Search Documents

By Mohammad Noaparast, Babak Fotoohi

"Due to certain advantages in (semi-)Autogenous-Ball mill circuits in most of the high-throughput ore grinding units of mineral processing plants, much attention is paid to optimize the mill performance. Despite the maturity of the grinding mill mechanical design, there had been made less attention to the efficiency of the grinding media in the past. In this research, the possibility of establishing a relationship between liner/lifter wear rate and variations in the composition of the iron ore (from Chadormalu mine) is investigated.Measurements and determination of liner/lifter wear rates and patterns concluded in recognition of critical liner segments exposed to much abrasion during the ore grinding. After metallurgical analysis of liner materials and correlation of wear rate with the ore composition, the homogeneity in the metallurgical microstructure of the alloyed steel (such as the uniform distribution and amounts of the constituent phases) was determined as the most influential factor in the response of the liner/lifter to the variations in the ore composition. Magnetite with greater abrasion index than hematite, in finer particles, is responsible for additional abrasion of liners; hematite with greater work index exists in the mill with larger particle sizes, thus it could produce wear on liner parts with less tolerance to impact as is the situation for martensitic steels.INTRODUCTIONThe mineralization in Chadormalu plutonic iron ore deposit is consisted of mostly magnetite, hematite, martite, apatite, quartz and carbonates. The average composition of the ore is presented in Table 1. In the processing circuit, the gyratory crushed ore reduced to 30 cm would finally be the feed to three similar 32’ semi-autogenous mills in parallel processing lines. The pulp in the mill would have the characteristics mentioned in Table 2. The quality of the mill output has its direct effect on the downstream processes either physically or chemically (e.g. in cycloning or flotation respectively). In order to take advantage of optimum performance for these circuits, a close control of the ore grinding conditions is necessary; because any shortages in throughput, liner/lifter damage or changes in ore composition could bring the unexpected casualties. In this work, it has been attempted to find (possibly) a reasonable relationship between variations in ore characteristics together with liner quality and the amount of wear rate in different liner/lifter segments of a semi-autigenous mill. Liner/lifter segments are supplied by three different domestic steel making companies. The alloy structure of the liners/lifters is made up of pearlitic chromoly steel."

Jan 1, 2005

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By Y. Özçelik

Rocks show a variety of engineering and physical properties that affect typical quarry operation such as diamond wire cutting in the marble quarry. The physical and mechanical properties of rocks depend on their mineralogical and petrographical characteristics. The purpose of this study is to investigate the effects of mineralogical and petrographical properties of a rock, such as grain size and mineral content, and how these affect the wearing of diamond bead and cutting rate in a diamond wire cutting operation in a marble quarry. Statistical analysis is used to carry out the study. Three different rock types were examined, namely, hard rock (andesite) and softer rocks like limestone and marble. The study revealed that the mineralogical and petrographical properties of the rocks, such as percentage of quartz, biotite, plagioclase, matrix minerals, and opaque minerals, are important. In addition, the grain size of quartz and plagioclase in andesitic rocks and calcite grain size for carbonate rocks significantly influenced the wear rate and cutting rate in diamond wire cutting operations.

Jan 1, 2005

Conventional waste management practices produce two waste streams for the construction of separate disposal facilities. The design of tailings impoundments is usually controlled by physical stability. Waste rock materials offer high shear strength characteristics for waste dump construction, however the hydraulic properties promote oxidation. The problem of oxidation is significantly reduced for tailings due to a fine texture that augments water saturation. Co-mixing of tailings and waste rock involves the intimate blending of tailings and waste rock to create a new material with superior physical and hydraulic properties. The new material has a low hydraulic conductivity, low compressibility, high water retention capacity and high shear strength. Co-mixed tailings and waste rock restrict oxygen entry and water seepage to minimize acid generation and metal leaching. Co-mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repository. The results of a laboratory program to characterize the physical and hydraulic properties of Comix tailings and waste rock are presented here. Various ratios of tailings were blended with three distinct waste rock materials. The saturated hydraulic conductivity for the Co-mixed materials was found to vary between 2 x 10-7 m/s and 5 x 10-8 m/s depending on blend ratio, waste rock type and compaction. This paper introduces concepts for the co-disposal of tailings with waste rock and evaluates the hydraulic behaviour of a Co-Mix waste system. The potential benefits of Co-Mix are shown for a typical mine.

Nov 1, 2002

By K. J. R. Ford

"Significant advances in mining and metallurgical operations have occurred over the last two decades, to define ore bodies via geological mapping, mineralogical analyses, geostatistical models and resource reserve modeling. Metallurgical process measurement, controls and modeling have also significantly progressed, with advanced instrumentation, control software, data capture systems and simulation tools. This progress together with development of the science of geometallurgy has allowed geologists, mineralogists, miners and metallurgists to start working together to define geometallurgical ore units and link these to mine planning and projected metallurgical performance. However, application of full geometallurgical programs into existing mine-processing operations or into new “greenfield” projects has been slow. This is mainly due to higher costs, limited dedicated technical resources and little or no corporate leadership. Additionally, life-of-mine cash flow models, the “dollars”, have been largely driven by ore tonnage rates, pay-metal grades and fixed pay-metal percentage recoveries, with few or no geometallurgical parameters included.Here defined, the “electrons” represent intrinsic ore characteristics embracing chemical composition, mineralogy, gangue components and their associated fundamental metallurgical processing phenomena. With its ever expanding treasure chest of measurement and modeling tools, geometallurgy paints a much clearer picture of the “electrons” for the geologist and metallurgist. But to fully understand and realize the real net value of ores over the life of a mine, a comprehensive link of “electrons to the dollars” is essential. Intrinsic characteristics of geometallurgical ore units are by definition linked to their metallurgical processing, but importantly need also to be related to operating costs, capital requirements and revenue.This paper discusses this important linkage under topics of ore geology and mineralogy, metallurgical processing, waste disposal, environmental issues, metal refining, project engineering and lifeof- mine models. Topics are illustrated by multi-metal references and by case examples from gold ore heap leaching and manganese ore smelting projects. 1"

Jan 1, 2013

"The application of telerobotics to mining is currently being introduced into production systems around the world. Mining companies in Canada, Sweden, South Africa, and Australia have tended to lead the international charge to this form of technology for mining. While this introduction is taking place, a few basic questions have yet to be answered. How many machines can a single operator run? How many types of machines can a single operator run?A Canadian Research Chair in Robotics and Mine Automation has been established at Laurentian University to investigate these questions and many more through a series of experiments in a telerobotics laboratory that connects Laurentian teleoperation workstations to model mining machines at Cambrian College’s eDome. The laboratory supports many experiments allowing researchers to physically run multiple robot scenarios differing the numbers and types of machines at one quarter scale. Further experiments are being designed to investigate the potential for managing time delays in telerobotics. This paper describes the laboratory, experiments, and some preliminary results."

Jan 1, 2005

By S. Banisi, M. Poorkani

The Sarcheshmeh copper deposit contains 1 billion tones of ore averaging 0.7% copper and 0.025% molybdenum. It is located southeast of Iran and currently processes 41,000t/d. Molybdenite as a by-product is recovered in two separate stages. First, a bulk coppermolybdenum concentrate is produced and in the second stage these two are separated. The recovery of molybdenite in the first and second stages is 65% and 85-90%, respectively. The yearly production of molybdenite concentrate varies between 3500 and 4000 t. Sodium sulphide is used as the depressant of the copper and iron bearing minerals which due to a rather high consumption (17.7 kg/t) constitutes one of the major cost items of the plant (i.e., 58% of total reagents cost). A detailed laboratory scale study showed that replacing air with nitrogen could reduce the consumption of sodium sulphide (i.e., H2S or mineral origin). Nitrogen for the plant was supplied from an oxygen plant used for the smelter through a 1400 m long pipeline. The existence of the oxygen plant at the Sarcheshmeh complex was a key factor in the implementation and success of this project. After using nitrogen in the plant for a period of twenty one months, the consumption of sodium sulphide was reduced from 17.7 to 14.2 kg/t at constant metallurgy. The reduction was lower than expected which was mainly due to the type of sodium sulphide used and the lack of any automatic instrument to control the depressant (sodium sulphide) dosage. The latter in turn caused the operators to overuse sodium sulphide in order to reach and maintain the target metallurgy (i.e., higher molybdenite recovery along with lower copper content of the concentrate).

Jan 1, 2005

By Karl Marquis

La Mine Mouska exploite depuis deux ans certains blocs de réserve à l?aide de la méthode long trou. Même si, à priori, la méthode long trou semble rentable, le contrôle de la dilution ainsi que le respect d?un échéancier serré s?avèrent primordiaux afin que cette méthode d?exploitation puisse être justifiable économiquement. La présentation suivante fera la comparaison économique entre cette méthode et celle de chambre-magasin.

Oct 1, 2001

By Carolyn Kenney, Jianjun Liu, Zhenghe Xu

"The flotation of fine particles has been a challenge to scientists and engineers in mineral processing. A novel concept of reactive oily-bubbles as carrier to float fine particles is described in this paper. The reactive oily bubble flotation is considered attractive for fine particle flotation. In addition to the role of fine particle agglomeration by oily films, the surface properties of air bubbles coated with a thin oil film can be better controlled for the desired selectivity by adding certain types and concentrations of water insoluble collectors into the oil phase. This approach can eliminate the addition of collector to the aqueous phase, avoid undesired synergetic interactions among collectors, activators, depressants and dispersants present in slurry, minimize undesired activation of gangue particles and significantly reduce the amount of collectors needed.The concept of using reactive oily-bubble to achieve selective flotation was demonstrated in contact angle measurement and by microflotation tests with fine sulphide minerals: sphalerite and galena in this paper. The flotation behavior of sulfide minerals can be radically modified with adjustment of solution pH, addition of depressant and activator as in conventional flotation. The successful separation between PbS/SiO2, ZnS/SiO2 and PbS/ZnS was demonstrated using mixed mineral systems. Compared with conventional flotation, the reactive oily-bubble flotation showed a stronger collecting power.INTRODUCTIONThe challenge for fine particle flotation has long been recognized and well documented (Fuerstenau, 1980). Because of drastic changes in surface properties of fine particles and associated physicochemical and hydrodynamic conditions of flotation systems, fine particles responded poorly to the conventional flotation processes. For instance, the small mass and hence low inertia of fine particles would result in a low efficiency of collision and attachment of fine particles with flotation bubbles. Large specific surface area of fine particles, on the other hand, would cause an increased reagent consumption. Dominating colloidal forces of fines may cause slime-coating, accompanying a low selectivity (Somasundaran & Arbiter, 1979; Fuerstenau, 1980; Sivamohan, 1990)."

Jan 1, 2003

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

By P. D. R. Maltby

"1. INTRODUCTIONMy talk today will discuss a new development in the thickening of slurries and clarification of waste water - the Enviro-Clear thickener. Several industrial installations of the thickener have been made in North America in the following applications:1.,water clarification in sugar beet processing plants.2.,separation of pregnant liquors from solid wastes following acid leaching in uranium mills3.,clarification of waste water from coal treatment plants as described in a paper in the June 1975 transactions of the SME entitled ""Application and Utilization of the Enviro Clear Thickener in a U.S. Steel Coal Preparation Plant"" by A.A. Terchnik, D.T. King and J.S. Anderson.2. HISTORYThe application of the Enviro-Clear thickener can be traced back to the filing of U.S. Patent 3523889 in 1970 by the inventor F. Eis. The claims of this patent are shown in Slide 1.The new concept was developed for sugar beet processing by the Spreckels Division of Amstar Corporation, and several such thickeners have subsequently been installed in various sugar beet plants. The Enviro-Clear Co. or New York took over the world-wide manufacturing and marketing of the thickener. Experience in the sugar beet industry indicated that the Enviro-Clear thickener volume requirements could be reduced to as low as one tenth that of a conventional type thickener. Various coal samples were supplied by U.S. Steel Research Laboratories for testing. The tests indicated that feed rate loadings of 3 gpm/ft.2 could be obtained by the Enviro-Clear thickener. Such results led to several industrial applications in the coal industry. Subsequently other branches of the mineral processing industry have come to learn of the possibilities of using this thickener. Slide 2 shows a list of commercial Enviro-Clear installations at the end of 1975."

Jan 1, 1976

By Luis A. Tondo

The Paracatu Expansion Project III in Brazil was implemented between 2006 and 2008 to increase the existing capacity from 20 to 61 Million tons per year of gold ore treatment. This expansion led the Brazilian subsidiary of the Canadian Kinross Gold Corporation to become the single largest gold producer in Brazil and the largest single gold concentrator in the world, with a nominal capacity to treat around 167,000 tons per day of ore. This paper describes the Project Development areas for the Paracatu Expansion, using the approach proposed by the Project Management Institute (PMI) and the methodology included in the PMBOK (Project Management Book of Knowledge). The author has more than 20 years of experience in the gold mining industry, having worked as a plant metallurgist, mill superintendent and development manager for RPM until he took the position as the Project Manager of the Paracatu Expansion III in 2005. Luis Tondo has a BSc in Mining Engineering from UFRGS-Brazil, an MScEng from the University of Queensland - Australia and an MBA degree from FDC-Brazil. Luis is currently based in Santiago-Chile, acting as the Project Director for developing projects in Latin America for the Kinross Gold Corporation.

May 1, 2009

By F. Lindroos

A cornerstone in the LKAB Green Pellet concept is to produce pellets with a small footprint in terms of energy con-sumption, CO2 emission and emission of other elements harmful to the environment, like dust, sulphur dioxides, nitrogen oxides, chloride and fluorine. The concept also encompasses our determination to make pellet products that contribute to low environmental impact and low energy consumption in our customer?s processes. The presentation will focus on the pelletizing process. It will describe both how we have attempted to decrease the generation of unwanted components in the process gas, and how we have tested or evaluated equipment for external gas cleaning. We will discuss and give examples from recent and on-going efforts and outline some of the future challenges we see, to meet our own environmental standards and also the tough demands imposed by EU and national legislation, while striving to boost production.

May 1, 2011

By Ish Grewal

"Batch centrifugal gravity concentrators, which produce very high ratios of concentration, have become common place for recovering free gold within milling circuits. Their effectiveness has proven to be especially useful in recovering finer gold particles. The knowledge related to testing, modeling and scale-up of these systems has been well established over the recent decade mostly due to the efforts of the late Dr. Andre Laplante.Gravity separation technologies such as jigs, spirals and shaking tables can provide the increased mass yields required for minerals that occur at higher concentrations than gold, however their effectiveness tends to diminish at finer particle sizes. The development of high mass yield centrifugal concentrators has provided the opportunity to be able to recover a wide range of minerals at finer particle size classes when compared to the more traditional gravity concentration devices. These concentrators also provide additional benefits such as smaller unit footprint and automated operation.This paper discusses the background, current practices and future applications for high mass yield centrifugal concentrators in base metals, sulfides and industrial minerals. Bench scale, pilot scale and plant practice examples are also presented.INTRODUCTIONGravity concentration, one of the oldest mineral beneficiation processes, has evolved over the decades and continues to play an important role in modern mineral processing operations. The development and growth of froth flotation in the early part of the twentieth century led to a decline in the importance of gravity concentration. However, gravity concentration continued to be used for ores that are difficult to beneficiate using froth flotation; such as tin, tungsten, niobium/tantalum, iron, industrial minerals and oxidized coal. In recent decades, many operations have begun to employ a combination of both gravity concentration and froth flotation Since flotation relies on surface chemistry and gravity concentration relies on specific gravity differences, putting these techniques in series provides today’s metallurgist with unprecedented opportunities to maximize grade and recovery of many of these minerals."

Jan 1, 2009

By D. J. Hutchinson, M. Lato, M. Diederichs

Light Detection and Ranging (LiDAR)-based applications for geomechanical purposes have recently proven to be a highly reliable and accurate form of remote analysis and documentation. The ability to remotely collect, process and evaluate rockmasses for structural geomechanical applications has benefits ranging from safety to efficiency, and provides a permanent record that can be assessed before and after an excavation has been completed. With the collaboration of Queen’s University and Rio Tinto, the Iron Ore Company of Canada (IOC) mines in Labrador City, Newfoundland and Labrador, evaluated the practical application of the I-Site 4400 LiDAR equipment, in conjunction with the Vulcan geotechnical module for geomechanical purposes. The project provided a comparative analysis between conventional hand-mapping and digital analysis. The analysis indicates that digital mapping could be employed as an active tool within the general geotechnical workflow, where results would be used in pit wall and rockmass support designs. As well, the field work enabled the generation of effective operational guidelines and protocols to maximize scanning efficiency.

Jan 1, 2009

By Kristie Tarr

Portland cement is primarily used to solidify backfill in underground mine workings and it represents a major cost in mining operations. CANMET-MMSL has invented an alternative binder technology that does not contain any amount of Portland cement and is made using waste materials, such as development rock and smelter slag. The technology has been successfully tested with many types of base metal and ferrous slag. Research conducted in collaboration with several mining operations in Canada has shown that the CANMET-MMSL binder has considerable potential as a replacement for Portland cement in mine backfill. An integral part of the overall mining operation, backfill is used for two main purposes: safety and environmental remediation. Depending on the mining method used, backfill provides a working surface, stabilizes stope and pillar walls, as well as the surrounding rock mass, and controls caving of stope backs. There are several benefits associated with the replacement of Portland cement in backfill, including reductions in (i) the footprint by placement of slag waste underground, (ii) the environmental effects and long term liability resulting from disposal and containment of slag waste on surface such as acid rock drainage, (iii) GHG as a result of reduced Portland cement usage (the production of 1 ton of Portland cement produces 1 ton of GHG), and (iv) the significant costs associated with reduced Portland cement usage.

Oct 1, 2010

By Xie Qiang

It is known that the stress state inside rock discs under Brazilian tests is neither simple compression nor tension, but a complex combination of both stress types, as well as for a beam subjected to bending, where compressive and tensile stresses are separated by the neutral axis. In this study, AE generation was obtained on pure white marbles from south Portugal that were submitted to both Brazilian and bending tests. Main questions to be answered were: (1) Does Kaiser effect exist in tests which create complex distributions of tension and compression? (2) Are there any meaningful differences in AE behavior of marble under Brazilian and bending tests?

May 1, 2009

By M. Massinaei, S. Abasi, M. Oliazadeh

Reliable measurement and control of the pulp-froth interface (froth depth) in the flotation columns is critical to achieve the desired metallurgical performance. Shallow froths result in a reduction of grade because of particle entrainment and deep froths reduce recovery because of the drop back of entrained and weak hydrophobic particles to the pulp zone. The cleaner circuit at Miduk copper concentrator consists of three parallel MicrocelTM flotation columns 4 m in diameter and 12 m in height. The interface level of the flotation columns is measured by two pressure sensors located at 1.4 and 2.4 m from the cell lip (in the collection zone). In this study the performance of the level detection system at different operating conditions was evaluated. A calibrated float-ultrasonic location system was used for measuring the actual froth depth. The results indicated that the existing level control system was subject to considerable error. The absolute error was found to be 33.27 cm. This was mainly attributed to the constant set-point value assigned to the froth density (ρf=0.3 g/cm3), which actually varies with the operating conditions. The actual froth density at different conditions was calculated and its average value (ρf=0.12 g/cm3) was re-set in the control system. This resulted in substantial reduction in the level-detecting error. Recommendations for more accurate measurement of the interface level were presented. INTRODUCTION Froth flotation is a complicated process because of many involved variables. One of the most significant controlled variables in the flotation process is the pulp-froth interface (froth depth). The froth depth has a profound influence on the metallurgical performance parameters (i.e. grade and recovery). Shallow froths result in grade reduction because of particle entrainment and deep froths reduce recovery resulted from the drop back of entrained and weak hydrophobic particles to the pulp zone (Finch and Dobby, 1990). Various techniques have been developed for measuring the interface level of the flotation cells in the last few decades. These techniques can be classified as: Techniques based on hydrostatic pressure measurements (Finch & Dobby, 1990), Techniques based on the density gradient (float) (Moys & Finch, 1988), Techniques based on conductivity measurements (Uribe-Salas, 1991), Techniques based on temperature measurements (Moys & Finch, 1989).

Jan 1, 2019

By Richard Phiri, Mike Milupi, Jackson Kapobe, Anton Lemmer, Charles Mazala

Sustainability of plant operations in a rapidly changing mining environment requires a well-trained workforce to ensure smooth running of operations. To ensure availability of trained labor, Mopani Copper Mines PLC set up a training facility in 2013. The school offers training in Engineering, Mining and Process. The engineering section enrolls grade 12 school leavers for artisan training. Mining section offers comprehensive safety induction program to employees and contractors to meet the Mopani zero tolerance accidents safety policy. The process training section offers advanced training programs for plant operating personnel and university graduates. The program includes needs analysis, theoretical metallurgical modules, practical plant training and e-learning modules. The school also offers assaying and sampling courses. All the above courses are extended to individuals and other mining houses outside Mopani wishing to have their personnel trained. The Mopani sustainable development academy ensures that contractors engaged on the Mopani sites are fully registered, comply with all relevant regulations and have undergone induction program before they can be allowed to work on the mine. INTRODUCTION “Sustainable operation of the mining industry requires a continuous supply of trained human resources” (Kapobe et al., 2018). The publication by the Asian Development Bank (2014) argued that there was a mismatch between the demand for high-level skills and the oversupply of low-level skills. Globally, the mining industry requires continued supply of skilled manpower for its complex operations and long term projects whose sustainability is absolutely necessary. Implementation of newer technologies in plant operations to ensure cost effective and efficient operations requires trained and skilled labor at various levels to handle ever-changing challenges. Dutz (2007:152–156) made three recommendations for Building Worker and Management Skills in India: Strengthen enterprise - based training. The government should help ensure that the benefits of in- service training are widely recognized by enterprises, while simultaneously providing strong financial incentives Improve vocational training - Vocational education and training systems have been unsuccessful in preparing graduates to meet market needs, particularly because of a lack of interaction with industry. Public and private vocational education and training providers should be strengthened to make them more responsive to industry demands. Curricula should be updated to reflect modern technologies. Strengthen business, management education, management of research and commercialization - business and management education should be strengthened through public-private partnerships. Innovative management courses should be introduced. Although these recommendations were made for India, they also apply to Zambia and other low and medium income nations.

Jan 1, 2019

By H. A. Schnell

"The Phase I Mill at Cluff Lake in northern Saskatchewan was designed to accommodate a very specific high grade uranium ore. As this high grade ore was depleted, construction was undertaken on a new mill circuit (Phase 2) to process a more conventional lower grade ore deposit.The Phase 2 Mill expanded the ore throughput to 800 tonnes per day. The new process employs crushing, grinding, leaching, counter—current decantation, solvent extraction and magnesia yellowcake precipitation and drying to produce a yellowcake concentrate.This paper discusses the process decisions required for this expansion and outlines the new mill circuit. Included is a review of the start up in August, 1984.1.,INTRODUCTION The Cluff Lake Uranium deposit is located 720 kilometers north of Saskatoon in northern Saskatchewan. A high grade deposit was discovered in 1970 with the first production taking place in 1980 after lengthy hearings. The original mill (or Phase 1 Mill) was specifically designed to accommodate this very high grade ore for a very limited plant life.Pilot plant work was carried out in 1981 on the other lower grade ores found in the immediate Cluff Lake area. Feasibility and process selection studies were then undertaken as the Phase 1 mill was nearing its end of life. These studies were completed in March 1983 when approval was given to construct the new Phase 2 mill."

Jan 1, 1985