Search Documents

By Ruddle R. W.

The slags produced in copper smelting are largely composed of silica and ferrous oxide and may therefore be regarded as essentially ferrous silicates. A fair amount of information is available on the constitutions of the liquid slags used in copper smelting and, in this connection, the large volume of work being carried out on steelmaking slags should be helpful. Constitutional diagrams are available for most of the principal systems involved (SiO2-FeO; SiO2-FeO-Al2O 3; SiO2-FeO-CaO; SiO2-FeO- MgO; and SiO2-FeO-CaO-Al2O3) and these show that additions of Al2O3 and CaO reduce the freezing points of SiO2-FeO slags but that additions of MgO increase the freezing point. A certain amount of information is available on the thermodynamics of slags, but much further work on this subject is required. Modern theories of the constitution of liquid slags deny the existence of molecular compounds but consider that liquid slags are mixtures of various ions such as, Fe2+. O2- and SiO4(4-). Little appears to be known of the reactions between matte and minor constituents dissolved in the slag

Jan 1, 1953

By J. H. E. Jeffes, C. Diaz

The heat balance and chemical equilibria involved in the production of blister copper from a chalcopyrite concentrate in a single operation are examined. It appears that two stages—one oxidising and one reducing—will be required. The analysis indicates that on thermal grounds the process is possible with a dry, high-grade chalcopyrite concentrate, if oxygen enrichment to about 30 per cent is used, but that copper losses in the slag will be serious and will require a secondary recovery operation. More extensive data on the activities of copper oxide in slags are required to elucidate this point more effectively

Dec 1, 1971

By O. Dojcar

Equations for calculating the parameters of controlled blasting (burden and spacing of boreholes and weight of the bottom charge) are derived and analysed on the basis of empirical values and made more precise through incorporation of the properties of the rock being blasted and explosive applied. For the success of controlled blasting the correct choice of the blasthole diameter/charge diameter ratio is critical. This relation is defined as the coefficient of radial decoupling of the charge; it is recommended that it is chosen to be between 3 and 3.5. Analysis of smooth blasting, cushion blasting and presplitting indicates that cushion blasting is a less destructive alternative to smooth blasting, but it has a slightly higher blasthole consumption and limited possibilities of use. There are definite economic advantages to controlled blasting, especially in rock masses of low and medium strength

Dec 1, 1996

By L Zhang

The Chinese coal industry is the largest coal producer in the world. The total production in I995 was 1.28 bnt. On the way towards introducing a market economic system, this mature industry is facing major challenges. The main problems are a large surplus of manpower, shortage of current assets and capital, low productivity, high casualties and a huge deficit. This paper discusses the present situation and the future developments in the Chinese coal industry. The current policy can be stated as ‘rapidly developing the state collieries and improving the village and private mines; integrated development to achieve an economic operating scale and encouraging a diversified economy; rapidly exploiting and developing in the North west and South west; promoting productivity and efficiency; welcoming multi-sources and types of investment; setting up coal exchange markets; and the careful control of resources and the environment'.

Jan 11, 1996

By D. V. Venugopal, W. W. Gardiner

Spessartine-quartz rocks are manganiferous sedimentary rocks rich in spessartine and quartz which occur in north-central New Brunswick. They represent a recrystallised manganiferous siltstone/chert that is contained in or associated with red manganiferous siltstone (RMS) units. The spessartine-quartz rocks and RMS form part of an Ordovician volcanic and sedimentary succession within the Appalachian-Caledonian orogen which hosts numerous massive sulphides and polymetallic vein deposits. The New Brunswick spessartine-quartz rocks are spatially and temporally associated with stratiform base-metal, precious metal and hydrothermal tin-tungsten deposits. This suggests that spessartine-bearing lithologies and zones can be useful in predictive metallogeny and for the understanding of the stratigraphy and palaeographic setting of the early Palaeozoic rocks of the Appalachian-Caledonian orogen.

Jan 12, 1992

By Tuncel M. Yegulalp, Selamet G. Ergelebi

A description is given of a method of analysing modern mining systems in terms of reliability and their effects on productivity. Non-exponential distributions, such as the Weibull and lognormal distributions, for failure and equipment repair times are also considered. The resulting non-homogeneous Markov process is solved by the method of stages. A longwall mining system is analysed as an example.

Jan 4, 1993

By G. P. . RiddIer

The ninth symposium in the series 'Prospecting in areas of glaciated terrain' was organized by the Institution of Mining and Metallurgy in association with the British Geological Survey and was held in Edinburgh from 2 to 4 September, 1991. Dicussions of sessions are presented.

Jan 4, 1992

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By Williams J. A.

"Changes proposed in 1969 to modernize legislation governing the exploitation of mineral deposits in the United Kingdom serve as the basis for a discussion of what is considered to be a desirable framework for future legislative proposals.Proposals with regard to prospecting and exploration, evaluation, and acquisition and exploitation are considered, as are suggestions relating, inter alia, to aerial surveys and land restoration.It is concluded that without legislation along the lines proposed there can be no significant revival of metal mining in Britain."

Dec 30, 1971

By C R. Ferrari

Residual subsidence is generally accepted as being about 5% of the total subsidence occurring within 12 months of all mining finishing. This paper looks at five case studies from different parts of the country, in various mining settings within a depth range of 430m to 760m. From a single seam single panel working to working the eleventh seam, all are within the concealed coalfield, similar to today's mining. The monitoring of subsidence continued for many years once the mining had finished and the results obtained are at considerable variance from the accepted norm. Subsidence has been found to carry on for up to eleven years after mining has ended, within a range of 8% to 45% of total subsidence. A highly significant factor was that subsidence, as a whole, was generally much more than predicted. The residual subsidence aspect has to he viewed in this context and in order to debate the subject at length, the causes of residual subsidence have to be balanced against the apparent inability to accurately predict subsidence. The results from the case studies were similar, even though the mining settings differed considerably. Subsidence of around 10% to 20% continued for several years after mining had ceased.

Jan 7, 1997

By L. J. Barnes, R. O. Koch, J. H. Versteegh, C. J. N. Buisman, P. J. H. Scheeren

Several water treatment options have been studied and piloted. A process based on activity of sulphate reducing bacteria combines sulphate removal and heavy metal removal in one process step. The anaerobic bacteria reduce the sulphate to sulphide and consequently metal sulphides will precipitate. The final design for the commercial scale plant is described.

Jan 12, 1992

By G. J. Lyman

Mayer curves are used for process calculation in coal preparation. They can also be used to smooth washability data by fitting a hyperbola of particular properties to ash and yield, but to introduce the density variable an independent relationship with ash content must be adopted. When this ash-density relationship has a realistic form at low density, the implied form of the mass distribution function is unrealistic, suggesting that Mayer curves represented by a hyperbolic functional form are unsuited to coal washery calculations for low-density separations. Their use at higher densities is also uncertain. A similar conclusion can be anticipated when Mayer curves are used for other mineral systems.

Jan 8, 1992

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

By J. H. Chesters

The main, though rarely mentioned advantage, is likely to be the standardisation of best practice and product. In a batch process conditions vary cyclically, but with a continuous process they would, at least ideally, remain the same for long periods of time. The other main advantages of continuous over batch processes are likely to be reduced operating and capital costs, the improved possibilities for automatic control, and more consistent product quality. Recent developments are surveyed for ironmaking and steelmaking with reference to blast furnaces; solid-product and molten-product direct reduction; the trough-type processes of Thring, Worner, the Japanese National Research Institute for Metals and Glinkov; basic-oxygen furnace (LD) variants; spray steelmaking; continuous casting and vacuum degassing; rolling; and coating. Encouragement in the devleopment of continuous processes may be drawn from the way unexpected difficulties, such as trouble with sulphur and refractories, were tackled and overcome to achieve the float glass process

Dec 1, 1971

1994 estimates for Porgera are probable and proven reserves of 58 200 000 t of ore grading 5 g/t Au. Gold mineralisation is related to an intrusive complex emplaced at shallow levels in poorly consolidated sedimentary rocks. The complex is located in a zone of fold-and-thrust deformation, whose formation may have been initiated shortly before emplacement and continues locally today. Abundant primary magnetite in the complex gives an intense, 5 km wide aeromagnetic anomaly. The deposit formed during two main stages of mineralisation, the first related to early magmatic-hydrothermal activity and the second representing later epithermal overprinting centred on the Roamane fault. Hydrothermal alteration followed closely on emplacement indicating a close genetic relationship between magmatism and mineralisation. Both stages of hydrothermal activity post-date and overprint early propylitic alteration. Several factors have acted in unison or sequentially to concentrate metals at the deposit, including an extensional or trans-tensional tectonic setting within an arc or collisional environment, the exsolution of a magmatic hydrothermal fluid prior to sulphur saturation in the melt, the development of the hydrothermal system into one favourable for transporting gold, the action of late-stage faulting in focusing epithermal fluid flow, and the role of dissolved gases in promoting fluid phase separation and high-grade ore deposition

Jun 19, 1905

Discussion at the North of England Institute of Mining and Mechanical Engineers' general meeting held in Newcastle-upon-Tyne, 8th April 1916, on the paper published in Trans. I.Min.E., vol.LI, 1916, p.72-90, included written contributions on size and gauge standardisation by Lupton A., Peck W.R., Dean S., Mayer R.W. and Ashworth J., with the author's written response, and by Bulman H.F. and Brown M.

Dec 1, 1916

By R. J. Howarth, P. L. Llowenstein

The errors resulting from field sampling, sample preparation and analysis are investigated for drainage sediments derived from homogeneous sandstone, shale, limestone, basic igneous and granite lithologies as a background to a primary reconnaissance survey of England and Wales. Emission spectrographic analyses of approximately 350 samples for Al, Ca, Fe, K, Si, Ba, Co, Cr, Cu, Ga, Li, Mn, Ni, Pb, Sc, Sn, Sr and V and atomic absorption analyses for Cu, Ni, Mn, Co, Zn and Pb have been treated statistically. For routine broad-scale surveys analysis of the unground -80-mesh sediment fraction proves satisfactory. Sampling error between localities in a stream is shown to be less than spectrographic analytical error for many of the elements considered here, except where mineralisation (contamination) occurs, but exceeds the atomic absorption analytical errors in most cases. Unless it it critical to reduce the amount of between-site variability (having regard to analytical errors) in the regional survey, there appears to be no advantage in the use of a more sophisticated sampling technique. The utility of moving-average maps in reducing the width of the confidence belt around the regional 'geochemical surface', and thus compensating to some extent for the sampling errors, is also demonstrated.

Dec 1, 1971

By W. Petruk, M. J. Matos

An aplite ore from Guarda in northern Portugal, containing albite, microcline and quartz and muscovite gangue was studied to identify conditions for extracting the feldspar minerals. The large amounts of quantitative mineralogical data needed to evaluate grinding behaviour were provided by automated image analysis. The images were acquired on polished surfaces by measuring back-scattered electron signals produced with a microprobe. Minerals were identified from X-ray spectra and discriminated by grey level and element-characteristic X-rays. The quantities and size distributions of the minerals were determined by measuring thin sections of unbroken ore to predict the grind required to liberate the feldspars. The ore was then ground to -1.7 mm, polished sections were prepared from sieved fractions and the quantities of mineral species and apparent total liberation were determined by analysis. The predicted and measured liberations were compared and the grinding behaviour of the ore interpreted. In an appended correction, the correct version of Equation 1 is represented and Tables 3 and 6 are revised to consider all size fractions, including those coarser than 300 micrometres, in calculating the total liberation from King's fractional liberation

Jun 18, 1905

By W. H. McAllister

The paper considers the geology and the coalfields that comprise the Scottish south area. It traces the history of known sources of spontaneous combustion and indicates the collieries concerned, with the position of the seams in the geological series where heatings have occurred. The methods of work over the years are described. It relates in detail the circumstances surrounding a fire at Bilston Glen Colliery in the Lothian Coalfield, and the heating at Killoch Colliery in the Ayrshire Coalfield, and the steps taken to deal with them. It also describes some of the difficulties in steep seam working. Methods adopted to prevent spontaneous combustion throughout the area are discussed, and some detail of the UNOR gas analyser is given. Finally, it comments on the present techniques in use in the area, particularly at Bilston Glen Colliery, to prevent spontaneous combustion.

May 23, 1905

By P. C. Kapur

Several empirical and semi-empirical laws of comminution, which describe the relationships between the cumulative grinding energy input and the degree of size reduction of brittle solids, have been rationally derived in the time-domain in a unified manner, starting with an integro-differential equation of grinding kinetics. The analysis leads to and provides explicit interrelationships between the energy-size reduction laws associated with Kick, Rittinger, Holmes, Bond, Charles and others, and gives useful estimates of their relative merits and validity. It is shown that Holmes' expression is, in fact, a solution to the grinding equation; consequently, this classical law is compatible with the modern theory of comminution based on population balance on particulate species

Dec 1, 1971