Search Documents

Jan 5, 1951

Jan 3, 1951

Jan 7, 1951

Jan 11, 1950

By C. J. Fleisch, C. P. Clingerman

THE recent installation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. THE FURNACE PROPER A few of the characteristic points and dimensions of the furnace proper are: [Hearth diameter 26 ft. o in. Bosh diameter 29 ft. 1 3/4 in. Stock-line diameter 20 ft. o in. Large-bell diameter 114 ft. 8 in. Small-bell diameter 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed 94 ft. 4 in. Height of furnace from center of iron notch to main platform 105 ft. o in.] The furnace top is equipped with a McKee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. g in. in diameter, then through uptakes that are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. DUST CATCHER The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catcher is g ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is 50° with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas in-

Jan 1, 1943

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By B. B. Zavoico

During 1936 the Russian oil industry made very satisfactory progress and, while not all difficulties of organization have been ironed out, the country is now assured of a supply of petroleum products in sufficient quantities and of quality demanded by modern motor equipment. The year 1937 promises to better by a wide margin the good showing of 1936. The statistics given in this paper for the first time take into consideration the varying gravities of crude oils of the several Russian oil fields instead of using a flat conversion factor of 7 bbl. per metric ton. It was found from the detailed study that the generally used average conversion factor should be increased from 7 to 7.25 bbl. per metric ton, the figure varying, of course, with the gravity of oil in the individual fields. Crude-oil production during 1936 is estimated at 201,500,000 bbl. as compared with 182,970,000 bbl. produced in 1935, an increase of 9.4 per cent. The greatest increase was again recorded in the Baku district, which increased its production by 10.9 per cent, from 141,257,000 bbl. in 1935 to 158,300,000 in 1936. Grozny district maintained its production at a level of about 23,000,000 bbl., but its old fields continued to decline and production was sustained by the development of newer fields. A great advance was made in drilling speeds and the total footage in 1936 reached 6,694,200 ft. as compared with 4,926,600 ft. drilled in 1935, an increase of 26.4 per cent. In older deep fields, producers were being completed at over 8000 ft.—a great depth for Russian drillers but two years ago. Several major discoveries were made in 1936. Northeast Caucasus.—Izberbash, east from Grozny and on the Caspian Sea, was the outstanding discovery, the initial production of the discovery well being around 3000 bbl. per day from about 5000 ft. The importance of the field is due to the large area of the structure, half of which, however, is under the sea, and also to its strategic location on the shores of the Caspian and near a trunk pipe line to the Grozny refining center. An active development program is being pursued in Izberbash and its 1937 production quota is set at 7,500,000 bbl. Achi-Su field, near Izberbash, also discovered during 1936, while not as prolific as Izberbash, is thought to cover a very large area and the small

Jan 1, 1937

By T. D. Jones

MUCH the same story can be told for the lead industry for the year 1945 as for the three previous years. In response to inquiries as to new developments, invariably the answer has been, "No new developments-our men either too busy with the man-power problem or trying to get production out." Time and efforts of industry have been concentrated for the most part on war or readjustment problems. Now that V-E and V-1 day have passed, the lead industry can justly be proud of its record in World War II. As in previous wars, lead played an important role and one of its most spectacular uses was in the production of the atomic bomb. We read that the part lead played was rather obscure, but as a protective agent, lead played a most significant role. "Since the materials in the Pile Plant are intensely radioactive, all storage and handling must be done behind thick concrete walls or lead shields. The material is never seen and all operations are auto matically controlled by a foolproof remote control system especially designed for this purpose." (Chews. & Met., Sept. 1945.) When our armies invaded the European theater of war and made a landing on Normandy beach, gasoline and oil for the motive power were furnished through miles of armored lead pipe. This amaz-

Jan 1, 1946

By A. W. McReynolds

One characteristic of plastic deformation which distinguishes it from elastic strain is the essential inhomo-geneity of plastic strains. Elastic strain varies continuously through a material, and average relative displacements of initially adjacent atoms are only small fractions of their initial spacing, (strains of the order of 0.01 or less). On the other hand, plastic flow corresponds to the appearance of discontinuities in strain of the lattice, such as dislocations or slip bands, where local strain, on an atomic scale, is several orders of magnitude higher. These discontinuities are visible on a microscopic scale as the familiar slip lines (Fig 1). In spite of this obvious microscopic inhomogeneity, however, macroscopic measurements almost invariably show a smooth curve of stress vs. strain (Fig 2b) even if measurements of linear strains be made to an accuracy of one part in 107. This macroscopic homogeneity of strain indicates that the discontinuities in strain on slip planes occur in increments too small or too slow to be recorded individually, and further that they occur sufficiently independent of one another so that the small increments add at random to a smooth stress-strain curve. The present paper describes observations of plastic strain in aluminum of commercial purity and in high purity Al-Cu alloys, where there exists a strong coupling between slip in various regions of the specimen such that once initiated it spreads rapidly through a large volume. The total effect is that of relatively large, rapid, and regularly spaced steps of strain followed by periods of only elastic strain. Fig 2a illustrates the type of "stair-step" stress-strain curve which results. The properties of this cooperative slip phenomenon will be described further in the section on results: in par- ticular it will be shown that each step corresponds to the propagation of a wave of plastic deformation through the specimen. Some interpretations of the mechanism by which it occurs will be made in the following section. Although the type of plastic wave phenomena to be described has not previously been reported, there are numerous cases of related effects in the plastic yielding of metals: YIELD POINT PHENOMENA The most familiar of such effects is the "yield point" observed in low carbon steels, brass, duralurninum, and the like. It consists in the sudden termination of the elastic portion of the stress-strain curve by a large plastic strain. Since the usual tensile machine is such that yielding of the specimen relieves the load, the resulting curve is as shown in Fig 3. As the strain continues, deformation occurs at a lower stress for some time, then follows a rising curve, but with no further sudden yielding. This effect has been observed in brass by Sachs and Shojil and later by many others. Edwards, Phillips and Jones2 made extensive studies of the effect in steel, and of the role of various alloying elements. Although there seems to be fairly clear evidence that the yield point is caused by a hardening of the material by precipitation of impurities, no satisfactory explanation for the sudden yielding has been given. Winlock and Leiter3 have shown that the strain. level of the upper yield point depends strongly on the rate of loading, the yield point increasing by almost a fac- tor of two as the strain rate goes from 0.002 in. per in. per min. to 4.4 in. per in. per min. This effect would seem to imply an incubation period before yielding is initiated at a certain stress. On the other hand, by going to very slow loading rates, Edwards, Phillips and Jones2 showed that the yield point does not become lower and eventually disappear as might be expected, but, on the contrary, begins to rise at loading rates below about 25 Ib per in. per min. becoming much higher than at rapid loading rates. STRAIN AGING If, instead of continuing straining of a specimen after occurrence of a yield point, the load is removed and the specimen aged, resumption of the test results in occurrence of another yield point as shown by the dotted curve of Fig 3. The new yield stress is generally higher than the previous maximum applied stress. This hardening of the material by straining and subsequent aging is undoubtedly related to quench age-hardening resulting from the aging of a specimen quenched from high temperature. Since neither effect is observed in pure metals, it is generally accepted that quench-aging in all cases is the result of hardening by precipitation of a supersaturated alloying element, and that strain-aging is probably a similar precipitation, accelerated by disruptions of the lattice by previous strain. Pfeil4 has shown that strain-aging does not occur in iron from which all of the carbon has been removed, but that only a very small carbon content, around 0.003 pct, is necessary to cause strain-aging. In accord with this observation is recent work by Dijkstra5 in this laboratory showing that the solubility limit of carbon in iron is extremely low, less than 0.001 pct at 400°C. Edwards, Phillips and Jones2 have shown that the strain-aging effect is also removed by the addition of small quantities of elements such as Mo, Mn, Ti, and the like, which readily form carbides. Their results demonstrate the

Jan 1, 1950

By Robert L. Llewellyn

Preparation of coal begins at the face in underground mines or in the pit with surface mines. Impurities in raw coal can be in the seam itself or in extraneous material taken in mining from the roof or bottom. Raw coal is prepared only to the extent that is necessary to make the product salable. Over 60% of all coal production is processed to some extent in cleaning plants. For underground mines the proportion cleaned is 72% as compared to 42% from surface and 15% from auger mines. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only as necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent and only incidently with mines shipping raw run-of-mine coal crushed to a top size of, usually, 2 to 4 in., with little, if any, other treatment. ECONOMICS OF COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-rang planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and atomic energy. Cod prices for power plants are still on a Btu (British thermal unit) basis but with more emphasis on sulfur content. For metallurgical coal, the lower and medium volatile coals are in demand and the price rises, generally, as the volatile percentage is lower. Moisture affects the Btu value of coal almost the same as ash content, but dusty conditions during loading and unloading are no longer accept-

Jan 1, 1973

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral, rutile. United States consumption of titanium dioxide for these applications in 1973 was as follows: pigments, 891,000 st; titanium metal, 40,000 st (=24,000 st metal) ; and welding rod coatings, 10,000 st. The only commercially important titanium ore minerals at the present time are ilmenite, and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) states that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlines the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: "Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during the time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, Va., and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, Fla., for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for lowgrade sands, led to a return of activities in this area. The large deposits near Tahawus, N.Y., were brought into production in 1942 by National Lead Co. (now N L Industries Inc.), and by 1949 this company was the lead¬ing producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec." The beginning of the modern titanium metal industry was in 1948, when E. I. du Pont de Nemours & Co. produced the first metal. U.S. Bureau of Mines reports, which gave details of the Kroll process, together with the attractive properties of the metal for

Jan 1, 1975

By Alan Stanley

The MacIntyre Development of the National Lead Co. is located at Tahawus, N. Y. The operations involve the mining and concentrating of a titaniferous iron ore to produce an ilmenite concentrate and a magnetite concentrate. Construction of the MacIntyre plant was commenced during the summer of 1941, when world conditions threatened to cut off the supply of Indian ilmenite. An open pit mining operation was developed and the crushing and milling equipment put in operation in July 1942. A general description of the operation was given in the Adirondack Issue of Mining and Metallurgy for November 1943. The metallurgy of the mill operation was described by Mr. Frank R. Milliken,* Plant Manager, National Lead Company, MacIntyre Development, and presented at the AIME New York Meeting, February 1948.

Jan 1, 1949

[†AARONSON, ALFRED E., Vice-Pres., Mid-Co. Petroleum Co., Mid-Co. Bldg. Tulsa, Okla. '18 ABADIE, EMILE R., Min. Engr Address wanted. '76 ¦ABADILLA, QUIRICO A. Geol. Dept. Cia. Mexicans de Petroleo "El Aguila," S. A., Edifico "El Aguila," Esq., Calles Aurora y Comercio,] [ ]

Jan 1, 1925

By David Cole

THE New Cornelia Copper Co. is mining and treating a 'monzonite " porphyry" copper deposit that is all hard rock. The oxidized surface shell, which constitutes the leachable part of the orebody, is measurably more resistent to crushing and comminution processes than is the underlying sulfide portion. The siliceous ribs running through the whole orebody are harder to crush than the main mass and there is no soft crumbly material to furnish the large volume of primary fines that features the crusher feeds of most other porphyry properties. New Cornelia ore reaches the primary crushers with a greater. proportion of large 'pieces. When the New Cornelia company first equipped its 'property, it used the following machines and flow , scheme to reduce the ore to leaching size:

Jan 1, 1925

By Frederic E. Carter

THERE have been many attempts to prove that platinum was known to the ancients, but since no traces of the metal have been found in the relics of early times, it must be concluded that it was not known to them. As far as records go, it was actually first discovered in the 16th century in a Spanish mine on the Pinto River in South America; from which source it received its name of Platina del Pinto (little silver from the Pinto). It was more or less of a rarity and was a subject of interest to a few chemists only, until the year 1822 when the metal was first discovered in Russia. In 1819 there were noticed in the washings of the gold sands of the southern part of the Ural Mountains, grains of a heavy white substance, but it was not until three years later that this substance was found to contain platinum. While at first the amounts of platinum brought from the Urals were meager, prospecting soon disclosed rich deposits extending over a considerable area, and nuggets from 10 to 20 lb. were by no means rare. This discovery assured to chemists an ample supply of platinum for their crucibles, etc. The ore is now found in various parts of the world but the richest deposits are still found in the Ural Mountains. The platinum of commerce is obtained entirely from alluvial deposits at depths varying from 6 to 40 ft. The sand and gravel of former river beds are subjected to a series of screenings and washings to effect the separation of the ore. Actually, probably all gold-bearing gravel beds of the world contain platinum, and it is more than likely that large quantities of platinum ore have been thrown away with the black sand washings from gold placer deposits. This is especially true of the alluvial deposits of the Pacific Coast in California and Oregon. Platinum ore is usually found in the form of rounded or flattened grains of "sand," and occasionally in irregular lumps of the size of peas. Large nuggets are very rare. The ore has a metallic luster and is distinguished by its steel gray color, but shows light gray streak when rubbed on a hard white surface; it has a high specific gravity, 16 to 19; is infusible in the hottest blast furnaces, and insoluble in any single acid. Platinum ore is a complex body consisting of the metal in combination with varying proportions of the other members of the platinum group; iridium,

Jan 1, 1928

By B. S. Old, E. R. Poor

PRODUCING more steel without major capital investment in new plants is one of the most perplexing difficulties which confront the nation's postwar steel industry. The lack of scrap at a reasonable price results in an especially heavy pressure being brought to bear on the pig-iron production facilities which consist of 245 blast furnaces scattered throughout the country but concentrated most heavily in the Pittsburgh-Chicago area. Present demands exceed the total optimum output of these existing blast-furnace plants. Management hesitates to authorize erection of new plants on a scale sufficient to satisfy 'the demand for pig iron for two main reasons: first, extensive building under the present high costs of construction would greatly increase . the over-all capital investment per ton of iron capacity; and, second, the amount of steel necessary for a major construction program would upset the already tight supply-demand situation. The answer to the problem would then seem to be the development and application of a method which would increase the capacity of existing blast furnaces with a minimum of alterations and expense. Experiments consisting of operating a blast furnace at higher-than-normal top pressures, as proposed by Arthur D. Little, Inc., were carried out by the Republic Steel Corp. initially during World War II, and much more extensively during the past twenty months. The results of the Republics trials indicate that pressure blowing is a solution to the problem of increasing pig-iron capacity without necessitating major changes to existing equipment.

Jan 1, 1948

By G. E. Warner

This paper presents a review and analysis of a highly stratified Burbank sand waterflooding project in Osage County, Okla. Permeability values in this reservoir range from less than 0.1 md to nearly 3 darcys, and 90 percent of the permeability capacity is contained in approximately 26 percent of the reservoir volume. To date, the project has recovered 103 bbl/flood-acre-ft since waterflood initiation, which represents 50 percent of the total preflood cumulative and 12 percent of the original stock-tank oil in place (OSTOIP). The outstanding feature of this project has been the economical recovery of a sizable quantity of oil at water-oil ratios higher than those normally considered prohibitive. Nearly 70 percent of the recovery to date has been achieved at water-cut values greater than 95 percent. An ultimate waterflood recovery of 138 bbl/flood-acre-ft, or 67 percent of the preflood recovery and 16 percent of the OSTOIP, is predicted. The ultimate primary and secondary recovery will be 302 bbl/acre-ft and approximutely 40 percent of the OSTOIP. The actual performance is compared with the predicted performance by both the Stiles and the Dykstra-Parsons methods, and applicabiliry of these methods to this particular reservoir is evaluated. The performance of this project indicafes highly stratified reservoirs can be successfully and economically waterflooded when either reservoir or economic conditions preclude the use of mechanical and chemical means of mdbility control. Introduction The concept of the stratified reservoir has been used by reservoir engineers for many years to describe the vertical variations in permeability within a reservoir. Numerous techniques have been advanced to predict the expected waterflood performance of the stratified reservoir, and in most cases they prove reasonably accurate. The advisability of undertaking a prospective waterflooding project is determined, based on these predictions. This paper presents a review of a waterflood project in a highly stratified reservoir that normally would be considered a marginal prospect, at best, when evaluated with any prediction technique properly adjusted for reservoir conditions. This kind of project can be successful if the predictions are used to design a waterflooding system capable of economically recovering an oil cut of 1 to 2 percent. Experience gained in the early stages of the project's development was profitably applied in the later development of the entire reservoir and could prove beneficial to other projects with similar reservoir stratification or fracture characteristics. The East Burbank pool waterflooding operations have been developed in three separate stages, each of which has been a separate project: Mid-Burbank Unit, Flood A, and Stanley Waterflood. When referred to collectively, these projects will be called the Composite Project. The Skelly Oil Co.'s Barber lease — the only portion of the pool not included in the three projects — is operated as a separate facility with a cooperative injection-well agreement. It contains less than 80 productive acres and would not significantly affect the over-all performance picture.

Jan 1, 1969

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922