Search Documents

By Scott A. Stebbins

During 1981, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral resource survey of the 6,400 acre (15,800 ha) Lincoln Creek RARE II area (No. 5983) in the Toiyabe National Forest (fig. 1). Samples of outcrops and stream channels contained no significant amounts of economic minerals. A radioactive deposit in a pegmatite dike occurs 1.25 mi (2.02 kin) southeast of the study area, hut similiar deposits have not been discovered within the area boundary. No coal or deposits were found.

Jan 1, 1982

By Francis Crowley

Elementary concepts of seismic wave properties are reviewed to establish a framework for discussing seismic noise and its suppression. A liberal number of references is included for those who wish to pursue the topic in detail. A base motion noise level is established for a single surface seismometer. It is argued that simple array processing and seismometer burial should regularly permit us to approach this base noise level which is found in areas free of conspicuous man-made seismic noise sources. The sensitivity of the base seismic level to a number of common disturbances is presented. Solutions that promise to hold the "effective" seismic noise at a site near the base level are given for acoustic, meteorological and fixed local surface sources. Guidelines are suggested for controlling other local man-made sources, e.g. vehicular traffic, by keeping them at sufficiently large distances away from the seismometers to keep noise at permissible levels. These guidelines are speculative and conservative. They should be the subject of future study. The ability to process against general local activity, drilling, and intra- mine sources is limited. Certainly no dramatic gain is to be expected. When strong man-made and/or intramine noise sources are not controllable, detection may well be impossible to achieve, unless the seismometer can be moved close enough to the suspected miner position, i.e. via very deep holes, to compensate for the likely vast differences in strength of the miner signal and the uncontrollable man-made noise sources. However, many intramine sources, e.g., falling water, rock bursts, explosions, etc., may well preclude the existence of a hale miner in their vicinity, and therefore any need to attempt detection of a miner at such locations. The following recommendations are made to enhance the detection and location of a miner signaling seismically. They are: 1. Seismometer burial in slim holes. 2. Narrow band detection, using multiple narrow band filters to cover the likely signal band. 3. Broadband recording and analysis for time-of-arrival estimation.

Jan 1, 1974

By Joseph E. Matta

The Bureau of Mines conducted tests using a tracer-gas technique to measure the effectiveness of the jet fan, which is often employed in mines to ventilate dead headings. Results of these tests show that jet fans can (1) ventilate dead headings beyond the maximum penetration distance indicated by smoke-tube detection of air movement, and (2) redistribute available fresh air through larger working areas. However, if the fresh air base is insufficient, the fan will merely recirculate the contaminated air and disperse it over a larger volume.

Jan 1, 1978

By Seth C. Schaefer

The Bureau of Mines studied thermodynamic properties of liquid Al-Si alloys with the high-temperature galvanic cell Al(1)//Al+3(AlC13 in NaCl?KCl)//Al-Si alloy(1). Activities of aluminum and silicon (referred to pure liquid metals) show a pronounced negative deviation from Raoult's law in liquid Al-Si alloys containing 0.9 to 35.2 atomic-percent silicon. Activity coefficients and the properties [?Gi, ?GxS ,?H, ?G, ?Gxs , and ?S] have been derived from the experimental data and are summarized in tables and illustrations.

Jan 1, 1974

1. In 2002, a total of 256 metal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Metal mines were the smallest mining sector,1 comprising 1.8% of all mining operations. • Gold mines comprised 44.1% (n = 113) of all metal mining operations. Other types of metal mines were copper ore (n = 31; 12.1%), iron ore (n = 25; 9.8%), and lead and/or zinc ore (n = 21; 8.2%). • Nevada is the state with the largest number of metal mines (n = 53; 20.7%).

Jan 1, 2004

By Thomas P. Meloy

"The presence of respirable quartz-bearing mineral par-ticles has been well documented in many coal mines, and the Mine Safety and Health Administration regulations address the quartz content of mine dusts. Unfortunately, the correlation between the quantity of respirable quartz-bearing mineral particles and the pathogenicity of the dust is not strong. Work is currently underway by the National Institute for Occupational Safety and Health/U.S. Bureau of Mines and work is being included in the Respirable Dust Center Program by Dr. Seehra to determine the surface availability of quartz in mixed composition mine dusts. However, this paper propose a possible source of surface quartz or a spe¬cial region in the coal that may contribute to the pathogenicity of selected particles in the respirable dust.Assumed in this model is the hypothesis that either the cleat surface is coated with quartz or some cytotoxic sub-stance that in the body is capable of destroying macrophage and thus inducing a fibrotic response (1) that during the frag¬mentation a reasonable proportion of the respirable size coal particles contain some of the original cleat surface and that these particles have the same order of in vivo cytotoxicity as do the quartz particles. It may be that these cleat surfaced respirable size particles are only contributory to the overall pathogenicity of the coal dust, nevertheless, there are enough of these particles to to considered as a potential source of the cytotoxic dust particles.This paper demonstrates that if the cleat surfaces are mineralized with quartz or have a pathogenic coating, then in many mines there will be enough respirable coal dust particles containing some cleat surface to cause a fibrotic reaction. To understand why some of the dust particles contain as part of their surface some of the cleat surface, consider what happens when a beer bottle is broken. While there are a large number of beer bottle fragments, many of the fragments, particularly the larger fragment sizes, will have as a fraction of their surface part of the original beer bottle surface. The model and mathematics of this problem have been worked out by Meloy.(2-4)In the homogeneous IAC model, (2-5) a fragment or par-ticle resulting from comminution is equally likely to occur anywhere in the material being broken. Therefore the probability of a particle of size x having part of the cleat surface in it, p(x), is proportional to x. Thus:"

Mar 1, 1989

By R. V. Ramani, P. M. T. White, D. Sutton

5.1 Incorporation with the Master Design Simulator Figure 1 diagrammatically illustrates the interaction between the various sub-systems that go to make up the total Master Design Simulator. As a total system, all sub-systems will be scheduled as needed by the controlling program. The data require¬ments for each will be made available either by providing common storage in core or by outputting data to external storage devices such as magnetic tape, disk, drum, etc. The incorporation of the Geology and Reserves sub-system into the total system involves the establishment of an interface through which data may be readily dissemminated in either direction. This interface will be provided by a geological data library in which all information available from the sub-system is stored and can be readily accessed by the main program and/or other sub-systems. In Figure 7, the information flow between the Geology and Reserves sub¬system and other sub-systems is shown. 5.2 Independent Function Geology and Reserves sub-system is capable of functioning as an independent unit or in direct communication with another sub¬system. This is possible by either continued use of the data library or by redirecting output to other peripheral devices separate from the total system libraries. (Figure 8).

Jan 1, 1974

By Victor E. Kral

"INTRODUCTION The Phelps Stokes iron deposit, also known as the Iron Mountain claim, was examined by G. L. Thompson, an engineer of the Bureau of Mines, in January 1943. As a result, the Division of Geophysical Exploration 3/ made a magnetorater survey of the deposit in June 1944, and the Mining Branch included it in a,project to explore Nevada iron deposits.The Bureau explored the deposit from September to November 1944 by means of 643 feet of diamond drilling and 445 feet of trenching holes were drilled, all of which penetrated more than: 100 feet of good-grade magnetite, although nearly all the ore except that found in the first hole contained an excessive amount of sulfur. Trenching was done largely over the first two holes, PS-1 and PS-2, and exposed the full width of the ore.The deposit is in Nye County, Nevada, 7.7 miles east of Gabbs. The property was discovered in 1902 was patented in 1907. There has been no production from the property and except for the Bureau's investigation,,has not been, explored since it was patented.Magnetite is the principal ore mineral; it occurs as fine-grained particles associated with sulfides and cemented with talc and calcite."

Feb 1, 1947

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

By Kevin A. Rider, Bernard J. Martin

Reaching movements are planned and subsequently executed [1] using visual and somatosensory feedbacks [2], where absence of visual feedback is known to increase endpoint variability [3]. Visual occlusion decreases the ability to make rapid online compensatory movements, which results in initial radial deviations that are highly correlated with radial dispersion at the target. Perturbations of rapid, visually-guided reaches are compensated on-line and result in endpoint dispersions poorly correlated with initial deviations, emphasizing the strong effect of visual feedback in temporally-constrained reaching tasks. In control conditions (no vibration), these uncompensated, rapid reaches serve as estimates of the individual’s intended trajectory. When ride motion is present, trajectories of rapid, visually-occluded reaches provide a measure of the natural biodynamic response of the cantilevered spine-arm-hand linkage. These intended movement trajectories and the biodynamic response (vibration feedthrough) are used to predict the effect of ride motion on the performance of rapid reaching tasks. Goals of this study are to investigate the influences of vehicle motion on human reaching and pointing, and to reveal movement strategies used in visually-occluded reaching tasks. Methods A six degree of freedom human-rated Ride Motion Simulator (RMS) was used to generate a dynamic vehicle environment. Participants performed discrete, rapid pointing tasks to targets presented on three touchpanel displays under stationary and random whole-body vibration. Reach instructions included successfully reaching identical circular targets (Ø = 0.25”) with the right index fingertip as fast as possible. Targets were presented on resistive-touch displays mounted approximately 60 cm from the participant’s nasion. The touchpanel displays were located in the forward and lateral directions at eye level, and forward at 45° of elevation. These displays measured the spatial error of the reach destination. A ten-camera VICON motion capture system recorded the upper body kinematics of the participant. Reflective markers were placed on the participant’s torso, head, and arms. Initial kinematics of the fingertip (i.e. time and magnitude peak tangential velocity) and tangential velocity at target were used to estimate the planned endpoint of the reach. Results and Discussion Ride motion resulted in increased endpoint variability compared to reaches performed in the stationary condition. Reaches to the elevated touchpanel consistently resulted in the largest variability across all motion conditions, suggesting that a vehicle occupant would not be capable of accurately activating a control in that location. Principal axes of endpoint ellipses were along and perpendicular to the direction of fingertip movements. Example graphs of endpoint variability with ellipses containing 95% of the data points are shown in Figure 1. These ellipses

Jan 6, 2006

By H. A. Tucker

This Bureau of Mines investigation was conducted to determine the appropriate quantities of rare-earth methals (REM) in the form of silicides to add to an alloy steel for the purpose of increasing toughness and ductility. The work was conducted in a vacuum induction furnace with the rare-earth additions required to deoxidize and desulfurize a simulated basic oxygen furnace (BOF) vacuum-degassed steel initially containing 0.013 to 0.016 percent sulfur. The product proved to be as good or better than the best basic electric furnace steel of the same composition made by the steel industry. Twenty-three experimental heats of 5 Ni-Cr-Mo-V steel were made, cast into 50-1b ingots, and hot-worked in a press and a rolling mill to ½ inch plates which were then heat-treated to 130/150 ksi4 yield strength. Impact and tension tests showed that the addition of 0.025 to 0.100 percent, or ½ to 2 lb per ton, respectively, of rare-earth metals when compounded with silicon were appropriate for increasing toughness and ductility. These quantities resulted in retained cerium contents between 0.014 to 0.025 percent, and increased the Charpy V-notch energy absorption and the percent reduction of area significantly as compared with base heats at the same sulfur content levels. All the test heats, including those with additions of REH of as much as 4 lb/ton, had greater Charpy V-notch energy absorption values than the base composition could have developed at the starting sulfur range of 0.013-0.016 wt pct.

Jan 1, 1968

By Joseph A. Holmes

The perpetuation of the supply of anthracite coal in Pennsylvania is a national as well as a State problem. Any investigation that shows how larger percentages of this coal may be saved in mining, without excessive cost, and without dangerous subsidence of the overlying surface ground, has a national as well as a local interest. Messrs. Conner and Griffith, who conducted the investigations described in this report largely for the city of Scranton, are consulting engineers for the Bureau of Mines for investigations similar to those they have already made in connection with their Scranton work; and this report is published by the bureau in response to numerous requests, because of the fact that the information it contains will prove useful in the general solution of similar problems in many of the country's coal fields. A study of the accompanying maps will show that the city of Scranton is underlain by 11 separate beds of coal, varying in thick- ness from 2 to 24 feet. It is estimated that before mining opera- tions were begun these beds of coal contained underneath the present city limits of Scranton 600,000,000 tons of coal. The 27 collieries operating within the city limits, working independently of each other, had excavated and removed, up to March, 1911, an aggregate of 198,000,000 cubic yards of coal and accompanying rock, or 3,000,000 cubic yards more than the total amount of material excavated and to be excavated by the United States in constructing the Panama Canal. This fact illustrates something of the magnitude of the problem that the city of Scranton, with the aid of these engineers and of a special commission or advisory board, has undertaken to solve. The excavation has included 177,000,000 tons of coal and 44,000,000 tons of rock and accompanying refuse. This leaves about 420,000,000 tons of coal still to be removed. As a result of other investigations and of experience in adjacent anthracite mines, Messrs. Conner and Griffith and the advisory board of engineers have advised that, as far as may be necessary to prevent dangerous surface subsidence, the spaces remaining beneath the city of Scranton from the excavation of the above-described material should be filled with sand and other materials by flushing or other processes. This operation is expensive, but it is believed to be not beyond the reach of what is practicable, nor in excess of the value of the coal that may be removed and the amount of damages that may result from the caving in of the surface if such a plan is not carried out. No one realizes so fully as do the authors of this report the need of additional tests and other investigations before the data now pre- sented by them can be fully accepted as sufficient for all purposes in the solution of the problem; and it is expected that at some early date a more extensive series of similar tests can be made by the Bureau of Mines under the supervision of Messrs. Conner and Griffith on a larger scale and under a greater variety of conditions. The field examinations made for the Bureau of Mines by N. H. Darton, which are described briefly in a chapter of this bulletin and will be discussed at length in a bulletin to be published later, indicate the extent and distribution of the sands, gravels, and other materials in the Scranton-Wilkes-Barre district available for flushing purposes if further tests indicate their relative merits; and it is expected that the relative merits of these different materials will soon be tested under such conditions as will furnish the desired information.

Jan 1, 1912

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

Le Système International d'Unités (SI) Equivalents of Common United States Units Length 1 ft (foot) = 0.30480 m Mass 1 lbm (pound mass) = 0.45359 kg Force 1 lb (pound) = 4.4482 N Volume Flow Rate 1 cfm = 0.00047195 m3/s Mass Flow Rate 1 lbm/min = 0.00756 kg/s Pressure (wg at 20° C) 1 inch wg (water gage) = 248.36 N/m2 1 inch wg = 248.36 Pa Power 1 hp (horsepower) = 0.74570 kW Energy 1 ft-lb = 1.3558 J Torque 1 lb-inch = 0.11298 N-m

Jan 1, 1977

By W. E. Anable

A 180° magnetic deflection residual gas analyzer mass spectrometer with a mass range of 2 to 200 amu was used to study the nature of gases evolved during arc and electron-beam melting of certain reactive and refractory metals. The partial pressure of residual gases over molten Mo, Hf, Ti, and Fe, was found to be similar: Water and hydrogen were evolved from the samples and from the furnace components, carbon dioxide and carbon monoxide resulted from deoxidation of some of the melts. Argon and acetone were residuals in the system, and methane was a decomposed organic compound from the oil diffusion pump.

Jan 1, 1969

By W. E. Miller, John Campbell, W. P. Yant, G. W. Jones

"Because of its interest in accident prevention, the U.S. Bureau of Mines cooperates with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground openings and in developing means for preventing such explosions. For several years this Bureau has been cooperating with the Edison Electric Illuminating Co. of Boston and the Boston Consolidated Gas Co. in detecting and eliminating combustibles and physiologically harmful gases in manholes in the city of Boston and adjacent territory.These Bureau of Mines investigations° have shown that combustible gases from the usual sources — leakage from gas—distributing systems and from underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas, which are termed here ""soil"" gases, also occur in manholes and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric changes affect their production and passage into the manhole space. These gases appear to be produced by bacterial and fermentation or through reactions of entrapped air in the soil. Soil usually abnormally high in carbon dioxide and low in oxygen, and contain varying amounts of methane. They are especially clangorous to men entering manholes because they lack sufficient oxygen to support life. Owing to the difficulty of constructing gastight manholes the most feasible method for eliminating soil gases from manholes is by ventilation. Consequently the Bureau of Mines initiate 4 study of natural ventilation methods for the removal of these gases from manholes and also for taking care of unforeseen accumulations of combustible gases and vapors.The following factors were considered by the Bureau to be important to the natural ventilation of manholes: (1) Relation of area of ventilation opening* to the capacity of the manholes, (2) size and shape of the manhole, (3) design of the ventilation opening (4) and velocity, and (5) weather conditions."

Jun 1, 1936

By John C. Edwards

Several experimental programs were conducted at the Pittsburgh Research Center to investigate the level of mine fire detection and alarm capability possible using state-of-the-art technology. These programs involved comparison of the response and alarm time of optical and ionization type smoke sensors to smoldering and flaming coal combustion in a smoke chamber. Coal combustion experiments conducted in the smoke chamber demonstrated that a CO concentration of 5 ppm above ambient corresponded to an optical density of 0.022m1. For the four smoke sensors for which a continuous analog signal was available, a smoke sensor alarm was defined as the average background signal plus ten times the peak-to-peak noise. This alarm criterion resulted in the association of the alarm for three of the four sensors with a smoke optical density of 0.022m-1. and 0.033m-1 for the fourth smoke sensor. The smoke sensors used in the smoke chamber studies were incorporated into large scale diesel fuel fire experiments conducted under normal ventilation conditions in the Safety Research Coal Mine (SRCM) at the Pittsburgh Research Center. These experiments showed that a diffusion mode smoke sensor alarmed earlier than a diffusion mode CO sensor; and, based upon the measurement of the optical transmission at the location of a pump mode ionization type smoke sensor that a pump mode ionization smoke sensor alarmed at an average smoke optical density of 0.021m" for the twelve experiments conducted. A series of 30 and 330 kW diesel fuel fire intensity experiments were conducted under zero airflow conditions in the SRCM. It was determined that :(I) thermal sensors are inadequate at 30 m from a 300 kW fire;(2) a diffusion mode ionization smoke sensor can be more effective for mine fire detection than a diffusion mode CO sensor;(3) recommendations can be made for sensor spacing in a mine entry based upon the measured CO buoyancy induced spread rates along the mine roof and the time for a developing coal fire to ignite a conveyor belt.

By Lloyd A. Morley, Alan M. Christman

Presented below is a review of how the objectives, as outlined in the statement of the problem, were achieved. 1. Methods of evaluating the performance of grounding systems must be described. These methods are the subject of Chapter III. 2. Field trips to operating mines should be undertaken, and a cri¬tique of their grounding systems made upon the basis of obser¬vation and the application of the above techniques. An analysis of field trip data, along with practical recommendations, is in¬cluded in Chapter IV, while a complete review of all field trips is given in Appendix I. 3. Because of their thoroughness, present coal mine regulations should be evaluated, and their applicability to open-pit environ¬ments appraised. This has been done in consultation with governmental agency, manufacturing, operating mine, and consult¬ing engineers. As stated in Chapter IV, insight gained through field observations has served to amplify and extend the base of knowledge from which the recommendations were made. 4. The results of these investigations should lead to suggested Federal standards. Such recommendations comprise Appendix II. In addition, several important factors, which are discussed in Chapter IV, were brought to light as a direct result of the field research. 5. Seasonal variations in the earth resistance of ground mats, as illustrated by Table 12, reinforce the need for periodic

Jan 1, 1976

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

By Judith A. Eisele

The possibility of improving the volatilization of gold through the formation of a metal-gold chloride vapor complex was investigated. Gold-silica mixtures, containing ferrous and nonferrous minerals and salts as additives, were treated in a laboratory tube furnace with a flow of chlorine gas at various temperatures. The addition of pyrite (FeS2) to a charge of gold-silica increased the volatility of the gold from 3, 20, and 62 percent of the total gold to 62, 93, and 100 percent at 200°, 300°, and 400° C, respectively. Chemical analyses of the condensate indicated the volatile species to be FeAuCl6.

Jan 1, 1971

By E. Aamland

Preparation of high-purity magnesium-yttrium alloys by electroreduction of Y2O3 dissolved in a YF3-LiF bath and the subsequent deposition of yttrium in a molten magnesium cathode was investigated in laboratory-scale apparatus. Parameters such as temperature, current density, and electrolyte density were studied. Electrolysis was conducted in a specially designed MgO diaphragm cell at temperatures ranging from 780° to 970° C. Alloys containing up to 55 weight-percent yttrium were prepared at cathode current efficiencies of 21 to 60 percent. Cell design and operation are described, and some of the limiting conditions pertaining to the method are discussed.

Jan 1, 1973