Search Documents

By W. A. Wood, H. M. Bendler

Cylindrical fatigue specimens of OFHC* copper were subjected to alternating torsion while under axial tension. The superimposed tension strongly influenced the fatigue life of the specimens as well as causing characteristic changes in the structure of the fissures that form and develop throughout the life of the specimen. A further effect of the superimposed tension is a continuous extension of the specimen throughout its life in a manner formally similar to creep at elevated temperatures. RECENTLY, studies of the structural changes leading to fracture of metals by fatigue have been made by a technique which reveals, in section, the lattice distortion arising from slip movements inside the metal and the disturbances built up by these slip movements at the metal surface.1'2 According to this approach, fatigue develops as follows: a) fine slip movements concentrate in bands, producing little strain-hardening and thus permitting abnormal totals of plastic strain before fracture and, therefore, abnormal amounts of lattice distortion along each slip band; b) both forward and backward slip movements occur in each band which, according to their distribution across the band, may build up surface disturbances that include sharp notches; c) these notches early in the life of a specimen penetrate the distorted slip zones and transform them into deep, fine fissures; d) the fissures on continued cycling locally saturate the metal and cause local collapse in the form of a microcrack. Thus, the significant consequence of fatigue or cyclic

Jan 1, 1962

By M. Prats

Most of the information available on the heat efficiency of hot fluid injection processes, both water and steam, has been obtained from calculated temperature distributions in the pay zone and adjacent formations. The usual approach has been to write the heat balance equations in terms of the temperatures, and then to introduce whatever simplifications are necessary to help obtain an analytical or a numerical solution. In either case, the assumption has often been made that the vertical thermal conductivity in the flooded interval is infinite, so that the temperatures within the flooded interval are then independent of vertical position. Because it was first made by Lauwerier,l and has been used extensively since, this assumption will be referred to as the Lauwerier assumption. Excellent reviews of the literature on the heat efficiency of hot fluid injection processes have been given by Spillette,2 Flock et al.,3 and Ramney.4 Of course, the most significant contributions take into account the effect of a finite vertical thermal conductivity on the vertical temperature profile. The most general analytic expression for the heat efficiency of a hot fluid injection process is that of Antimirov5 who considers injection of a heated incompressible fluid into a reservoir through an arbitrary number of wells. The rate of heat injection into the reservoir, as well as the injection temperature, is an arbitrary function of time. The geometry of the horizontal flow is arbitrary, although the reservoir is considered to be of uniform thickness and properties and to be of infinite areal extent. Heat transfer within the reservoir is by horizontal convection and conduc- tion, and by vertical conduction. In the formations adjacent to the flooded interval, heat transfer is by conduction in any direction. Thus, the available expression for the heat efficiency due to hot water injection has been developed for rather general conditions. This degree of applicability has not been obtained for other thermal recovery processes. By making the Lauwerier assumption we have been able to obtain expressions for the heat efficiency that are essentially independent of the thermal recovery process, be it steam, hot-water, or underground combustion. Clearly, then, the approach followed here is more restrictive than that of Antimirov5 in that it uses the Lauwerier assumption. At the same time less restrictive assumptions are made about the horizontal heat transfer mechanisms, either in the flooded interval or in the formations adjacent to it. The main difference between our approach and that of other investigators is that the heat balance in the pay zone is expressed for the pay zone as a whole rather than for a volume element within it. The Lauwerier assumption is introduced after the problem is developed along these lines as far as possible. The details of the development of the heat efficiency are given in the Appendix, while the main features of the model are discussed in the next section. Results and their implications are discussed later in a separate section. The Model Certain assumptions have been made to determine

Jan 1, 1970

Organization Place Date 1919 American Electrochemical Society New York, N. Y. Apr. 3-5 American Chemical Society Buffalo, N. Y. Apr. 8-11 National Foreign Trade Council : Chicago, Ill. Apr. 24-26 American Iron and Steel Institute New York, N. Y: May American Institute of Electrical Engineers Lake Placid, N. Y. June 23-27 American Society for Testing Materials..: Atlantic City, N. J. June 24-27 American Railway Bridge and Building Association Cleveland, O. Oct. 21-23

Jan 4, 1919

By J. Mason

In order that the use of continuous mining machines be most economic, the equipment must be operated at rated capacity as much of the time as possible and downtime for repairs kept at a minimum. A large factor influencing any proposals for maintenance programs is the complexity of the machines—often the intricacies of the precision-built equipment requires engineering knowledge byond the scope of mine maintenance personnel. A training program is part of the answer; there are others. In addition to investigating a joint company-manufacturer equipment-design improvement program, Mountaineer Coal Co. has launched a detailed preventive maintenance program to combat extensive downtime often encountered when continuous miners are used. Everyone in the coal industry knows the importance of operating continuous miners at their rated capacity as much of the time as possible. The potential capacity of the miner is such that l-min. delay means from 3 to 8 tons of coal lost. Today's miner is a well designed, precision-built machine, complicated with hydraulic and electrical equipment and complex mechanical assemblies with all possible combinations of gears, levers, and rods. As the machine becomes more complex, the problem of maintenance becomes more acute. The transition from conventional to continuous mining has taken place so rapidly that the mine mechanic has been unable to keep pace. When there is a machine failure, the maintenance man usually employs either the trial-and-error or the play -it-by-ear method of repair, but this represents an expensive proposition. Mine mechanics, maintenance superintendents, and mine managers complain about the complexity of the machines and how difficult it is to keep them running. There is no shortage of skill in the design offices. Machines are designed by good engineers, but for engineers. What's the answer? Better trained maintenance men—better maintenance instruction—better field service. These are all good corrective measures, but the real cure is to provide for the men at the do it level. Designers have got to cooperate with men to simplify maintenance on the increasingly complex machine. The designer must be aware of how his machine can be maintained. Sometimes a simple design change in a bearing, oil seal, or a bushing will correct recurrent breakdowns. Parts such as filters, hydraulic cylinders, hoses, and pivot pins can be better arranged on the machine to make them accessible so that the mine mechanic can easily keep the machine producing. Therefore, to get our maintenance off on the right foot, the program must begin back in the design office, before the machine is delivered to the mine property. Realizing the importance of this aspect, our company set out on a joint company-manufacturer equipment-design improvement program. This is a formal program in which quarterly reports are written covering machine defects, design weakness, and general problems relating to machine maintenance and performance. The manufacturer in turn comments on each and every item appearing in these reports, indicating the action he proposes to take. In addition to the written reply, meetings are scheduled with manufacturer representatives to discuss further the outlined problems. The benefits realized from this organized program are both substantial and far reaching. Good maintenance begins with a good design. The subject of preventive maintenance is not a new one. Volumes have already been written on the subject. It consists primarily of doing the maintenance work when you want to rather than when the machine demands it. However, a preventive maintenance program can be overdone. Theoretically, if carried to ridiculous extreme, all working time could be spent inspecting and repairing the machines and no time would be left for production output. Our goal in maintenance is to maximize running time for all machines, and to prevent or at least minimize production downtime. INSPECTION AND REPORTING The center of any preventive maintenance schedule is regular and systematic inspection, but it must be

Jan 1, 1961

By G. Thodos, W. F. Stevens

The point-source function introduced by Horner' us a solution to the general unsteady-state equation for the flow of fluids through porous media has been utilized to calculate pressure profiles for adjacent wells as a function of time. By trial and error, the time at which the pressure waves meet to cause interference can then be calculated. For this calculation, the time of interference is arbitrarily defined as that time when both pressure waves exhibit a pressure decrease of 25 psi ar the same point within the formation. To illustrate the method, an example involving two adjacent wells producing at different rates has been worked out and is presented in detail. INTRODUCTION The initiation of production of a new well is usually accompanied by pressure drawdown measurements in order to establish the extent and characteristics of the formation. The interpretation of such pressure drawdown data is based on mathematical developments involving a single well in an infinite reservoir. If more than one well is present in a reservoir, the possibility of interaction between wells exists. Therefore, care must be taken in interpreting the pressure drawdown data. It becomes important to be able to determine when this interaction, or interference, becomes significant. This paper presents a method for the prediction of the approximate time of interference between two such adjacent wells. The basic differential equation describing the pressure distribution existing during unsteady-state flow of a slightly compressible fluid has been solved by Hor-ner.' for a constant production rate from a circular homogeneous reservoir of infinite extent. The solution utilizes the point-source function to define the pressure at various points within the formation as a function of time. The resulting expression is: q = production rate, STB/D ,;= formation volume factor, dimension-less µ = fluid viscosity, cp k = formation permeability. md H = formation thickness, ft C - fluid compressibility, psi' F = formation porosity, dimensionless R = distance from centerline of well, ft T = production time, hours Ei(—u) = Ei-function of U Eq. 1 may be used to calculate the pressure profiles generated during production from a single well in an infinite reservoir.

Jan 1, 1970

By Leslie C. Richards

The competitive position of producers of industrial minerals depends upon the delivered price of their product. Freight charges are a major factor in the sales to consumers. A comparison of freight rates on movements of limestone and silica rock in the Pacific Northwest shows a wide variance in mills per ton mile for like hauls, thereby favoring some localities over others. Introduction: Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By Leslie C. Richards

Sooner or later the potential miner of industrial minerals reaches the conclusion that of the various factors he must consider, the marketing of his product is. the most important. The sooner he realizes this the better, as successful industrial mineral producers .will confirm. Herein lies a difference between i.ndustria1 mineral mining and metal mining. Often in the latter, technical problems of mining or concentrating are equal to or even surpass those of marketing. This is not meant to imply that there are no problems in mining and beneficiation of industrial minerals, but these usually are outweighed by the problem of marketing. Recentlv. an official of a nationally known corporation :i the elecl.ro-metallurgical industry made an industrial mineral survey in the Pacific Northwest. In the course of his investigation he interviewed producers and potential producers of the various industrial minerals scheduled for use in the plant now being constructed in this area. He stated that he was interested in only three factors: namely, (1) Can your product meet our specifications? (2) Are you able to supply our tonnage requirements? and (3) What will be the delivered price? If there are several sources of supply of sufficient grade and tonnage, as is often the case in the Northwest, then the third factor becomes the important and deciding one. While industrial minerals are usually sold f.0.b. cars with the freight being paid by the buyer, it is the delivered and riot the f.0.b. price that determines the competitive position of the producer and his industrial mineral product. Unfortunately for both the consumers and producers of industrial minerals in the Northwest, the sources are generally a considerable distance from the markets. This necessitates long rail hauls, for which transportation charges make up the largest share of the delivered cost and the delivered price of the product. Is it any wonder then, that rail rates play such an important part in the marketing of industrial minerals? In order to sell his product, the producer must be able to deliver to the market at a competitive price. It must be remembered that his largest cost factor is rail transportation, and that he is limited to markets that he can reach competitively. Since the cost of rail transportation is so important, let us compare various freight rates in the Northwest and attempt to determine their influence on marketing. A study of all rates on all industrial minerals transported in this area, is beyond the scope of this paper. For the purposes of comparison, let us consider limestone (broken, crushed, or ground), and silica rock. These are widely used industrial minerals, and are carried by several different rail routes from.the sources of supply to the centers of consumption in the Pacific Northwest. Markets and Sources of Supply: Limestone has a number of uses in western Oregon and Washington. Among them are agricultural lime for the soils of the Willamette Valley and southwestern Washington; paper rock for the mills in such cities as West Linn, Oregon City, Newberg, St. Helens, and Salem, Oregon, and Camas and Everett, Wash.; chemical and metallurgical-grade limestone for the metallurgical plants centering around Portland, and the Tacoma-Seattle areas'; and sugar rock for the sugar refineries at Toppenish, Wash., and Nyssa, Oregon. Since limestone for cement manufacture is generally processed near the quarry, transportation

Jan 1, 1951

By P. C. Hodges

WHILE there is very little romance connected with the operation of a stone quarry, yet to those who have participated in the growth and development of a business that has been a pioneer in its field and that FIG. 1.-LOCATION OF PROPERTY OF MARBLE CLIFF QUARRIES COMPANY. has been in continual operation two-thirds of a century there is bound to be a background of experience, which if properly capitalized, brings progress as well as satisfaction in its accomplishment.

Jan 1, 1936

By W. T. Bell, M. P. Lebourg

The perforating of multiple tubingless completions, in which two or more strings of 27/8-in. OD casing are installed in the same borehole, presents two basic problems. First, good completion practices require an eficient perforator that leaves no debris to interfere with subsequent completion operations. Second, and of more complicated nature, a system is needed for controlling the direction of fire so that adjacent strings are not damaged. Development of of a 2-in. OD, steel retrievable, shnped-charge gun has solved the first problem. The second was resolved through development of three different devices to provide directional perforating for the two types of completion methods being employed today. These include a mechanical orienting device and two self-orienting radiation devices. Conceivably, the latter methods could be adapted to the directional perforating (of .upper zones) of conventional dual and triple completions without removing production tubing and packers. INTRODUCTION The recent trend to multiple tubingless completions,' wherein two or more strings of 27/8-in. OD casing are installed in the same borehole, has presented two basic perforating problems. The first problem to be overcome was the design of a gun that would result in efficient perforations without causing debris to bridge in these small-diameter casings. The second problem was, of course, to devise a system for controlling the direction of fire such that adjacent strings would not be damaged. The problem of gun debris in slim-casing completions has been well defined in the numerous 27/8-in. single tubingless completions which have been effected during recent years with the expendable-type perforators. Failure of expendable-gun debris to settle out properly, even with good gun break-up, has resulted in bridging inside these small-diameter casings. This, in turn, has interfered with completion and re-conditioning operations. The past two years have clearly shown, in fact, that debris problems are not confined to this small range of casing with most designs of expendable-type guns. A high incidence of bridging has even been reported in 4%-in. OD casing. The perforating of multiple tubingless completions has entailed, therefore, the development of a completely debris-free gun of adequate performance, as well as the necessary devices to provide positive directional perforating in the two completion methods presently being employed. THE GUN —DESIGN CONSIDERATIONS The design of a shaped-charge gun for slim-casing perforating has presented a maze of interrelated prob-lems. Since the primary specification has been leveled at efficient charge performance with complete elimination of gun debris, it has been necessary to develop a retrievable steel-carrier gun of tubular construction to house the charges. The carrier must be retrievable through 2.29-in. API pump-seating nipples which are usually installed in 2 7/8-in. strings. To provide for recovery of the gun from the well, swelling of the carrier on firing must be carefully controlled. Control of swelling automatically means control of explosive weight in the shaped charge which, in turn, influences charge performance. Carrier swelling also depends upon the confinement pressure at the level being perforated, which imposes a hydrostatic pressure-depth limitation. Burr interference on the wall of the carrier, resulting from passage of the jet through the carrier wall, must be eliminated by suitable design. Clearly then, a satisfactory shaped-charge gun design for slim-casing operations represents a fine balance between carrier swelling, hydrostatic pressure, explosive weight and charge performance. Additionally, to lend itself to directional perforating, the gun design must provide a positive locking mechanism for individual charges within the gun carrier. This fixes charge orientation within the carrier and prevents

By I. H. Van Horn

IN the development of the incandescent electric lamp one aim of the investigators has been to establish the fundamentals of lamp design, so that the performance of any new lamp may be accurately predicted. The study of the temperature relations in lamps has done much toward establishing these fundamentals. Fig. 1 gives the typical FIG. 1.-ARRANGEMENT OF PARTS IN MAZDA B AND MAZDA C LAMPS. arrangement of the lamp parts in both the Mazda B (vacuum) and Mazda C (gas-filled) lamps. The outstanding differences are the filament form and the bulb shape. The ideal lamp is one in which the filament operates at a uniform temperature throughout its length. In practice, it is necessary to disturb this uniformity by the introduction of supports and terminals. The amount of cooling at the supports and terminals affects the over-all efficiency of the filament as a light producer. The life of the lamp is ordinarily proportional to the maximum and not to the average filament temperature. The Holborn-Kurlbaum type of optical pyrometer has

Jan 9, 1919

By J. L. Lytton

The flow-stress recovery of high-purity aluminurn following a 10 pct tensile prestrain was studied in terms of a fractional flow-stress recovery parameter fr. The flow-stress recovery behavior was related to the dislocation arrangements using transmissiort electron rnicvoscopy. During recovery at 120° and 160°C, nearly stable strength levels were attained, the strength level for 120°C recovery being greater than that for 160°C. This stabilization of flow stress was related to the formation of meta-stable dislocation networks bounding nearly perfect cells. Both network formation and the annealing of dislocation loops were found to be recovery mechanisms, and the stronger metastable strength level joy 120°C recovery was related to a smaller average cell size. Analysis of the networks was consistent with the reaction of sets of dislocations with a/2 (110) Burgers vector to give product Burgers DURING isothermal annealing of cold-worked metals, a degree of softening occurs without re-crystallization, and the processes responsible for this change are termed recovery processes. During recovery annealing, the dislocations generated during cold work become rearranged into low-energy configurations, and as much as 50 pct of the stored energy is released."' The relationship between this rearrangement of dislocations and mechanical behavior is of considerable importance, since the dislocation substructures formed during recovery provide a significant degree of low-temperature strength3j4 and can favorably alter the course of primary creep at high temperatures.4 The purpose of the present study was to relate the flow-stress recovery behavior of high-purity aluminum to the substructural modifications that occur. Electron transmission microscopy was therefore employed for direct observation of dislocation substructures at various stages of recovery following 10 pct prestrain. Several investigators5-' have proposed that dislocations can become rearranged or lost during the preparation of thin foils. It was found early in the present study that the dislocation structures in the thicker regions of the foils changed in a systematic way during the course of recovery. Therefore, it is unlikely that substantial losses or rearrangements occurred during thinning. This point will be discussed in more detail later. The results of various investigators indicate that recovery processes in fcc metals can result in release of 50 pct or more of the total energy stored in the as-prestrained metal, this percentage decreasing with increasing prestrain.' Alloying elements or impurities tend to increase this percentage. The release of stored energy of fcc metals during recovery appears to occur by 1) annealing of point defects if the deformation occurred at sufficiently low temperaturesg and 2) rearrangement of dislocations into low-energy Configurations.1,2In bcc metals, the annealing of dislocation loops has also been observed during recovery after prestrain,10-12 and it has been proposed that this is a recovery mechanism for unidirectionally strained fcc metals.' The density of dislocations in bcc metals has not been observed to decrease appreciably during recovery,10 although the formation of regular dislocation networks has been observed. has shown that the formation of such networks can result in elimination of long-range stresses and can lead to significant release of stored energy without dislocation annihilation. It might thus be expected that network formation is a significant recovery mechanism in fcc metals, although extensive network formation has apparently not been reported in controlled recovery experiments. The formation of sub-boundaries in aluminum has been observed by various investigators13'17 during recovery studies of aluminum, but the structure of these boundaries was not resolved. In this regard, it is significant to note that Bailey and Hirsch,' using transmission electron microscopy, detected no network or sub-boundary formation during recovery of 99.99 pct Ag. Furthermore, Clarebrough et al.2 found no such rearrangements during recovery of copper. EXPERIMENTAL PROCEDURE The high-purity aluminum used in this investigation was obtained in the form of 0.125-in.-thick sheet. Spectrographic analysis revealed that the sheet was 99.995 pct A1 with the following weight-percent impurities: 0.001 Cu, 0.002 Fe, 0.001 Si, and 0.0004 Mg. The as-received sheet was in the heavily cold-rolled condition. The as-received sheet was cold-rolled at room temperature to 0.040-in.-thick sheet in the longitudinal direction, which was the original rolling

Jan 1, 1965

By E. J. Roberts

Hydrometallurgical operations and many processes in the chemical industry require the separation of dissolved material from solids. One of the decisions which has to be made in designing a plant for such an operation is how this separation shall be accomplished. It is the purpose of this paper to set forth the general principles involved in such separations in order that the optimum flowsheet and equipment may be selected. Countercurrent Decantation with thickeners, or C.C.D. as it is generally known, is, of course, only one way of separating dissolved material from undis-solved. Other unit operations such as Countercurrent Filtration (C.C.F.) and Countercurrent Classification (C.C.C.) are widely used. The same principles may also be applied to centrifugally assisted decantation, as with nozzle or solid bowl type centrifugals, and to separations using screens, either gravity or centrifugal type. Another form of countercurrent washing applicable to granular materials is practiced in continuous ion exchange operations. All of these operations depend on two basic principles, or combinations of these principles. In C.C.D. type operations the solids are concentrated into the smallest possible volume of liquor in each step and the resulting pulp then mixed with a more dilute liquor and recon cen trated, the liquors separated from the more dilute stages being advanced to dilute the more concentrated liquor in a previous solids concentrate, as is shown in Fig. I. This will be termed the solids concentration-solution dilution principle, or, for short, solution dilution. countercurrent decantation- type circuits. The second principle used in washing solubles from solids is that of solids concentration-solution displacement. Here the solids are restrained from movement while wash solution is forced through the interstices in a counter-current fashion, as in Fig. 2. In the simplest application of this principle, once the "cake" has been formed, it is not disturbed until the operation is completed. In continuous filters, the cake is merely moved under the successive washes and the displaced filtrates removed as in Fig. 4. Often, however, after one or two displacement washes, a repulping step is introduced, the cake reformed and washed again. This procedure brings the solution dilution principle into play as well as the solution displacement principle. Merely thickening ahead of filtration, which is often operationally advantageous, does not hybridize he circuit. It still can be a pure solution displacement operation from the washing

Jan 1, 1961

By W. J. Kroll

Jan 1, 1960

By E. B. Johnson

Cleveland-Cliffs lron Co., which operates Marquette lron Mining Co.'s Republic mine, conducted a test whereby 35,000 tons of self-fluxed pellets were produced in the grate-kiln system from specular hematite flotation concentrates. A brief description of the pelletizing plant is presented along with pertinent operating details. Date is included which compare operating conditions and the chemical and physical properties of the green and fired pellets for the self-fluxing pelletizing test with the normal acid pelletizing operation. The success of self-fluxed sinter in enhancing the operation of the blast furnace during the past few years has reasonably led to the assumption that the use of self-fluxed pellets might result in even greater furnace efficiencies. A great share of development work in agglomeration has been directed towards techniques related to the production of self-fluxed pellets, but only a limited tonnage of self-fluxed pellets had been produced on a commercial scale until this past year when The Cleveland-Cliffs Iron Co. produced 35,000 tons of such pellets by the grate kiln system at the Republic mine during the period May 21-June 5, 1962. REPUBLIC'S GRATE-KILN PLANT The grate-kiln pelletizing process consists of four stages, namely: feed or balling circuit, traveling grate, rotary kiln and annular cooler (Fig. 1). The balling section is conventional and utilizes four 9x30-ft balling drums in closed circuit with 5x14-ft vibrating screens having 3/8-in. rod decks. The traveling grate is 12 ft wide by 126 ft long and has 14 windboxes — six in the drying section and eight in the preheat section. The rotary kiln is 15 ft ID shell and 114 ft long. The annular cooler is 40 ft in diameter and has 12 windboxes. The cooler is divided into two zones by a moveable curtain wall. The high temperature air from the first zone is used as secondary combustion air in the kiln. Normally the only heat supplied is through the burning of No. 6 oil in the single kiln burner. Hot gases pass counter to the pellet flow through the system. The exit gases from the kiln pass down draft through the preheat section through cyclones and are drawn through the drying bed prior to exiting via the stack. The temperatures are normally held within the following ranges: Kiln 2400-2445 °F Preheat 1850-1950°F Drying 480-520°F Exit gas 200°F Pellets 120°F The design capacity of the Republic mine grate-kiln system was 2500 Itpd. Sustained production in excess of 35% over design capacity has been achieved. No screening of the cooler product is practiced. PELLETIZING TEST CONDITIONS When a decision was made to proceed with a test at the Republic mine pelletizing plant to produce 35,000 tons of self-fluxed pellets, several potential failure factors had to be carefully considered. Research work on a batch and pilot plant scale indicated that the grate-kiln system at Republic would require some major changes in order to obtain optimum conditions. In many cases compromises were agreed upon as major equipment changes and revisions were not feasible. The pelletizing conditions which laboratory development tests revealed were required in order to insure successful production of self-fluxed pellets were: 1) Good mixing of limestone and concentrate and proper moisture control; 2) Higher gas flow rates in the preheat section than are normally used; 3) Higher preheat temperatures than normal; 4) Maximum kiln temperature 2350°F. There was just cause for concern about balling problems that might occur. Approximately 10% of dry pulverized limestone was to be added to the specular hematite concentrate just ahead of the Pekay mixers on the belt feeding the balling drum. Large scale

Jan 1, 1963

By Don K. Smith

The Reclamation Program for the Northern Zone of the Indus Plains in West Pakistan involves the construction of 30,000 irrigation wells to serve 20 million acres with an annual pumpage of nearly 40 million acre-ft. Detailed hydrologic studies indicated that mild steel would be satisfactory for casing; however, within two years after construction, about 10% of the wells began to fail due to encrustation and corrosion of the casing. A search to find a noncor-rosive substitute for the steel casing disclosed that only fiberglass-reinforced plastic pipe satisfied all requirements. The results of initial use of fiberglass have been highly satisfactory and have resulted in a lower over-all well cost. Advances in technology pomise further reduction in prices and improvement in performance. The northern zone of the Indus Basin comprises a vast area of essentially level land in West Pakistan which is irrigated by means of a complex system of canals that distribute more water to more land than any other irrigation system in the world. In spite of the development of this extensive irrigation system, production of food and fiber has not met the requirements of the country. The major reasons that crop production has not reached anticipated levels are the lack of adequate irrigation supplies and effective subsurface drainage. As a result, yields per acre are among the lowest in the world for areas where irrigation is practiced, and many thousands of acres of valuable crop land have been removed from production or seriously affected by salinity and waterlogging. To rectify the problems of irrigation supply and drainage the Government of Pakistan has undertaken a program of Salinity Control and Reclamation which is being administered by the Water and Power Development Authority. The Authority retained Tipton and Kalmbach, Inc., of Denver, Colo., as engineers for the program in the northern zone of the Indus Basin. This program consists of the construction of about 30,000 irrigation wells to provide drainage for waterlogged lands and full irrigation supplies, including leaching requirements, for all cultivated lands. The program will ultimately ensure the productivity of 20 million acres and involve an annual pumpage from groundwater storage of nearly 40 million acre-ft of

Jan 1, 1970

By A. C. Fieldner, W. A. Selvig

For purposes of coal classification it is desirable to know the composition and calorific value of the pure coal substance; that is, of the coal free from its ash-forming minerals. Two methods suggest themselves: (1) To free the coal from most of the ash-forming material previous to the analysis; and (2) to analyze the coal as received and calculate the analysis, with certain more or less arbitrary corrections, to the pure-coal basis. Calculation methods are obviously more apt to give correct results with low-ash than high-ash coals. With coals of unusually high ash it would appear preferable to remove, previous to the analysis, as much of the inorganic matter as possible, by float-and-sink or acid-treating methods. Effect of Ignition on Inorganic Constituents of Coal The need of corrections in calculating analysis to the pure-coal basis is due to the fact that the ash, as determined by ignition, is not the same, in either weight or composition, as the inorganic mineral matter in the coal. On ignition a number of changes occur in the coal such as loss of water of hydration of the shaly material, conversion of pyrite (FeS2) to ferric oxide (Fe203) with evolution of the sulfur as sulfur dioxide or possible fixation of more or less of the sulfur in the ash as calcium sulfate (CaSO4), and decomposition of calcite (CaC03) to calcium oxide (CaO). The amount of sulfur from pyrite which remains in the ash as calcium sulfate depends on the amount of calcite and pyrite in the coal. Certain coals high in both calcite and pyrite show relatively large amounts of sulfate sulfur in the coal ash. The determination of total carbon and hydrogen in coal includes, besides the organic carbon and hydrogen, the carbon of inorganic carbonates such as calcite, and the hydrogen of the water of composition of some of the ash-forming minerals. For detailed discussion of corrections proposed for calculations of coal analyses to the " pure "

Jan 1, 1930

By P. van Meurs, C. van der Poel

From observations of the linear displacement of oil by water from a porous medium as visualized in transparent models, new insight into the mechanism of vircous fingering, as occurring in the case of unfavorable oil-water viscosity ratios, has been obtained. A mathematical description of the observed phenomena leads to formulas. expressing both oil production and pressure drop across the formation as a func-tion of cumulative water injection with the oil-water viscosity ratio as a parameter. Theoretical results are compared with those obtained from scaled laboratory experiments in sand-filled rubes in which water was injected at the one end and production was obtained from the other end. In the second part of the paper the same principles are used to calculate a more realistic production scheme in which production of oil and water is obtained from wells regularly distributed over the field. Results show satisfactory agreement with production data of an actual oil field. Application of the theory is extremely simple as only a limited number of readily available parameters have to be known and results are presented in an analytical form. INTRODUCTION When oil is displaced from a porous medium by water having a viscosity lower than the oil. the oil-water interface is essentially unstable and has the tendency to break up into what are called "fingers" or "streamers". This Viscous fingering has been noted before by Engelberts and Klinkenberg' and has recently been demonstrated in transparent models by van Meurs-. It is highly questionable whether it is at all possible to perform relative permeability measurements In the laboratory reproducing the same distribution of water and oil in the cores as Present in practice. Therefore, we based our descriptive theory on an idealized model which was "tailored" to the fingering mechanism as observed in transparent models under scaled conditions. This approach was the more attractive, as a highly simplified model had already yielded an adequate description of the process. Though we are aware our theoretical approach can be extended in several ways, it is given here in its simplest form to explain the fundamental principles and to avoid complicated formulas. SIMPLEST CASE OF A LINEAR DRIVE Observations and Theoretical Model In Fig. 1 a series of photographs shows how water penetrates into a formation saturated with an oil which is considerably more viscous than the water. The technique for obtaining these photographs, using transparent models, has already been described?. The fingers can be clearly observed and are seen to be mainly parallel to the flow direction. Note that the contours of these fingers are not smooth but show protrusions of water enclosing oil pockets.

By E. F. Adkins, R. W. Douglas

The variation of the spectral emissivity of osmium and ruthenium with temperature can be expressed by the following relations: DURING a study of the sintering characteristics of osmium and ruthenium, discrepancies in the previously accepted melting points of the metals were noted. The melting temperatures had not been measured at the time of the work, but were estimated in the literature as 2700°C for osmium and 2450°C for ruthenium.' A recent investigation by Baird2 has shown the melting temperatures of osmium and ruthenium are 3000" and 2250° C, respectively. In the present work, osmium bars sintered at temperatures as high as 2900° C showed no evidence of melting, whereas ruthenium showed definite evidence of melting at temperatures as low as 2250°C. In view of the apparent discrepancies, the melting temperatures of both metals were determined. The spectral emissivities of both metals were determined as an aid to studies of the sintering characteristics of these metals. MATERIALS AND PROCEDURES The materials used in these studies were metal powders supplied by Englehard Industries, Inc., through the courtesy of The International Nickel Co. Analytical data from three laboratories, although not in complete agreement as to the purity of the material or the major impurity elements, indicated that the maximum impurity levels were 0.5 and 1.0 wt pct in osmium and ruthenium, respectively. The metal powders were pressed to 1/4 by 1/4 by 6-in. bars at 20Tsi using carbon tetrachloride as a lubricant. The pressed bars were presintered 1 hr at 1200°C after heating 1 hr at 400°C. The presintered densities of the several bars of the metals ranged from 65 to 80 pct of ideal density. Specimens were self-resistance heated in a vacuum sintering bell. Temperatures were measured with an L&N, disappearing filament optical pyrometer. True temperatures were read at the base of an 0.30-in.-diam, 0.150-in. deep hole drilled into the center of a presintered bar. Apparent temperatures were read from the surface of the bar adjacent to the hole. MELTING POINT DETERMINATION The melting temperature of the metals was determined as the temperature at which a slight additional increase in current through the specimen resulted in a reduced temperature at the base of the hole. The apparent reduction in temperature is a result of the liquid metal filling the hole, thus altering the black-body conditions. The melting points of osmium and ruthenium, based on three deter-

Jan 1, 1962

By H. Linder, W. H. Dennen

The graphitic carbon content of soils may be used to detect and delimit subsurface graphitic zones. Spectrographic measurement of carbon in C horizon soils from several areas in the northeastern United States shows good correlation with known graphitic bodies. Bodies of graphite and sulfides are readily located by electromagnetic prospecting methods, but these methods cannot generally discriminate between them. Usual practice, therefore, requires follow-up work on electrically anomalous areas by trenching, drilling, or soil sampling in order to determine the mineralogical nature of the conductor. The efficiency and cost of such follow-up is consequently an important factor in prospecting. The presence of buried sulfide deposits is often reflected in concentrations of metals in the superincumbent soil. Simple chemical tests for such metal concentrations have been developed and applied with considerable success. Bodies of graphite or mixtures of graphite and sulfides are, however, very common and a means whereby buried graphite could be detected by soil testing should provide valuable additional information in the search for ore sulfide and graphite deposits. Graphite is a notably stable substance and should persist in soil above graphite-rich horizons. Microscopic examination of soil samples high in carbon, however, failed to reveal any recognizable graphite fragments indicating a grain size in the clay range. Presumably such small particles would have some mobility in a soil by a translocation mechanism similar to that proposed for the movement of clay particles in a soil profile. Experimental data supports this idea since the boundary between background and anomalous soils carbon values is quite sharp, but the anomalous zone is slightly broader than the graphitic source rock. A simple spectrochemical technique for the determination of carbon in geological materials has been described by Dennen,1 and may be directly applied to soils. A modification of this technique which employs an arcing chamber through which nitrogen is passed is recommended to decrease contributions from atmospheric carbon dioxide. Tests indicate that soils over graphitic zones may be strongly enriched in carbon. The spectrochemical determination of carbon depends upon the formation of the cyanogen molecule (CN) from carbon in a sample and atmospheric nitrogen, under the high temperatures associated with a dc arc. Samples for analysis are dried, lumps broken, and screened. A small portion of the -100 mesh fraction is packed into a copper electrode and excited as the cathode of a dc arc. The band spectra of cyanogen are recorded photographically and the density of the bandhead CN 3883A is measured. The limit of detection of the method is about 0.01 pct C and its coefficient of variation is about 15 pct. Soils, of course, contain carbon in other forms than graphite, and the amount of interference from such sources was examined. The C horizon of several soils from Massachusetts, Maine, and Pennsylvania were found to have a carbon content of 0.3 to 0.5 pct by weight. This content is chiefly due to the presence of carbonates and vegetable matter in the sample and may be readily eliminated, or at least

Jan 1, 1961