Search Documents

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By Kim Wiwchar, Elizabeth Mbaja, Lynne Dang, Jim Furey, Anita Marks

"Suncor Energy Inc., located north of Fort McMurray, Alberta, commenced pilot scale operation using a CPT 4’ diameter flotation column in March 2003. This larger scale trial follows two previously successful flotation column bench scale tests. They included an April 2002 trial with a 2.4” inner diameter column from the University of Alberta and a 20” diameter CPT column in August 2002. The column receives middlings stream feed from one of Suncor’s deep cone separation cells and is operated in parallel with a set of WEMCO flotation cells. The recovery, tails losses, and concentrate quality are being compared between the two systems. The column, to date, has been tested with all types of run of mine ore grades. Variables such as wash water flow and temperature, sparger nozzle size and location, sparger air/water flow rates, and column residence time has been adjusted to achieve better recovery and final product quality.Used in many mineral processing applications, column flotation is primarily used for the final stage of sulphide cleaning and flotation of phosphate or iron ore. As well, mechanical cells are often used in combination with a column to retrofit an operation and to produce a cleaner product.Initial results prove that this is the first successful application of a flotation column in an oilsand application. If viable, it will be an inexpensive process for recovery of bitumen from a middlings stream and able to produce a final product suitable for froth treatment.INTRODUCTIONSuncor’s oilsand is surface mined from the Athabasca Oilsand deposit north of Fort McMurray, Alberta. The oilsand is then mixed with hot process water (HPW) and the bitumen is slurried in a pipeline. Large separation cells as shown in Figure 1 float off the bitumen product, which is then steam or static deaerated and sent to Secondary Extraction for further cleaning. The tails stream from the cell is sent to the Final Tails Pumphouse (FTPH) for processing. The tailings flotation froth product gets recycled to the separation cell oilsand feed. The tailings are pumped from the FTPH to tailings ponds. The middlings stream is drawn off the separation cell approximately 9’ from the froth overflow level. It runs down, by gravity, to the scavenger banks for bitumen recovery. It was from this stream off of the Line 6 Separation Cell that the feed to the Canadian Process Technologies Inc (CPT) flotation column was taken."

Jan 1, 2004

By E. I. Robinsky

"This paper describes a new, proven approach for tailing disposal. Not only is the disclosed system less damaging to the environment, it is also less costly to operate, to close down and maintain in perpetuity. The basic concept is to discharge thickened tailing from one permanent location.This creates a conical or hill-like deposit which:(1) requires lower perimeter dykes for equivalent storage capacity;(2) eliminates decant towers and decant lines;(3) requires no steep dams built of tailing;(4) is stable:(5) requires only a small pond outside the deposit;(6) decreases pollution of the surrounding environment by water seepage and deflation; and(7) simplifies abandonment and ""closing-down"" operations.The approach is made possible by the fact that, at a sufficiently high ratio of solids to water, tailing material can be made to accumulate at slopes of 5 or 6 per cent -- considerably steeper than possible by traditional methods using low solids-to-water ratios. To achieve the necessary solids-water ratio (35 to 60 per cent), it may be necessary to install a thickener. It is expected, however, that at many concentrators it may be possible to discharqe relatively clear plant water through a line separate from the tailing line, thus reducing the load on the thickener."

Jan 1, 1976

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By I. P. Barbosa, P. S. M. Soares, I. O. C. Masson

"Permanent magnets have been applied extensively to several electronic products such as printers, TV sets, microphones, microcomputers and headphones, presently manufactured in large scale by industrial economies. Sm-Co alloys represent about 20% of the world market for permanent magnets and their industrial processors generate 20-30% of magnetic scraps which can be recycled. This paper discusses a process route to recycle SmCo5 using acid treatment, solvent extraction of Sm and electrowinning of Co. The results confirm the feasibility of the alternative proposed. Basic operational variables are suggested as guidelines to design a plant for recycling magnetic scraps.The use of hydrometallurgical processes to recycle scraps from the industry of permanent magnets has been suggested in some recent papers related to recycling of metallic alloys [ 1 ]. These research efforts might be understood as a worldwide tendency towards the development of self sustainable metallurgical processes which mean the reduction of environmental impacts.CETEM -Center for Mineral Technology leads in Brazil several research programs concerning recycling and treatment of industrial residues. The work on samarium purification and concentration by solvent extraction, producing also a solution of cobalt sulfate as partially reported here is one of these programs. Previous results related to the sulfuric acid digestion of SmCo5 are presented somewhere else [2]"

Jan 1, 1997

By Serge Ouellet

Identification and quantification of cementitious phases in cemented paste backfill (CPB) is difficult due to the fineness of tailings and the low binder content used in the mixture. Techniques such as X-ray diffraction and thermogravimetry were ineffective (mainly due to tailing mineral interference) to identify and quantify hydration products in most works reported in the literature. On the other hand, scanning electron microscopy (SEM) was used in many cases but mainly for qualitative purposes. This paper presents the development of a new approach based on a computer program (SEM-XMAP) that combines X-ray dot mapping images acquired by SEM and generates a coloured image representing the mineralogy and the microstructure of a given CPB specimen. The technique is applied to one CPB sample mixed with blast furnace slag (BFS) and acidic sulphated mixing water sampled in a mine dewatering system. The technique allowed identifying calcic matrix, unhydrated and partially hydrated BFS particles, and sulphated phases.

May 1, 2007

By Tad S. Golosinski

The paper describes Online Master of Engineering Program at the University of Missouri-Rolla and discusses the experience gained during the first three years of its offering. This innovative educational program is designed primarily for mature students with an engineering or science background who want to acquire or upgrade their knowledge of mining engineering. Students can specialize in several different areas of mining, such as surface mining, underground mining, mine environment and the like. All courses constituting the program are taken online, through the Internet, without the need to attend the UMR campus in person.

May 1, 2004

By Thomas Deschamps

The main objective of this work was to investigate the effect of binder addition on the geochemical properties of surface paste tailings. Nine leaching columns were prepared following different disposal configurations: non-cemented, non-cemented with cemented layers, and cemented .The proportions of cement by total paste weight were between 0 and 1% for a whole column; the maximum amount of cement in a single layer was 2%. The material used was a sulphide-rich tailings coming from a Canadian hard rock polymetallic mine. The columns have been flushed once a week during 30 weeks. The recovered leachates were analyzed for pH, Eh, conductivity, and a wide range of elements. The drainage rates were monitored during the initial disposal as well as after each column flush. The results show that binder addition can improve the whole environmental performances for some of the studied disposal configurations. The disposal configuration consisting of intercalation of three 2% cement paste layers within non-cemented layers (0.66 wt.% of cement for the whole column), and the configuration with 2% cement added only in the two bottom layers (0,44 wt.% of cement for the whole column), showed the best results in terms of water quality and drainage rates.

May 1, 2007

By J. D. Nye, I. A. Farr, W. J. D. Stone

"A unique deposit of barite exists near Brookfield, Nova Scotia. The crystals are extremely fine and the whole deposit virtually free of heavy metals. The deposit size was not large enough for conventional uses, such as the production of barium carbonate and drilling mud. In an effort to obtain maximum utilization, a program was begun to determine if U.S.P.-grade pharmaceutical barium sulphate for X-ray diagnosis could be produced. Early work was sufficiently encouraging to institute a development program under the federal Program for Advancement of Industrial Technology. This has been very successfully completed. Canadian and U.S. process patents have been issued, clinical trials have been successful, a production plant has been designed and the plant’s production sold. The processing plant will include magnetic separation for the removal of iron minerals, fine grinding by paddle milling to minus one micron and acid leaching. The process is unique in that at no time is the barium taken into solution.Information is given on the deposit, process, markets, use, plant capital and operating costs, and projected profits. The initial production plant will have an annual capacity of 2,000 tons per year of end product. Capital cost is $850,000 and annual turnover more than $1.5 million. As this capacity only represents approximately 15% of the North American market, rapid plant expansion is foreseen."

Jan 1, 1980

By Paul R. Clark

Outline of Presentation ? Brief review of gasification and IGCC ? Polygenerationand its potential ? Why gasification today ? Major technology providers and their activities ? US initiatives ? Alberta Energy Resources and application of gasification ? CO2 management ? Advantages and barriers to gasification ? Conclusions

May 1, 2006

By N. E. Mkadmi

Backfilling increases the stability of underground stopes and may help reduce the environmental footprint from the mining operation. The barricades holding the backfill in place must be designed to prevent failure based on the total and effective stress states, which depend on fill properties, stope geometry, and filling rate. This paper presents results from a numerical study aimed at analyzing the stress states associated with the response of paste backfill following stope filling, with an emphasis on the short term behavior. The simulations illustrate how stresses evolve with backfill drainage and filling rate in a vertical stope.

May 1, 2011

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong Operational Readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.The road blocks encountered are often from systems that one assumes will operate without trouble such as air-conditioning, or design assumptions that were taken years earlier in feasibility process stages, namely the capacity of existing systems that will connect the new plant to the existing facilities. The challenges associated with rectifying these issues in addition to the requirements to properly start-up and operate a new plant without impacting production are great, and it is imperative to have the necessary resources to react quickly to any problems.IntroductionCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Québec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary by-product of the process."

Jan 1, 2016

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

By Walter Valery, Peter Radziszewski

"The NewCrest Cadia operation boasts the largest SAG mill commissioned last June 1998. A request was made to shed some more light on possible SAG mill charge behaviour. Three different software were used to simulate SAG mill charge behaviour:Mishra/Rajamanis MillSoft DEM charge motion program, Radziszewskis agglomerated DEM charge motion program and Powell/Nuricks MillTraj outer trajectories program. The contexts simulated are: 20/30 % charge volume, 65/75/85 % critical speed using the Hi-Lo lifter configuration specified for the mill as well as a Hi-Lo 60 degre lifter face configuration. Further, lifter interval was also studied to determine the effect on power draft. Power predictions are compared with those obtained during the commissioning period.INTRODUCTIONThe NewCrest Cadia operation is located outside of Orange, New South Wales, Australia. With proven reserves of 190 million tonnes at a grade of 0.75 g/t Au, the mill was designed to process 17 Mtpa (2065 tph) of ore with an 86% copper and 73% gold recovery. The grinding circuit (Fig. 1, Table I) boasts the largest SAG mill (Fig. 2) and was commissioned last June 1998."

Jan 1, 1999

By K. Meyer

"The largest cost centres of the David Bell Mine concentrator are grinding, leaching and effluent treatment. Optimizing results during the 6th year of operation are listed below: o SAG mill slurry density control and operating strategies improved liner life and media consumption by 10 and 25%, respectively.o Poly-met liners clad the SAG mill except for the feed end. Lower noise levels and reduced mill downtime have resulted in an improved and more efficient workplace (time required for liner changes is 2 to 3%).o A comparative grinding media study using seven different marked media at the same time showed media wear rates range 120 to 198 mg/kWh and ball mill charge replacement frequencies of 8.3 to 13.1 per year, and that a meaningful wear test must include all media to be tested at the same time in the same mill. High quality carbon steel cylinders had the best economics.o Pre-aeration, using pure gaseous oxygen is accomplished in pipe reactors. Small bubble generators provide oxygen in the first three leach tanks. 1500 to 3000 kg of oxygen is consumed per day. Leach kinetics have improved and trends indicate increases in gold recovery of three to seven ounces per day at reduced costs. Effects of reduced cyanidation of accessory metals on the effluent treatment plant will be discussed in a separate paper."

Jan 1, 1991

By Raymond Philippe

Background ?Hatch Water has worked with most major mining companies in Chile on water supply and optimization projects ?Many(copper) mining projects are located in Northern Chile, which hosts the driest desert on earth Water supply options in Northern Chile ?River ?Availability/Rights ?Well(Brackish) Water ?Availability/Rights ?Municipal Wastewater ?Water rights ?Volume ?(Desalinated) Seawater ?Infinite source ?Cost depends on distance and altitude ?Recycling/Reutilization ?Water losses All these options present water quality issues

May 1, 2009

By Mehmet Canbazoglu, Kaarlo Haavanlammi, Hannu Laitala

Cobalt is currently a critical metal because of the increasing number of electrical vehicles forecast for production. Copper and zinc are base metals that are used in many everyday applications, including vehicle production. Eti Bakir Co. Mazidagi Phosphate Plants in the Mazidagi district of Mardin, Turkey is a multi-product facility that produces cobalt, copper, and zinc, as well as fertilizers, from the roaster calcine. Roaster off gas is treated in a sulfuric acid plant (SAP) and the acid itself is utilized in fertilizer production. The comminution circuit, roaster, SAP, and calcine leaching process were developed by Outotec and integrated with the fertilizer production process implemented by Eti Bakir A.Ş. This paper describes the hydrometallurgical calcine leaching process used at the plant, with a focus on the oxidative pressure leaching of the cobalt, zinc, and copper-containing calcine. The cold and hot commissioning phases of the pressure leaching autoclave start-up are discussed together with experiences from the ramp-up period. The production processes of the copper cathode and cobalt and zinc-containing salts are also presented together with some of the plant’s operating parameters. INTRODUCTION The ETI Bakir A.S. fertilizer plant, Turkey, is located in Mardin Province near the border with Syria, (Figure 1). The leaching plant project was started in 2012. The purpose of the plant is to separate the valuable metals from the calcine produced by the pyrite roasters, which are used to produce a SO2 containing gas for the new sulfuric acid plant. Fertilizer production requires sulfuric acid, and for this reason a sulfuric acid plant was built; customer already had access to pyrite concentrate, which is used as the roaster feed. During the engineering phase of the roaster and acid plants it was noticed that the roasted calcine contained considerable amounts of valuable metals like cobalt, copper, and zinc. To recover these metals, a calcine leaching process was developed at the Outotec Research Center in Pori, Finland. The main process connections of the Mazidagi site are shown in Figure 2.

Jan 1, 2019

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By J. D. Jorgenson

?? U.S. domestic production peaked at 120 Mt during years of the Korean Conflict120 Conflict ?? Pellet production increased, as highPellet high-grade ores decreasedores decreased ?? Until 1982 recession, most U.S. iron ore mines owned by steel companiesmines companies ?? Large Canadian iron ore mines brought into production after 1950into 1950

May 1, 2011

By Carl Bertrand, Patrice Nadeau, Claude Bazin

"Rio Tinto Fer et Titane processes the ore extracted from the Lac Tio orebody to concentrate the hemo-ilmenite (FeO.TiO2-Fe2O3) mineral that is subsequently smelted to produce pig iron and titanium oxide slag. The ore is crushed, heat treated (roasted) and concentrated using dry magnetic separators. This paper describes a model to predict the magnetic susceptibility of the roasted ore and its behaviour in the magnetic separation plant. The model uses a classification of the ore as a function of the size and magnetic susceptibility of the particles. A subsequent division into mineral species allows the simulation of the magnetic separation process. The model is used to assess various operating options when process disturbances occur.INTRODUCTIONOre processing operations consist of ore size reduction followed by the recovery of valuable species in a concentrate that is subsequently sold for its minerals or metal content. The concentration processes are based on the physical and/or chemical properties of the minerals contained in the ore. Flotation is typically used to recover minerals of base metals such as copper, zinc, lead or nickel. Iron ore and other dense minerals are typically concentrated by gravity separation processes. Magnetic separation uses the magnetic properties of the minerals to concentrate magnetite and other minerals, to clean coal concentrate and to recycle ferrosilicon for dense separation processes (Brophy, 1985).Magnetic separators can be divided into low and high intensity separators and high gradient magnetic separators (Gillet, 2008). Most of the low gradient magnetic separators are built as rotary drums that are operated in wet or dry conditions. Dry magnetic drum separators are used by Rio Tinto Fer et Titane in Sorel-Tracy, Canada to concentrate hemo-ilmenite from the ore extracted at the Lac Tio Lake mine near Havre St-Pierre, Canada. The analysis of production data suggests that process improvement could be achieved by identifying key variables for the control of the magnetic separation circuit and/or by modification to the circuit flowsheet. The use of a process model was considered to be an effective approach to conduct a preliminary analysis of the circuit with a view toward process optimization. However, the literature contains few detailed studies dealing with the modelling of magnetic separation processes."

Jan 1, 2011