Search Documents

By R. C. Dunne

As ore grades of existing and new ore deposits continue to decrease there is ever increasing pressure to decrease operating costs to maintain profitabitabitiy at existing mine sites and for new projects. The accepted solution to this dilemma in most cases is to increase treatment rate, leading to a coarser grind, at the expense of marginal decreases in recovery. The recovery loss is usually associated with losses of liberated and composite coarse material. This paper will review the practice of coarse particle flotation, including the reagent chemistry, cell hydrodynamics, froth stability, entrainment and flotation cell design, all parameters important to the recovery of coarse liberated and composite particles. This will provide a better understanding of opportunities to improve the recovery of coarse particles. Some examples will be provided.

Sep 1, 2012

By Chuanyao Sun, Zhenguo Song, Aijun Ren

"Lead-Zinc sulfide ore containing carbon is one of typical refractory resource. Because organic carbon has natural floatability, it has a great negative influence on flotation of lead-zinc sulfide ores. It is difficult to obtain qualified lead concentrate by flotation using conventional reagent system. In order to reduce the influence of organic carbon on lead and zinc flotation, two alternatives, i.e., removal carbon by pre-flotation or adding carbon depressant in lead and zinc flotation, can be adopted. If the flowsheet of removal carbon by pre-flotation is adopted, the lead and zinc recovery which are lost in the carbon tailings is often higher. If conventional carbon depressants are used in lead and zinc flotation, it has a certain depression effect on lead minerals. In the paper, the ore grading 1.49% Pb, 5.73% Zn, and organic carbon 3.14% has been carried out by flotation tests. In the bulk flotation of carbon and lead minerals, Pb concentrate is only about grading 21.00% Pb. In the pre-flotation of organic carbon, it’s hard to remove most of carbon, and the loss of Pb and Zinc recovery is too much in carbon tailings. New carbon depressant BK547 and three conventional carbon depressants including sodium lignosulphonate, Fe-Cr-lignosulfonate, and dextrin, are used in comparative tests of Pb flotation, and results show that BK547 have a good depression on organic carbon, and have almost no effect on Pb flotation. Using BK547 as carbon depressant, cycle test in flowsheet of two-stage Pb and Zn selective flotation and coarse concentrate regrinding have been carried out, and results show that concentrates grading 62.51% Pb and 41.33% Zn are obtained at recoveries of 70.24% Zn and 83.58% Zn.INTRODUCTION Lead and zinc mineral resources are still the main source of lead and zinc metal. For lead-zinc sulphide ore, lead concentrate and zinc concentrate are obtained by flotation. Minerals separation by flotation is a complex process and is dependent, along with other factors, on the relative distribution of hydrophobic (e.g. collector, polysulfide, elemental sulfide) and hydrophilic (e.g. metal hydroxide) species between different particles of the same mineral phase and between mineral phases (Piantadosi & Smart, 2002; Boulton, Fornasiero & Ralston, 2003). Organic carbon has natural floatability and is often associated with lead-zinc sulphide ores. If the content of organic carbon in the ore is more, the flotation index will become worse. The main problem is that the concentrates has too low grade to be qualified grade products for sale. At the same time, the consumption of reagents is more than ordinary ores without organic carbon. In order to solve the influence of organic carbon on the flotation of lead and zinc and other sulphide ores, a lot of research works have been carried out."

Jan 1, 2018

Compressive crushing is applied in crushing plants used in mineral, mining, and aggregate in-dustry for fragmentation of rock materials. From a global perspective, the total volume of crushed rock is massive and corresponds to several billion tons. All societies have to fulfil a daily need of rock material products and its derivatives such as metals and minerals. The business for metals and minerals is global while the aggregates production is mainly a local industry. This paper presents a broader overview of optimisation with respect to product yield, use of natural resources and energy consumption. High level plant optimisation of compressive crushing plants is covered as well as real-time optimisation and optimisation of single production units. Each of three optimisation areas are presented and a discussion around how these three areas will be able to communicate with each other is given. Several models, e.g. process performance behav-iour with respect to wear, as well as fitness functions can be common for all three areas. Well-defined and representative fitness functions are of the utmost importance in order to assure that the optimisation results reflect the production targets. It is concluded that great benefits can be achieved by linking together different areas of optimisa-tion. The future for compressing crushing lies, without a doubt, in tailored processes both with re-spect to machines optimised for each customer, plant parameters and operation routines as well as an on-line adjustment, which takes into account current information and control possibilities.

Jan 1, 2014

By V. Beskrovnaya

Oxidised lead-bearing ores of one of the deposits of Russian Federation represent complex raw materials. Its main components are lead (3.2%~4.7%), silver (100~300 g/t) and zinc (0.7%~0.8%). The sample is characterized as oxidized ore. Silicium (37.4%) and iron (33.2%) are its main com-ponents and present in oxide form. Lead presents as cerussite, anglesite and plumbojarosite have a subject role. Zinc occurs as smithsonite. Certain part of zinc is associated with manganese minerals (psylomelane-pyrolusite). Close association of valuables with manganese-iron mineralization is ob-served. Silver is present in native finely dispersed form. Three options of flowsheets have been developed to recover valuables from the ore. 1. Hydrometallurgical flowsheet of lead and silver recovery on the basis of chloride leaching. 2. Flotation. 3. Flotation -flotation tailings cyanidation. Hydrometallurgical flowsheet of ore processing on the basis of chloride leaching (option I) al-lows to achieve recovery into saleable products of 68.8% Pb and 70.2% Ag. High quality lead concentrate with 71.7% lead and 700 g/t silver was obtained during flotation (option 2). Flotation tailings cyanidation (option 3) provides 24% silver additional recovery (from the ore). Technical and economical evaluation demonstrated that ore flotation (option 2) and flotation with subsequent flotation tailings cyanidation (option 3) are the most cost-efficient. Option II is the most cost-efficient variant of 1 tonne of ore processing (9.05 US dollars).

Jan 1, 2014

By Anand Anupam

Conventionally, beneficiation in Indian coal washeries is done using dense medium cyclones upto the size of 0.5 mm. Coal fines below 0.5 mm size are extensively cleaned by froth flotation. There are many problems associated with flotation of Indian coals, e.g. poor response of coal particles to flotation, misplacement of fine high-ash material to froth, loss of good quality coarser coals (within ?0.5 mm size range) to tailing streams, high cost of reagents, water contamination, etc. In addition, sophisticated control systems for efficient management of the fines washing circuits are needed. Thus, there is an escalation in the capital and processing costs. In view of these facts, studies were carried out to establish the cleaning potential of dense medium cyclones for beneficiation of fine coal down to a size of 0.1 mm, essentially aimed at reducing the load on fine coal circuits mainly comprising of flotation. ROM Coal (in the size range of -2 + 0.1 mm) obtained from JogtaOCM,Jharia coalfield possessing relatively low ash (about 21%) was used in this study. Purpose for using low ash coal was to further lower, its ash content down to 8% which is comparable, to the ash content of imported coal. After characterization studies, nine tests were carried out on the prepared feed sample for its beneficiation using a dense medium cyclone of non-conventional design (very low cone angle and longer barrel), by varying its apex and vortex finder diameters. The efficiency of separation has been evaluated using Tromp curves. It could be established that it is possible to produce a clean coal of 8% ash, with Ep value of 0.044, using Jogta OCM coal by treating it in a modified dense medium cyclone. These results are summarized and discussed in detail in the present paper. Keywords: dense medium, cyclone, fine coal, beneficiation, Jharia coal

Sep 1, 2012

By Jaeheon Lee, Jae-Chun Lee, Doyun Shin, Minseuk Kim, Hyunsik Park

"The appropriate treatment of cyanide waste water is becoming an emerging issue because of the toxic residue and large quantity produced from gold processing plants. In the present article, we designed and operated a continuous biological cyanide treatment system using domestic sewage sludge and various microorganisms including a cyanide-producing and degrading bacterium, Chromobacterium violaceum. The synthetic wastewater containing 50 mg/L of cyanide was pumped continuously into the reactor at a flow rate of 500 mL/d for 21 days. When 50 mg/L of cyanide was fed, the cyanide concentration in the effluent of the reactor inoculated with activated sludge (S-50) decreased by 7.5 mg/L in the effluent. The other reactors did not show significant cyanide degradation and the reactor inoculated with C. violaceum showed increased cyanide concentration in the effluent. The microbial community in the reactors was analyzed by 16S rRNA-gene based pyrosequencing technique to investigate microbial response to cyanide addition and operation time. The microbial community analysis shows that the phylum Proteobacteria was detected in the reactors showing significant cyanide degradation (S-50), while Firmicutes and Bacteroidetes was dominant in the other reactors with very low cyanide degradation. Proteobacteria could not compete when the other phyla Firmicutes or Bacteroidetes were inoculated. This study shows the feasibility of the biological cyanide treatment system for gold processing plants and contributes new fundamental knowledge about the microbial community in the biological cyanide treatment system. INTRODUCTION Cyanidation has been widely used to recover gold from ores or secondary resources since first proposed by MacArthur and Forrest in 1888 (MacArthur et al., 1888) and it is used in many states of the USA, including Nevada, Arizona, California, Colorado, and Idaho (Laitos, 2012). Cyanide compounds are highly toxic and create serious problems for wildlife and water management (Solomonson, 1981; Donato et al., 2007). Furthermore, because many countries have imposed strict standards for cyanide discharge (USEPA, 1985), it is essential to develop a cost-effective and environmentally friendly technology for treating cyanide-containing wastewater."

Jan 1, 2018

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By A. Pandey

Over the years, Coal Beneficiation at Tata Steel - West Bokaro has seen varied changes. With increasing R.O.M throughputs & lowering of the concentrate ash, Fine Coal Beneficiation process has thrown up myriad challenges. Development of Synthetic Collector was initiated couple of years back with Technical assistance from NLC Nalco India Ltd. Coal from West Bokaro unit was sent to Nalco?s Naperville (US) research lab for developing Tailor made synthetic collector . After comprehensive lab flotation studies, synthetic collector was developed & recommended for plant evaluation. The lab scale results were very promising in terms of improved separation efficiency & yield at similar ash level. The collector sample received from Nalco research laboratory were revalidated at Nalco Kolkata lab and finally at Tata Steel West Bokaro lab, confirming the promising results. (S.E 25-30 % better than HS Diesel) The key factors playing out for this improvement initiative are a) Scope for improvement in Clean Coal Yield at same or lower ash level coupled with improved Selectivity and Separation Efficiency b) Introduction of a Synthetic Collector with a Green Chemistry and subsequent replacement of H S Diesel, which is highly inflammable with a less inflammable & safer product Trial was conducted at plant scale in two phases and comparative performance of the Collector vis-à-vis Diesel was evaluated across the following Coal Seams of Q- SE (Seam VII, VIII, VI, IX and X). The results generated are very promising and the improvements observed are summarized below. ? Separation efficiency improvement by more than 20% observed. ? Flotation Fines yield increase varied from 0.6- 1.5 % on raw coal basis across different seams. ? Consumption pattern is 20-25 % lower than Diesel. Keywords: synthetic collector, west bokaro, coal beneficiation, HSD

Sep 1, 2012

By B. Orberger

The fine fraction (< 2 mm) of the high grade Mn-ore from the world class Moanda deposit, Francevillan basin, in Gabon, contains up to 30 wt. % of manganese and about 0.4 wt. % phosphorous. A pilot study at laboratory scale integrating mineralogy and geochemistry before and after ultrasonic treatment was conducted on the fine fraction (< 2 mm) of oxidized Mn ore in order to reduce the phosphorous content and enrich this fraction in manganese. The fine fraction was dried, crushed at 2 cm and sieved at 2 mm. The two fractions (< 2 mm and 2 mm ? 2 cm) were investigated by X-ray diffraction and scanning electron microprobe ? electron dispersive spectroscopy analyses. Both fractions contain lithiophorite, cryptomelane and pyrolusite as Mn carrier, and goethite, muscovite, illite and quartz as contaminants. The Mn hydroxide nsutite was only found in the fraction 2mm ? 2 cm.The < 2 mm fraction is significantly richer in goethite, muscovite/illite, and quartz. Phosphorous carriers are mainly goethite (up to 2.8 wt. % P2O5), while the Mn minerals contain up to 0.8 wt. % P2O5. The Mn minerals are partly included in an agglomerate of goethite, muscovite/illite, and quartz. The < 2 mm fraction was treated by ultrasound for 30 s in normal water. Mineralogical and chemical analyses after ultrasound treatment showed that the Mn-minerals were largely liberated from the goethite-muscovite-illite agglomerate. Mass balance calculations show that after ultrasonic treatment the < 2 mm fraction was ? 50 % enriched in Mn and ?50 % impoverished in P.

Sep 1, 2012

By R. Venugopal

Hydrocyclones have been used extensively for more than 100 years to classify mineral slurries for recirculation in grinding circuits. Sometimes hydrocyclone classification is carried out in more than one stage to improve the efficiency of classification. Factors affecting separation efficiency include fluid velocity, density, and viscosity as well as the mass, size, and density of the particles. The geometric configuration also affects its efficiency; it includes parameters like cyclone diameter, underflow and overflow diameter, position of vortex finder, height of the cyclone, feed inlet geometry, and diameter etc. Besides changes in the basic parameters some modifications in cyclone has also been introduced from time to time which have affected its efficiency, some of these are :-(i).Introduction of magnetic force along with the centrifugal and drag force to control the flow of the magnetic particles inside the chamber.(ii). Introduction of sparger, air is introduced in the chamber in the form of bubbles, to control the flow of fine particles and hydrophobic particles. (iii). Introduction of dilution technologies for the dilution of thickened underflow. (iv).Introduction of new model. In spite of wide use and simple geometry, the real working principle of hydrocyclone chamber is extremely complex because of the swirling turbulent flow inside the device. In order to get more knowledge about hydrocyclones and to increase its efficiency, past 10-15 years simulation techniques are being developed. The simulation models also enabled a deeper insight into the static and dynamic behavior of hydrocyclones. Therefore, more emphasis on simulations by methods like Computational Fluid Dynamics (CFD), Finite Element method (FEM) is given. Overall, a status review of the work carried out on the analysis of hydrocyclone performance, modeling approaches and its contribution in the efficiency of mineral processing operation is highlighted.

Sep 1, 2012

By M. Saghaeian, R. Hejazi, M. Mohammadinejad, M. Zare

"Water quality and quantity at the Tailing Thickening Section of processing plants is considered to be a crucial factor and impacts the performance of several sections. Therefore, gaining stable and effective performance at the Tailing Thickener Section is one of the principal goals of minerals processing plants. Different factors such as: qualitative and quantitative sustainability of plant feed, the balance between the mass of input and output water flow, the dissolving method and distribution of flocculant and the amount of dirt, solid percent of thickener inlet pulp, affect the performance of Tailing Thickener. The present study investigates the successful improvement of Tailing Thickener performance at Jalal Abad Hematite Iron Ore Concentrate plant through optimizing the above operational parameters. For this purpose, the following optimizations have been done: homogeneity and sustainability of plant input feed rates, fine pulp removal collected by the bag filters at the input of the thickener, adding an quietness box before moving the tail pulp into the thickener to reduce the pulp turbulence, replacing flocculant pump and injection pipes, improving water mass balance which leads to optimizing and stabilizing the concentration of input tail pulp into the thickener, adding a mixer to increase the flocculant preparation time, increasing the locations for adding flocculant to thickener from 1 point to 6 points. Applying the above modifications and monitoring the Tailing Thickener performance over the course of months, has led to the improvement of recovered water quality from 500 ppm to 200 ppm, increasing the solid underflow of the thickener from 40% to 48.5%, and similarly, reducing water loss by 60%. Of other important effects, due to improvement of water quality, grade of final concentrate 0.5% increased and because of 73% increase in monthly working hour, concentrate tonnage 55% increased. Finally, sludge thickener optimization has had a significant effect in selecting and designing the dewatering system from the underflow of the sludge thickener."

Jan 1, 2018

By I. Gombköto, G. Mucsi, S. Nagy, F. Kristály, Á. Rácz, R. Szabó, B. Egyed

"Present paper deals with the investigation of a Hungarian pumice. Grinding experiments were carried out in a stirred media mill for various residence time. Ground samples were tested with laser particle size analyzer to determine and calculate the material fineness (particle size distribution and specific surface area). The lime adsorption capacity was measured to monitor the reactivity. Alkali activated cement paste was prepared using ground pumice with various alkali activators. Cube shaped specimens were produced from the paste and the uniaxial compressive strength was measured at the age of 7 days. The resulted alkali activated material structure was investigated by XRD and FTIR. The results of the experiments show that pumice fineness has strong impact on its hydraulic activity, hence on the compressive strength and the structure of the resulted binder. Relationships between grinding fineness, material structure and strength of the raw and mechanical activated material as well as the alkali activated cement were revealed. INTRODUCTION Pumice is a natural pozzolan which can be used as raw material for cementitious materials in limited portion owing to its low reactivity. Furthermore, due to its mineralogical composition it can be used for developing a new environmental friendly binder, namely alkali activated cements (AAC) which are inorganic alumina-silicate materials with good cementitious properties (Almalkawi et al., 2017; Özodabas and Yilmaz, 2013; Najimi et al. 2018; Yadollahi et al., 2015). Despite being a rather recent research topic, many papers and books have been published focusing on various aspects of alkali activation. There is great variety of raw materials that can be utilized for AAC production. However, primary raw materials are very expensive and secondary materials are heterogenous in composition. Therefore, a more homogeneous and low price silicate would help to balance the properties and cost of resulting cement and easing the way for commercialization of AAC. However, the control of its reactivity is of great importance which can be realized using mechanical activation by grinding (Juhász and Opoczky, 1990; Djobo et al., 2016; Mádai et al., 2015). The goal of present paper is to investigate the effect of mechanical activation of pumice on the properties of the resulted alkali activated cement."

Jan 1, 2018

During incineration of municipal solid waste (MSW), various environmentally harmful elements and heavy metals are liberated partly into bottom ash, and partly carried away with the off-gases and subsequently trapped in fly-ash. If these waste incineration residues are not properly processed and immobilized, it can lead to secondary environmental pollution to the air, soil and water. The stricter environmental regulations require a higher immobilization efficiency of the waste incineration residues, which is the main objective of the present cooperation research. Within the present project, a systematic scientific research on various MSWI residues has been carried out, including sampling, low or high temperature processing and leaching tests. In the present paper, the major results have been summarized. The research results reveal that through appropriate combined pre-processing and high temperature vitrification, the bottom ash and fly ash can be efficiently stabilized. The results achieved provide a valuable alternative route to treat the solid residues from incinerators, and to make efficient recycling and safe utilization possible.

Jan 1, 2014

By Pat Turner, Abrie Schutte, Tim Olson, Roman van Ommen

The key to good cyclone circuit design and operation in primary grinding circuits will be discussed. Cyclone circuit design issues include individual cyclone design features such as cone angle or materials of construction, as well as orientation and manifold configuration. Cyclone performance issues as well as maintenance considerations will be detailed in an effort to achieve consistent cyclone operation with minimal coarse solids in the overflow. The new gMAXTM. cyclones will be introduced and evaluated using operating circuit data in closed circuit grinding applications

Jan 1, 2003

By L. S. Bbosa

Single particle impact breakage experiments provide essential data to aid in understanding of rock fracture in comminution. Such experiments, conducted using devices such as the drop weight tester, split Hopkinson bars and more recently the rotary breakage tester, have been successfully used to characterize ore breakage properties in relation to measured fracture energies. The work presented in this paper highlights the techniques behind the calculation of impact breakage properties from each of these three devices. The breakage parameters that can be calculated from experimental data from each of these are to be described. Drop weight tests are used to calculate A and b hardness parameters using the standard JK breakage model. Split Hopkinson pressure bars are used to establish the ultimate compressive stress of particles through single impact breakage tests and the fraction of impact energy utilized to cause particle fracture. Low energy breakage tests using the rotary breakage tester are shown to be used in calculating particle breakage probability. Methods to calculate parameters related to particle breakage probabilities such as E0 and Ecrit are also discussed.

Jan 1, 2014

By Xiqing Wu, Tao Yue

"Magnetic seeding co-agglomeration, i.e. adding magnetic seeds, organic depressant (such as the starch), and pre-magnetization for co-agglomeration, was applied in the reverse flotation for hematite ore slimes. Samples of the hematite ore slimes and the pure hematite fines were investigated by the co-agglomeration, respectively. Flotation tests suggest that the depressing effect of starch in the flotation was further enhanced with the addition of magnetic seeds and the pre-magnetization. Following the laser size analysis and flotation tests, TOC adsorption analysis, VSM, surface charge measurement, AFM, FTIR study, and SEM imaging have been utilized to understand the depressing mechanism. Based on the results it was demonstrated that with the addition of magnetic seeds and the low field pre-magnetization, the adsorption of starch onto hematite minerals was strengthened through the magnetic seeding co-agglomeration. The co-agglomeration improved the flotation performance by introducing the magnetic interactions and acting the bridging adsorption of starch between fine hematite and magnetic seeds in a suspension, and then resulting in an intensified coverage of the starch onto hematite particles and positive action in the coagglomeration under the pre-magnetization.INTRODUCTIONFlotation is undoubtedly the most important and versatile mineral processing technique, and both its use and application are continually being expanded to treat greater tonnages and to cover new area. However, its influence was limited to a relatively narrow particle size range of 5–300 µm (Wills and Napier-Munn, 2006). The main reason behind this limitation lies in that fine particles have high specific surface area, so need relatively high dosage of reagents (collectors or depressants), and exhibit poor flotation performance while intermediate or properly-sized particles produce high flotation kinetics and need low consumption of reagents. In order to increase the recovery of fine particles, quite a few of flotation techniques have been investigated. Most of them are based on particle aggregation, namely, by enlarging the apparent particle size, such as carrier flotation (Valderrama and Rubio, 1998; Zhu et al., 2009), shear flocculation (Duzyola and Ozkan, 2010; Yin et al., 2011), selective polymer flocculation (Rubio et al., 2007; Song et al., 2012; Ng et al., 2015), oil agglomeration (Laskowski and Lopez- Vladivieso, 2004; Forbes, 2011), temperature responsive polymer flocculation flotation (Forbes et al, 2011), and etc. However, these techniques above-mentioned are mainly studied for the direct flotation of fine minerals, and most of these techniques have not found applications for iron ore slimes especially recovered by the reverse cationic or anionic flotation."

Jan 1, 2018

By Emile Scheepers, Chris Aldrich, Jacques J. Eksteen

The pneumatic injection of CaC2 powder into molten iron has become a very reliable and effective way to carry out desulphurisation. The key variables that influence the kinetics of this process are the condition and composition of the top slag, the oxygen activity in the hot metal and the injection conditions. Notable injection parameters include carrier gas flowrate, reagent flowrate, lance depth and initial sulphur concentration. A one-dimensional, steady-state model for momentum, heat- and mass transfer in rising gasliquid- powder plumes was developed for conditions relevant to the CaC2 refining process at Saldanha Steel?, South Africa. Combined with a model that predicts the contribution of the topslag to the process, the overall rate of desulphurisation as a function of time was determined, thereby quantitatively demonstrating the influence of the above-mentioned injection parameters on the kinetics of the desulphurisation process.

Jan 1, 2003

By H. L. Liu

With the exploitation of mineral resources, valuable minerals are more and more finer and poorer. Priority reclaiming liberation grind particle under rough grinding, will help to pervert loss of melts, raise dewatering efficiency of concentrate, reduce consumption of reagent. And it is propitious to reduce energy consumption and raise the utilization rate of resources. With the feature of coarse particle?s desorption and deposition, CLF flotation machine has special pulp circulating way, which is not only apply to treat coarse particle but also normal size particle. The paper advanced the history, the design principle, the structure feature and the application of CLF flotation machine.

Jan 1, 2014

By Kamalendu Bhunia

With the progressive depletion of known resources of good quality coal and minerals as well as the increasing demand of these minerals by different user industries, the emphasis has been shifted all over the world from selective mining to bulk mining followed by up- gradation to obtain the required quality of concentrate. The column flotation cell is one of the alternatives to reduce the gangue content of fines because of its inherent characteristics viz. easier to operate, low space required, no moving parts etc. A laboratory flotation column is used to conduct experiment. Present work has been undertaken to observe the effect of process variables (gas flow rate, feed/slurry flow rate, and frother concentration) on gas dispersion parameters (gas holdup, bubble surface area flux) in collection zone and to explore the effect of feed (slurry) inlet orientations and gas flow rate on column?s metallurgical performance. The effects of solid particle concentration, size and type (hydrophobic and hydrophilic) of solid on gas dispersion parameters have also been investigated. Test work has been performed in a continuously operating Perspex column (10 cm in diameter and 168 cm in height) using coal, sphalerite and dolomite as solid. Gas hold-up has been measured by phase separation method and mean bubble sizes are estimated from a drift flux analysis. The influence of operating parameters on bubble surface area flux has been discussed. It is observed that gas holdup in collection zone is affected by air as well as feed flow rates and also solid?s type. It is also found that addition of solid decreases the gas holdup and rate of decrease in gas holdup increases when solid concentration increases and particle size increases. Increase in gas flow rate increases recovery in collection zone due to increase in number of bubbles per unit volume of the column. From the experimental results it is evident that cross-current orientation of feed inlet shows slightly better metallurgical performance compared to other orientations. Keywords: column flotation, gas holdup, drifts flux, bubble size, bubble surface area flux, hydrophobicity, and recovery

Sep 1, 2012

By B. Csoke

As opposed to large household appliances, in the processing of which dissambling has an important role, this possibility is pushed into the background as the size decreases. The practicable solution is physical liberation of the used small electronic household devices (by comminution) and separation of the liberated components according to their physical properties. In the first phase of the experimental work the structural/material composition of the typical products (mixer, kitchen robot, hair dryer, coffee machine, iron, bread toaster, vacuum cleaner, oil fryer) was determined. In the second phase a physical liberability test for each appliance using a rotary shear/shredder for crushing and a hammer shredder for milling was carried out. In the third phase the experimental separability tests using an air classifier and a shaking air table, as well as an eddy-current and an electrostatic separator were performed. In the present paper the results obtained using the air classifier and the electrostatic separator, are reported. To follow the life of a grain a new methodological procedure was elaborated. The particle size fractions after comminution were sorted into material fractions (copper, aluminium, plastics, etc.), then separated, and finally the recovery of the material components in the products were determined. Furthermore, the joint separability was investigated from two points of view: 1) for grain fractions and 2) for each waste appliance. According to the tests carried out so far, it was established that it is reasonable to form appliance groups by selection (e.g. mixer, iron, bread toaster and similar appliances form the first group, while the sandwich oven,

Jan 1, 2014