniques have been applied to differentiate between the mineral dust and diesel exhaust aerosol concentrations. The first technique, using a microbrifke uniform deposit impactor CMOUDI) for size selective sampling, is based on modeling aerosol size and the premise that the diesel exhaust portion of .the aerosol is predom1nately submicrometer and the mineral dust portion is mostly greater that one micrometer in size. The second technique, Chemical Mass Balance CCMB) modeling, was used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results. ,The MOUDI size distribution data were modeled to obtain parameters describing the fine and course fractions of the sampled aerosol and to estimate the contributions to each mode from both mineral ·dust and diesel exhaust aerosol sources. The results showed the size distribution of the mixed aerosols exhibited two definite modes with the minimum between the modes occurring at 0.8 um. For the diesel equipped mines, this analysts yielded an average value for the fraction of the fine aerosol attributable to mineral dust of 1 pct. Less than 5 pct of the coal mine diesel aerosol was found in the coarse size fraction. CMB analysis confirms the original premise for using aerosol size to separate diesel exhaust and mineral dust aerosol during sampling."

Jan 1, 1988

By F. P. Haver

The Bureau of Mines developed a process to extract about 90 percent of the sulfur from molybdenite flotation concentrate by compacting the concentrate with one-quarter of its weight of aluminum powder, heating it at 800° C for 30 minutes, and then allowing the product to react with water. This thermite reduction yields an impure molybdenum alloy plus aluminum sulfide. The latter readily hydrolyzes, to yield pure hydrogen sulfide which can be converted to elemental sulfur by the Claus process. At least 95 percent of the molybdenum can be subsequently recovered as 99.95-percent-pure molybdic oxide.

Jan 1, 1968

By M. M. Tilman

A series of alloys was laboratory prepared by adding up to 4 weight-percent cobalt to the basic composition of type AM 350 (AISI 633) stainless steel. Aging curves were established for each alloy at 750° F, 850° F, and 950° F for lengths of time up to 100 hours. A series of annealed steels containing as much as 1 weight-percent cobalt was cold-rolled 50 percent and aged for 3 hours at 850° F. No improvement in hardness due to cobalt was observed in the steels transformed by heat treatment. Slight improvements in hardness were observed in the steels transformed by cold working.

Jan 1, 1968

By C. A. Herbert

"The Workman's Compensation Law of Indiana, enacted in 1915, amended in 1917, 1919, 1923, and 1927, and in 1929 named the Indiana Workmen's Compensation Act of 1929, provides for a weekly compensation for disability due to accidents of 55 per cent of the average weekly wage of the employee, to start on the eighth day of disability. Compensation is computed from a maximum and minimum weekly wage of $30 and $16, respectively. Thus, the maximum weekly compensation is $16.50 and the minimum $8.80; the total compensation paid is not to exceed $5,000.In addition to the compensation the employer is required to pay all medical, surgical, hospital, and nurse fees for a period of 30 days and may be required to pay such fees for an additional 30 days at the direction of the Industrial Board of Indiana. In the case of fatalities the employer must contribute $100 toward funeral expenses.The law also stipulates that ""the employer shall keep a record of all injuries, fatal or otherwise, received by his employees in the course of their employment,"" also that the employer shall report within one week of their occurrence all accidents that cause either the death of the employee or the loss of more than one day's work. However, no standard form is furnished or required by the industrial board on which the employer shall keep a record of accidents, neither is he required to report the time of return to work of the injured employee unless the period of disability exceeds seven days and the accident thus becomes compensable. Hence, no record is kept of noncompensable accidents other than the first report sent to the industrial board by the employer.If the employer were required to keep a complete and concise record of all accidents, in duplicate, on a special form either furnished or required by the board, giving all of the essential data in regard to the accidents, and if he were required to submit a copy of this record to the board at the end of the fiscal year, the data thus assembled would not only be of material assistance to the board, particularly in making up its annual report, but would also furnish information of much value in the study of accident causes and what may be done to remove them.Those industries that have made marked progress in reducing accidents keep such records, as it is only through a full knowledge of how accidents occur that intelligent steps can be taken to prevent their recurrence. Unfortunately, the mining industry as a whole in Indiana has not kept pace with many other industries in reducing accidents, and it is urged as an aid to improvement that a thorough and complete record of mining accidents be kept."

Dec 1, 1932

Research workers from the Bureau of Mines and industry met with other government and industry representatives at the Mont Chateau Lodge, Morgantown, W. Va., on May 30-31, 1973, to discuss the current status of methane control in eastern U.S. coal mines. The opening remarks, the eight technical presentations, and the discussions of the members of a government-industry panel are published here for the benefit of those concerned with the control of methane in coal mines. In addition, an introduction has been added to present the background of work in this field.

Jan 1, 1973

By Gregory M. Molinda

The Bureau of Mines conducted an investigation into the occurrence of outbursts of salt known to be responsible for explosions, fatalities, and damage in domal salt mines. The purpose of the investigation was to develop a basis for predicting these outbursts based on geologic and associated physical properties of salt. The investigation was conducted at the Cote Blanche salt mine in southern Louisiana. Because outbursts are the primary mode of methane emission into the mine, more than 80 outbursts, ranging in size from 1 to 50 ft in diameter have been mapped. These outbursts generally are aligned and elongate parallel to the direction of salt layering. More than 200 salt samples, both random and selected, were tested for methane content. It was found that outburst zones are well correlated with high methane content. Detailed mapping also revealed that the zones are well defined, with salt crystal size abruptly increasing upon entry into the zone. The intensity of folding and kinking of the salt layering within the outburst zone also appears to increase. An interbedded sand layer occurring throughout the mine does not appear to be a significant source of methane. However, fine-grained salt may be related to outburst occurrence.

Jan 1, 1988

To provide a method for locating trapped miners promptly and accurately. The Approach: Develop a wireless emergency system that is intrinsically safe, compact, easy to operate, reliable, sturdy, and economical. How It Works: A (one transmitter has been developed under Bureau of Mines contracts. The transmitter weighs only a few ounces, is powered by a cap lamp battery, arid can be carried on the miner's belt. A compact loop antenna, which could either be carried by the miner or strategically located in the mine, is used to generate a magnetic field that is sensed by a mobile receiver on the surface. When needed, the antenna is deployed to form a single loop. In mines where the overburden is less than 600 feet, a loop of No. 19 wire approximately 30 feet in circumference is normally adequate. This antenna weighs less than one half pound. In deeper mines, a heavier wire and bigger loop is required; a No. 10 wire deployed around a pillar has been used.

Jan 1, 1974

By August J. Kwitowski

This Bureau of Mines report describes how the reinforcement mechanisms of untensioned, full-column resin bolts were determined during one underground study. Both axial and transverse shear loadings were identified for two instrumented resin bolts that replaced standard resin bolts in an opera-ting room-and-pillar mining section. The strain responses of resin bolt steel cores to local axial and transverse shear loadings are described. This information was obtained from laboratory testing of resin bolts installations; it was also used to analyze the data from the underground test.

Jan 1, 1980

By J. S. Peterson, G. P. Cole

The National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Center (PRC), has conducted research to improve electrical fault detection on coal mine direct current (dc) trolley systems. Present circuit breaker protection systems are current-magnitude-based and cannot discern between normal traffic and high resistance electrical faults. Tests were conducted at cooperating mines to assist in developing a neural-network-based detection algorithm for distinguishing between electrical faults and normal operation. The Fast Fourier Transform of the trolley rectifier current signature served as baseline data for the neural network. During field tests, the algorithm performed with greater than 90% accuracy.

By Anthony Iannacchione

One of the more pressing engineering problems for deep longwall mines in the Southern Appalachian Basin is to design longwall systems that will eliminate catastrophic coal pillar failure from the working environment. The purpose of this study is to quantify the behavior of a particular size abutment pillar prone to burst or bump. Because the 24.4-111 (80-ft) square abutment study pillar is within the pillar size commonly used in this region, understanding the behavior of this pillar should aid in future efforts to design optimum mining strategies. This research has attempted to construct the pillar stress and roof-to-floor convergence profiles in order to evaluate the ultimate strength, deformation modulus, visco-elastic deformation, and violent failure characteristics of the pillar during longwall mining. This information reflects the overriding influence of the local geologic characteristics on bursts, provides the field measurements needed to verify concurrent modeling studies, and suggest some basic mechanisms associated with the coal pillar bursts discussed in this paper.

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

Determine whether the total delay time in blasting may be safely increased beyond the currently permitted 0.5 s, without igniting a methane or methane-coal dust atmosphere and determine the minimum borehole spacing to avoid misfires. Approach At present, regulations limit the delay time used in short-delay blasting to a total of 0.5 s. Many in industry and government would like to see this total delay time increased to 1 5 to permit an increase in the number of different delays available for short delay blasting and an increase in the time between delay periods. The Bureau of Mines conducted research to determine whether the total elapsed delay time for blasting coal in underground mines could be safely expanded, with resulting improvements in productivity. The research was conducted at a surface mine in St. Clairsville, Ohio. Experimental shots were conducted in several pits, each of which had a 5-foot-high coal seam (Pitts-burg No.8) in a 50-foot highwall. The coal seam and a mobile gallery provided a good simulation of an underground coal face. The Bureau also examined the relationship between borehole spacing and misfires, to check on reports over the past few years that permissible explosives frequently misfire. These reports were not well documented, but were numerous enough to warrant investigation. Misfires of permissible explosives in an underground coal mine can be very hazardous; a burning cartridge of explosive may be ejected from a borehole and ignite the gas or dust in the mine, or a misfired cartridge in the muck pile may detonate during drilling and mucking operations, causing serious injuries.

Jan 1, 1986

This chapter presents MSHA data on mine employment and active mining operations during 1986-1995. Figures 3-1 through 3-10 show, for each commodity, the location of mine operations in 1995, and employee hours and active mining operations by year during 1986-1995 for mine operators. For coal and nonmetal operators, the number of active mining operations and the number of employee hours decreased over the 10-year period. For metal operators, the number of active operations decreased, while the number of employee hours increased. For stone and sand and gravel operators, the number of active operations and the number of employee hours remained about the same. Figures 3-11 and 3-12 show that over the 10-year period, there was an increase in the proportion of hours worked by contractors in coal mining, while the overall employment decreased. For metal, nonmetal, stone, and sand and gravel combined, the proportion of contractor hours increased, with overall employment also increasing. Table 3-1 shows the distribution of hours worked during 1986-1995 by commodity and type of operation. For coal, the majority of hours worked were in underground mines. For metal, nonmetal, and stone, the largest number of hours worked were in mills and preparation plants. For sand and gravel, all work hours other than office were in surface mines. [ ]

Jan 5, 2000

Improve underground long-hole drilling efficiency and safety by developing a lightweight, easily transportable drilling pust that can be adjusted to fit a range of mine opening heights. Background Standard one-piece commercially available steel posts weigh approximately 10 pounds per foot. Transporting these posts underground and carrying them over obstacles and through small mine doors is very difficult. Because the length of a one-piece post cannot be adjusted, variations in mine opening height at the drilling site must be accommodated. This is accomplished by stacking several wooden blocks to form a base for the post, resulting in a dangerously unstable drilling setup. The only alternative to this unstable setup is to obtain a longer post. There problems can be reduced by the use of a two-piece telescoping aluminum post having a 3-foot adjustment range in 6-inch increments. The two-piece extendable post will be easy to transport and carry underground. It will fit any opening height within its adjustment range. One large wooden block is used as a base and one cap block is used at the top to bear against the mine roof. This arrangement results in a stable, rigid setup.

Jan 1, 1990

By Edward A. Mihok

This paper presents plant design and cost estimates for limestone treatment of acid mine water covering a wide range of quality and quantity conditions. The treatment process consists of limestone neutralization, aeration, solids settling, and concentration. The design criteria for the various operation functions are based on pilot plant performance, laboratory data, and established mine water treatment standards. Unit costs have been assumed and are related to general market prices and conditions. These estimates serve as preliminary indicators of what it would cost to construct and operate a mine water treatment plant.

Jan 1, 1970

By Roy T. Sorensen

This Bureau of Mines report presents the results of a study to rank technologies for extraction of alumina from bottom ash and coal shale. The available literature on composition and availability of coal waste was reviewed, and papers pertinent to alumina extraction are referenced. Types of coal waste were categorized by method of waste generation, coal content (heating value), location, coal type (ash nomenclature), and alkaline earth content. The differences and similarities among the categories of coal waste are summarized as to factors that my affect aluminum extraction, especially factors concerning chemical composition, current production, storage problems, and accumulated tonnage. Data available on physical characteristics and mineralogy did not correlate well with the individual categories of coal waste, and discussion on these two aspects is limited to the differences between coal ash and coal shale.

Jan 1, 1983

This pamphlet and the enclosed video describe a safe, effective and economical method for removing dust from work clothes. Background Information Dusty work clothes can increase a worker’s exposure to respirable dust. Respirable dust is usually considered to be particles having an aerodynamic diameter of 10 microns or less and able to enter and deposit in the gas-exchange region of the human lung. A former U.S. Bureau of Mines report documented a 10-fold increase in worker dust exposure on a number of separate occasions from dusty work clothes.* It was found that once clothes become contaminated, they are a continual dust source until cleaned. The only MSHA approved method to clean work clothes requires a HEPA-filter vacuuming system which is very time consuming and difficult to perform effectively. Therefore, most workers use a single air hose (not MSHA approved) which can elevate dust levels for the worker, co-workers, and the work environment. A substantial amount of engineering technology has been developed that, when applied, can significantly lower respirable dust exposures of workers at mineral processing plants. But even with these improvements, some workers continue to exceed their permissible exposure limit. Elevated exposures increase the potential for developing debilitating or fatal lung diseases. ?e clothes cleaning method described within is an example of a continuing effort to reduce the potential for developing these lung diseases. Information about engineering research by the former U.S. Bureau of Mines and NIOSH can be found online at www.cdc.gov/niosh. ?is website can also be used for obtaining NIOSH information about health hazards associated with crystalline silica.

By B. W. Madsen

As part of a program to maintain an adequate supply of minerals and metals to meet national economic and strategic needs, the Bureau of Mines conducted research to determine the diffusion coefficients for ferric ions in synthetic copper leach solutions. Determination of ferric ion diffusion coefficients in typical dump leach solutions is necessary for predicting leaching rates of copper from large-scale leaching operations and for optimizing concentrations of ferric iron in solutions to maximize leaching efficiency. Derivative chronopotentiometry, an electroanalytical technique, was used to determine ferric ion diffusion coefficients. The diffusion coefficient decreased dramatically with increasing concentration of iron in solution. An empirical model was used to relate the ferric ion diffusion coefficient to the total amount of sulfate in solution. Measuring the diffusion coefficient dependence on temperature yielded an activation energy of 5.5 kcal/mole of ferric ion. Activity coefficients of ferric ions as a function of concentration were calculated from diffusion coefficient data.

Jan 1, 1981

By d&apos, Kathleen J. Amico

THIS SUMMARY appears in Minerals Yearbook volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U .S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed ?mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1965

By T. O. Llewellyn

The Bureau of Mines, as part of its goal to develop technology that can conserve domestic mineral resources investigated beneficiation methods for recovering phosphate minerals from two Southern Florida deposits with high magnesium content. Chemical analyses of sized fractions indicated that no coarse pebble concentrate could be produced from either deposit. Conventional fatty acid-fuel oil batch flotation tests on two phosphate samples, analyzing 6.8 and 8.5 pct P205, yielded concentrates containing 28.97 to 29.80 pct P20S at recoveries ranging from 72.4 to 76.9 pct of the flotation feed. The MgO content ranged from 1.20 to 1.36 pct. Bubbling S02 gas through an aqueous concentrate slurry, further reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 pct, but with a concomitant loss in the phosphate recovery. Settling characteristics of slimes from both phosphate samples showed a slow settling rate, which is a typical characteristic of other slimes in the region.

Jan 1, 1981