Search Documents

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control of anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/. These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the mounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating beers dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By N. Fragen, H. H. Stroch

"INTRODUCTION A previous paper by H. H. Storch 4 described. three processes for the production of potassium sulphate from polyhalite (K2S01.MgSO1.2CaS04.2H2o), Since these processes depended upon calcination of polyhalite followed by leaching with water at 100°C., the fundamental reactions occurring in these steps were discussed in detail. This paper, which describes processes producing syngenite (K2S04.CaSO4.H2O) and potassium sulphate and gives data concerning the production of by-product magnesia, presents the results of work performed at the Non metallic Minerals Experiment Station of the U. S. Bureau of Mines, maintained at New Brunswick, N. J., in cooperation with Rutgers University.A study of the solubility relationships of the system 5 Ca++ -Mg++ -K+-SO4 = H20 at 25ºC. shows that syngenite is stable in the presence of a concentrated MgSO4 solution, the K2SO : equilibrium concentration being comparatively low (2.6 per cent), The processes described below, which involve the conversion of calcined polyhalite to syngenite, are based on the 25°C. equilibria. It has further been found that syngenite can be decomposed by water at 100ºC, yielding a 9 to 10 per cent K250 solution, the solid phase being potassium calcium pentasulphate (K2SO, 3CaSO.H2O, hereafter referred to as ""pentasulphate""). This latter compound is unstable in the presence of water at 25°C., its decomposition resulting in a solution containing about 3 per cent of K2SO4 and a solid phase consisting of gypsum. This behaviour of syngenite with water at 100°C. and of pentasulphate with water at 25ºC. constitutes the basis of processes for the production of K2SO4 by way of the conversion of calcined polyhalite to syngenite,Syngenite is a product which may be used as a fertilizer per se. As produced in the process to be described, it contains about 50 per cent of K2SO1, and will readily give up its potash content on treatment with water, although the limiting concentration at ordinary temperatures is approximately 3 per cent. This definite but limited solubility should make this product more desirable as a fertilizer then the more concentrated forms of potash salts which have higher solubilities and hence involve the danger or plant injury due to a high local concentration of potash."

Sep 1, 1931

Many USBM research and information products are available through the systems or formats listed below: Mines FaxBack: Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone 4. After completing your selection, press the start button on your fax machine. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. CD-ROM: This USBM disk is updated quarterly and sold by GPO's Superintendent of Documents. For information on the latest product, please contact Rodger Wedgeworth, 202/501-9557. Internet/World Wide Web: Text and graphics. Access via PC-based browsing software such as Netscape or Mosaic. Universal Resource Locator (URL) is: http:/www.usbm.gav Internet/Gopher Server: Text and tables only. Using Gopher client software, access via port 70 as follows: gopher.usbm.gav Internet System Administrator: webmaster®usbm.gov (or contact your local System Administrator).

Jan 1, 1995

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By D. E. Pollock, Andrew B. Cecala

It has long been known that ventilation is a cost-effective method to lower respirable dust concentrations in all types of mining applications. The National Institute for Occupational Safety and Health has been working on a number of different research techniques that use ventilation as a critical component to lower respirable dust levels at surface and metal/nonmetal operations in the United States. This article presents five such research efforts. The first research area discusses how improving the ventilation flow patterns in an iron ore mill facility lowered respirable dust concentrations by 31 pct throughout the primary grinding area. The second research area examines how respirable dust levels were lowered at a dimensional stone shop by using air cleaning units suspended from the ceiling. A third area discusses how improvements in ventilation at underground limestone mines lowered respirable dust concentrations. The fourth area examines how improvements in dust filtration and pressurization systems significantly impacted the air quality in enclosed cabs of surface mining equipment. The last area presents a newly developed clothes cleaning technique. This technique uses an air spray manifold to blow dust from a worker’s clothing in an enclosed booth, which confines the dust for capture and removal by a baghouse dust collector. These research areas represent an array of different control technologies to lower respirable dust concentrations. Ventilation is an integral part of these control technologies.

By R. G. Gürtunca, J. A. Breslin

This paper briefly describes the progress in mine safety in the United States, with emphasis on recent events that have followed since the explosion at the Sago Mine in January 2006. Legislation following the mine accidents last year and areas of work carried out by the National Institute for Occupational Safety and Health (NIOSH) related to the accidents are discussed. American coal production in 2006 was 1,150 million short tons. Most of this coal is consumed domestically, with annual exports of coal about 50 million tons. One third of annual production is produced at surface mines and the rest from underground. This coal is produced by about 82,000 miners working at 1,400 coal mines. Major improvements in coal mine safety have been made in the US since the Federal Mine Safety and Health Act of 1977. The fatal injury rate in underground coal mines between 1977 and 2004 was reduced by 47.8% to 0.036. The annual number of fatalities dropped from 112 to 14 during that period. Likewise, the non-fatal days-lost injury rate was reduced by 42.6% from 10.87 to 6.24. The improvements in mine safety during this period can be seen in the graph of underground coal mine explosion fatalities and injuries from 1980 to present, which is shown in Figure 1. Between 1984 and 1993 (9 year period) there were 5 explosions and one major mine fire, for a total of 55 fatalities. Over the seven year period from 1993 to 1999 there were no fatalities from coal mine fires and explosions. However, in the six years since 2000 there have been 5 explosions and one fire, which have caused 37 fatalities. [ ]

By D. Randolph Berry

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller, Inc. to develop guidelines for the storage and use of Self-Contained Self-Rescuers (SCSRs) in underground non-coal mines. An SCSR is a device capable of supplying, in an emergency, one hour of self-contained oxygen (no breathing of mine air). The information and recommendations in this report were developed primarily from three sources: discussions with mine representatives (including management, labor, and government), site visits in underground mines I and a detailed analysis of every reported non-coal accident which produced d hazardous atmosphere during the 5-year period 1976-1980 -plus ten other major incidents from prior years. Volume IV has three major sections: Recommendations and Discussion (Section 2), Analysis of Mine Accidents (Appendix A), and a Summary of Discussions with Mine Representatives (Appendix B).

Jan 1, 1983

[ ]

Jan 1, 2008

By Larry G. Stolarczyk

Jan 1, 1980

By W. L. Hunter

The research on this report was conducted to obtain information on the feasibility of producing ferro chromium of varying silicon and carbon contents from domestic chromite. Concentrates from the Mouat deposit were chosen because they typify the chromite found in the Stillwater complex, the largest domestic reserve, and are similar in composition to other extensive North American and foreign deposits. Batch-smelting tests designed to produce high-, medium-, and low-carbon ferrochromium were made in single phase and three-phase, electric-arc, steelmaking furnaces. Agglomeration studies were made in a rotary kiln. Continuous smelting tests were made to yield data on the production of high-carbon ferro chromium and low-carbon ferrochromium-silicon. The carbon content of high-carbon ferrochromium was lowered to the medium-carbon range by oxygen injection. Mouat stockpile concentrates were nodulized in a gas-fired rotary kiln using quartz, limestone, and fluorspar additions in the proportion necessary to flux the slag. The nodules were smelted in a continuous test using coal, coal char, and mixtures of the two consecutively as reductants.

Jan 1, 1961

The Bureau of Mines annually publishes statistical data reflecting technological trends in the minerals industry (metals and nonmetals except fuels). This report outlines recent developments and trends and the technology outlook for mining practices and metallurgical processing based on a review of the minerals industry during the past 2 years. A historical statistical series which indicates trends in the minerals industry has been extended with 1970 data. In addition, data are given from a 5-year Bureau of Mines cyclic canvass of froth flotation plants. Data for 1970 are compared with those of 1960 and 1965.

Jan 1, 1972

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By Susanne Hering, Brent Kirby, Charles D. Litton, Tracy Allen, Kirk R. Smith, Rufus Edwards

In developing countries, high levels of particle pollution from the use of coal and biomass fuels for household cooking and heating are a major cause of ill health and premature mortality. The cost and complexity of existing monitoring equipment, combined with the need to sample many locations, make routine quantification of household particle pollution levels difficult. Recent advances in technology, however, have enabled the development of a small, portable, data-logging particle monitor modified from commercial smoke alarm technology that can meet the needs of surveys in the developing world at reasonable cost. Laboratory comparisons of a prototype particle monitor developed at the University of California at Berkeley (UCB) with gravimetric filters, a tapered element oscillating microbalance, and a TSI DustTrak to quantify the UCB particle monitor response as a function of both concentration and particle size and to examine sensor response in relation to changes in temperature, relative humidity, and elevation are presented here. UCB particle monitors showed good linearity in response to different concentrations of laboratory-generated oleic acid aerosols with a coarse (mass median diameter, 2.1 µm) and fine (mass median diameter, 0.27-0.42 µm) size distributions (average r2 = 0.997 ± 0.005). The photoelectric and ionization chamber showed a wide range of responses based on particle size and, thus, require calibration with the aerosol of interest. The ionization chamber was five times more sensitive to fine rather than coarse particles, whereas the photoelectric chamber was five times more sensitive to coarse than fine. The ratio of the response between the two sensors has the potential for mass calibration of individual data points based on estimated parameters of the size distribution. The results demonstrate the significant potential of this monitor, which will facilitate the evaluation of interventions (improved fuels, stoves, and ventilation) on indoor air pollution levels and research on the impacts of indoor particle levels on health in developing countries.

By J. R. Thoenen

Up to 1914 almost all of the world's supply of potash came from Germany and Alsace. With the cessation of shipments from Germany during the World War the importance of a domestic suppler was evident. During the past 15 years the United States has been working toward the establishment of a domestic potash industry which would end foreign dominance in this commodity. The Federal government has taken an active part in this program. As its share in the work, the Bureau of Lines has ascertained the potash resources in certain district's through core drilling and has engaged in a comprehensive program of research on the extraction of potash from its various minerals. Until the passage of the Winter bill (H. R. 496) by Congress in 1928 the Bureau of Mines had not been able to give any consideration to the western ores, wyomingite (leucite) and alunite. With the massage of this bill, however, the ray was opened for the extension of the potash studies to cover these materials.

Jan 1, 1932

By William S. Sanner

A demonstrated reserve base (DRB) of bituminous coal suitable for cokemaking has been estimated based on the latest published information on U.S. coal reserves. Bureau of Mines analyses of raw coalbed samples were used to classify the coals as low-, medium-, and high-volatile bituminous and grade them as premium, marginal, and latent coking coals. Coal rank was used as the basis for identifying coking coals, and ash and sulfur content were used to determine coking coal grade. The demonstrated reserve base of coking coal for the entire United States is 162.67 billion tons. However, only 18.96 billion tons are premium (metallurgical) grade, and between 80 and 99 percent occurs in the Eastern States. The demonstrated reserve base of marginal-grade coking coal is 31.3 billion tons; more than half the marginal reserve base is in the Eastern States, and most of the medium- and low-volatile marginal coals are in the Eastern States. The Eastern and Midwestern States contain most of the latent-grade DRB of 112.4 billion tons; most (106.6 billion tons) is high-volatile coal, and 98 percent of the medium- and low-volatile latent coals occur in the Eastern States. Based on the worst assumption, which assumes that only premium-grade coals are used for cokemaking, the DRB for high-volatile coal would suffice for 127 years, the medium-volatile coal for 80 years, and the low-volatile coal for 83 years.

Jan 1, 1979

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By Michael L. Boucher

Copper and nickel sulfides occurring in the Duluth Complex of northern Minnesota were examined at the Bureau of Mines, A microscopic study was undertaken to determine the mineralogy and paragenesis of the ore minerals. Eighty-two samples were taken from one deep diamond drill core located near Babbitt, Minn. Modal analyses are presented for the Duluth Complex rocks and for the are minerals in the major mineralized zone. The major sulfide minerals are chalcopyrite, cubanite, pyrrhotite, troilite, and pentlandite. Results of this investigation suggest that the mineralization is related to the structural features of the enclosing rocks: pores, open fractures, and cavities. The pyrrhotite-troilite-pentlandite assemblage is believed to have formed from an immiscible sulfide melt, probably associated with the troctolitic rocks. Most of it settled to the very porous base of the Duluth Complex, and to the other porous zones near xenoliths; small portions were trapped higher in the section. A later introduction of a copper-rich sulfide melt replaced some of the pyrrhotite-troilite and oxides, and filled in the remaining open spaces and fractures in the Duluth Complex and those of the adjacent footwall rock.

Jan 1, 1975

By Theodore L. Turner

This Bureau of Mines report describes calcination of kaolinitic clay in a direct-fired 2-1/2- by 24-ft rotary kiln at 750° and 775° C. Methods for preparing kaolin feed materials and characterization of calcined products are discussed. Approximately 99 pct of the alumina in a typical eastern Georgia kaolin was soluble in HC1 after calcination at either 750° or 775° C.

Jan 1, 1982

By Damon C. Gray

This report contains a recommended program of acoustic research to be conducted by the U. S. Bureau of Mines. The program is directed toward the abatement and control of machinery noise in underground coal mining operations. The study conclusions and specific problem areas which led to the definition of the recommended program are also briefly described.

Jan 1, 1971