Search Documents

By B. Spigarelli

Carbon dioxide sequestration by conversion to carbonates has become a promising option for CO2 storage. Experiments were conducted to determine the feasibility of CO2 sequestration at ambient conditions using a Ca-rich industrial waste in a carbonate solution. The Ca-rich industrial waste used in this study was lignite fly ash. Fly ash was chosen because it is cheap, available near large CO2 point sources, already in powder form, and reactive due to amorphous properties. In the experimental set-up, CO2 absorption was inferred by monitoring feed and exhaust gas CO2 concentrations. The addition of an alkali to a fly ash-distilled water solution provided a 50% increase in CO2 absorption of the solution. Absorption time also increased by 50% compared to a fly ash-distilled water solution. TGA analysis was used to determine the extent of CO2 sequestration in the carbonate form. At a liquid to solid ratio of 20:1, the conversion of ?free? calcium to carbonates was 75%. A CO2 balance on the system concluded that at the current operating conditions 42% of the total CO2 fed to the system was sequestered in the carbonate form. SEM-EDS analysis of the fly ash particles before and after reaction with CO2 indicated that the carbonate compound being formed was calcium carbonate. The analysis identified rhomboidal structures on the surface of the fly ash particles after reaction with CO2, but not before. These rhomboids are characteristic of calcium carbonate formation and they had higher Ca, C, and O concentrations than the host spheres, suggesting calcium carbonate formation.

Jan 1, 2012

By K. Hanna

This U.S. Bureau of Mines report describes a rock mechanics instrumentation program conducted in a shallow underground coal mine in central Illinois. This research program was designed to provide a basic understanding of the structural behavior of entry intersections. A wide variety of instruments and measurement techniques including hydraulic borehole pressure cells, multiple-point borehole extensometers, roof bolt compression pads, and overcoring were employed to monitor roof stresses, pillar loading, strata movement, floor heave, and bolt loading before, during, and after intersection development. A summary of intersection design theories, failure modes, and support techniques is included and instrumentation installation procedures and analysis methods are presented. The study identified two critical parameters that affect intersection stability: in situ horizontal stresses and geological discontinuities. Important design parameters for improving intersection stability are roof span and intersection geometry.

Jan 1, 1991

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By Y X. Xue, J Pan, D Q. Zhu

In order to reveal the correlation between the fundamental sintering characteristics of iron ores and their real sintering behaviours, a comprehensive evaluation index is proposed based on the measurement of four high temperature indexes, ie assimilation temperature, liquid phase bonding strength, liquid fluidity and calcium ferrite formation percentage, and the sintering pot tests of single ore fines and their blends. The results show that both the lowest assimilation temperature and liquid fluidity of ore blends appear to be the linear superposition of those of single iron ores except for the liquid phase bonding strength and calcium ferrite formation percentage. Furthermore, the tumble index of the sinter product obtained from blended iron ores also corresponds to a linear superposition of that of single ores, but not for the solid fuel rate and productivity. The comprehensive strength index YT exhibits a credible linear positive correlation with the four high temperature reactivity indexes, whereas the comprehensive productivity index YP possesses a lower correlation with the four high temperature reactivity indexes. The comprehensive strength index YT developed can predict the tumble index of the sinter product quite well, but the comprehensive productivity index YP cannot be used to evaluate the productivity effectively.CITATION:Zhu, D Q, Xue, Y X, Pan, J and Shi, B J, 2017. Correlation between high temperature sintering characteristics and sintering behaviours of iron ore fines, in Proceedings Iron Ore 2017, pp 123–132 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

By D Craw, D Wilson, D Chappell

Gold is extracted by cyanidation of a sulphide-rich concentrate at Macraes mine, and after cyanidation, the concentrate is discharged to tailings impoundments. The concentrate tailings were discharged to a dedicated concentrate impoundment from 1989 to 1993, afterwhich they were blended with the flotation tailings. Since mid-1998, concentrate tailings have been redirected to the dedicated concentrate impoundment. The concentrate tailings contain up to 1 ppm gold, and will be reprocessed in the future. However, it is a regulatory requirement that a contingency plan be in place to rehabilitate the concentrate tailings should the mine operation cease for any reason. Initial predictions suggested that the sulphide-rich tailings would oxidise and acidify, creating a potential long term environmental problem. Investigations of the state of the tailings after 4 years show that these predictions were overly conservative. Only minor oxidation has occurred in the upper 2 metres of the tailings where the pH has locally dropped from 10 (discharge condition) to between 7 and 8. Below 2 metres, the tailings are essentially unchanged from their deposition state. The low rate of change in the tailings is due to their very low permeability which in turn is a consequence of the fine grain size (ca. 15 ¦m). Dewatering is extremely slow, and incursion of oxygenated water is negligible. Calculations suggest that water movement over 30 m will take at least 100 years and possibly 1000 years. The contingency plan is to capitalise on the very low permeability and keep the tailings from drying with a semipermeable cap. A layer of limestone will be added to the top of the tailings, beneath the cap, to enhance alkalinity of any percolating water. If acidification does occur, contrary to expectations, any acid produced will be neutralised by underlying calcite-bearing schist, schist in the concentrate impoundment wall, and the flotation tailings immediately downstream. In addition, dilution by alkaline ground and surface waters would further ameliorate any acidic discharge.

Jan 1, 1998

By A. R. Taylor

In recent years, thermodynamic data have been used to a greater degree than ever by the chemical and metallurgical engineer as a means of predicting and controlling chemical reactions. To satisfy the spiraling demand for basic physical data needed for the calculations, the Bureau of Mines is studying the heat capacities of a variety of chemical compounds at high and low temperatures. This paper is one of a series presenting such data. The heat capacities of two alkaline earth compounds, strontium bromide and strontium nitrate, were measured in a temperature range of 60° to 300° K. in an adiabatic calorimeter and at temperatures of 300° to about 1,200° K. in a Bunsen ice calorimeter. The construction and operation of the calorimeters are discussed in other reports.3 4 The heat-capacity data presented in this report were extrapolated to 0° K., and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were calculated and tabulated at even 10-degree intervals. The enthalpy data were fitted with algebraic equations by applying the method of least squares; calculations a£ heat-capacity values, entropy, enthalpy function, and free-energy function were made at even 50-degree intervals. The heat and entropy of fusion of strontium bromide were calculated from the enthalpy measurements.

Jan 1, 1962

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By G J. Lyman

In sampling a process stream, conventional sampling theory deals only with the variation of the analyte content and neglects the impact of the variation in the mass flow on the sampling variance, whether the sampling regime is time-based or mass-based. This is an obvious simplification of the real state of affairs and it is worthwhile to study this impact via simulation.With a facility to simulate large (long) random functions having some thousands of points in the function and the ability to impose covariance functions on the mass flow and analyte variations, such a study is possible. It is also possible to evaluate the impact of correlation between analyte content and mass flows.This paper describes a limited study of the variance increase due to mass flow fluctuations over the usual sampling variance due to analyte variation during the sampling period. The bias in the sampling result is determined for specific modes of correlation. Simulation methods are used as they are the only means by which a sampling result can be compared to the true assay for the lot; in the physical circumstances of mineral process analysis, it is never possible to determine the true process stream assay.CITATION:Lyman, G J, 2017. The impact of the weighting error, in Proceedings Eighth World Conference on Sampling and Blending , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Drupad B. Desai, Bruce Chang, Jay L. Merritt

This paper reviews difficult ground conditions encountered along the alignment of large-diameter sewage tunnels for the City of Los Angeles. It offers a detailed one-of-a-kind solution to a unique problem for shallow urban underground tunnels in a seismic zone, using state-of-the-art materials, technology, and equipment. The following topics are discussed in detail: • Geotechnical Design consideration for tunnel traversing through an active fault zone. • Seismologist evaluation of possible fault-offset problems where a fault zone crosses the alignment, in the event of an earthquake of moment-magnitude 6.5. • Probability analysis regarding "recurrence interval." • Structural design of tunnel subjected to displacement, subjected to axial elongation or shortening, and capable of rotational freedom. • Special joint details.

Jan 1, 1989

By D. Z. Mraz, R. S. Jones

Unlike in coal mines where caving methods are used, the subsidence over potash mines in Saskatchewan, Canada, is a function of gradual mining convergence. Because of the presence of high pressure water aquifers over the evaporite salt formations, the mines have to be designed as regionally stable and no caving is allowed. The extracted area converges gradually and the convergence is mainly a function of the extraction and the mining method employed. Consequently, the subsidence rate is very slow and the bridging of the over-lying strata is a considerably more important phenomenon than elsewhere. The paper evaluates a case history of convergence and subsidence in a deep potash mine in Saskatchewan.

Jan 1, 1986

By Kyle Ott, Bernard Daly, Syed Haq, Douglas Anderson, Parsons Brinckerhoff

Drill and blast was determined to be the most cost-effective means of excavating the Raw Water Tunnel (RWT) for the Croton Water Treatment Plant in the Bronx, New York City. One of the major issues confronting project designers was the potential impact of blast vibrations on a major City Distribution Tunnel (CDT). The proposed path of the RWT would cross less than 30 meters (100 feet) above the CDT, which was built in 1917. Discussions with New York City Department of Environmental Protection led to vibration criteria on the CDT of 51 mm/sec (2 in/sec) peak particle velocity as an alert level, and 38 mm/sec (1.5 in/sec) as a review level.

Jan 1, 2012

By S. P. Singh

Drifts are an integral component of underground mining. They provide access for men and material, means for transporting ore and rock and serve as air passageways. In view of their importance on the overall safety, economy and productivity of mines, empirical guidelines for controlled blasting design in drifts have been developed in this study. The application of the proposed concept was described by generating blast hole patterns for a mine with the help of a computer program. The mechanism of blast damage and the need for controlled blasting to alleviate ground control problems in underground mines have been outlined in this paper. The economic analysis between normal-and controlled blasting was performed based on the information from an operating mine. In addition, the review of drift blasting practices and problems in Canadian mines was also carried out in this study.

Jan 1, 1990

By B. Anameric, S. Kawatra

Pig iron nuggets, which have similar chemical and physical properties with blast furnace pig iron, were produced by a single step heat treatment of self reducing – fluxing dried greenballs. During this single step heat treatment the transformation of self reducing fluxing dried greenballs into pig iron nuggets did not take place instantaneously. Rather, it was composed of three transformation stages, (1) transformation of self reducing – fluxing dried greenballs into direct reduced iron (DRI), (2) transformation of DRI into transition direct reduced iron (TDRI), and (3) transformation of TDRI into pig iron nuggets. Thus, the objective of this research was to investigate these transformation mechanisms by analyzing the transformation stage products. The transformation stage products were produced at a constant furnace temperature of 1425°C and various furnace residence times. They were characterized according to their microstructure, microhardness and apparent density. The changes in the product’s physical and chemical properties with furnace residence time were utilized in understanding the transformation behavior, the chemical events that took place and the controlling mechanisms. It was determined that the transformations were dictated by the changes in the slag viscosity and wetting properties, and by carbon diffusion into metallized areas.

Jan 1, 2007

By Carole L. B. Mitchell

The South 180th Street Grade Separation underpass in Tukwila and Renton, Washington, USA, permits vehicular traffic to pass beneath Burlington Northern Santa Fe and Union Pacific railroad tracks. The railroad tracks were temporarily relocated onto a shoofly crossing while the permanent bridges were constructed. The maximum underpass depth is approximately 25 feet (7.6 meters [m]). The majority of the sidewalls are supported using alternating reinforced and unreinforced secant pile walls. Temporary and permanent struts brace the top of the excavation. Because the groundwater is about 15 feet (4.6 m) above the base of the excavation and the subsurface materials are loose to medium dense fill, alluvium, and soft flood plain organics, the base of the excavation was strengthened and sealed using wet cement deep soil mixing (CDSM) methods. During construction, CDSM-treated ground temporarily acted as part of the railroad shoofly shoring while the remainder of the underpass was excavated on either side of active railroad tracks. The combination of secant pile sidewalls and CDSM bottom seal allowed for easy excavation, even during wet conditions. Using a 35-foot-thick (maximum) (10.7-m) CDSM layer both to act as a bottom seal and to resist uplift pressures is a unique, dual-purpose application of CDSM technology in the United States.

Jan 1, 2004

By P. Roy

Smelting or converting of sulphide concentrates and mattes in a batch operation presents a challenge when directing the off- gas to a conventional acid plant. The Hindustan Zinc Ltd. (a division of the Vedanta Group of companies) Chanderia Lead Zinc smelter was presented with such a challenge that was met with the adoption of the Cansolv® SO2 Scrubbing System. The Ausmelt top submerged lance technology used at Hindustan Zinc generates a furnace gas stream that containsbetween 0.1 vol% and 12 vol% SO2 during the three stages of batch smelting. Cansolv® SO2 Scrubbing Technology captures the SO2 to ensure that treated flue gas exits the facility at a concentration below 100 ppmv SO2 and it releases SO2 in a controlled fashion, to more closely match the needs of the existing acid plant. The application of a regenerable scrubbing system to capture SO2 from a batch-operated furnace and convert it to acid in a conventional acid plant was a first of its kind in the world. This paper provides an update on the design and operation of the Hindustan Zinc SO2 recovery system and suggests two improvements to the basic flow sheet that optimize the cost of SO2 scrubbing further.

Jan 1, 2007

By James Noll, Sam Janisko

Underground miners are exposed to some of the highest levels of diesel particulate matter (DPM) in the United States. Therefore, it is important to monitor the exposure of miners to DPM, but it can be difficult because of the complex composition of DPM and the number of interferences. Currently, elemental carbon (EC) is used as a surrogate because it makes up a significant fraction of the DPM and is not affected by interferences. Standard measurement methods for EC can be time consuming and only record end of shift results. In this research, a laser absorption technique that enables one to measure EC concentration in near real time was shown to be a beneficial tool. The real time data showed that the fresh air being drawn into a stone mine was not properly reaching the working area and needed to be redirected to decrease DPM concentrations. The real time data also provided a more accurate efficiency ofan environmental cab compared to just using the standard method by detecting the opening of the cab's window and door. The EC optical monitor was also worn by researchers in a mine to show how it can give not only the average concentration for the shift but also reveal when and where a miner is exposed to DPM. Keywords: Laser absorption, diesel, elemental carbon, mining, exposure

By Xiaowen Liu

The DSC/TG, IR and XRD analysis were used to characterize the heating phase transformation of illite, which came from Ouhai deposit, China. It was discovered that the dehydration and de-hydroxylation of illite carried out stage by stage during heating. The adsorptive water and layer-inter water were dehydrated from room temperature to 500°C; and dehydroxylated in the range 500°C~800°C. In these stages of process, illite?s layer structure kept almost unchanged. After 800°Cillite began to change into disorder structure. At about 1100°C, the layer structure of illite had been destroyed, and amorphous SiO2 and mullite crystallite appeared. At about 1200°C the structure of illite completely destroyed and mullite crystal phase had become perfect..

Jan 1, 2006

By Willard L. Hunter

The research described in this Bureau of Minus report was conducted to improve the chromium-iron ratio of offgrade chromite. Two methods were used: (1) Iron was selectively reduced from chromite by carbothermic reduction in an electric-arc furnace, and (2) a mixture of carbon, chromite, and sometimes fluorspar was chlorinated to remove a substantial part of the iron. Chromite concentrate from the Mouat deposit in Montana and from northern California was used in the test work. Chromium-bearing slag and chromite that had been beneficiated by a roast-leach process were each smelted to produce high-carbon ferrochromium. Iron was selectively reduced in a laboratory-scale., electric-arc furnace. Carbon additions to the smelting charges varied from 40 to 100 percent of the stoichiometric requirement, and slag basicities were varied from 0.4 to 1.0 chromium-iron ratios of more than 4:1 were obtained with 89 percent recovery of chromium in a chromium-bearing slag.

Jan 1, 1962