Search Documents

By Jan Visman, S. J. Aresco

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all the layers of coal and impurities found in the seam as well as portions of the stratas above and below the coal seam. The preparation plant is the device to size, crush, and/or remove impurities so the coal may be shipped as a salable product. Sampling may be needed at many stages in the preparation process. Although this chapter is primarily concerned with sampling in connection with preparation processes, the principles apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1) To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained, or monitoring raw coal delivered to the plant. 2) To check the performance of various operating units in the plant, either by float. and sink tests or chemical analyses. 3) To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in US Bureau of Mines (USBM) publications by J. A. Holmes,l G. S. Pope,2 and A. C. Fieldner.3 The American Society for Testing and Materials (ASTM) more or less adopted the methods proposed by USBM in their Standard D-21-1916 and it remained a standard for many years. Briefly, this standard called for a 500 lb (227 kg) sample for coals less than 94 in. (19 mm) in size and a 1000 lb (454 kg) sample for all coals over 94 in. (19 mm) in size. No mention was made of increments, but there was an instruction that the sample should spread over the coal

Jan 1, 1979

DAVID WHITE,* Washington, D. C.-This paper is very timely since the Philippine Islands are presumably open to the enterprise of the American driller, whereas much of the territory in that part of the world is closed to us. The United States has ambitious plans for the operation of a great merchant marine, which is to be oil burning in the main, and it takes but a glance at the world map to see the strategic advantage of oil supplies in the Philippines for such marine operations. It is a little difficult to understand why more attention has not been given to the Philippines, in spite of the difficulties attending development in these islands. A number of American oil companies are, I believe, at the present moment taking an interest in the possibilities of the Philippines. Important factors in the formulation of opinion regarding the importance of the oil deposits of the Philippines, as brought out by Mr. Pratt,1 are the point of view and the breadth of experience of the examining geologist. The average oil geologist, whose experience has been mainly in the Appalachian region, the Mid-continent, or Louisiana, or possibly even in California, on seeing the narrowness of the basins, the closeness of the folding, and the presence of igneous rocks here and there, would be likely to draw unfavorable conclusions as to the possibilities of the Philippine Islands. Geologists visiting that region should be familiar with the geological conditions of oil occurrence in Japan, Formosa, the East Indies, or in the Baku district, and their conclusions should be formulated with the knowledge and understanding of the occurrence of oil in those regions rather than in the United States.

Jan 8, 1920

By B. S. Butler

Introduction. THE New London copper mine, about 81, miles east of Frederick, Md., was visited by the Writers for a few hours in the spring of 1909 and the following brief notes on ore specimens collected are presented as a contribution to studies in chalcocite ores. For certain data on the structural and areal geology of this portion of Maryland the writers are under obligation to the unpublished notes and maps of Arthur Keith. The detailed study of the ores is the work of B. S. Butler. The deposit here discussed has many similarities to those of the Virginia district of Virginia and North Carolina, which have been described y Graton1 and Laney2, except that in the deposits of the New London mine chalcocite is by far the most important ore mineral, while in the Virginia deposits bornite is commonly-the most important sulphide. In the New London occurrence calcite is the most important gangue mineral.

Jan 7, 1914

By Oscar E. Harder

THE TERM "physical metallurgy' is used in the title of this lecture in preference to "metallography ?because the former has a broader meaning with most audiences, some people thinking of the latter as being limited to work with the microscope. This distinction, how- ever, has not been held by the out- standing workers in the field of metallography, such as the late Professor Sauveur. In the broadest sense metallography is essentially the same as physical metallurgy. The American Society for Testing Materials has adopted-the following definition: "Metallography is that branch of science which relates to the constitution and structure, and their relation to the properties of metals and alloys." This definition might be improved by adding after "properties" -"and their industrial and scientific uses." Metallography has also been defined as the science of metals and alloys. Physical metallurgy is to be distinguished from process metallurgy in that the latter relates particularly to the production of metals from the ores.

Jan 1, 1940

By G. Pizzi, G. M. Ciucci, G. L. Chierici

The use of the material balance equation to estimate the volume of hydrocarbons originally present in a reservoir, whose producing mechanism is partly due to water drive, has been discussed in the literature by several authors. There is no general agreement upon the possibility of obtaining reliable results by this method. Gas reservoirs in contact with an active aquifer are considered in this paper. Theoretical considerations based on the cybernetic principle of uncertainty (which states that the internal structure of a system cannot be uniquely determined from its observed external behavior) lead to the conclusion that the volume of gas originally present in a reservoir of this type cannot be uniquely determined from its past history. The range of values which encompasses the actual value of the reserves varies from case to case and must be determined by either numerical or analogical methods. Results obtained for six gas fields are reported. All these fields were produced with small fluctuations in their production rates, as is common practice for gas reservoirs; no gas storage fields were considered. Results obtained show that reserves values in a range of 1 to 2, associated with appropriate aquifers, allow the matching of the reservoir past history with mean-square deviations less than the experimental errors involved in pressure and produclion measurements. Similar results have been found in several other partial water drive gas reservoirs. From these results it is concluded that gas reserves cannot be uniquely determined from the past performance of partial water drive reservoirs, at least in cases where the reservoir has been submitted to small fluctuations in the production rates, and pressure data of normal accuracy are available. INTRODUCTION A number of authors have analyzed the problem of estimating the reserves originally present in a partial water drive reservoir from its past pressure-production performance. Literature which deals with this subject can be grouped, according to their conclusions, as follows. 1. A reliable value for the reserves can be obtained even if reservoir data (pressure and cumulative production) are affected by errors within the normal range.'-' 2. A reliable value for the reserves can be obtained only if reservoir data are very accurate'- or if past production performance has been subjected to abrupt variations in the production rate."' 3. No unique value for the reserves can be obtained from reservoir past production performance. This conclusion has been based upon theoretical considerations" and verified in several field cases. The purpose of this paper, which deals only with partial water drive gas reservoirs, is to test the above conclusions against actual field cases. Some theoretical considerations on this problem are also presented. THEORETICAL CONSIDERATIONS As the behavior of a gas reservoir communicating with an aquifer depends on both the aquifer and the reservoir characteristics, the physical system to be studied is the combined gas reservoir plus aquifer. The information which is available for studying the performance of such a system is the well production rates and bottom-hole pressures, all given as functions of time. The external behavior of the reservoir-aquifer system is therefore described by 2n input variables (Gp, Wp,) and n output variables (p,), n being the number of wells in the reservoir. In reservoir engineering it is common practice to consider the reservoir as a whole, disregarding the internal distribution of pressures and of producing wells. This practice is equivalent to substituting the above multi-variable system with a single-variable system, where the average reservoir pressure is the only output variable and the cumulative production G,(t) and W,(t) are the input variables. The internal structure of such a system, defined by initial gas reserves G, aquifer shape and dimensions, boundary conditions and petrophysical parameters distribution throughout the aquifer, is unknown. Therefore, from a cybernetic point of view the system is a "black-box It has been demonstrated" that for a blackbox the indetermination principle holds. Accordingly, the number of different internal structures (or set of parameters) which can account for the observed external behavior is infinite. As a consequence, the initial reserves cannot be uniquely determined from the reservoir past performance. When W,(t) is known, the determination of G from

By Joe B. Alford

Jan 1, 1971

By G. R. Love, M. L. Picklesirner

THE use of color adds a new beauty, power, and versatility to metallography. This has been amply demonstrated in a number of public exhibits and on the walls of corporate, government, and university metallographic laboratories around the world. Indeed, in a number of cases, the color not only is of esthetic value but is scientifically essential to the competent examination of particular samples and systems. Optical strain analysis,' determination of true grain size in U-A1 alloys: phase identification in Nb-base alloys,3 analysis of transformation rates in heat-treated Nb-Zr alloys,4 measurement of solidification segregation in cast Nb-Zr alloys,' study of the intermediate phases in Nb/Sn diffusion couples,6 investigation of the oxidation kinetics at various surface orientations in single crystals,7'8 and a number of other research efforts9'10 would have been vastly more difficult without the extra clarity and distinction introduced by color—either the colors resulting from particular polarized light techniques or the interference colors obtained by oxidation. It is unfortunate that the beauty of colored micro-structures cannot be shared more widely, but the economics of publishing a technical magazine apparently prohibits color plates except under extraordinary circumstances. It is doubly unfortunate that no convenient, general method exists for communicating the information available in colored microstructures to the scientific community. True, in some instances the color changes observed are dramatic enough that direct black and white photography is adequate. In photoelastic stress analysis, several orders of interference fringes may be produced and it is frequently desirable to suppress the color effects (use monochromatic light) to simplify interpretation. On the other hand, relatively minute color variations may be readily detectable by eye, be of considerable assistance in interpreting a structure, and yet be enormously difficult to reduce to an unambiguous black and white print. In order to illustrate a possible compromise or solution to the above problems, we wish to show three black and white photographs of the same region of an Nb/Sn diffusion couple whose interpretation depends heavily upon use of color techniques. These micro-structures were obtained from a section through a rod consisting of commercial-purity niobium tubing filled with 99.995 pct Sn (melt-filled in 10"6 Torr vacuum). The composite rod, measuring 500 mm long, was bent into a hairpin shape and inserted into water-cooled copper grips in a vacuum high-temperature furnace. The rod was outgassed for 2 hr at a furnace temperature of 800°C and was further heated by self-resistance using a 2.2-kva ac power supply. The rod was raised to 1910°C over a 4+-hr period, held for 15 min, slow-cooled to 1500°C over a -hr period, and free-cooled to room temperature (all temperatures were measured with W5Re/W26Re thermocouple). Throughout the heat treatment the ambient pressure was kept below 8 x lo-' Torr. Metallographic preparation of the sample was completely conventional except that it was necessary to extend the grinding steps to remove damage in the brittle NbsSn phase introduced by sectioning. No satisfactory chemical or electrochemical etch has been found for these diffusion couples; of those which have been tried, any that attack the niobium-rich phases at all attack the tin-rich phases disastrously. However, the final polishing steps did produce a slight relief effect and this, coupled with anodizing, yielded excellent clarity in the microstructures for direct observation. The anodizing voltage was chosen to give maximum change in color per unit change in composition. In this case, indeed normally, this maximum sensitivity occurred in the blue-to-red color range. The pure niobium tube wall anodized to a relatively bright blue

Jan 1, 1967

By Arthur Notman

THE mineral industries in this country have now had about a year of national planning. Al. though the period is short, the volume of activity and legislation designed to make that planning effective has been nothing short of enormous. Those who have been privileged to see and study a few of the codes to regulate our mineral industry, such as those for oil, coal, steel, and copper, are driven to the conclusion that nothing was really known about the proper way to conduct those industries in this country prior to June, 1933; or if anything was known, nobody in actual practice made use of that knowledge. And yet those industries, in days gone by, helped to make this country the most prosperous in the world, and to maintain a standard of living even today higher than that of any other country. Without wishing to assume any first-hand knowledge of the Russian standard of living, I must confess that the evidence seems to indicate that even with dictatorial authority, national planning encounters unexpected difficulties. Perhaps what really wants

Jan 1, 1935

By Ernest R. Lilley

THOSE acquainted with the fundamental differences between the, educational .systems of Great Britain and. the United States would hardly expect .the training of men for the petroleum industry to proceed along the same lines- in the two countries. The youth entering an English university is, except in the case of-the student from some of the British colonies or from foreign countries, almost invariably a product of the English "public school." This is in no sense comparable .with the American public school. It is a private institution, frequently of considerable age and heavily endowed. In many aspects it seems to be comparable with the American preparatory school. Yet to some extent its activities remind one of the first years of the undergraduate: course in the American college. Certainly it takes to-itself many of the social, functions of the American college.

Jan 1, 1931

By C. H. Brehaut, W. N. Taylor, R. S. Douglas, H. A. Shannon

THE name for this new method of mining is derived from a composition of Horizontal, Radial, Diamond, and the drilling is from raises. This method, worked out at Copper Mountain, B.C., is believed to be distinct in many features from other known methods. GEOLOGY The ore deposits of Copper Mountain are related to the Copper Mountain stock, which is an ideal example of the magmatic differentiation in that it grades from a basic gabbro at the border to an almost pure orthoclase-pegmatite core. The "contact" ore bodies lie along the contact of the gabbro and an older complex of volcanics and sediment termed the "Wolfe Creek" formation. These older rocks, collectively referred to as greenstone, had been fractured prior to the intrusion of the stock and were highly metamorphosed during the intrusion. The "outlying" ore bodies are somewhat different in character, though a similar structural pattern prevails. It is believed that a deep-seated magma of which the Copper Mountain stock is a part has given off solutions that caused a partial granitization of some of the volcanics. Mining problems are caused further by the presence of a series of soft barren dikes intersecting a great many of the ore bodies, which are about 30 ft. wide, strike north-south, and dip at a high angle to the east; and are further increased by the presence of four major faults, with a great many minor faults running at acute angles from them. Fault zones average 8 ft. in width, and consist of gouge and breccia. They strike northeast and dip steeply to the northwest. The faults cut through the ore zones and the dikes, and continue on into the gabbro. The general mine structure with two types of ore bodies, bounded by weak walls and intersected by several series of soft barren dikes and major faults, indicated that a method of mining should be devised that would remove the ore at low cost with the least disturbance of the waste walls and dikes. THEORETICAL ESTIMATE OF STOPING WITH THE DIAMOND DRILL After consideration of various methods, the most suitable one appeared to be horizontal drilling to break the ore in a manner similar to shrinkage stoping. Drilling vertical holes or rings from a bench and breaking to an open slot was eliminated because the weak walls of ore, dike or waste would not permit this type of opening. It was then decided to drill either horizontal radial holes from a raise or parallel holes from a slot cut across the ore body. After discussion, the latter method was believed unsuitable, for the following reasons:

Jan 1, 1945

By Robert Livermore

IT has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored, or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the .underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining Co. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining Co. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently far from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, y means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities -of-ore, -and- made development- in certain

Jan 7, 1914

By Robert Livermore

It has been a noteworthy feature of the Cobalt camp, that many of the valuable ore deposits have been covered, wholly or in part, by small but usually deep lakes, such as Cobalt, Cart, and Peterson lakes, and with the subject of this article, Kerr lake. In the early days of the camp many water-covered areas, which have since been found to be valuable, were ignored or neglected by owners, or simply perfunctorily staked for water rights. Kerr lake is probably the evidence of a fault or sharp fold, having a general east and west strike, and containing a series of ore-bearing fissures, parallel generally to the strike, although having some notable exceptions to the general rule. On the north side of Kerr lake the formation is of diabase, while on the south side it is of Huronian slates and conglomerates. These Huronian measures extend out under the lake, dipping gently to the north to a lateral distance not yet definitely determined, owing to the lack of development under the deepest parts of the lake. Probably the contact between the diabase and Huronian or else between the former and the underlying Keewatin formation occurs somewhere near the center of the lake. Kerr lake originally covered 45 acres. Of this the Kerr Lake Mining CO. owned 12, the Drummond Mine, 7, and the Crown Reserve Mining CO. the remainder of 26 acres. Since the latter's property was originally entirely under water, it was necessary for the owners to make land for buildings and shaft room. Accordingly, in 1908, a trench was blasted out which deepened the outlet, and lowered the lake 8 ft. As many of the rich veins of the Crown Reserve and Kerr Lake companies were under water, mining was pursued under some disadvantages. Fortunately the rock is tight and solid, and mining has been done sufficiently fay from the surface to avoid unnecessary risk. Nevertheless, there was always danger of encountering open seams, through which too large a flow of water for comfortable working might come. Careful soundings were made over the veins, by means of steel-shod pipe, through mud and water to bedrock, but there was sometimes an element of uncertainty as to whether actual bedrock had been reached. Furthermore, the necessity of leaving safe backs between workings and lake tied up large quantities of ore, and made development in certain

Jan 1, 1915

By Kenneth K. Humphreys

INTRODUCTION What is automation? Why automate? Webster's New Collegiate Dictionary defines automation as "the automatically controlled operation of an apparatus, process, or system by mechanical or electronic devices that take the place of human organs of observation, effort, and decision." This definition gives an implied answer to the second question, "Why automate?" Automation, automatic control devices, and process control equipment receive their justification in supplementing or replacing manpower, which results in decreased operating costs. In the past, processes were operated with the minimum amount of instruments needed merely to guide operators. Processes were manually con- trolled by the operator on the basis of simple temperature, pressure, flow, and level indications on a panel. Today the tendency is to design a new plant to operate in a fully automatic manner according to a preset pro- gram utilizing a minimum of manpower. In addition to this direct cost reduction in manual labor, increased equipment capacity results from uniformity of flow and uniform control of process variables. This control eliminates or minimizes surges and permits equipment to be operated at or near its ultimate capacity and, for a given material throughput, permits the use of smaller process equipment. Automatic control, therefore, be it in the field of coal processing or in any industrial field, is simply a problem of economics. Control equipment is justified in terms of its contribution toward increasing productivity, increasing profit margins, or producing a new and salable product at a profit. Instruments and control devices can be divided into two general groups: (1) units which measure and (2) units which both measure and control a process variable.

Jan 1, 1979

By R. C. Canby

JUDGE GRANT, in a delightful satire of his, says: "Boston is a state of mind." I think that this same statement might well be made of the metallurgy of lead. I was particularly impressed with this when about thirteen or fourteen years ago I prepared a paper on "Development of the American Water- jacket Lead Blast Furnace." Dividing the time, as I did into ten-year periods, from the commencement of lead smelting at Eureka, Nev. (1870), and showing the tendency for each of the five decades it was evident that the progress had been through a succession of states of mind from the rule of thumb through the ultra scientific, or from what I might call the slag type period up to the present highly developed art. Conservatism has been characteristic of the metallurgist. This may have been most natural, especially with the lead metallurgist, the development of whose art was so entirely in the custom smelting plant, where the metal contents of his ores were paid for in cash and therefore excessive metallurgical losses could mean nothing short of financial bankruptcy. The metallurgist himself was held to a personal account, in these smelting plants. It was the metallurgist who was accountable. In the concentrating plants, if undue losses occurred remodelling of the plant was discussed, but if there were excessive metallurgical losses in the custom smelting plant, a new metallurgist was considered as the remedy. For this reason the tendency was to adhere to recognized practice and to be wary of unusual methods, using the word unusual in the sense in which it is used in Article VIII of the Constitution of the United States, as to punishments and modes of death. This conservatism of the metallurgist was reflected as other branches of metallurgy were developed. We have heard of the wonderful development of flotation, but it had to be introduced over the dead metallurgical bodies of its opponents.

Jan 1, 1926

The Role of the Drilling Contractor BY FERRIS E. SAINSBURY Ron Haxby, Occidental Minerals What is the best method for drilling a 12-in. diam hole to a depth of 1200 ft and maintaining the deflection within 25ft from vertical? Ferris Sainsbury: In order to drill a 12-111. hole down to 1200 ft, In most places you would have to employ a rotary tricone bit With a down-the-hole hammer, I expect by that depth significant Inflows of water would be experienced Even with foams, we would not be able to get the water out of a hole of that diameter So the down-the-hole tricone method of drilling would be best. To keep it straight, we would probably employ the largest square drill stem compatible with the diameter of the hole. Ron Haxby: Is it common in drilling contracts to put in a vertical hole clause? Ferris Sainsbury: You can put in the vertical hole clause Ron Haxby: Does it cost more? Ferris Sainsbury: Normally, if the hole deviates, the driller can correct it with deflection wedges and will charge it back to you at cost, plus 10% or somewhere along that range Any drill hole has a tendency to go perpendicular to the dip, and there are times when stabilization systems are not successful in preventing the hole from turning into the dip of the formation. The only solution, in this situation, is to go in with an oriented wedge and kick the hole back out.

Jan 1, 1979

By M. R. Tek, K. H. Coats, D. L. Katz

A large number of boundary value problems encountcred in unsteady-state heat transfer, fluid flow through porous media, neutron diffusion and mass transfer involve the solution of a linear, parabolic partial differential equation commonly refcrred to as the diffusivity equation, where U is the dependent potential variable. K is the diffusivity (hydraulic, thermal, neutron, etc.) and 1 is the time variablc. Solutions to Eq. I are available in the literature for a wide variety of initial and houndary conditions. The great majority of these solutions are ohtained for geometric boundaries corresponding to linear. cylindrical or spherical flow models. A typical engineering application where the solution to Eq. 1 is required is the calculation of underground water encroachment across the boundaries of oil or natural gas reservoirs, In this particular area of application, the reservoir boundary is invariably approximated by circular geometry. However. the areal shape of many reservoirs can be better approximated by elliptic rather than circular boundaries. Thus the need for a general method of solving the diffusivity equation in elliptic coordinates arises in this problem as well as in other engineering applications involving elliptic boundaries. The solution to the diffusivity equation usually in volves the Error Function for the linear flow model, Bessel functions for the radial flow model and trigonometric or Legendre functions for the spherical flow model. It is well known that the general solution to the diffusivity equation in elliptic coordinates involves Mathieu functions. The significance of Mathieu functions in the analytical treatment of the diffusivity equation in elliptic coordinates is discussed in the literature However, these references do not providc analytical solutions useful in practical engineering problems. The objectives of this papcr are the development of the equations describing the unsteady-state liquid flow through a porous medium with an elliptic inner boun- dary, the development of a numerical method of solving these equations and, finally, a comparison of the water encroachment quantities calculated from the elliptic flow equation with those calculated from the radial flow equation. While the specific problem treated in this paper relates to unsteady-state liquid flow through a porous medium, the basic equations and computational techniques devcloped will apply equally well to problems occurring in the other areas of engincering interest mentioned previously. The solution given here is limited to a single case in which thc outer boundary encloses an area 100 times that of the inner boundary. DESCRIPTION OF THE FLOW MODEL Fig. 1 shows the flow model upon which the calcu lations presented in this paper are based. The inncr and outer houndaries of the flow model are represented by two confocal ellipses with major and minor axes, respectively, equal to 2a1, 2b1, and 2a, and 26,. The height of the elliptic cylinder flow model is denoted by 17. The following assumptions are employed in the development 01 the equations governing the unsteady-state liquid flow through the described flow model. 1. Uniform porosity and permeability throughout the flow model

By Dan G. Cojocariu, E. Ene-Danalache, I. Huber-Panu

A general model which represents not only batch but also continuous flotation in multi-cell machines is presented. This model considers both the size distribution and the distribution of flotabilities in a size class for valuable mineral particles in the pulp. The general expression is shown to reduce to several previously reported models. In addition, a number of new models are found to arise for different specific assumptions concerning the flotability distribution and/or the size distribution of the particles undergoing flotation. Several of these new models are tested experimentally using laboratory-scale batch and pilot-scale continuous data. Model parameters are estimated from this data and a comparison of calculated recoveries and those experimentally determined are presented. Finally, the influence of the feed rate, aeration rate and valuable mineral content of the feed on the recovery is examined.

Jan 1, 1976

By L. Weaver

THE Tennessee Copper Co.'s mines are in the southeast corner of the state of Tennessee. Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails. The shaft is 12 ft 7 1/2 in. ID of the concrete walls. This is large enough for two 10-ton hoisting skips and a ladder compartment. One of the skip compartments is for hauling equipment. The grouting equipment was a 2%xlO-in. Gardner-Denver grout pump, air powered and developing 1000 lb pressure. A grout mixer, also air driven, fed the mixed solution into a tank coupled to the pump suction. Grout materials used were mostly water and Portland cement. Some Bentonite was used to seal porous ground near the surface.

Jan 11, 1950

By H. H. Power

THE PETROLEUM DIVISION of the A.I.M.E. continued with its diversified activities during 1.935. Sessions at the New York meeting in February were devoted to production engineering, domestic and foreign oil production, and petroleum economics. The symposiums on domestic and foreign production proved their increased usefulness. The data accumulated for 1935 were added to those published during prior years in "Petroleum Development and Technology." A joint session on the use of metals in the petroleum industry was held by the Institute of Metals, Iron and Steel, and Petroleum Divisions. W. S. Farish, chairman of the board of the Standard Oil Co. (N. J.), was the principal speaker at the annual dinner. The October meeting, held in Hous¬ton, was characterized by an excellent program and large attendance. Four sessions were devoted to problems in estimating reserves, reservoir energy, properties of drilling muds, electrical logging, water flooding, and other subsurface studies. Foreign representatives of the Anglo-Persian Oil Co. presented a paper on surface tension and specific gravity of crude oil under reservoir conditions. The address by President Buehler, the dinner at San Jacinto Inn, a trip to various lo

Jan 1, 1936

By R. D. Pehke, J. F. Elliott

The solubility of nitrogen in liquid pure iron has been measured as a function of pressure and temperature. Sieverts' Law is obeyed at all pressures up to 1 atm and the temperature coefficient of solubility is 8 x 106 %/°C. The solubility of nitrogen in liquid iron alloys has been studied by the Sieverts' method and by the sampling method. The solubility is decreased by Al, C, Co Cu, Ni, 0. Si atzd Sn, and it is increased by Cr, Cb, Mn, Mo, Ta, W, and V. Interaction coefficients eN, for the effect of these elements on nitrogen dissolved in liquid iron, are reported. 1 HE effect of nitrogen upon the properties of steel may be desirable or not, depending upon the composition, processing treatment, and the use of the product. To understand the behavior of nitrogen in the various steelmaking processes, it is necessary to have reliable fundamental data pertaining to the solubilities, rates of solution, and chemical reactions of nitrogen in steel, particularly in the liquid state. In an effort to extend our knowledge in these areas, an investigation of the thermodynamics and kinetics of the solubility of nitrogen in liquid iron alloys was undertaken. The thermodynamic aspects of the study are presented in this paper. The solubility of nitrogen in liquid pure iron has received the attention of several investigators whose results are summarized in Table I. Reasonable agreement among the more recent researches1-l8 is found for the solubility of approximately 0.044 wt pct at 1600°C and 1-atm pressure of N,, for the temperature coefficient of solubility being small but positive, and for adherence to Sieverts' law for pressures up to 1 atm. The solubility of nitrogen in a number of binary liquid iron alloys has been studied: Fe-A1,3 Fe-As,16 Fe-C,3, 71 18, 19, 20 Fe-Cr ,5,7, 10, 11, 15 21 Fe-Co,'4, '6 Fe-Cu,'6 Fe-Mn,10, 11, 18 Fe-Mo,13, 16 Fe-Ni,10, 11, 13, 15, 16 Fe-O,16, 17, l9 Fe-p,7 Fe-S,l6 Fe-Sb,16 Fe-Se,lg Fe-Si,4) 97 '77 187 19>2° Fe-Sn,16 and Fe-v.51 '3 A few ternary systems have been studied, most of which were reviewed by ~angenberg" who applied the methods suggested by WagnerPz3 Chipman,24 Darken and G~rry, and Morris and Buehl26 for predicting solubilities in multicomponent alloys. Langenberg22 and Humbert and Elliott15 compared the solubilities computed from simple binary alloy systems with experimental measurements of nitrogen solubilities in liquid iron containing two or more alloying elements. The interaction coefficients for nitrogen in

Jan 1, 1961