Search Documents

By William J. Wuest

The technical analysis of parameters that can influence roof and rib reinforcement is important to the operation of safe and profitable underground mines. One such parameter, studied in this U.S. Bureau of Mines investigation, is the effect of time on untensioned, resin-grouted bolt anchorage characteristics. A group of seventy-three 4-ft-long bolts with three different grout column lengths were I installed in a stable coal mine roof. The bolts were then subjected to standardized pull tests at various intervals throughout a 37-month period. For each test, load-deformation data were reduced to determine axial stiffness and yield point. The magnitudes of these two anchorage characteristics at the time of installation were compared with results from subsequent pull tests to determine if anchorage capacity deteriorated. Bolts with 18-in grout columns were studied over 9 months, and no measurable loss occurred. Bolts with 48-and 24-in grout columns were studied over 37 months and also exhibited no measurable loss.

Jan 1, 2010

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

By Thomas L. McVay

Laboratory batch and pilot plant flotation tests were made to determine the feasibility of recovering commercial grade kyanite from a quartzite- kyanite rock from the Graves Mountain, Ga., deposit. Best results in laboratory and continuous tests were obtained using sodium carbonate for pH control, citric acid for quartz depression, and oleic acid as the kyanite collector. Over 80 percent of the kyanite was recovered in a concentrate analyzing 56.8 percent Al203 and 3.8 percent hydrochloric acid soluble Fe203. Subsequent treatment of the flotation concentrate by magnetic separation reduced the acid soluble Fe2O3 to 0.6 percent and increased the alumina content to 59.2 percent. Acid leaching of the concentrate gave a product analyzing 59.7 percent Al203 and about 0.1 percent Fe203. As a result of the beneficiation research, a commercial kyanite flotation plant was completed in September 1962 by private industry.

Jan 1, 1963

By T. J. Ballard

The Rickard mine in York County, S. C., named for the original owner, Alexander Rickard, was operated about 50 years as. No records are available of the quantity of corundum shipped. Pratt states, "Many tons were picked up from the surface and shipped." The mine was visited on August 6, 1943, by the author, accompanied by Gilbert W. Withers of Atlanta, Ga. Investigation of the property was begun by the Bureau of Mines after some initial work by the Mi-Cor Corp., a company organized by Gilbert P. Withers of Atlanta to explore the property. In conducting the Bureau program, 754 linear feet of trenches were dug, 110 feet of old drifts cleaned out and examined, and 38 feet of shaft retimbered.

Jan 1, 1948

By D. J. Bauer

A primary amine extraction system was investigated for fractionating a cerium-group, lanthanide sulfate mixture. Addition of diethylenetriaminepenta-acetic acid (DTPA) to the amine extraction system resulted in separation factors as high as 5.4 for lanthanum-cerium, 8.0 for cerium-praseodymium, 3.7 for praseodymium-neodymium, and 7.0 for neodymium-samarium. In multistage studies on a cerium-free lanthanide mixture, 96 percent of the lanthanum was recovered with a purity of 95 percent.

Jan 1, 1968

By W. W. Adams

"The third annual safety contest for plants producing sand and gravel, which was conducted in 1911 by the United States Bureau of Mines in cooperation with the National Sand and Gravel Association, registered further progress in safety as compared with the two previous annual contests. Both the accident-frequency rate and the accident-severity rate were reduced.The period covered was the calendar year 1931; sixty plants participated, and 17 States were represented by the participating companies.The contest covered accidents and man-hours worked by all men at the participating plant who were employed by the same company; and it included work up to the point of delivery of the material directly to the consumer or to an independent agency of transportation--in other words, to the point of relinquishment of control of the material by the producer.The purpose of the yearly contests for producers of sand and gravel is to aid in the promotion of safety among the employees and in the reduction of accident costs to the companies. The contests develop friendly rivalry among the various plants and among the employees of individual plant in a concerted effort to prevent accidents.Two safety trophies are awarded annually, both of which are provided by Rock Products magazine. One of the trophies is for the host safety record among plants that were in operation the contest year 100,000 or more man-hours; the other trophy is for the best among plants that were in operation lees than 100,000 man-hours. Awards and the relative standing of the various plants are based upon statistical compilation by the Bureau of Mines of accident reports and employment reports furnished by the enrolled companies. are summarized at the close of each year, and the summaries are submitted to each company concerned for certification as to the accuracy of the summary and the completeness of the company's reports from which the summary was prepared. When the summery is returned signed by an official of the company, the records are considered to be a trustworthy basis for determining the relative standing of the various plants. The position of each plant is determined by its accident-severity rate; that is, the number of days of disability resulting from accidents for each 1,000 men-hours of work done by all employees at the plant."

Aug 1, 1932

By L. M. Demers, D. C. Kuhn

It has been suggested that radicals on the surface of dust particles are key chemical factors in the pathophysiology that results from the occupational inhalation of coal and silica dust. In addition, oxygenated derivatives of arachidonic acid (eicosanoidsJ have been implicated as important biochemical mediator5 of mineral dust-induced lung disease through their role in bronchial and vascular smooth muscle reactivity, inflammation, and fibrosis. Therefore, we assessed eicosanoid production by the rat alveolar macrophage (AM) exposed in vitro to mineral dusts with varying surface chemical characteristics in order to determine if radicals associated with the mineral dust could influence the production of proinflammatory mediators in the lung environment. Primary cultures of rat AM were exposed to freshly fractured or "stale" bituminous coal dust, as well as untreated silica or silica calcined to 500 and 1100°C. Prostaglandin E1 (PGE;V, thromboxane Ai (T}(Ay, and leukotriene 84 (LTB; levels in incubation medium were determined by specific radioimmunoassay. When AM were exposed to freshly fractured coal dust, PGE2 production was markedly increased. In contrast, exposure of AM to "stale" dust significantly reduced PGE1 production. Exposure of AM to freshly fractured coal dust resulted in a significant increase in production by AM, while exposure to stale coal dust did not influence AM TXA1 production. Neither "fresh" nor "stale" coal dust had any effect on LTB4 production. In vitro exposure of AM to untreated silica resulted in a significant increase in TXA1 PGE.,, TXA; and LTB4 production compared with control. However, exposure of AM to silica calcined to 11oo•c resulted in eicosanoid levels that were not significantly different from control. These effects were still apparent 8 wk after calcination of the silica particles. Silica was a more potent activator of AM eicosanoid production than was coal, and amorphous fumed silica was a more potent activator of AM eicosanoid production than was crystalline silica. These findings suggest that radicals associated with respirable coal and silica particles may play a key role in the ability of mineral dust to activate AM eicosanoid production and therefore may be important in the pathophysiological consequences of occupational mineral dust inhalation.

Mar 1, 1992

By Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion-proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures,a multi compartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 2010

By R. Barany

The heats of formation of anhydrous ferric sulfate and anhydrous indium sulfate were determined by solution calorimetry. At 298.15° K the heats of formation from the metal, rhombic sulfur, and oxygen were -615.6 ±O.7 kcal/mole for ferric sulfate and -649.6 ±O.6 kcal/mole for indium sulfate. Heats of decomposition at 298.15° K are given for the reaction that forms metal oxide, sulfur dioxide, and oxygen) and for the reaction that forms the metal oxide and sulfur trioxide.

Jan 1, 1965

By R. W. Dalzell

The performance characteristics, efficiency, and operating pressure of jute line-brattice systems were studied under varying underground conditions; various fabric grades and installation methods were used. The test results indicate that line-brattice system efficiency is dependent upon the method of ventilation the method of installation, porosity of fabric, and size of tight rib area.

Jan 1, 1966

By E. J. Kloos

This publication lists devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, as of May 24, 1972, under provisions of Section 11.2, Part 11, Subchapter B of Chapter 1, Title 30, Code of Federal Regulations (37 F.R. 6244, March 25, 1972), for use in mines as respiratory protection in oxygen-deficient atmospheres, and in gases, vapors, dusts, fumes, and mists. Included are self-contained breathing apparatus, gas masks, and supplied-air, dust, fume, mist, and chemical-cartridge respirators. Names and addresses of manufacturers appear in the appendix.

Jan 1, 1972

By Rees D. Groves

The Bureau of Mines conducted research on reactions of copper sulfide minerals with chlorine in an aqueous system. Selected samples of covellite, chalcopyrite, chalcocite, bornite, and pyrite were leached with aqueous chlorine solutions. The mineral samples were sized on to minus 100- plus 325-mesh, individually mixed with precleaned sand and leached in an enclosed percolation column. Each mineral was leached in stages to achieve about 90 percent mineral dissolution. The chlorine leaching solutions were produced by reacting sodium hypochlorite with hydrochloric acid within the closed system. The study showed that when the mineral dissolution was complete, the reaction products (copper, iron, and sulfur) were in their highest oxidation states and a stoichiometric amount of chlorine was consumed. Although elemental sulfur formed as an intermediate product, it was oxidized to sulfate during the leach.

Jan 1, 1973

By John D. Bradley

Stibnite is 76 miles east of Cascade, Idaho, which is 78 miles due north of Boise. The altitude at Stibnite is 6,500 feet, and between Cascade and Stibnite the Forest Service road crosses two summits - Big Creek at 6,800 feet and Warm Lake at 7,300 feet. The ownership of most of the Meadow Creek group of 190 claims, which is optioned by the Bradley Mining Co from the United Mercury Mines Co. may be traced back from their consolidation by the United Mercury Co. through ownership by prospectors and small promotional companies to the discovery of the Thunder Mountain district in 1900 by the Caswell brothers.

Jan 1, 1942

By M. E. Volin

The Buckeye manganese deposits are in Stanislaus County, Calif., about 33 miles south of Tracy. From 1917 to 1919 the deposits produced 13,370 tons of ore reported to average 46 percent manganese and 14 percent silica. The deposits are confined to two areas of' development, known as the north mine workings and the south mine workings, about 700 feet apart horizontally. Mineralization occurs chiefly as rhodochrosite and psilomelane interbedded in cherts of the Franciscan formation. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a development project was started November 25, 1940, and completed June 27, 1941. The Federal Geological Survey cooperated by mapping the topography and geology and logging the drill cores. The program included road and. trail building, trenching, underground excavation, diamond drilling, and sampling. The following pages mention the location, brief the history, and note the physical .features of' the district. Mine workings are sketched, the deposit is described, and the plan of the project is noted. The work performed by the Bureau of Mines is explained in the concluding pages with a summary of the drill-hole logs.

Jan 1, 1949

By R. P. Jewett

The object of this investigation was to correlate the crushing strength of green pellets prepared from magnetite, specular and earthy hematite with the particle size of these respective raw materials. In this study no attempt was made to correlate the strength of fired pellets and particle size. The effect of particle size upon a number of fine ores and concentrates was studied. Much of the low-grade ore reserves in the Lake Superior Region must be finely ground before concentration and then agglomerated for iron and steelmaking processes. Fine natural ores also must be agglomerated. Pellets constitute an important type of agglomerate. Considerable handling occurs during screening to remove undersize and oversize pellets, and in transfering green unfired pellets from the balling machines to the heat-hardening equipment. As a result the strength of the green pellets is a factor of great importance.

Jan 1, 1961

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By John R. Benham

The Blue Joint Mtn. RARE II area may contain barite resources. One claim, the Woods Creek Barite No. 1, contains two veins of barite of drilling mud quality. The quantity of barite present could not be determined due to limited surface exposures. Sections 1, 2, 11 and 12 of T. 2 S., R. 23 W. in the study area are classified by the U.S. Geological Survey as prospectively valuable for geothermal energy resources. These sections border Blue Joint Creek Hot Springs, which are outside the study area.

Jan 1, 1981

By J. P. Hansen

The Bureau of Mines has investigated the S02 leaching of MgO from high-MgO-bearing Florida phosphate concentrates. The S02 was effective in leaching some of the MgO from three phosphate concentrates; flow rate of the S02 and leach time were major factors in determining the amount of MgO leached. Calcining the samples, then grinding to minus 200 mesh, and elevating the leach temperature gave only small increases in the amount of MgO leached. The research also showed that some of the MgO was so intimately associated with the phosphate mineral that it could not be removed by S02 leaching. This amounted to about 0.6, 0.7, and 1.0 pct MgO in three leached residues. The calculated heads for the three concentrate samples averaged 1.4, 1.1, and 1.5 pct MgO, respectively, before leaching.

Jan 1, 1985

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977