Search Documents

By Fun-Den Wang

A new approach for evaluating pit slope stability by the limiting equilibrium method has been developed by the Bureau of Mines. The finite element method of plane strain analysis is used to find the stress field of the pit slope structure. This stress field is then used to find the normal and shear stresses along a potential failure surface. The normal stresses are used with the Coulomb equation to calculate the shear resistance. The shear stresses are integrated to determine the total driving force. The factor of safety is evaluated from the ratio of the resisting force to the driving force along a failure surface, and is found to be affected by the elastic material properties, modulus of elasticity, and Poisson's ratio.

Jan 1, 1970

By Thomas J. Fisher, John J. Sammarco, Gary L. Mowrey, Edward F. Fries

This report (Safety File 3.0) is the fourth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing a system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meet the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2002

By John J. Henn

An evaluation is presented for an ammonium sulfate leaching process designed to extract manganese from Cuyuna, Minn., and Aroostook, Maine, deposits. In this process the manganese and iron in the ore are reduced to MnO and Fe 3 0 4 in a shaft furnace; the reduced ore is then leached with ammonium sulfate solution forming soluble manganous sulfate while leaving most of the iron undissolved. After filtration, the manganese and some impurities are precipitated from solution as carbonates which are then pelletized and calcined to form a product composed mainly of Mn3O4. The plants are designed to produce 100 tons per day of manganese contained in a product that is suitable for the production of ferromanganese. A byproduct credit, together with the extra processing cost, is included for the Cuyuna ore processing plants because Fe2O3 may be recovered for use in blast furnaces. The estimated operating costs per ton of manganese, excluding income taxes and return on investment, are: [ ] The process with or without byproduct recovery, when treating Cuyuna or Aroostook ores, is not economically competitive with ores available at $71.43 per ton of contained manganese.

Jan 1, 1968

By Wm. C. Dean

The location of trapped miners from their seismic signals will be in- accurate if we assume the P-wave propagation velocity is a constant. P- wave velocities are anything but constant in regions about mines, so some calibration is necessary to obtain more accurate seismic locations. The reference event method compares the time arrivals of signals generated by the miners with those previously recorded from a reference or calibration event in the vicinity of the miners. This method locates the miners' position relative to the calibration source. Hence, the location of the miners is absolute if the reference event position is known absolutely, usually from surveys and mine maps. Advantages resulting from the system, besides greater accuracy, are locations independent of the velocity model assumed, the same solution from the full array and from any subset of four or more seismometers in the array (three if the miners' depth is known), fewer seismometers required, and no complex computers required for analysis. VELA Uniform experience shows that the accuracy of locations of teleseismic explosions and earthquakes is improved by an order of magnitude over locations computed from average travel time curves. Each calibration event is applicable only over a limited range. We recommend a field test of the method at a mine to measure its location accuracy, the range of effectiveness for each calibration event, the number of seismometers needed, and the number of reference events required per mine. From these experiments we could decide whether the reference event method was useful and, if so, what form a practical rescue system would take.

Jan 1, 1974

By Martin Hertzberg

In this Bureau of Mines report, the optical detection of fires and explosions is considered fundamentally. The measured spectral radiances from methane-air ignitions are compared with the background irradiances from stray and ambient sources, and with the spectral sensitivites of various sensors. The comparison naturally suggests the optimum spectral ranges and signal processing logic that can uniquely characterize the ignition event. Both ultraviolet (UV) and infrared (IR) are considered. Several alternate sensing methods are proposed and discussed. The development and testing of an IR system designed for use in ignition suppression devices in mines is described.

Jan 1, 1975

By Fred N. Kissell, R. J. Bielicki

In this report the importance of diffusion in controlling the emission of methane in mines is examined. An in-situ diffusion parameter is defined and calculated for a hypothetical unfractured lump of coal in the Pittsburgh and Pocahontas No. 3 coalbeds. The values obtained are similar to those obtained with lump coal in laboratory experiments.

Jan 1, 1972

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By L. W. Brandt

Studies of liquid-vapor equilibria of gas mixtures at the Bureau of Mines Amarillo Helium Plant Laboratory require that the equilibrium cell be maintained uniformly at any desired temperature from approximately room temperature to -320° F. The temperature-control system must also tolerate a substantial heat input, in the form of warm gas flowing into the cell, without loss of control. Temperatures between the sublimation temperature of carbon dioxide (-109° F.) and the boiling point of liquid nitrogen (320° F.) are usually obtained by methods utilizing a hydrocarbon liquid bath cooled by liquid nitrogen.4/5/6/7/ Owing to the fire hazard attending such baths, a safer method of temperature control was desirable.

Jan 1, 1955

By R. Barany

The heat of formation at 298.15 ° K of muscovite was determined by solution calorimetry . The value obtained for the heat of formation from the elements was -1,421.2 ± 1.3 kcal / mole , and the value for the heat of formation from the oxides was -55.9 ± 1.3 kcal /mole .

Jan 1, 1964

By E. J. Gleim

"When permissible equipment is first placed in a gassy mine, those in charge may not realize the amount of attention and care they must give it if they intend to secure its full value as safety equipment. If permissible machines are installed as a safety measure, then they must receive regular, intelligent inspection and upkeep to forestall the development of unsafe features.Certain fundamentals have been followed in the design of this type of equipment in order to minimize the possibility of its igniting gas and dust. Hence, some knowledge of these fundamentals is essential to the inspector or official charged with the duty of ascertaining the condition of permissible machines with respect to safety. Familiarity with the constructional details of a machine is of first importance in making a thorough inspection of it. A knowledge of Schedule 2C3 which gives the requirements for practically all types of motor operated equipment receiving the United States Bureau of Mines' approval is also a requisite.There are certain special features in the construction followed by different manufacturers that can not be made clear for the purposes of inspection except by a lengthy description which would be inappropriate in this paper. There are, however, some general points that are applicable to the inspection of any machine employing trailing cable for connection to the power supply, also some that apply to any permissible storage-battery locomotive.The following list, based on the writer's experience in making field inspections, gives these general points in the form of questions which may he used as a guide by the inspector. A brief explanation is given after each question so that the reason for checking up on each point will be understood.1. Is a U. S. Bureau of Mines' approval plate attached to the machine? (Such a plate is necessary in order to establish identification as a permissible machine.)2. Is approval plate clean?(The plate should be clean so that the precautions enumerated on it are readable.)3. Is trailing cable protected by a fuse or other automatic circuit-interrupting device?(Trailing cable must have a fused trolley tap or other suitable means for short-circuit protection in case the cable is run over or splices fail. Proper fusing will minimize the possibility of fire in the cable reel.)4. If a trolley tap is used, does it contain a fuse of the proper capacity? (A piece of trolley wire or, too large a fuse may entirely defeat the purpose of fusing.)5. If a fused trolley tap is not used, how is connection made to the power supply? (The end of the trailing cable must be fitted with an insulated arrangement to minimize shock hazard when connecting the cable to the power supply.)6. Are the main fuses (or overload relays) of the correct size (or setting) for protection of the machine against overload?(Too large a fuse or too high a setting of the overload relay will permit damage to the machine by abuse through sustained overloads.)7. If the machine has a headlight, does the headlight circuit have overload and short-circuit protection?(The wiring of the headlight circuit on a machine is usually of a smaller size than that for the main circuits and therefore requires fuse protection proportionate to the size of wire.) Note: This same question may be asked relative to coal drills sometimes mounted on a machine."

Apr 1, 1932

By L. B. Berger, W. P. Yant, George W. Jones

Improper combustion of natural gas is the cause of low efficiency in heating appliances , also the liberation of carbon monoxide , an insidious and deadly gas . Carbon monoxide is produced during the incomplete combustion of any carbonaceous material , and quantities as low as 0.2 per cent may product death in a very short time . For healthy atmospheric conditions in the home , in which the occupants are continuously exposed , carbon monoxide should not be present in amount greater than 0.01 per cent , which value is taken as the safety limit in this report . The tests herein reported give the conditions which produce carbon monoxide when radiant -fire heaters burning natural gas are used . The conclusions drawn are based on tests made on one type of radiant heater only , but the general conclusions should apply to other types of radiant heaters of similar construction . The gas consumption , gas pressure , orifice pressure , size of orifice , and heater adjustments were changed so as to obtain as many different operating conditions as possible . In a general way the tests were carried out under the same conditions that the heater might be operated in the home .

Feb 1, 1923

By Frank E. Federspiel

In 1992, the Bureau of Mines conducted a mineral resource investigation of the 19,200-hectare Garfield Mountain study area in east central Idaho. The area had been proposed for Wilderness. Cretaceous-age quartzite and limestone conglomerates underlie the area's east half; thick travertine beds, as well as limestones, dolomites, sandstones, and volcanic tuffs occupy the west half. All the rocks have been faulted and folded as part of the Western Overthrust Belt. Two, enormous travertine deposits occur in the west end of the study area. The lower deposit, controlled by Faxe Kalk Inc., has at least 200 million m3 (cubic meters) of travertine resources. Most of their deposit is very bright with a high CaC03 content and a low insoluble residual percentage: thus it is suitable for use as a paper and paint filler. The upper deposit, owned by Idaho Travertine Corp., contains 100 million m3 of travertine resources; it is used for facing or dimension stone. Weathered travertine outcrops are buff to tan and locally vuggy. Bureau of Mines samples of' outcrops contained greater than 95% CaC03. Approximately 600 m3 of travertine have been quarried from the two deposits and used for facing stone. Four travertine quarries and two dozer cuts were examined. Faxe Kalk has 103 White Rock placer claims on the lower deposit; approximately one-half of the claims are within the study area. Idaho Travertine has the Limestone 1 and 2 placer claims on the upper deposit. A 4,647-m-deep oil and gas exploratory well was drilled on the east end of the study area without success.

Jan 1, 1993

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968

By Richard L. Lewis

This is a discussion of the application of the zonal harmonic series to problems involving dipole sources in the vicinity of spherical boundaries. The application of a formal zonal-harmonic series solution to directly obtain numerical results involves two distinct problems: namely, the convergence of the series solution and the accurate calculation of the special functions involved in the series solution. Some interesting techniques will be introduced which help to improve the convergence properties of the series solution.

Jan 1, 1973

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By S. P. Kinney, A. C. Fieldner, S. H. Katz

"The regrettable death of James S. Cunningham, Foreman Miner, attached to Bureau of Mines Rescue Car No. 2, while wearing a half-hour type oxygen breathing apparatus in a gasoline storage tank at Trinidad, Colorado, raised the question as to the possibility of gasoline vapors permeating the rubberized fabric of the breathing bags of such apparatus.It is known that most gases and especially certain organic vapors permeate rubber, by solution or a similar process. The rubber becomes saturated with the gas and if a concentration of gas is maintained on one side of the rubber sheet it slowly gives off gas from the other side. It of course takes some time for the gas to diffuse through the rubber and the length of time before it reaches the other side is proportional to the thickness of the rubber. The amount of gas that passes through per unit of area in unit time increases with the concentration of gas and also varies with the structure and composition of the rubber.It has been suggested that the gasoline vapor could not have penetrated into the interior of an oxygen breathing bag because the pressure is greater on the inside, but this is not true as the process of permeation by solution in the rub¬ber is affected only by the difference in the partial pressures of gasoline vapor on the inside and outside of the bag. The positive oxygen pressure on the inside can only prevent the entrance of gasoline vapor through measurable holes, and has no effect on permeation by diffusion through the rubber.A sample of gasoline was obtained from the tank in which Cunningham met his death. Examination by Dr. E. W. Dean of the Petroleum Division of the Bureau of Mines gave the following results.This shows the gasoline to be heavy and typical of the gasolines sold throughout Colorado for motor fuel A. Salvus half hour oxygen apparatus was arranged with the breathing bag only in a gas tight box in which the space was kept saturated with the vapor of this gasoline. The main part of the apparatus was outside the box. Oxygen from the apparatus was breathed by a man in the usual manner. Gas samples were taken from the box at intervals to determine the concentration of gasoline vapor, also samples of the oxygen breathed were taken from a side tube in the mouthpiece. The room temperature was 75°F. The concentration of gasoline vapor in the box at the beginning of the test was 4.3%. The man breathing from the apparatus thought he detected gasoline in his oxygen in two minutes after starting the test. Analysis of the inspired oxygen at this time showed 0.03% gasoline vapor. The same man remained on the apparatus for 18 1/2 minutes without suffering any ill effects. His place vas then taken by another man who wore the apparatus until the oxygen was exhausted without noticing more than a trace of gasoline at any time. At the end of the test the inspired oxygen contained 0.07% gasoline vapor. The total time of test was 38 minutes."

Dec 1, 1919

By W. H. Eddy

The Bureau of Mines conducted laboratory batch and continuous flotation processing tests on waste granite fines from South Carolina to determine the possibility of recovering high-quality feldspar and glass sand. Three flotation systems were used for removal of the iron-bearing biotite: Two employed an alkaline anionic-cationic circuit and the third employed an acid cationic circuit. Commercial-grade products were obtained when the remaining biotite was magnetically removed from the feldspar and quartz concentrates. Continuous flotation processing yielded a feldspar concentrate containing, in percent, 3.60 Na20, 5.60 K20, and 2.25 Ca0, with recoveries of 75.3, 66.6, and 72.6 percent, respectively. The feldspar tailing was high quality glass sand containing 98.0 percent Si02 and 0.025 percent Fe203; about 60 percent of the quartz was recovered.

Jan 1, 1972

By Kevin Connor

The mineral industry continued to be an almost negligible contributor to the country's economy as the Government continued its 1979 ban on any mineral exploitation for export; a policy initiated at the end of 1979. A national program had been underway since that time to map and inventory all mineral resources so as to permit future exploitation of mineral wealth in the beat interests of the country and its inhabitants. In March 1982, the British Sulphur Corp. Ltd., under contract to the Burundi Government and the International Bank for Reconstruction and Development (World Bank), began a feasibility study of Burundi's phosphate deposits at Matongo-Bandaga for potential commercial exploitation. The 1-year project effort was to define ore reserves, conceptually design mining operations and processing facilities, estimate capital and production cost, and develop a regional market and distribution survey. Work completed during the year comprised geological exploration and reconnaissance and 1,200 meters of core drilling. Reserves in excess of 5 million tons of ore-grade phosphate were estimated available for mining. Rare earth mineralization was associated with the primary apatite. The associated carbonatite within the rock matrix was preliminarily assessed to be of value as a raw material for the manufacture of cement. The contract effort was valued at $1.2 million? Matongo-Bandaga is located approximately 40 kilometers north of the capital city of Bujumbura and alongside one of the country's few paved roads.

Jan 1, 1984

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By David L. Moffatt

Considerable current interest is evident[l,2] in the use of transient electromagnetic methods for subsurface remote sensing. A transient method is discussed which uses a periodic video-type pulse containing a wide frequency range. A video pulse is used as an interrogating signal both for "target" identification and detection for relatively short depth (c 20 meters) applications in soil and soft rock media. If the medium is favorable, e.g., hard rock, greater depth applications appear to be feasible. The same procedures would be applicable for deep geological exploration but would require a substantial reduction in frequency and increase in target size. It should be noted that video pulse generators with 35 kv peak voltage and nanoseconds base widths are now within the state-of-the-art, thus significant power over broad spectral ranges is possible. In the design of a video pulse sounding system, 5 main problem areas can be identified; 1 ) selection of the pulse shape or spectral content of the video pulse, 2) design of a radiating structure which effectively couples such a pulse into the medium, 3) isolation of the radiating and receiving mechanisms, 4) realistically accounting for the dispersion and attentuation of the medium and the air-medium interface, and 5) interpretation or processing of the received signal waveform. Each of these problem areas will be discussed and illustrated with experimental and/or theoretical results. The Video Pulse Selection of the proper video pulse signal is dictated by 3 considerations, the maximum desired depth of penetration, the attenuation of the medium and the required resolution and size of the target. For a lossy medium, penetration and resolution are clearly at cross purposes and a compromise is necessary. The exact nature of the compromise is dictated by the application, but the spectrum of the video pulse should not contain any frequencies higher than the predicted cut-off, i.e., that frequency which is attenuated to the threshold level of the receiver. As a practical matter, it may be necessary to select 1 or 2 video pulses reasonably suited

Jan 1, 1973