Search Documents

By G. B. Shea

In the search for possible future sources of petroleum products, the recovery and utilization of bitumens from the large outcropping deposits of bituminous sandstones in the United States have been under study by the Bureau of Mines for the past several years. The results of laboratory research in the adaptation of the hot-water separation process to recovery of bitumen from bituminous sandstones were reported in an earlier publication, on the Edna deposits near San Luis Obispo, Calif. This publication included analytical data on the cracked products and asphalts obtained from the extracted bitumen and on the cracking and distillation of the bitumen. Comparable hot-water separation tests have been run in the San Francisco, Calif., laboratory of the Bureau of Mines on quarry samples from the large deposits of bituminous sandstones near Vernal and Sunnyside, Utah. The bitumens were isolated from the extracts of the separation plant and analyzed at the Petroleum and Oil-Shale Experiment Station of the Bureau of Mines, Laramie, Wyo. Part I of this report summarizes the general characteristics of the Vernal and Sunnyside deposits and discusses the hot-water separation process as applied to those bituminous sandstones and the results obtained. The separation tests showed that these bituminous sandstones also respond to treatment by the hotwater method of separation. The bitumen in the Vernal sandstone was extracted more readily by the action of hot water than was the Edna bitumen, which greatly simplified plant operation. The Vernal sandstone contains no water-soluble iron compounds, such as were found in the Edna sandstone, and, therefore, required no preliminary water washing. Recovery of bitumen from the Vernal sandstone was about 96 percent.

Jan 1, 1952

By R. G. Meara, O&apos

The land-pebble district of Florida, wnich in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of lime) or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the washing and formerly lost supplied the feed. During October, 1927, the United States Bureau of Mines in cooperation with the University of Alabama and the Missouri School of Mines and Metallurgy began to investigate the amenability of phosphatic sands to gravity methods of concentration. The work was under the immediate supervision of B. W. Gandrud, acting supervising engineer of the Southern Experiment Station of the U. S. Bureau of Mines at Tuscaloosa, Ala., and Will H. Coghill, supervising engineer of the ore dressing section of the U. S. Bureau of Mines. More comprehensive testing followed and in the early part of 1930 some of the companies cooperated with the bureau and the above-mentioned institutions in conducting a series of tests on hydraulic classification and tabling. The results indicated that marketable concentrates could be obtained with a recovery of 25 to 45 per cent of the phosphate formerly lost. As a result two companies have introduced hydraulic classification to treat the current tailings, and one of them has substituted classifiers for the 20-mesh screens which had been unsatisfactory. Because the phosphate grains and quartz grains have nearly the same specific gravity, the use of concentrating tables by the customary methods is not applicable. The washeries included in the following report are designated as Nos. 1, 2, and 3.

Jan 1, 1931

By J. S. Browning

The purpose of this Bureau of Mines project was to develop a method for recovering kyanite and sillimanite from the present zircon-mill tailing of the Jacksonville and Starke, Fla., plants of Humphreys Gold Corp. The kyanite and sillimanite in the ore are not being exploited at present, but procedures for recovering the two minerals were worked out by the Bureau in the interest of conserving natural resources. The current zircon-mill tailing of the Starke plant contains up to 20 percent of a mixture of kyanite and sillimanite. A similar product of the Jacksonville plant contains up to 15 percent kyanite and sillimanite. The average annual production of the tailing now being stockpiled contains several thousand tons of the two minerals. Laboratory batch-flotation tests were made on the materials to determine the feasibility of flotation methods for recovering high-grade concentrates. Various reagents were employed under different conditions to determine the optimum conditions for flotation of kyanite and sillimanite and retardation of the gangue materials. The results of the preliminary flotation tests were encouraging enough to warrant more comprehensive testing of a larger sample of the ore in the laboratory pilot plant.

Jan 1, 1956

By James W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke; (b) Which coals require special and more intensive treatment in preparation than is now practiced; and (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in this county series that describes the preparation characteristics of the coals of Perry County, Ky.

Jan 1, 1956

By A. L. Engel

This report describes results of laboratory-scale experimental treatment of nine ores containing gold and silver, including samples of products of previous plant treatment, from ore deposits in California and Nevada. The samples treated were taken by engineers of the Bureau of Mines during investigations of these ore deposits. The information reported is of interest for development of the mining districts represented or in future Investigations of similar ores from other sources. The treatment methods were as simple as possible. More complicated treatments were tried when required, The applicability of the methods and their limitations in treating the ores are shown by the data in this report. The following treatment methods were employed in the experiments described: Screen analyses were made to determine distribution of values in various screened-sized portions of crushed ore, or to determine optimum size to which a particular ore should be crushed or ground to liberate values, and some-times to determine residual values in various-sized portions of treated material.

Jan 1, 1961

By W. M. Weigel

Langley is about nine miles north of Augusta, Georgia., on the Sou them :l;.ilv1ay. According to the South Carolina. Geological Survey, tr.e district is known a.s tr. Horse Creek and Town Creek sub-areas of the Aileen or Savannah River Area f the South Ciil.Z'olina Coastal Plains. The geology and origin of the clays 3l"e Jscribea in a bulletin of the South Carolina Geological Survey (Series 4, Bull, l; "A Preliminary Report on Cl.:.ws of South Carolina.-), According to this report, i.he clays are sedimentary kaolins, in the Mid.dendor! and Hamburg series of the Cretaceous Age.

Aug 1, 1922

By A. J. Kraemer

This paper on the physical and chemical properties of crude oils from California fields is one of a series of reports on the on the districts of the United States. The paper includes a short discussion of results, tabular data, and individual analyses of eight. California crudes. Analyses of other crude oils from California have been published it Reports of Investigations 2595, 2608, and 2846. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting 65 samples was facilitated by the courtesy of representatives of oil companies in California. The methods used in testing and analyzing the samples are described in detail in Bureau of Mines Bulletin 207. A discussion of the interpretation of crude-oil analyses, as made by the Bureau of Mines, is given in Bureau of Mines Report of Investigations 2806.

Jan 1, 1931

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Southern Experiment Station of the U.S. Bureau of Mines, cooperating with the University of Alabama and Alabama coal producers, has made a series of investigations of the washability of coal from commercially important bens of Alabama. The results of 13 investigations pertaining to the Mary Lee, Clark, Black Creek, Jefferson, Pratt, Corona, Carter Brookwood, Blue Creek, Thompson, and Woodstock beds have been published. 4/ This report, the fourteenth of the series, deals with run-of-mine coal from the Henry Ellen bed at the Acmar No. 5 mine of the Alabama Fuel & Iron Co.The Acmar mine is 1/2 mile west of Acmar, Saint Clair County, in the northern part of the Cahaba field. Present production at the mine is about 800 tons per day, all of which, accept the lump coal, is treated in jigs. The washability data were obtained by means of screen-sizing and float-and-sink tests. There are included, also, tests showing the extent of liberation of impurities by recrushing the coarser sizes of coal from the top bench and tests showing the flakiness in selected sizes.SAMPLING AT THE MINEThe Henry Ellen bed at Acmar consists of two benches separated by a shale parting. At the point of sampling the top bench was 6 feet 3 inches thick and contained a 1-inch and a 1 1/2-inch band of bone. The bottom bench was 5 feet thick and was separated from the top bench by 20 inches of shale. In taking the samples for the washability study the working face was squared up, and a representative 2-ton section was out from each bench. The shale parting was discarded, according to usual mining practice."

Nov 1, 1936

This paper on. the physical and chemical properties of crude oils from California fields is one of a series of reports on the oil-producing districts of the United States., The paper includes a short discussion of results, tabular data, and individual analyses of eight California crudes. Analyses of other crude oils from California have been published in Reports, of Investigations 2595,3/ 2608,4/ and 28465/. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1931

By Louis C. Brichta

The Capital Mine is one of, the more important zinc mines in Lawrence County, Mo. Owing to the urgent need for additional zinc during the war and the available facilities for the treatment of zinc-lead ores at the property, the Bureau of Mines examined the mine during July and August 1942 and selected it for further investigation by churn drilling, which was accomplished in the fall of 1943 and spring of 1944. At the conclusion of the drilling on the Capital holdings, the Greenland property, immediately south, was investigated by drilling two additional holes. Results of the investigation are presented in this report.

Jan 1, 1948

By Fremont T. Johnson

Credited with production of more than 164,000 flasks Of quicksilver from 1876 to 1944, the Oat Hill mine has ranked third in output in the United States. During World War II, when the demand for mercury was high, this property was selected for diamond drill with the purpose of increasing ore reserves so that production could be maintained or, if necessary, increased. Although the existence of marginal-grade ore (fill material) left in the stapes and possibly of virgin ore of good grade had suspected in certain parts of the Oat Hill mine, no factual information to tonnage, grade, or location was available. In close cooperation with the Federal Geological Survey, the Bureau of Mines studied old records and the few available incomplete maps. Diamond drilling began in November 1943 and was completed in December 1944. Twenty-eight holes aggregating 8,121 feet were drilled, in only parts of the promising areas disclosed by the study of the data available. Detailed data on the work done by the Bureau as well as a brief history of the property and some operating details are described in this report.

Jan 1, 1949

By G. S. Scott, G. W. Jones

"INTRODUCTION An important phase of the accident-preventing program of the Bureau Mines is the determination of the explosion hazards of various combustible gases, vapors, and liquids encountered in mining and allied industries and the development of methods of eliminating or mitigating them.Recently, isobutane has become a commercially important raw material in the production of aviation gasoline by the alkylation process. 4/ in which isoparaffins are combined with olefins to give higher molecular weight compounds of branched-chain structure.Because of the anticipated commercial importance of isobutane in industry, it has been deemed necessary to study and determine its general explosion haz¬ards. This report gives its limits of inflammability, minimum ignition temper¬atures, and the amounts of nitrogen and carbon dioxide required to render isobutane-air mixtures noninflammable."

Jun 1, 1947

By Zsuzsanna Zborovszky

Study of the energy transfer from an inductive circuit to the discharge under the conditions of the minimum discharge voltage being smaller than the source voltage. Analysis of the effect of the electrode separation speed on the duration and maximum power amplitude of the discharge. Recommendation for optimal electrode setting. Experimental data on the variation of maximum discharge power required for ignition as a function of volumetric gas content for methane-air and propane-air mixtures. Experimental determination of the ignition limit for discharges derived from a 24, 15, 10 and 6v inductive-resistive circuit in 8.3% methane-air mixture by using the PTB breakflash with Cd disc and W wires, and also with Cu disc and BeCu wires. Method for calculating ignition limits for other source voltages.

Jan 1, 1978

Background Carbon monoxide (CO) is an odorless, colorless gas that can cause illness and death by asphyxiation. Although the toxicity of CO is understood, CO exposure can occur from unrecognized sources. On April 2, 2000, a couple and their newborn infant were poisoned by CO migrating through the ground from blasting at a nearby coal strip mine into their home near Kittanning, Armstrong County, PA. They were treated at the hospital and diagnosed with CO poisoning. The infant had a carboxyhemoglobin level of 31%, the father 28%, and the mother 17%. Carboxyhemoglobin is the compound formed in the blood when CO is breathed. Persons not exposed to CO have carboxyhemoglobin levels of 0.3%-0.7%, and cigarette smokers have levels of up to 9%. Following release from the hospital, the family installed a CO detector in the basement of their home with the help of the local fire department. This Technology News briefly describes this incident to help increase awareness of the problem. It is discussed in more detail by Eltschlager et al. [2001]. Figure 1 shows the coal strip mine believed to have generated the CO. The initial suspect for the source of the CO was the furnace in the house. Only later did it become apparent that blasting at the nearby strip mine might be the culprit. A State investigation concluded that CO had migrated approximately 500ft from the blast, through the ground, and into the home. Figure 2 shows the locations and order of blasts at the mine. Initially, the mine did not plan to blast. Overburden generally consisted of weathered shale that could be dug without blasting. However, the mine decided to blast when hard sandstone that could not be dug out was encountered within 3 ft of the coal top. The blasting was intended to break up the sandstone. Blasting was done using bulk ammonium nitrate-fuel oil (ANFO) in 6.25-in holes 25-30 ft deep on a 16-ft by 16-ft pattern, with charge weights ranging from 17 to 170 lb. The closest blast to the home was 430 ft on April 17, 2000. The distance from the home to the blast area on the day when CO was first reported (March 31, 2000) was 500 ft. Twenty blasts were detonated at the mine between March 7, 2000, and April 20,2000. The blaster was careful to prevent fly rock since another home was only 150 ft away and a garage was 50 ft away. The quantity of explosive used in the blasts was sufficient to break the sandstone, but was less than would normally be used to blast overburden. The holes were typically one-third explosive and two-thirds stemming, with powder factors averaging 0.43 lb/yd3. Additionally, the muck was not immediately excavated after each blast. The heavy confinement on the explosive acted to prevent the typical release of blasting fumes into the atmosphere. Instances of CO migrating from blasts into homes have occurred before, but generally the distances involved were under 150 ft. It is believed that the blast design contributed to the confinement of CO in the ground, and discontinuities in the ground strata facilitated migration toward the residence. Upon inspection of the blast pitwall, a regular system of joints was observed. These joints are oriented roughly from the blast pit toward the house (figures 3-4).Blast-generated CO appears to have been driven into the joint system, displacing the air. When the joint system was saturated, the next succeeding blast pushed the CO into an uncased well next to the house (a high level of CO has been measured in the well shortly after a blast). From there, the CO entered the French drain system and then the basement of the house. The joints are vertical cracks through rock layers that occur on a regular spacing (figure 3). They are most common near valley slopes and are caused when valley walls converge as the stream cuts down through the rock layers. Often called hill seams, they roughly parallel the valley walls, but can curve and split, creating a pathway for gas movement (figure 5). These fractures are often encountered when underground mining proceeds close to outcrop. The system of fractures at the Kittanning blast pit was well developed and provided a path for transmission of CO both through the sandstone and up and through the overlying shales. Blasting engineers should be able to distinguish naturally occurring fractures from blast fractures and note the frequency, development, and orientation of the hill seams and their proximity to occupied houses. The limits of transmission of

May 1, 2001

By A. W. Deurbrouck

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Upshur County, W. Va. One of the 14 samples collected was of metallurgical quality as received, 6 could be sufficiently upgraded to provide acceptable products, and 7 could not be upgraded to metallurgical quality because of their high sulfur contents.

Jan 1, 1967

By L. Keith Hudson

The purpose of this study is to provide data that demonstrates that the Alcoa flash calciner design can be used for the decomposition of AlCl3?6H2O to A1203. Heat and material valance data for calcination provides data on the partial pressure of HCl in the off-gases. Experimentally determined data for the HCl partial pressure, over solutions expected in producing alumina from clay by the hydrochloric acid process, show that HCl can be absorbed from the off-gases into process solutions to effect crystallization of AlCl3?6H2O.

Jan 1, 1979

By A. D. Hahn

This report describes reconnaissance by the Federal Bureau of Mines of titanium-bearing sandstone in Kemper County, Miss. The purpose was to determine the ilmenite, rutile, and associated heavy-mineral content of black-sand-bearing Eocene deltaic formations" The investigation was part of a survey of titanium resources of the United States. Ilmenite (FeTi03), an iron-titanium oxide, is the major titanium-bearing mineral consumed in the titanium pigment industry. Rutile (Ti02), titanium oxide, is used mainly in producing welding-rod coatings and titanium metal. The fieldwork was conducted during the first half of November 1959. Seven holes, totaling 304 feet of bore, from which 64 samples of cuttings were taken, were drilled in the north-central part of the county; and two holes, totaling 172 feet of bore, from which 34 samples of cuttings were taken, were drilled in the southeastern part.

Jan 1, 1961

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

"MASSACHUSE'M'S INSTITUTE OF TECHNOLOGYBOLSAITIS, PETERMassachusetts Institute of TechnologyDepartment of Mineral Engineering77 Massachusetts AvenueCambr1dge,MA 02130(614) 253-5069ELLIOIT, JOHN F.Massachusetts Institute of TechnologyDepartment of Mineral Engineering77 Massachusetts AvenueCambridge, MA 02130(617) 253-3305RING, TERRYDepartment of Materials Science and EngineeringMassachu5etts Institute of TechnologyCambridge, MA 02130(6117) 253-4299"

Jan 1, 1988

By R. V. Ramani, C. B. Manula, A. Owili-Eger

PART 1 THE INPUT AND OUTPUT DATA AND THE MINE SCHEMATIC SHOWING THE FLOWS FROM COMPUTER SOLUTIONS FOR APPLICATION I

Jan 1, 1975