Search Documents

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By Pat McLaughlin

Blast design in the construction industry has often been based on past practice or powder factors. This is to some extent understandable, since construction projects do not have the longevity of mining or quarrying operations and therefore have less opportunity to pursue potential improvements. The main concern of the operator is whether or not the technique will work, and at what cost to the downstream processes. Time, not long term savings, is of the essence.

Jan 1, 1994

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Harold E. Marr

A simple algorithm is presented for processing digitized X-ray spectra obtained with a Si(Li) or Ge(Li) semiconductor detector coupled to a multi- channel analyzer. The simplified least-squares procedure is used to smooth out the statistical fluctuations in the spectrum by repeatedly fitting a quad- ratic equation to a predetermined number of channels and performing a traveling smooth across the spectrum. A logarithmic transform is applied to the raw data to minimize the distortion of the gaussian-shaped peak profiles. The efficacy of the technique is evaluated by observing the distortion of several gaussian-shaped peaks that have been subjected to the smoothing operation. The locations of maximums and minimums in the spectrum are predicted in the process as well as the values of the peak heights. The convolution integers from a least-squares fit of a quadratic equation are calculated as part of a FORTRAN subroutine. The building-block approach to computer programing in a small laboratory is discussed.

Jan 1, 1972

By J. Eric Nylund

"Intensive mechanization and automation in the LKAB, Kiruna Mine in Sweden have resulted in substantial rise in productivity and decrease in production cost. Capital investment in a modern mine today averages a considerable amount per miner and costs increase with requirements for more efficient methods and equipment. Equipment reliability becomes more and more important. Equipment maintenance requirements are directly proportional to equipment reliability and grade of availability. Weaknesses in the equipment result in unnecessary costs with regard to maintenance which can add up considerably per year, but of more importance are the costs caused by equipment breakdown. These breakdowns disturb or interrupt the production and often cause damage to other parts of the system. This paper discusses the important parameters involved in mine car wheel wear and the design principles of wheels, axle suspension and track.IntroductionTrains operating in an underground mine do not follow the same standard of performance as trains operating on surface railways. The differences in speed, curve radius and environment require different methods of calculation for underground train systems, and when judging the parameters involved one must keep in mind these differences at all times.While surface railway technology was given all possible attention over the last century no one was seriously looking into underground rail haulage in the sense of rail vehicles performance on the track until LKAB in 1975 started to question the methods of calculations used. Even though LKAB by then attained mine car maintenance cost that was 1/6 to 1/10 of other mining companies they were not pleased with the situation. The objective for the ensuing engineering work was to derive the reasons for wear and breakdowns. Once those reasons were established, the design of a completely new generation of mine cars could start. The result of these efforts were beyond all expectations. The maintenance cost on mine cars had been reduced to 1/15 of prior car generation which already had comparatively low cost.The most significant cost savings were made on wheel maintenance, which earlier represented 50% to 55% of car maintenance. Wheel life was increased from an average of 3 to 30 years or more.The LKAB theories around wheel wear are described in the following report."

Jan 1, 1987

The objective of this handbook is to provide the inspector with guidance for recognizing hazards from inhalation contaminants in above ground work areas of underground and surface coal mining and processing facilities and evaluating these hazards by collecting samples or making field determinations and interpreting the analytical results. There are several portions of the handbook which should prove most useful to the inspectors. The names and locations of these portions are listed below: Survey Check List (Page 2-3) Rules for Determining if Sampling is Required (Page 2-1) List of Most Frequently Encountered Contaminants (Page 2-2) List of Candidate Contaminants and their Sampling Conditions (Table 2, Starting on page 2-5) Interpretation of Results (Page 2-16) Procedure for a, Health and Safety Inspection (Page 2-25) For obtaining information not available from the above mentioned portions of the handbook, the inspector is directed to the Table of Contents, the Glossary of Terms, and the List of Commercial Products Encountered in Surveys.

Jan 1, 1975

By Dipak C. Talapatra

This report describes the development of guidelines for design, inspection and maintenance of automatic couplers. In order to devise the guidelines, performance requirements for automatic couplers were carefully established. This was clone through a comprehensive survey of coupler manufacturers and extensive observation of automatic couplers in service in a broad spectrum of mines. The capability of the couplers to withstand the demands of the mining environment in terms of strength characteristics, gathering range, curve negotiability, and other factors were all carefully evaluated. An analysis of coupler related accidents for the years 1972-1976 was carried out to provide information on the safety and reliability of existing automatic couplers. This formed an important input to the development of the guidelines. It is expected that these guidelines will he useful to coupler manufacturers for establishing designs for improved automatic couplers, and to mine operators for maintaining their couplers in a safe and good operating condition throughout their expected lifetimes. This report is in two volumes: Volume l - Technical Report Volume 2 - Design, Inspection, and Maintenance Manual

Jan 1, 1977

By Walter E. Pittman

In its role of providing technical assistance to the mining industry, the Bureau of Mines' Tuscaloosa Research Center has conducted research to develop trapped miner location systems which would aid in locating miners trapped by underground mining disasters. Efforts to produce electromagnetic systems for the location of trapped miners underground and to communicate with them were surveyed, from the 1920's to 1981. Theoretical studies of through-the-earth electromagnetic transmissions are described as well as studies of the electrical characteristics of various rocks, minerals, and soil. Several trapped miner location systems are reviewed including the Westinghouse systems, the DEVELCO system, and an automated three-dimensional location system, and the phase difference of arrival technique. Tangential research, relevant to trapped miner location systems is described. A comprehensive bibliography covering all aspects of trapped miner, through-the-earth electromagnetic location and communications systems is appended.

Jan 1, 1982

The deposit was discovered during systematic reconstruction of the geological history of glacial overburden, which averages 6 m in thickness over 80% of Sweden, by geochemical sampling and searching for small grains of eroded bedrock. The gold is mainly concentrated in and around high-grade quartz veins within a broad shear zone, though the correlation coefficient between quartz and gold in samples is not significant. Production from two pits, now connected, in the Central and Eastern orebodies has increased steadily from 1 238 kg Au in 1989 to 2 120 kg in 1994, the highest in Europe. The mine has adapted and improved its mining methods to achieve significant productivity increases and cost reductions. Most of the improvements have been achieved through a better understanding of the controls on mineralisation and of the implications of those controls for selective mining. Geostatistics has played an important role in the quantification of grade variability and gold occurrence. Better blasting and loading techniques have improved selectivity, grade control has been enhanced by a grade-control drilling programme, and significant improvements in mineral processing have been made

Dec 1, 1995

By I. L. Bell

The ironmasters of America had asked the Iron and Steel Institute to visit the USA. The Council decided it was not possible to accept, but Mr. Bell visited; this is an account of his trip. Topics covered include transport, charcoal, coal measures, coal, anthracite, bituminous coal, flux, magnetic iron ore, specular iron ore, limonite, red hematite, clay ironstone, black band ironstone, smelting works, blast furnaces of Pennsylvania, Lake Champlain furnaces, Lake Superior furnaces, Cleveland furnaces, Pittsburg furnaces, Missouri furnaces, and those of the southern states. He goes on to describe Catalan hearths, malleable iron works, Bessemer works, the Blair steel process, and labour.

Jan 12, 1875

By Lawrence Williamson, Randall J. Essex, David P. Field

As part of a $2.2 Billion bridge project that will link Indiana and Kentucky, an interchange project northeast of Louisville will require the mining of a 6-lane tunnel system about 2,000 ft long in order to cross beneath the historic Drumanard Estate. This paper will discuss preliminary engineering that has been undertaken to compare two-bore and three-bore layouts, the planning of an exploratory tunnel facility, and the potential for including a test chamber to investigate the ability of high capacity roadheaders to mine the 22,000 psi limestones.

Jan 1, 2005

At Waiuta near Reefton there is a remarkable vein of quartz <1 m thick which, apart from small offsets on late-stage faults, is a sheet like body essentially continuous down-dip and along-strike for> 1 km. The vein strikes NNE and dips steeply west (032/78¦W). From 1906-1951 the Blackwater mine produced 740,404 ounces of gold from the vein, called the æBirthday ReefÆ, which was one third of the total production from Reefton Goldfield and the fourth largest gold mine in New Zealand. Within the mine the vein is disrupted into a series of northeast-plunging shoots by late-stage faults. Similar faults, but with larger displacements, were thought in the past to truncate the vein at the northern and southern ends of the mine. The implication of this fault dissection model is that offset remnants of the vein await discovery. This study investigated the geometry of the vein and its relationship to host-rock structures and late-stage faults. A new model considers folding and lithological variation in the host-rocks to be fundamental in controlling the scale and geometry of veining, but does not rule out the possibility of some late-stage fault dissection. The Birthday Reef truncates 200-400 m wavelength folds in Greenland Group host-rocks at c.10¦ angle, that results in variation in the structural properties of host-rocks along strike every ~1350-2500 m. The spacing of fold hinges in the wall-rock veins is equivalent to the strike length of historic mining, implying that the Birthday Reef is probably hosted in a single limb of a fold. Similar relationships between mineralisation and host-rock folds appear to be present elsewhere in the Reefton Goldfield (e.g. Capleston and Murray Creek group of mines). Exploration targets are located one fold wavelength (c.1350-2500 m) further along strike from the Blackwater mine and relatively barren rock is expected in between the mine and target areas. Refining the location of folds and different host rock lithologies, using geophysical data and quality geological mapping, is the key to reducing exploration risks and discovering further resources.

Jan 1, 2000

By Tom Barry, Kameron Ray, Dr. Gavin Yuill

Imerys Talc, Yellowstone Mine in Montana faces significant geotechnical challenges such as poor wall quality and local instabilities. These instabilities are driven primarily by the characteristics of the rock mass, but are aggravated by drilling and blasting operations.

Jan 1, 2016

By H. Sis, D. Dahlin, S. Chander, C. Summers

Bench-scale selective-flocculation tests were conducted on samples of Florida and Western phosphate process tailings. Physical, mineralogical, and surface characteristics were determined for both types of samples. The flocculation tests investigated dispersant and flocculant types and doses, pH, and slurry percent solids, while other parameters were held constant. Where selectivity was achieved, phosphate minerals remained dispersed, whereas silicate minerals flocculated and settled. In single-stage tests, flocculants having low to medium anionic character effectively upgraded products at moderately elevated pH. Multiple-stage tests, and tests in which flocculants of lower molecular weight were used as site-blockers, gave improved results.

Jan 1, 2002

By Harry G. Poulos

Ground movements can arise from a large number of sources and can have a significant effect on nearby piles and deep foundations. The loading of the piles by ground movements is a different mechanism to that arising from direct applied loading to the pile head, and consequently it is not generally possible to adequately analyze the effects of ground movements simply by applying some type of equivalent loading to the pile head. The main effects of ground movements are the development of additional movements, axial forces and bending moments in the piles, and thus the key design aspects are related to movements and to the structural integrity of the pile. However, the ultimate geotechnical load carrying capacity is generally not affected by the ground movements themselves. This paper will describe an approach to the analysis of ground movement effects on piles, considering axial and lateral movements separately. Some of the main features of pile response will be discussed for three specific problems involving ground movements: 1. Piles near and within embankments; 2. Piles near an excavation for a pile cap; 3. Piles subjected to seismic ground motions.

Jan 1, 2007

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

Errors in ore reserve estimation can occur during drilling and sampling, sample preparation and analysis, geological logging and modelling, database construction, statistical or geostatistical evaluation, selection of economic parameters, selection of ore reserve method and assessment of mining constraints. Core sample recovery can be a major source of error, and it is proposed that the modelling of grade, metal accumulation and thickness should be accompanied by the modelling of core recovery (or core loss) so that for each ore block a weighted block recovery factor is obtained. This gives a good indicator of the reliability of a reserve estimate. It is suggested that a resource reliability rating (RRR) system be established to quantify what is meant by geological assurance and to combine this with an estimate of the precision of estimation as gained by geostatistical analysis. Proven and probable minable reserves would be those with an RRR better than 50% and a precision of estimation better than 20%

Dec 1, 1996

By Stephen D. Smith

The following tables summarize data on crude nonfuel mineral production for the United States, its island possessions, and the Commonwealth of Puerto Rico. Although crude mineral production may be measured at any of several stages of extraction and processing, the stage of measurement used in these tables is what is termed "mine output." It usually refers to minerals or ores in the form in which they are first extracted from the ground, but customarily includes the output from auxiliary processing at or near the mines. Because of inadequacies in the statistics available, some series deviate from the foregoing definition. For copper, gold, lead, silver, tin, and zinc, the quantities are recorded on a mine basis (as the recoverable content of ore sold or treated). However, the values assigned to these quantities are based on the average selling price of refined metal, not the mine value. Mercury is measured as recovered metal and valued at the average New York price for the metal. The values shown are in current dollars, with no adjustments made to compensate for changes in the purchasing power of the dollar.

Jan 1, 1995

By Michel R. Julien, Michel Lemieux, Jean Cayouette, Daniel Talbot

"The Louvicourt Mine located near Val d’Or, Quebec has been in operation since 1994. It produces copper and zinc concentrates. The tailings generated from the ore processing operations have a strong net acid generating potential. Louvicourt Mine, a grass root project, was designed for closure with the best available technology at the time of design. In order to inhibit short and long time acid potential generation, sub-aqueous disposal was selected at the design stage. Given the fact that disposal in a natural lake was ruled out up front for obvious reasons related to loss of natural habitat and risks of permitting delays, a man made facility built with dams was planned. This mine includes therefore the first fully man-made sub-aqueous tailings disposal facility built in Canada. The requirement of using sub-aqueous disposal had serious implications on the placement of tailings. This tailings facility located about 9 km from the mine site has been selected based on the available natural confinement, the favorable foundation and hydrogeological conditions. This paper describes the site and the design criteria that were used. A presentation is also made on the placement technique to maximize storage and its impact on the operation of the basin. The performance of the basin, the dams and the decant structures is reviewed.Résumé : La mine Louvicourt, située près de Val d’Or, Québec est opérationnelle depuis 1994. Elle produit des concentrés de cuivre et de zinc. Les résidus générés par les opérations de traitement du minerai possèdent un fort potentiel net de génération d’acide. Le parc à résidus de la mine Louvicourt, implanté dans un milieu naturel intact, fut doté dès sa conception initiale de la meilleure technologie de fermeture disponible à l’époque, soit la déposition sous couverture aqueuse et ce, dans le but de bloquer le potentiel de génération d’acide à court et à long terme des résidus. Etant donné que la déposition dans un lac naturel fut mise de côté dès le départ pour des raisons évidentes reliées à la perte d’habitats naturels et au risque d’introduire des délais dans l’émission des permis, un étang artificiel délimité par des digues a été conçu. Cette mine fut donc la première au Canada à être dotée d’une installation anthropique de disposition des résidus sous une pleine couverture aqueuse. L’exigence d’une déposition sous couverture aqueuse a eu des implications sur le mode de mise en place des résidus. L’emplacement de l’installation de gestion des résidus a été choisi en un lieu situé à environ 9 km du concentrateur sur la base du confinement naturel disponible et des conditions hydrogéologiques et géotechniques favorables. Cet article décrit le site et les critères de conception utilisés. Une présentation est faite sur la technique de mise en place utilisée pour maximiser l’entreposage et son impact sur l’opération du bassin. La performance du bassin, des digues et des structures de décantation est également revue."

Jan 1, 2004

By I. L. Follington

This paper describes the research and development programme to develop a prototype underground auger mining system aimed at developing and demonstrating an underground auger mining system able to provide economic access to thinner (<1.8 m) coal reserves of South Africa. Data concerning the performance of modern coal augers under South African coal mining conditions were gained from a proven surface auger which operated across a range of coal types. These data were analysed and considered in conjunction with historical information regarding previous attempts at building underground augers dating back to the 1950s. Drawing on these data a prototype underground auger mining system, the BryDet BUA 600 underground coal recovery auger, was designed and manufactured by the BryDet Development Corporation in collaboration with Eskom and Cutting Edge Technology Pty Ltd with support from Anglo Coal and the Ingwe Coal Corporation Ltd. The prototype BryDet BUA 600 underground coal recovery auger commenced trials in March 2000 at the Matla Mine near Witbank in South Africa. The initial trials were undertaken in an open cut to facilitate the commissioning and training associated with a prototype mining machine. A total of 30 holes was augered in the box cut before the machine moved underground. The prototype BUA 600 first achieved the target penetration depth of 80 m in its third hole. The prototype BUA 600 is a new underground mining system which has passed early testing with ?flying colours? and could provide access to extensive underground coal reserves unmineable by conventional mining techniques both in South Africa and elsewhere around the world.

Jan 1, 2001