Search Documents

By E. E. Ungar

The ways in which noise is generated and radiated by chutes and screens are described and corresponding noise control concepts are discussed. The amounts of noise reduction produced by applicable noise control means are delineated and generally cost-effective means are recommended. Available noise control materials and their applications are discussed. The results of field measurements, laboratory experiments, theoretical analyses, and studies of data provided by suppliers are summarized.

Jan 1, 1975

By Donald E. Redmon

This Bureau of Mines report examines the injury experience in the quarrying industry for the years 1964-65. Twenty-eight tables for each year are presented in which disabling work injuries are summarized by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By B. W. Gandrud

In 1927 Coghill showed that there is considerable liberation of the iron oxide mineral from gangue when the Alabama red iron ores are ground to a size suitable for classification and tabling but that there is not sufficient to make possible a high extraction and a high grade of concentrate. Coghill states: High extraction and 'high grade of concentrate cannot be obtained without grinding to a size comparable with flotation or cyanide practice. If grade of concentrate be sacrificed the grinding need not be so severe. These ores slime readily during grinding, and in most instances the slimes are only slightly higher grade than the original ore. Not only do they carry a considerable percentage of the total iron in the ore, so that to reject them as tailings would result in prohibitively low extraction, but they are too fine to be amenable to ordinary methods of gravity concentration. In 1929 the Bureau of Mines published results showing that certain Alabama oolitic iron ores could be concentrated by classification and tabling after grinding, with rubber-covered rods. This selective grinding produced slimes of much higher grade than the original ore, and they were considered part of the final concentrate.

Jan 1, 1934

By R. L. Bolmer

Rapid depletion of our known mineral resources has stimulated exploration for new mineral deposit. Abandoned mines or prospects may prove to be commercial in today's economy. Often it is necessary to revaluate such properties. Some of these may be inaccessible because of caving of flooding. Many, however, remain in good condition, except that over the years the air in the workings has become depleted of oxygen. Each year the Bureau of Mines receives numerous requests for aid in entering old mines, the air in which is incapable of supporting life. Requests of many individuals who wish to examine or explore-such places with the help, of the Bureau's self-contained oxygen breathing apparatus have been denied because of the hazards involved in the use of this equipment for such purposes. The distance to be traveled in irrespirable gases may be too great for safety; under favorable conditions, a round trip of 2,000 feet from fresh air is the maximum distance that may be traveled.3/ The use of such equipment is hazardous unless a team of at least 5 men thoroughly experienced in its use is provided; and when extensive traveling from. a fresh-air base is required, a reserve team should be provided.3/ Usually, the apparatus is requested for use in exploring workings having only one surface connection, as mines having more than one opening usually are more easily ventilated;,and in some natural ventilation is sufficient or can be made so by cleaning out obstructed openings.

Jan 1, 1951

By A. R. Mumford

During the course of an investigation conducted by the fuel section of the Bureau of Mines , on a hand- fired return- tubular boiler plant , it was found that the average cost of fuel to produce 1,000 lb. of steam was $ 0.5287 . Tests conducted after some simple changes had been made in the furnaces , and in the control of the boilers , showed the previous high cost of fuel per 1,000 lb. of steam could be reduced to the reasonable figure of $0.3540 , or the equivalent of over 30 per cent saving in fuel cost .

Mar 1, 1923

By Alex U. Miller

Since its beginning, the occupation of coal mining has been considered hazardous. It is true that there are hazards inherent in mining, but it is believed that most of them, at least, can be guarded against. Moreover, many man-made hazards can be eliminated by officials and workers adopting safer practices. Notwithstanding the hazards in coal mining, the fatal accident rate in the United States has improved. During the, period from 1911, to 1941, inclusive, the fatal accident rate varied from 5.35 to 2.22 per million tons of coal. With many handicaps during the war period, 1942-45, such as the lack of experienced manpower. and the, employment of untrained men, the increased average age of workers, and the shortage of equipment and supplies, the industry s ill further reduced its accident rate, so that it ranged from 2.30 to 1.724/ deaths per millon tons of coal. During 1944, 684,000,000 tons of coal was produced with a rate of 1.91, and during 1945, 631,000,000 tons was produced with a rate of 1.724/ deaths per millon tons of coal. The accident rate for 1945 was the lowest for the industry since records have been compiled.

Jan 1, 1946

By C. W. Owings

"Coal may be and has been hauled safely at approximately the same cost with permissible2 storage-battery locomotives as with trolley, cable-reel, crab-reel, or nonpermissible storage-battery locomotives. While in general, thinking mining men readily admit the relative safety of the permissible storage-battery locomotive there are some persons who question the safety of this type; however, the greatest opposition to the widespread use of storage-battery locomotives is from those who believe them to be more expensive to operate and to be more expensive in first cost than the trolley or cable-reel locomotive. Data collected during a comprehensive study- of storage-battery and wired transmission of power in some Pennsylvania and West Virginia coal mines indicate that there is but little difference between the cost of hauling with cable-reel or with storage-battery locomotives. It would appear that if this fact were mere generally known mine operators of the more progressive type would install such equipment and avail themselves of greater safety in hauling coal.The need for greater safety in haulage in coal mines is readily understood when it is considered that during the 12 month period, July 1, 1929 to June 30, 1930, trolley or cable reel gathering locomotives caused four explosions in which 407 lives were endangered, 11 persons were injured, and 30 lives were lost. Still another disaster was averted by the vigilance of a fire boss, who discovered a stratum of gas 3 feet thick at the top of an entry into which a gathering locomotive was about to enter. Other explosions not resulting in any fatality probably have not been reported. In addition numerous fires have been caused by trolley or cable-reel locomotives, and these fires probably would have been avoided had permissible storage-battery locomotives been used."

Nov 1, 1930

By Robert R. Stein

Using an automated drill test fooure, the U.S. Bureau of Mines measured the sound power levels produced by a small, pneumatic, rotary roof drill. A series of tests was conducted to determine (1) the relative effectiveness of several drill muffling schemes and (2) the relationship between drill sound power and pneumatic power supplied to the drill. The influence of rotation rate (i.e., airflow) and feed thrust on the penetration rate of the drill was also noted.

Jan 1, 1989

By Frank E. Scott

During the past year interest in the use of hydrazine and hydrazine hydrate as a fuel has increased in the United States; For this reason it was felt to be desirable to obtain information on the explosives properties (if these materials in order that hazards inherent in their manufacture, storage, transportation, and use might be evaluated.

Jan 1, 1949

By P. G. Kovalchik

Safe electrical operation of shuttle cars depends upon maintaining the trailing cable's conductor temperature below 90° C. However, trailing cables are wound on and off reels, which changes the heat transfer characteristics of the cable-reel system. Derating factors for trailing cables are an attempt to adjust for this changing heat transfer mechanism in a practical way. The U.S. Bureau of Mines conducted research to determine acceptable derating factors for reeled mine trailing cables, using four cable-reel combinations, representative of industry usage. Cables were continuously and intermittently loaded at different duty cycles with direct currents of different magnitudes. Relationships between the average temperature rise and current load were established for each layer of each cable. Two models were constructed; one used empirical data from the continuous and intermittent load tests, and the other was based on thermodynamic theory. Results obtained from the theoretical model were compared with those from the empirical model for the rated temperature rise of the cable. Both models can be used to simulate a variety of test conditions including those that normally cannot be conducted in the laboratory. This information was used to determine acceptable derating factors for each layer of these cable-reel combinations.

Jan 1, 1994

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By Galen G. Waddell

Dilation and contraction of the rock surrounding horizontal access open-ings of a deep mine were analyzed during stope advance to determine what type of measurements, made with relatively inexpensive instrumentation, would best reflect the rock behavior. A variety of instruments, mostly mechanical extensometers, were used. Detailed descriptions are given of Down-the-hole extensometers, floating rockbolt clusters, transit surveys, and other instruments and measuring techniques. Although all of the radial-deformation-rate graphs illustrated useful rock behavior data, the most informative graphs were compiled from data procured with the radial extensometers that penetrated, to various depths, the rock around the access openings. An analysis is given of measurement data on the rock around lateral drifts and across and adjacent to the nearly vertical vein of the Star mine, Burke, Idaho. Several useful relationships were found between the rock deformation rate and the stoping process. Information was produced on the elastic state of rock around an underground opening, effectiveness of stope support, rheology of rock, zone of influence around stopes, effectiveness of rockbolts, axis of maximum strain in a plane perpendicular to the long axis of the lateral, and other phenomena. This information could be of particular value in determining location, design, and support of underground openings.

Jan 1, 1966

By John C. Edwards

The Bureau of Mines developed a mathematical model to predict the oxygen requirements for a miner evacuating a mine. The model accounts for variations in the miner's escape speed with mine airway height, and for the empirically determined expressions for the weight-specific oxygen uptake rate for upright walking, stooped walking (duck-walking), and crawling. A Fortran computer program that is user oriented was prepared based upon the model's constitutive equations. Specific instructions for utilizing the program, as well as applications to miner evacuation from a mine, are presented.

Jan 1, 1986

By D. O. Hamiltion

The ISMS program provided for the development and demonstration of equipment modifications in both conventional and continuous coal mining systems. This report describes activities during the demonstration of the conventional equipment and includes machine performance, results of data gathering, system evaluation, and recommendations for implementing improvements.

Jan 1, 1976

By J. Dean Warner

In 1984 and 1985, as part of its critical and strategic minerals studies, the Bureau of Mines investigated lode and placer tin occurrences near Rocky Mountain (Lime Peak), in east-central Alaska. The lode occurrences consist of mineralogically complex, generally fault-controlled veins, and contain an average of approximately 0.05 pct Sn, as cassiterite. Beneficiation testing of two bulk samples of the vein material produced concentrates containing 65 and 59 pct of the total tin values at grades of 0.35 and 13.9 pct, respectively. Although as much as 30 million short tons (MMst) of mineralized rock containing up to 20 MMlb Sn may be present, the grade of these occurrences is too low to be considered economic at this time. Trace amounts of cassiterite were also identified in surface samples of glacial out-wash gravels collected along North Fork Preacher Creek, which partially drains the area of tin lode deposits near Lime Peak. Low tin grades in the samples do not account for the former erosion of a large volume of lode tin mineralization from near Lime Peak; higher tin grades may be present in gravels closer to bedrock.

Jan 1, 1988

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By Daniel T. Rogers

The Bureau of Mines, in its alumina miniplant project to investigate alumina recovery from domestic, non bauxitic ores, has conducted research on the use of a hydrochloric acid leaching, gas sparging crystallization technology. An important element of this research is the efficient separation of undissolved, siliceous residue from AICI3 -bearing leach liquors by continuous, horizontal, countercurrent vacuum belt filtration. In an effort to calculate material balances quickly and to predict material balances based on different belt filtration configurations, the perfect-mixing-cells-in-series model (PMCS) for calculating material balances around belt filters was used. Because of the porous nature of the solids, the model produced erroneous material balances. Therefore a reliable model, the shrinking voids model, was developed postulating the presence of an unwashable voids liquor volume that decreases with decreasing liquor AICI3 concentration. This volume decrease postulation is equivalent to assuming that dilute liquors flow more freely, causing more voids liquor volume to become washable. Least-squares based computer programs are provided, which are useful not only in producing material balances from plant data but also in predicting balances for untested configurations using the same feed materials.

Jan 1, 1982

By W. J. Boone

Experimental determinations were made of vapor-liquid equilibria data for a helium-nitrogen-methane system. A mixture composition was chosen to approximate the crude helium to be produced Or conservation that will eventually be further refined to obtain pure helium. Although there are publications of studies of the vapor-liquid equilibria of helium-nitrogen, helium-methane, and nitrogen-methane binary systems, there is little indication of work done on the ternary system of helium-nitrogen-methane. The experimental data presented in this report supplement the information available for the binary systems. The equilibrium vapor-liquid data and equilibrium vaporization coefficients are presented in tabular form. Graphs are employed to show an extensive amount of the data.

Jan 1, 1963

By H. A. Dierks

The work and costs involved in controlling three large fires in abandoned mines in the anthracite region of Pennsylvania are presented in detail. The work was done under authority of Public Law 89-4. Three basic control techniques were successfully employed by the Bureau of Mines: (1) forming underground fire-containing barriers by systematically flushing incombustible material into mine voids, (2) excavating an isolation trench around the fire area, and (3) complete excavation of hot and burning material in the fire area. When methods 2 and 3 were used, the excavations were subsequently back- filled with incombustible material. Preliminary location of fire perimeters by the standard use of patterned 6- and 8-inch-diameter boreholes is discussed. Investigations into air-borne infrared scanning, shallow subsurface thermal anomalies, and the use of helium to trace the movement of mine air currents are covered. Although they are costly and time consuming, boreholes have proven to be the most efficient means to date of obtaining necessary subsurface fire data. Infrared scanning was ineffective in delineating fires under more than 30 feet of cover. Helium-tracing was shown to have a good potential for determining possible hazards to adjacent residential areas from traveling mine fire gases.

Jan 1, 1971