Search Documents

Preventive maintenance practices are listed in the manufacturers' instruction books. In general, equipment that requires frequent and extensive preventive maintenance is generally the most costly. The manpower spent on these frequent trips to remote areas is such that it is usually better to invest in a more costly system which requires little preventive maintenance. The best preventive maintenance for the system is a good installation. 7.2 Preventive Maintenance and Inspections With any system, periodic inspection is required because of the corrosive atmosphere and adverse conditions that exist in underground mines. These inspections can spot potential trouble in the system. Repair or replacement at that time averts the possibility of losing effectiveness of all or part of the system. 7.2.1 Cables Approximately once per month all cables in the communications system should be inspected for kinking, chafing, cracking, wear, stretching, or other signs of physical abuse. Particular attention should be paid to cable glands at the entry or exit points to the various units in the system, where the cable goes around sharp corners, in the vicinity of holding cleats which may be clamping the cable too tightly causing potential damage, and across the areas where the cable is exposed to physical damage from outside sources, such as equipment or falling objects. If a cable is damaged, it should be replaced as soon as possible. It is mandatory that the ground leads and connections to carrier current phones be thoroughly inspected and maintained in good condition, since considerable hazard may exist to the operator or equipment if a ground connection is broken. 7.2.2 Pager Phones The most readily available test set to determine if a pager telephone is operating correctly is the pager phone itself. The following physical check of the system can be performed at any phone station. 7.2.2a Listen Circuit Remove the handset from its cradle and listen to determine if the circuit is functional, as indicated by the presence of noise or conversation on the line. If no noise or voice signals are present at the handset receiver, take the following corrective action: 1. Operate the handset press-to-talk switch several times. Any corrosion on the contacts of this switch may cause a receiver to be temporarily inoperative. Repeated operation may clear the condition. 2. Open the cabinet and see if the battery cables are properly connected and are making firm contact. Check the handset cable and its connections in the cabinet of the pager phone, and see if there is any evidence of a break in the cable, corroded contacts, or poor connections. 3. Remove the handset receiver earpiece by unscrewing it counterclockwise (to the left), and remove the receiver from the socket. Examine the handset cavity; in some units, a patch of cotton batting or floss is used as a barrier to reduce acoustic feedback in the handset. If the cotton patch has absorbed moisture, remove it and replace with a crumpled ball of soft rubber, stuffed just far enough into the handset so it will not touch the receiver or switch terminals. 7.2.2b Page Circuit and Talk Circuit Push the page switch, squeeze the handset press-to-talk switch, and call any other phone. Release the page switch

Jan 1, 1984

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954

By Donald A. Wilson

As part of a continuing effort to maximize metal recovery from domestic secondary resources, the Bureau of Mines investigated a process for recovering the metallic portion of scrap alkaline batteries. A pyrometallurgical method for recovering nickel and cadmium from Ni-Cd scrap batteries previously developed on a laboratory scale, was scaled up to 25-and 43-pound charges. The method employed reduction and/or decomposition in a retort using a minimum of 2.5 percent carbon as a reductant. Metallic cadmium was distilled at atmospheric pressure and a minimum of 900° C. Purity of the recovered cadmium was 99.8 percent minimum and the nickel-iron residue contained less than 0.02 percent cadmium.

Jan 1, 1981

By J. J. Forbes

The rapid increase in the quantity of coal being mined by stripping methods is one reason for the increased interest evinced by safety and other agencies in the hazards that are inherent in this Method of mining. The coal-mining laws of some States contain general provisions governing the mining of coal by open-cut methods, but none contains a complete list of specific safety regulations or laws for-the safe operation of such mines. The cool-mining laws of one State empower the head of the coal-mining inspection organization to proscribe regulations for coal-stripping operations and gave him the authority and power to enforce the rules and regulations promulgated by him.

Jan 1, 1944

By J. Douglas Causey

In 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 11,069-acres of the 12,290-acre Eldorado Wilderness Study Area (NV-050-423) in order to evaluate its identified mineral resources. The study area is located in Clark County, NV, adjacent to and northeast of the town of Nelson. There are inferred subeconomic resources on the Paul (gold, silver), Bel (gold, silver), Big Horn-Inez (silver, copper, lead, zinc) claims, and Montezuma (gold, silver, copper, lead, zinc) patented claim group in the Eldorado study area. Because of lack of exposures, tonnage and grade on these properties could not be determined. No resources were identified for the other five properties examined in the area. The southern two-thirds of the area is in the Eldorado mining district, a base- and precious-metal district which has been intensely explored for over 100 years. Nine claim groups were examined in the study area. Eight claim groups are within the Eldorado district and include the Montezuma (patented -M.S. 3966), Bel, Eldorado, VAR, SINJUN, Paul, Rusty Bit, and Big Horn-Inez. One property, the Flintstone claim group, is north of the Eldorado mining district at the north end of the study area.

Jan 1, 1988

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By Raymond M. Kacmar

This report presents the Bureau of Mines research on the hardware reliability prediction for two Bureau monitoring projects. The basic concepts of reliability predictions are introduced along with the reliability models and assumptions used for this particular evaluation. The results of the reliability predictions are for ground-fixed and naval-sheltered environments.

Jan 1, 1986

By J. J. Forbes

"The central rescue station maintained jointly by several mining com¬panies in a district, is gaining in popularity in a large number of mining districts throughout the country. A very efficient first-aid and mine rescue association, with rescue station, is in operation in 'the Globe-Miami, Arizona, district. This association, known as the ""Globe-Miami District Mine Rescue and First-Aid Association""; was organized on January 1, 1918. Due to the effective work of this organization, several incipient mine fires have been extinguished before the fire got under headway and before any severe damage was done.The mine rescue station, which is situated on the highway between the towns of Globe and Miami, Arizona, is centrally located with respect to the various mines in the district. The station was completed, and a full craw em-ployed for conducting it work on January 1, 1920.The directors and other officers of the association are selected from the mine officials whose properties are served by it. It includes seven large metal mining and metallurgical companies in the Globe-Miami district. The names of the companies, together with the number of men employed by each follows.A director is in charge of the station; he performs the executive work, and, is the managing head of all training in first aid and mine rescue. The director is assisted by three station attendants, one of whom takes the morning shift, another, the evening shift, and the third, the night shift. They exchange shifts every two weeks. As three shifts are maintained, an attendant is on duty at all times. He answers emergency calls in case of fires or accidents, assists with the first-aid and mine rescue training, the inspection of the first-aid boxes and supply bases that are located at the various mines, and attends to miscellaneous duties in connection with the operation and maintenance of the station."

Dec 1, 1920

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

7. Development of Acoustic Seal Checking System The acoustic approach was shown in Section 4 of this report to be the most promising concept for checking the seals. This section describes the development of this concept into a working hardware system to be used later in the field test program. This development effort included: (1) Theoretical analysis of the acoustic behavior in the mine using acoustic modeling- techniques. (2) Experimental determination of acoustic patterns in mine passages. (3) Refinement of the theoretical model. (4) Verification of final theoretical predictions in the quarter-scale laboratory model of a mine passage and seal. (5) Development of system specifications. (6) Development of the Acoustic Prototype Seal Checking System. 7. 1 Analysis of the Acoustic Seal Checker Concept The acoustic seal checker concept is based on a model which combines corridor acoustics and hole transmission theory. The idealized model for the mine sealing application is shown schematically in Figure 66. A high intensity acoustic- source is located in a corridor at a, position adjacent to the location to be sealed. The acoustic signal transmitted through the seal is monitored by a microphone pick-up placed on the opposite side.

Jan 1, 1973

By Thys B. Johnson

A three-dimensional dynamic programing method is presented for determining the optimal ultimate open pit limit. The method given is based on the block concept and is an extention of the two-dimensional Lerchs-Grossmann approach. The three-dimensional technique presented herein is fast and simple and may be used for an initial open pit evaluation when only limited data are available or as a more refined model when the entire deposit is well delineated. The method is illustrated by simple numerical examples and is also presented in algorithmic form. A computer program was written in Fortran IV which implements the three-dimensional algorithm and some computational aspects are discussed.

Jan 1, 1971

By Ivette E. Torres

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in their country and regional reports that comprise the five other sections of 1992 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible to complete, without the efforts of the personnel of our counterpart national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, our appreciation is expressed to the multitude of persons employed by these agencies for their contributions.

Jan 1, 1994

By R. Blickensderfer

Test equipment that simulated frictional impacts between coal-cutter bits and mineral inclusions at a coal face during operation of a continuous coal mining machine was used by the Bureau of Mines in the laboratory to study the incendivity of impacts between various rocks, metals, and hard-metal alloys in an explosive mixture of air-7 pct natural gas. Quartzitic sandstone was found to be the most incendive of several rocks tested. Limestone concretions from a coal seam, known locally as "sulfur balls," sparked furiously but were not incendive. Among the metals tested, the type of steel used in commercial coal-cutter tools was the most incendive material tested. A l7-4PH stainless steel was less incendive and appears to be the most promising high-strength steel alloy, reasonably economical, for use in coal-cutter bits. Some hard-metal alloys, primarily titanium and zirconium diboride composites, were also evaluated as possible replacements for the conventional cobalt-bonded tungsten carbide used in the tip of coal-cutter bits. The metal-bonded diborides were generally less inc endive but more brittle than the conventional tungsten carbide. Carbonitride coatings on tool bits were also tested but found to have no advantage. The source of ignition during frictional impact between metal and rock was studied. Immediately after impact, a yellow flash was observed and a smear of metal near its melting point occurred on the rock. This hotspot on the rock, rather than the yellow flash or sparks or metal fragments, was observed to be the cause of the ignition.

Jan 1, 1974

By Charles L. Kimbell

The series summarizing the prices of the major nonferrous metals on the stock exchanges of the United States and the United Kingdom has been continued this year in tables 23 and 24. Time constraints have prohibited preparation of other price information that has appeared in this study in previous years. Users are urged to consult the 1993 USBM publication Metal Prices in the United States through 1991, which gives an analysis of historical price series and trends, or the 1993 edition of Mineral Commodity Summaries for current U.S. prices on non fuel commodities, and to utilize U.S. Department of Energy sources for information on fuel material costs.

Jan 1, 1993

1. Mining to prevent and control underground acid formation should begin with education imparted through: (A) Course work at mining schools to teach prospective engineers. (B) Training of engineers presently employed in the mining industry through appropriate mining extension courses. 2. Considerable need exists to devote more attention to: (A) Hydrogeologic studies of mining areas to enhance the planning of new mines and the abatement program of existing mines. (B) Additional research to explore methods of dewatering the strata associated with mining areas. (C) Further effort to develop sealants for preventing contact between water or oxygen and the acid producing material associated with the coal seam.

Jan 1, 1970

By Jürgen F. PH. D. Brune, Alex C. Smith, Michael A. Trevits

Underground coal mine fires in the United States continue to present a significant hazard to the safety and health of mine workers. The leading causes of mine fires include flame cutting and welding operations, frictional heating and ignitions, electrical shorts, mobile equipment malfunctions, and spontaneous combustion The National Institute for Occupational Safety and Health (NIOSH) is conducting an in-depth program of research to address mine fire prevention, early and reliable fire detection and mine fire suppression and control technologies. One segment of the research portfolio is focused on remote methods for addressing coal mine fires. This research is important because remote methods represent the primary means of fighting a mine fire when conditions are too dangerous to fight the fire directly underground. Technologies under investigation include remote methods for installing ventilation control devices (mine fire seals) and remote methods for suppressing the fire using, the injection of inert gas, gas-enhanced foam and jet engine exhaust gases into the fire zone. This paper presents a summary of remote mine firefighting technologies used in the U.S. and the results of completed NIOSH research.

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By Peter J. Clarke

Afghanistan's mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan's gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan's total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country's natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan's development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By B. W. Madsen

Bureau of Mines research to recover arsenic from mining industry waste material and process streams is reported. Batch and column approaches were investigated for adsorbing arsenic from acid leach solutions and ion-exchange eluate solutions with hydrated titanium dioxide granules. A method for producing hydrated titanium dioxide granules was devised to provide material suitable for use in a packed adsorption tower. Selective adsorption of arsenic from acidic leach solutions was achieved. The loading capacity of arsenic on the granules was 14 wt-pct when synthetic solutions were used, but lower when actual leach solutions were used. Other elements in the leach solution were Zn, Cd, and In. The granules were used in an attempt to lower the arsenic content in a solution containing 0.95 g/l W and 0.027 g/l As from a process devised by the Bureau of Mines to treat Searles Lake brine. The arsenic content was lowered to less than 0.001 g/l, but unacceptable amounts of tungsten also were adsorbed by the granules. Adsorbed tungsten was partially stripped with pH 11.5 NaOH, and both tungsten and arsenic were completely stripped with 5M NaOH solution. Repeated loading and stripping of the granules had no effect on the loading capacity for arsenic.

Jan 1, 1983

To perform comprehensive economic evaluations on both existing and proposed mineral operations. Approach A comprehensive computer model was developed which is capable of evaluating the economics of an entire mineral recovery operation, including exploration, acquisition, infrastructure, mining, milling, smelting, refining, transportation, taxation, and return of and on capital. How it Works The MINSIM (MINe SIMulator) economic evaluation concept was developed by the Bureau of Mines in 1967. The initial versions used a continuous discounted cash flow rate-of-return (DCFROR) to measure the effect of changes in expected revenues and costs. Subsequent enhancements to the program have expanded and strengthened MINSIM, especially the addition of an option which determines total production cost (i.e., the commodity selling price that a mineral recovery operation would require in order to obtain a target rate of return), an expanded capacity for evaluating by-products from a mineral property, and significantly broadened taxation determining capabilities. The MINSIM computer program uses essentially the same procedures and calculations that are performed in a manual economic evaluation, although the program accomplishes its tasks much more rapidly and accurately, An experienced mineral economist may require a week to evaluate a single mining operation with the same detail and consistency provided by MINSIM in a matter of seconds of computer time.

Jan 1, 1983

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920