Search Documents

By Zhang Baoshan

In this paper, the forced features and dynamic behaviors of stone-column composite foundation are concisely related. The characteristics of Rayleigh wave method is summarised. This method is proposed in which, the stress ratio of the stone-column to the surrounding soil and the bear­ing capacity of the composite foundation are determined. Through the engineering cases, it is shown that, checking and evaluating the composite foundation in this method, is feasible, with high speed and low cost.

Jan 1, 1991

By Ron Bromenschenkel

The State of California, Department of Transportation is currently retrofitting a major interchange near the San Francisco area. The project is located in a highly traveled area of Oakland with light rail commuter service near many footings. Over 600 micropiles are being used in conjunction with CIDH piles for footing stabilization. A specially designed Soil Nail pile will support footings for a new light rail utility structure. Pile testing features in this contract serve as points of interest for future foundation designs. The presentation focuses on substructure issues of this incterchange retrofit. Both design and construction considerations will be covered. Design Considerations: ? Project Description ? Structure inadequacies ? Design criteria ? Design contraints ? Retrofit strategy ? Consultant analysis ? Pile Designs and Test Sites ? Contract Specifications ? Construction Plan and Cost

Jan 1, 1998

By Peter Chou

A total of 117 slope stabilization drilled piers were installed as part of a major hillside revitalization project. The 110-million dollar development, known as Stratford at Kenwood, included an 18-story upscale senior residential tower, a 3-story healthcare building, and 4-story condominium buildings, offering approximately 580,000 square feet of living space with panoramic views of Downtown Cincinnati, Ohio. In an effort to establish a flatter hillside plateau for the new 4-story condominium and to create a cut and fill balanced jobsite environment, an 800-foot long row of drilled piers and a 600-foot long multi-tiered shear key system was used to terrace existing 1.5H to 3H: 1V steep slopes and support the new fill. These slope stabilization features reduced the amount of spoils needed to be wasted off-site and mitigated the risk of slope instability. An ODOT/FHWA research indicated that spacing of stabilization piers and necessity of top-connecting elements are highly dependent on pier diameter, spacing, soil type, depth to potential failure surface, surcharge loads, and pier deflection. Due to pre-existing deep buried swales, various load combinations, and the complex mechanism of soil arching effects between adjacent piers, both analytical and numerical computer modeling was performed to estimate the loading on each pier. New generation multiplexed, 3-Dimensional, Micro-Electro-Mechanical-System based inclinometers were installed between selected piers to confirm the pier design, and monitor the fill placement, as well as long-term slope stability.

Jan 1, 2009

By Michael Arnold, Jonathan Delgado

In 2017, Bauer Foundation Corp. (BFC) was awarded the contract to install the deep foundations for the new 17-story Hotel Tower and the Low Rise Casino Expansion at the Seminole Hard Rock Hotel and Casino in Tampa, Florida. The site was underlain by extremely challenging Florida Limestone geology and surrounded by occupied existing buildings and infrastructure. To overcome the challenges of the difficult subsurface conditions, and to successfully complete the foundation installation without impact to the surrounding buildings and casino operation, Langan Engineering (EOR) and BFC were required to modify both the design and installation techniques during construction. The scope of work included 147 temporarily cased drilled shafts to depths up to 230 ft (70 m) below ground surface (BGS), 76 permanently cased micropiles up to 200 ft (61 m) BGS, and more than 300 augered-cast-in-place (ACIP) piles up to 125 ft (38 m) BGS. Voids and zones of high permeability in the limestone created many challenges for execution of the foundation scope including ACIP piles overbreaks of more than 400% above neatline volume, and construction induced ground subsidence/collapses adjacent to structures supported on shallow foundations. This paper will discuss site limitations, design and construction challenges, difficult geology, varied soil conditions, and lessons learned. PROJECT The project is located at Seminole Hard Rock Hotel and Casino Tampa, Florida, as shown in Fig. 1. Seminole Tribe, the owner, started the construction of a new 17-story Hotel Tower and the Low-Rise Casino Expansion at the beginning of 2017.

Jan 1, 2018

By Colin Curtis

In recent years, Manchester Airport has undergone expansion including the construction of a second runway, a new terminal building (Terminal 3) and extensions to the existing Terminal 1. Manchester is Britains third largest airport and ranked 20th in the world for international traffic. Arup (Manchester) was engaged as consulting engineer in a multi-disciplinary role for the terminal works. Part of this was a geotechnical commission including site investigation and pile design followed by supervision. This paper reviews the piling for the old, new and terminal extensions. In total, five pile types have been utilised over the years. The original 1950's Terminal 1 was founded on driven cast in situ piles, with a later 1970's extension utilising rotary augured piles. The recent piling comprised continuous flight auger piles (CFA), driven steel tube and tripod bored; the latter in areas of restricted access or low headroom. The ground conditions are Made Ground over thin Alluvial and Glacial drift, in turn, over a generally weak to moderately weak gypsiferous mudstone. All the piles were socketed into the mudstone. In terms of the new CFA piles, quality control using the instrumentation monitoring was problematical, but a substantial static load and integrity test programme resolved pile performance. Part of the work is matching new pile performance with previously installed piles and the continued use of older piles with new loads. Research provided some data on the older piles, including some static load test data, which enabled back analyses of their design and likely behaviour. Differences in design methods, installation techniques and pile behaviour based on load tests will be discussed.

Jan 1, 2001

By William Babcock

Augered, Cast-In-Place (ACIP) piles can be an economical, reliable, versatile foundation system. They have also been a part of projects that were behind schedule and the subject of lawsuits. The ACIP pile is a specialty system that is more workmanship dependent than most deep foundation systems and is especially vulnerable to the problems and abuse of poor specifications and contract language. Many of the original specifications were based on grouting methods, and numerous misconceptions have followed the method. The Deep Foundations Institute (DFI) has been the leader in debunking the mystique that has hovered over the method and attempted to standardize the industry through publication of the manuals describing the method and how it should be inspected. DFI should be applauded for taking the lead and producing a reference document that can be used to educate the specification writers, designers, inspectors, and owners. It must be must appreciated that there have been other organizations that would not acknowledge ACIP piles as a legitimate member of the deep foundation family. Some consultants and designers have gone to the extreme of making it policy to not recommend the method for use. This presentation is one practitioner's view of the causes of problems as they can be traced back to the contractual conditions. It is intended to provide a broader and different perspective than those provided by the technical specialists. It does not necessarily reflect the position of the DFI or any of the organizations associated with the ACIP pile industry. It is intended to further the spirit of partnering on every ACIP pile project, to further the acceptance and promote the use of this unique system, for the benefit of all the parties. It should be recognized, however, that all of the participants can and do play a role in getting a project into trouble. My view is that projects that get into trouble usually have an early flaw that leads the project to the edge, and the project participants blindly follow the original mistake right over the cliff like lemmings. This instinctive reaction may be a survival tactic by going along with the group, because any one party that departs from the program or shows a position of weakness is a candidate for sacrifice.

Jan 1, 1997

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By Martin B. Hudson, Daniel Brescia, Zhangwei Ning

Due to the complexity and sensitivity of surrounding environments, instrumentation and monitoring (I&M) is critical for many urban deep excavations. The objects to be monitored include shoring bulkheads, retained embankments, adjacent buildings and roads as well as underground utilities. However, there are also plenty of constraints on the implementation of I&M such as: congested site space, difficult access to instruments, coordination among multiple contractors, and installation permits for private or public properties. Because of these constraints, sometimes the implementation of the initially planned I&M is delayed, its scope is reduced, and/or the continuity of monitoring is interrupted. For these reasons, it is important to implement the I&M with robust and redundant capabilities while providing minimal interference to the project construction and schedule. This paper describes state-of-the-art I&M technologies including automatic motorized total station (AMTS) with camera and automatic leveling device, reflectorless AMTS and IoT- based wireless sensors based on a case study of an on-going deep excavation project. INTRODUCTION In urban environments, deep excavations requiring the construction of temporary shoring bulkheads are becoming increasingly common, with the associated need to provide protection of the surrounding built environment during construction. Protection of the surrounding environment requires planning, engineering, construction, monitoring, and excessive shoring movement mitigation. The I&M is a vital component of the deep shoring implementation. In public projects, geotechnical I&M is often placed within the general contractor’s scope, whereas the majority of deep excavations are privately undertaken. For those private developments, sometimes the developer contracts the geotechnical I&M directly with the project geotechnical engineer or by a geotechnical I&M specialist hired by the project geotechnical engineer. In either the public project or private development case, the effective deployment of the I&M system relies heavily on coordination and collaboration with the project contractor.

Jan 1, 2018

By Richard J. Finno

Detailed measurements made at a test section adjacent to a deep braced cut and other published data are combined to illustrate the limitations of the common methods of predicting movements associated with excavations in soft to medium clay. While past performance data can be used to estimate expected responses before construction in many cases, actual wall and soil deformations throughout construction can only be estimated using finite element procedures. Success of such analyses depends equally upon considering all aspects of construction that induce strains in adjacent soil, such as wall installation, excavation and bracing sequence, and time, and adequately modeling soil stress-strain behavior. Even when these two criteria are met, soil deformations can not be predicted adequately when strain levels exceed those that produce peak shear stress.

Jan 1, 1991

By William D. Spielvogel

The Massachusetts Highway Department awarded the Porter Street Outfall Project to the J.M. Cashman Company in November 1991. Timely completion of the Project in one and one half years is critical to the start of the subsequent Third Harbor Tunnel North Approach project. Existing subsurface conditions and the Project's location at Boston's Logan International Airport significantly increases the difficulty of construction. The major contractual work involves relocating a reinforced concrete double box culvert supported on a continuous wood pile foundation. This existing culvert crosses and interferes with the future Third Harbor Tunnel North Approach alignment. Two parallel culverts constructed approximately 20 feet from either side of the future Third Harbor Tunnel alignment replace the existing double box culvert structure. Under the original contract design, approximately 3,100 feet of 14 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the west side of the Third Harbor Tunnel and is located in the center of the Airport's main service roadway, Harborside Drive. This culvert is the Porter Street Combined Sewer, PSCS, which handles a combined flow of sewerage from the East Boston community and storm water runoff from Logan Airport. In addition, approximately 2,230 feet of 17 ft. by 15 ft. reinforced concrete culvert is cast in place adjacent to the east side of the Third Harbor Tunnel and is within 20 feet of an active aircraft taxiway and heliport. This culvert is the Bird Island Flats Storm Drain, BIFSD, which handles storm water runoff from the Logan Airport airfield. The existing outfall, on the west side of the Third Harbor Tunnel alignment is to remain in service and is to be connected to the new PSCS and BIFSD culverts. Therefore, a portion of the BIFSD culvert is designed as a bridge to span 128 ft. across the Third Harbor Tunnel excavation during construction.

Jan 1, 1994

By Gregory A. Stephan

A case history of design, prediction, probe pile driving, and construction of a pile foundation for Building 3 of Waterside at Bay Beach Condominiums located in Fort Myers Beach, southwest Florida, is presented. Site geometry constraints, the presence of a 12.0 ft (3.6 m) deep lake occupying the southern one-third portion of the proposed building footprint, and marginal subsoils provided specific challenges for design and construction of the foundation. The subsoil conditions were explored by performing Standard Penetration Test (SPT) borings and a Piezocone Penetration Test (PCPT) Sounding to depths of 100 ft (30.5 m) within the building footprint. Additionally, borings were performed to envelope the building. Deep foundation alternatives included driven concrete, monotube, and steel pipe pile as well as drilled shaft. Following an evaluation of high structural loads, site-specific constraints, foundation test data from buildings 1 and 2, and preference expressed by the project owner, a pre-cast prestressed concrete (PPC) pile-supported foundation system was selected as an economical and effective foundation approach. Use of an augered cast-in-place (ACIP) pile foundation system was precluded by the project structural engineer. This paper deals with the design aspects and methodologies utilized in choosing and economizing the foundation system. The building foundation was designed for an allowable pile capacity of 40 tons (353 kN) in compression, 1.5 tons (12 kN) in lateral capacity for a deflection of 0.25-in (0.64 cm) and 15 tons (133 kN) in uplift capacity. For the single story extended garage structure, a pile capacity of 27 tons (238 kN) was indicated in compression. As part of the design process, an extensive probe pile driving program was carried out in order to evaluate the pile driving equipment, determine and verify pile capacities, and optimize the production pile lengths. A total of 33, 14-in (356 mm) square, PPC concrete piles were driven within the entire building limits, and dynamically load tested utilizing Pile Driving Analyzer (PDA) as part of the probe pile driving program. Utilization of PDA during probe pile driving helped in predicting pile set-up (i.e., increase in pile resistance with time) as well as reducing the pile lengths by as much as 20 percent. It resulted in variable pile lengths during the production phase. This information was effectively utilized as part of the overall quality control program to install a total of 559 PPC piles (including 33 probe piles) within the Building 3 footprint, including the reclaimed lake area, to depths ranging from 45 to 58 ft (14 to 18 m) below existing ground elevation as part of the foundation support system. Prior to installation of probe or production piles, a termination criterion was established using 1-dimensional wave equation analyses in addition to the design pile embedment requirement. The predicted pile capacities compared reasonably well with the capacities from the CAPWAP analyses for probe piles. This engineered, monitored and tested foundation solution provided a cost effective and satisfactory basis for completion and approval of the foundation work for the building resulted in cost savings over other foundation alternatives for the owner. The building has since been occupied and a recent reconnaissance has indicated that the building foundations are performing satisfactorily.

Jan 1, 2003

By Gary L. Seider

Helical screw piles are used in various applications including the underpinning of distressed foundations and as deep foundations for new structures. At present, maximum design loads range between 12.5 and 50 tons. Helical piles installed with in-situ grouting of the central steel shaft are a relatively new type of deep foundation, which have extended the present maximum design loads to the 100-ton range. Vickars & Clemence discussed this new foundation system in a paper presented at GEO-Denver 2000 in Denver, CO. Over the past three years, grouted shaft helicals have been used successfully on remedial and new construction projects all across North America. The authors have studied several construction projects in a variety of soil conditions to compile a list of practical design guidelines. Those guidelines include installability of grouted shaft helicals based on soil type, equipment requirements, grout selection, and theoretical vs. actual load capacity. In a number of cases, full-scale, field load tests were conducted in both granular and cohesive soils and the results broken down between tip resistance on the helix bearing plates and friction resistance on the grouted shaft. Data is presented which will further efforts to develop a design model and method to accurately predict the axial and lateral capacity of grouted shaft helicals.

Jan 1, 2003

By Wolfgang G. Brunner

The center of Berlin is currently a huge jobsite, where international architects, designers, consultants, construction and ground engineers as well as investors take on the challenge of the biggest and probably most complicated projects in terms of soil conditions in Europe. The Berlin sand is generally suitable for foundation measures, but can be very tricky in deep excavation pits below the high ground water level. The reason for this is its uniform grading, medium dense stratification and lack of cohesion. The requirements for these deep pits are: - measurements in the range of up to 120 000 m2 per pit - depths up to 19 m below ground water level - lack of dense horizontal geological layers - no permission for lowering ground water levels - toughest ever European competition in construction. Sheet pile walls, sheet piles set into cut - off walls, secant pile walls, diaphragm walls, all with tie backs under high water pressure, are used as retaining sytems. The pits are closed at the bottom against water either by under water concrete, deep lying grouted cut - offs or high lying jet - grouted cut - off slabs. The huge dimensions of these excavation pits are a new challenge for ground engineers, and new technology had to solve the upcoming problems and resulted in new experience.

Jan 1, 1999

By Sugie Prawono

Jacked pile is the only piling system in which the load capacity of the pile, at any penetration depth, could be monitored directly during its installation process. Each installed pile could have a graph of jacking load versus depth of penetration. For safety purposes, the maximum applied jacking load during installation of a pile could be assumed as the minimum load capacity of the pile. This load capacity will increase with time since the drop in soil strength due to the installation process will recover later on. In order to determine accurately this jacking load, a research was carried out by comparing the load capacity of a pile at certain depths to the jacking load recorded during the installation process. The load capacity could be calculated using cone resistance, qc, and local friction, fs, from Dutch Cone Penetration Test. A graph could be drawn of the load capacity against the depth. By applying a correction factor, a, to the data of local friction, the calculated graph could be matched to the graph of recorded jacking load. The a factor is found to depend on the soil type, which is in this case, represented by the magnitude of cone resistance. The soil type is divided into 3 categories according to qc values (qc < 500 Kpa; 500 Kpa < qc < 2000 Kpa and qc > 2000 Kpa). Graphs of the a factor versus depth and a sample of calculation are presented in this paper for easy application.

Jan 1, 1999

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989

By N. C. Matheson

The West&apos;s Shell Pile has been used on sites with very soft ground conditions for over 60 years. Fibre reinforced precast concrete shells 900mm long are threadled onto an internal mandrel which can be extended according to the depth driven to attain the load bearing resistance. On completion of driving the mandrel is removed leaving the precast shells to form a permanent lining to the cast insitu concrete core. To give resistance to high contamination, a tar based epoxy coat is sprayed on the outside of the shells or a flexible PVC liner is installed inside the shells to protect the core. Fundamental to the resistance to contamination is the quality of the precast fibre reinforced concrete shell, the mix design and method of manufacture. A series of detailed laboratory experiments were carried out using samples immersed in concentrated acid and sulphate solution. The long term effects of exposure to contamination is recorded in the case studies of existing piles at two gasworks sites.

Jan 1, 1989

By Julie Shang, Tim Evans, Michael McDonald, Yu Guo, Bingfeng Xue

Effective chemical grouting represents a technical and economic solution to many challenges related to soil stabilization and blocking the flow of water. Chemical grouts are facing increasing demands in durability, environmental impact and value. To better meet these challenges, a novel and cost effective process was developed to produce a sodium silicate that increases the ratio (i.e. silica to alkali) beyond what has been used in traditional silicate-based grouts. The move to a lower sodium form of silicate was anticipated to have two desirable performance enhancements; a reduction in leachable sodium and improvement in the durability of the silicate grout. An in-depth study was performed at the University of Western Ontario Geotechnical Research Centre to quantify improvement in durability as well as other performance properties such as compressive strength. The study began by first modelling the gelation time and reaction kinetics of the high ratio sodium silicate over a range of silicate concentrations using two different setting agents as well as with/without a hardener. As expected, reducing the level of sodium produced a much more water resistant grout. These same formulations also showed a four order magnitude reduction in permeability. Somewhat surprising, test results showed the higher ratio silicate having much higher compressive strength. At the time of this abstract, the high ratio silicate was moving to the trial stage for geotechnical applications while the petroleum industry was further along with several successful field trials for water blocking as well as cement remediation. This paper will review the chemistry, testing and features of this next generation form of sodium silicate. Introduction Sodium silicate based grouts have been used for decades for soil stabilization and water control. Over the years, several silicate-based systems have been tailored for specific application conditions to maximize performance and reduce cost. Past research has also focused on the selection of setting agents and hardeners for silicate grouts. A constant in the development effort has been the grade of sodium silicate. The vast majority of chemical grouts have been formulated using a ~3.2 ratio sodium silicate. As a very brief overview on the meaning of “ratio” and why it is so important to performance properties. The ratio describes the proportion of sand to alkali or SiO2:Na2O used to make different grades of sodium silicate. Comparing a 2.2 ratio to a 3.2 ratio, it is easier to polymerize and set the 3.2 ratio. Upon setting and forming a silica gel, the system has higher compressive strength values and improved durability with a reduced level of syneresis (i.e. shrinkage). This leads to the question if 3.2 is better than 2.2 why not go to 4.2 or higher?

Jan 1, 2018

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By David C. Kraft

Helical piles and ground anchors were used to meet critical design and constructability requirements for an urban forest Canopy Walk at the Atlanta Botanical Garden, Atlanta, GA. The 12-foot wide pedestrian walkway path was to be nestled among the treetops of a forest, extending to 600 ft. in length, and soaring 40 ft. high above the forest floor. Of particular concern during construction was that the foundation system for the temporary steel shoring system had to be non-invasive to the subsoil, could not damage the forest floor, trees, root systems, or foliage, and upon completion of the concrete walkway pour, could be removed, again without disturbing the subsoil. Accubrace, Inc. designed and installed all the helical foundation types, as well as provided steel braces, typically used in Tilt-Up building construction, for the walkway project. The braces, some extending to 43 ft. in length, were used to provide lateral support against wind loads for the walkway form. In addition, the braces acted as secondary support for lateral loads during the placement of wet concrete along the 600 ft. length of the walkway. Helical foundation products installed included vertical compression piles, ground anchors for tension rods, and ground anchors for the braces. The installation of the piles and anchors was particularly challenging since the forest floor elevation varied as much as 50 ft. due to the presence of a ravine. Information is provided on the subsoil conditions, required loads, design, installation, and acceptance criteria for each helical product type installed for the project. The results of vertical and lateral load tests on the helical piles in the pre-construction phase, conducted in conformance to project specifications are presented. Photographs to illustrate the nature and complexity of the project are included. The concrete pour for the walkway was successfully completed on December 12, 2009, and the walkway was opened for visitors in May, 2010.

Jan 1, 2011

By Jason Weck, Alper Turan, Ali Chehadeh

"Rapid expansion of urban areas dictates the need to expand/rehabilitate the existing buried infrastructure at the same rate. The technical challenges such as variable soil and rock profiles, high groundwater tables and limitations imposed by the built environment combined with present fiscal and schedule limitations necessitates the implementation of fast and cost effective construction methods. Since drilling procedures and equipment allow the construction of overlapped pile systems in almost all subsurface conditions, the secant pile walls have become a cost-effective shoring option for such infrastructure expansion/rehabilitation projects. The secant pile walls constructed in a circular plan layout to form a vertical shaft provide unique advantages since they act as a compression ring. Secant pile walls require stringent drilling tolerances be achieved in order to provide structural support and to work as a compression ring in addition to a groundwater cut-off wall.This paper outlines design methodology, installation procedures and verification techniques used for the secant pile compression ring for the Waterloo Landfill Pumping Station No.2. The secant pile compression ring had a 6m inner diameter with over a 20m wall depth and over 18m excavation depth. The details of subsurface conditions, analytical and numerical methods used in design are presented here. The details of the monitoring system are introduced and results of monitoring are presented and compared with analytically estimated and numerically simulated quantities. The results presented in this study are considered to be of interest to those involved in design and construction of vertical circular shafts."

Jan 1, 2014