Search Documents

By Valentín Choquenaira Bombilla

El presente trabajo describe el proceso de automatización de la planta concentradora BHPBilliton deTintaya desde el punto de vista del usuario final y así proporcionar una visión global sobre los aspectos relacionados con la automatización de nuestro proceso a través de sistemas de control distribuido (Distributed Control Systems, DCS) e inteligencia artificial (Sistema Experto).También se describe la arquitectura del control, las formas de conexión (Hardware) y la función que desempeña dentro del sistema cada uno de los componentes del sistema de control distribuido instalados en la planta concentradora de sulfuros de BHPBilliton Tintaya S.A. así como algunos conocimientos básicos de manejo del sistema composer y conductor NT (Software) para realizar las funciones de configuración, monitoreo y control del proceso desde unidades remotas y estaciones de trabajo.

Sep 12, 2005

By M Sherman

The challenge facing the engineering provider is to calculate throughput rates when faced with disparate specific energies calculated by different testing methodologies. Typically, an ownerÆs team would expect that the throughput calculations be checked using more than one method, therefore it is inevitable that there will be differences, based on which methodology is used. This engineering challenge is exacerbated by the continuing evolution of contemporary circuit configurations such as two stage pebble crushing with or without high pressure grinding rolls (HPGRs) as the second stage, or second stage pebble crusher product reporting to the ball milling circuit, etc.This paper is a companion to the paper first presented at SAG 2011, which showed that the Bond Indices are an excellent tool for estimating the specific energy requirements for semi-autogenous grinding (SAG) mills in single-stage SAG milling (SSS) circuits, SAG and ball mill circuits (SAB) or SAG and ball mill circuits with pebble crushers (SABC). This paper presents how the Bond Indices have been used to calculate ball mill specific energies, and therefore throughput rates, for SAG mill based circuits. Once the ball milling specific energy is known, tower mill and vertimill energy requirements can also be calculated. It is noteworthy that the method presented in this paper does not require the use of any unpublished correction factors: the proposed method uses the Bond parameters and equations published by Rowland in 1982.CITATION:Sherman, M, 2013. 21st century bond, in Proceedings Iron Ore 2013 , pp 309-312 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By L. F. Ruppert, W. D. Watson, S. J. Tewalt, L. J. Bragg

The U.S. Geological Survey recently completed a digital coal resource assessment model of the Upper Pennsylvanian Pittsburgh coal bed which indicates that of the original 34 billion short tons [31 billion tonnes] of coal, 16 billion short tons [14 billion tonnes] remain after subtracting mined-out coal. When technical, environmental, and social restrictions are applied to the remaining Pittsburgh coal model, only12 billion short tons [11 billion tonnes] are available for mining. Our assessment models estimate that up to 0.61 billion short tons [0.55 billion tonnes], 2.7billion short tons [2.4 billion tonnes], and 8.5 billion short tons [7.7 billion tonnes] could be available for surface mining, continuous mining, and longwall mining, respectively. This analysis is an example of a second-generation regional coal availability study designed to model recoverability characteristics for all the major coal beds in the U.S.

Jan 1, 2000

By A. Sissing

Paper written on project work carried out in partial fulfilment of M.Sc. (Chemical Engineering) degree Thermophilic bioleaching, conducted at temperatures in excess of 65°C, provides considerable benefit over mesophilic bioleaching, particularly through extending the extent of leaching of base metal minerals such as chalcopyrite. Thermophilic bioleaching is facilitated through a group of micro-organisms known as the Archae, well adapted to extreme environment. In order to maximize the space time utilization of the stirred tank reactor in the thermophilic bioleaching process, it is desirable to maximize the loading of the finely divided mineral phase present while not adversely affecting the microbial performance. In this paper, the effect of the loading of the solid particulate phase on the bioleaching performance of Sulfolobus metallicus was studied in a stirred tank reactor. Emphasis was placed on the effect of the concentration of the finely divided solid phase (35 ? 75 µm). A model system comprised of 3% (w/v) pyrite in the presence of varying quantities of quartzite in the range 0 to 24% (w/v) was used to obtain the different solids concentrations. The bioleaching experiments revealed similar bioleaching performance in the presence of 3 to 18% (w/v) total solids. Above 18% (w/v) total solids (15% quartzite loading), bioleaching was impaired progressively with increasing solids concentration. At the highest solids loading studied of 27% (w/v), bioleaching was still observed. In terms of mass transfer, oxygen transfer potential was not significantly influenced in the bioleaching process over the range of solids investigated.

Jan 1, 2003

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By David Clarry

?The issue ?reduction requirement ?Planning abatement steps ?Energy Management & Energy Efficiency ?Energy Recovery / Utilization ?Alternative Energy Professional Services Overview ?Capital Projects and Construction ?Project Development and Planning ?Engineering ?Project management ?Construction management ?Consulting ?Process ?Business ?Environmental ?Technology ?Operational Services ?In-house engineering services for operations

May 1, 2009

The Century zinc-lead-silver deposit has a geological resource of 118 million tonnes averaging 10.2% zinc, 1.5% lead and 36 g/t silver. It lies approximately 250 krn NNW of Mt Isa in NW Queensland, Australia, and is hosted by middle Proterozoic age siltstones and shales of the Lawn Hill Formation. Within the orebody, most mineralisation occurs selectively within black shale units as fine grained sphalerite and galena lamellae with minor pyrite and siderite. The black shale units are separated by weakly mineralised sideritic siltstone horizons. The deposit is unmetamorphosed and only weakly deformed, displaying excellent lateral stratigraphic and grade continuity. The deposit is mostly overlain by younger Proterozoic sediments and later Cambrian age limestone cover and only a small proportion of the mineralisation crops out. Mineralisation has a subtle surface expression without a classic gossan profile, probably due to the low iron sulphide content of the ore. These factors contributed materially to the length of time between the first recognition of lead-zinc-silver mineralisation in the area by prospectors in the 1880s, to the discovery of the orebody by CRA Exploration Pty Ltd (CRAE) in April 1990.   Small scale prospecting and mining continued in the area from the date of the first mining lease in 1887. Post 1950, the deposit area was also included within nine separate regional exploration titles prior to CRAE's title acquisition in 1987. CRAE's original exploration strategy was partly pragmatically and partly conceptually inspired, but the eventual discovery only partly conformed to the original conceptual model. The deposit was found higher in the stratigraphy than the original target position, with unexpectedly low total sulphide content relative to other known deposits.   The discovery soil anomaly was located by the CRAE's first regional orientation traverse line in the area, but was not drill tested for three years. The discovery sequence at Century has strong elements of persistence, technical competence and some luck. It demonstrates that even in well explored terrains (by conventional standards) the exploration story can never be said to be over. The foreshadowed development of an economic resource at Century will hopefully inspire continued commitment to 'brownfields' exploration by mining companies, and demonstrate to external regulators the importance of genuine multiple land use strategies and the need for continued access to land for exploration and mining purposes.

Jan 1, 1995

By M Wilson, D Whiteman, P Kuiper, S Talu, G Watt, A van As

Once the draw process has begun in a block cave, it is very difficult to identify which regions of the cave have successfully propagated, where the caved material is flowing from and where it is flowing to. The uncertainty around cave flow increases as the cave is drawn and can be further compounded by poor draw control practices. These uncertainties make it difficult to plan effective draw strategies to control dilution, as flow model predictions tend to gradually diverge from the actual state of the cave. There have been documented occasions where observed caving phenomena, such as muck pile surface rilling, could not be reproduced with the cave flow models of the time. The ultimate consequence of cave flow uncertainty is generally manifest as higher dilution and lower grades.In order to measure the real-time flow of caved material within an active block cave, CRC Mining and Elexon have developed, together with Rio Tinto, a cave flow monitoring system called Cave Tracker, which is being trialled at Argyle Diamond Mine (ADM) in Western Australia. The Cave Tracker system at ADM comprises electronic ‘beacons’ that have been installed down long HQ diameter drill holes located above the extraction level. As the cave-back propagates and the rock mass fragments, beacons are released into the muck pile and flow along with the caved material to the drawpoints below. At Argyle, the beacons are configured to emit a signal every three days. These signals are picked up by detectors installed on the extraction and undercut levels, allowing the positions of the beacons to be determined.By examining the real-time material flow in different regions of the cave, flow mechanisms can be better defined. Draw control strategies can then be actively tailored to manage the current state of the cave. Thus, previously undetectable indications of excessive rilling, rapid cave propagation, cave stall, air gaps and dilution entry can now be identified early and assessed continuously as the cave progresses. For the first time it is possible to amend draw strategies based on measurements from inside and outside of the fractured zones, allowing caves to be managed more effectively.CITATION:Whiteman, D, Talu, S, Wilson, M, Watt, G, Van As, A and Kuiper, P, 2016. Cave Tracker flow monitoring system installation at Argyle Diamond Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 479–488 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications.

Jan 1, 1963

By L C. Taylor, H U. Lesiste

This paper describes a method for estimating the density distribution in the soil cap as a function of distance from its top at the time of impact with the target. It provides an estimate of the density distribution in the soil on the center line of the soil cap at the time of target impact for a single depth of burial of the charge and two heights of target and shows that, for the heights of target and the depth of burial considered, the thickness of the soil cap first increases from the in situ value and then decreases. The distribution of soil density along the centerline of the soil cap changes significantly with distance from its original position. These results can be used for validating hydro-code computations and the soil models used in the computations.

Jan 1, 2011

By B A. Tapp

The minerals industry in Australia is currently regarded as the country's economic saviour; the bastion of economic security. As Fitzgerald (1974) stated, 'Australia's natural endowments in minerals are the envy of most countries of the world'. As a result the proposed new mineral developments are on a scale that hitherto in the sixties would have been completely un-envisaged. It is reported that Australia is poised on the verge of a 16 billion dollar mining-based investment boom: a boom that will see Australia dominate the energy export field, the mineral processing field, and create the 'coal dollar'. This growth scenario has many inherent dangers, and it is the authors' contention that these should be carefully considered before further development proceeds. Two of the major problems related to the mineral industry growth scenario are the predictability of the future metal market, and the energy cost of mining. The latter problem is the one discussed here. The mining-mineral processing industries in Australia currently use about 36 per cent of Australia's primary energy budget. This large energy input is dominated by two major industries, iron and steel and the rapidly developing a1uminium industry. These two combined use over 20 per cent of the total Australian energy budget. In an industry which is export oriented about 96 per cent as expressed in ex-mine value terms û much of the energy input is exported along with the product. The authors therefore urge that serious consideration by the mineral industry be given to the relatively high energy intensiveness of process operations, especially in respect of the aluminium industry.

Jan 1, 1980

By Ö. Erdem

The investment decision making process in the insurance and finance industries is affected by new advances such as simulation techniques. These advances have improved the discounted cash flow method (DCF). In DCF, a dynamic and flexible model construction is not possible because it does not consider uncertain conditions. Each project should be evaluated taking into account the related uncertainties because the related uncertainties determine the characterization of the project. Related uncertainties can be processed in dynamic DCF, which is applicable to both financial and non-financial industries with different kind of uncertainties, such as power generation and petroleum projects. The dynamic DCF method can estimate net present value (NPV) while managing related project uncertainties with a simulation method like Monte Carlo Simulation. The simulation method is preferred because its output is unbiased. Therefore, a more realistic financial evaluation of the project can be concluded. In spite of the improvement of dynamic DCF, this project evaluation method is not used frequently in mining industry. However, the mining industry is ideally suited to this concept because it is highly dependent on estimations such as orebody size and ore grade. During the project evaluation stage, these uncertainties can be included with the dynamic DCF method. This study aims to contribute to increasing the usage of this method in mining projects. A copper reserve in Turkey is selected as a case study to apply uncertainty assessment for the evaluation of NPV.

Jan 1, 2012

By S. Asokan, D. Rathod, Ch. V. G. K. Murty

Tata Steel, a steel arm of Tata Group, is Asia's first and India's largest integrated private sector steel company. Tata Steel’s turnover in fiscal 2004-05 was nearly US$ 3.25 billion. As part of its vision to grow in related industries, Tata Steel is poised to enter the Titania businesses in the Indian state of Tamil Nadu. The Titania project will involve mining, separation of ilmenite & other co-minerals, beneficiation of ilmenite to synthetic Rutile and further maximum value addition to Titanium metal. This paper outlines the journey from the concept to current findings of the Bankable Feasibility Study in developing Sattankulam Heavy Mineral Sands Deposits in the State of Tamil Nadu, India by Tata Steel.

Jan 1, 2005

Several industrial-scale HydroFloat separators have recently been installed at Mosaic?s South Fort Meade beneficiation plant for the purpose of improving phosphate recovery and throughput capacity. This technology was implemented after numerous laboratory, bench-scale and on-site, pilot-scale test campaigns. The results from this detailed test work provided sufficient justification for the complete retrofit of the existing coarse and ultra-coarse flotation cells. Data indicate that the metallurgical results obtained with the full-scale separators are consistent with that obtained during both the bench- and pilot-scale evaluations. The benefits, theory of operation and commissioning of the equipment are also discussed.

Jan 1, 2007

By J. P. Kennedy, O. A. Bascur

Large metallurgical complexes have more data than a small city and these data change as internal and external conditions evolve. Staffing turnover hinders experienced-based decisions especially with simple tools like spreadsheets. Lack of current information can contribute to decisions that result in significant deterioration in the quality of operation. Timely, unified information from sophisticated analyses presented to the broadest possible reach will improve operation. The major innovation is the addition of the web browser to the suite of software people will use with no training – the other two are spreadsheets and graphical presentations – and the consistent organization and transformation of the real time data to support broad access. This paper describes the data transformations and presentation methods necessary for a Web view, especially the special needs of real time data and analysis required for active operations decision-making. Many people inside and outside the complex, not just operators, need timely information that is abstracted, aggregated, organized and unified. Unification and aggregation of real time data presented via the Web opens a new paradigm for collaboration. The analysis tools are as important as the data. These rule-based tools add significantly to the operations database in the form of results stored for viewing with plant data. Mining and metallurgical plants already use many sophisticated analysis tools such as predictive maintenance policies based on statistical analysis vibration analysis, and oil and lube analysis for critical equipment. These add real time events, similar to an alarm package, and unified production information to the operational database. Simple models are used on line to create key indices that provide a real time indication of performance. Key indices include metrics for losses due to plant availability, performance efficiency, and overall process equipment effectiveness. These additional data in the operations database are used for early fault detection, increased production, better quality, higher availability of equipment and faster detection of process bottlenecks. An important feature is the ability for people to create their own key indices and store the results for use by anyone in the plant historian, but accessible by a browser. Keywords: plant information, principle components analysis, data reconciliation, gross error estimation, Internet, Word Wide Web

Jan 1, 2002

By E. D. Gardner

This is one of a series of paper's being published by the Bureau of Mines on placer mining; it is written as a supplement to Information Circular 6788, "Placer Mining in the Western United States, Part III", by E. D. Gardner and C. H. Johnson which was published in February 1935. Since Information Circular 6788 was written (1933), considerable advance has been made in the technique of mining placer gravels with power shovels and draglines. Although new washing plants continue to be built in accordance with untried designs the trend of new installations is toward proved equipment. A substantial number of plants are now being operated successfully (1937).

Jan 1, 1938

South Africa remains the largest global producer of gold, accounting for 11.3 per cent of total world mine production, which amounted to 2520.2 t in 2005. The benefits and disadvantages associated with hedging practices in general, and among South African gold producers is examined. The wide variety and unique nature of risks faced by the mining industries provide a strong case for hedging. Only the principles of hedging, such as selling ounces of gold in the ground at a pre-agreed price for delivery at a future date as a cost-effective mechanism for price risk management, is discussed. Progressive and cumulative increases in the volume of forward sales in the major producing countries are considered by many to be the cause of the declining gold price over the past decade. In spite of negative publicity, forward selling continued as an industry-wide practice until recently (2002) when the global hedge book contracted by 352 t; contraction amounted to 158.6 t in first quarter of 2006. The objectives and benefits of hedging include continuity and stability of cash flows, stability in price achieved, reduction of frictional costs, and creating an effective management tool. The importance of a defined hedging strategy in reducing uncertainty about the hedging objectives is essential to a successful hedging policy. Historical patterns in hedging revenues at an industry level indicate five distinct periods during which the fortunes of hedgers have fluctuated. Finally, since 2001 the rising gold price and reduced price volatility through the consolidation in the global price means that the need to stabilize revenue flows is less urgent. This has meant that hedging is becoming progressively less important for the mining industry at large.

Jan 1, 2007

By J. H. Zietsman

It has previously been observed that industrial high-titania slags display a compositional invariance, remaining close to stoichio-metric M3O5. The present study focuses on this invariance and the phenomena which may cause it. The invariance was studied using thermochemical calculations and a mechanism is proposed for the observed behaviour. The mechanism suggests that a combination of thermochemical equilibrium and transient slag solidification and melting results in the observed compositional invariance. The proposed mechanism provides new insights and prompts questions about other mechanisms in the smelting process.

Jan 1, 2004