Search Documents

By Stephan Großwig, Karolina Nycz, Arne Kindler

"Commonly used anchor monitoring systems are mainly based on the use of anchor force meters. However, experience shows that the reliability of the display of force meters lowers over time. Other measurement and test methods like for example fibre bragg grating method require a comparison with an unloaded optical fibre and give only selective information about the bearing behavior. Moreover the obtained information has to be interpreted. In the following article, first measuring results of an anchor monitoring system based on measurements with optical fibre are presented. The new monitoring system is based on the Rayleigh technology and was used to test the load bearing behavior of the anchor grout body as well as for the evaluation of the grout body condition in concrete-damaging groundwater.INTRODUCTIONThe first fibre optic sensors came onto the market about three decades ago. Initially used as special solutions only in selected cases, now they have found use in almost all areas of technology, especially in areas, where electrical sensor systems reach their limits. The first application examples of spatially resolved fibre-optic sensors in the field of geotechnics have been in existence since the mid-1990s, in projects such as the assessment of the of radioactive repository location sites (Hurtig et al. 1994), for the monitoring of landfill sealing systems (Hurtig et al. 1995) or within the framework of the rehabilitation of mountain farming landscapes (Schreck et al. 1998).The company's first own works in the field of glass fibre measurement technology have been in existence since 1993. The first carried out projects were a monitoring at the Edertalsperre (Dietz et al. 2001), a monitoring with glass fibre tendon at a flood bridge in Carinthia as well as monitoring within the framework of the Storebælt crossing. In all cases, the structure was permanently monitored by means of individual-point measurements. Since 1993 various fibre-optic sensor solutions for geotechnical applications have been introduced to the market (Voet, Glötzl 1996, Hurtig et al. 1994)."

Jan 1, 2017

By Kerry Gee, Gary Colgan, James Fricke

Introduction Elevated zinc concentrations are observed in groundwater within alluvium adjacent to Silver Creek east of Park City, Utah. The study area is located in a small valley one and one-half miles northeast of Park City, Utah in Summit County, Utah (Figure 1). Although surface water concentrations in Silver Creek are typically less than 1 mg/l, groundwater concentrations have been measured as high as 85 mg/l in a near neutral pH environment. The elevated zinc concentrations in groundwater result from several factors including: (1) dissolution of zinc from tailings exposed at the surface and within the alluvium, (2) oxidizing conditions created by surface/ground-water exchange, and (3) ideal geochemical conditions for the dissolution of zinc-containing minerals. These ideal conditions include readily soluble minerals, available anions for complexation, and lack of available surface adsorption sites.

Jan 1, 2005

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By R. T. Jones

Base metals and platinum group metals can be collected in metallic alloy form, via a wide variety of smelting processes. The recovery, or degree of collection, of the valuable metals is a function of the extent of reduction in the furnace, which, in turn, is indicated by the fraction of iron present in the feed materials that report to the alloy. An equation has been developed that relates the recovery of various metals (such as Ni, Co, Cr, and PGMs) to the recovery of Fe. This recovery equation (for each metal) is characterized by a single parameter (K?) that can either be empirically fitted to the data, or expressed in terms of the equilibrium constant and the ratios of the activity coefficients involved. Data from a number of varied DC arc furnace campaigns are presented to illustrate this behaviour.

Jan 1, 2009

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By R. Chen

Most tunnels built in Sydney encounter similar ground situations; they penetrate either the Hawkesbury Sandstone or the shales that lie beneath the city. Tunnels in these materials are generally sup-ported by rock bolts in combination with a shotcrete lining. A method of analysis is presented to improve our understanding of the long term behaviour of fiber reinforced shotcrete (FRS) materials and the tunnel support systems. A finite element method SAFEA (Semi-analytical FE Analysis) is developed to model the combined creep behaviour of a shotcrete lining and the Hawkesbury Sandstone. To model the time-dependent creep behaviour, the bulk modulus and shear modulus of the materials are represented by logarithmic functions in time. A Laplace transform is then applied to these functions of time and the solution of the problem found from a finite element analysis. Tablot?s method is then used to invert the transformed values and find the solution in real time. The time dependent creep deflection of the numerical tunnel models reflects the interaction of the shotcrete lining and rock which have different creep parameters.

Jan 1, 2008

Macraes Mining Company Limited operates a 2.1 million tonnes per annum gold processing plant at Macraes Flat, Otago. This uses a conventional CIL route to treat oxide ore, and a flotation, grind, CIL route for sulfide ore. This paper describes the design and operation of this process plant.

Jan 1, 1992

By H. R. Beard

The Federal Bureau of Mines investigated the absorption of radium and thorium from waste uranium leach liquor by clays and other materials. This work was conducted in support of the Bureau's goal of minimizing the environ¬mental conflicts, impacts, and occupational hazards Associated with mining and mineral processing operations. Tailings and soil samples from Wyoming and Utah were contacted with tailings liquors to determine the degree of absorp¬tion. Absorption ranged from 0 to 99 percent for radium and from 0 to 31 per¬cent for thorium. Some samples, which readily absorbed radium, were contacted with various salt solutions that could be present in tailings solutions to determine their effectiveness as desorbents. The desorption of radium ranged from 0.06 to 100 percent. An alpha-spectrometric method was used to determine the radium and thorium, concentrations in the solutions and the solids.

Jan 1, 1979

By Bowen Li

Andalusite is an excellent raw material for refractory applications due to its high aluminum oxide content and phase transformation to mullite at high temperature. Granular andalusite in particle sizes of about 1 to 2 mm was traditionally utilized for the manufacturing of refractory brick. However, if powder andalusite in micron particle size is utilized in high-alumina refractory products, reinforcement on the refractory brick can be obtained and the sintering temperature can be decreased. The phase transformation of powder andalusite plays a key role for the difference.

Jan 1, 2006

Let’s start off with your assessment of the mining industry. Today, the status of the mining industry is stronger than it has been over the previous few years. While mining continues to be a major part of the world’s economic foundation, the industry is gaining strength due to rebounding metals and minerals prices. And now, with these rising prices and the changes the industry instituted during the years when mining-related commodities were selling at low prices, our stronger, more productive and internationally competitive industry should flourish. Mining remains an essential business and the industry is far ahead of the game when it comes to the trend of globalization as a key to sustained growth. Also, the industry continues to realize increased productivity through technological innovations. And an increasing number of countries are moving towards capitalism, which opens doors for exploration and mining within their borders. After looking at all of these factors, I believe that the mining industry will only continue to gain momentum in the future.

Jan 1, 2004

By Y Ren

?ptim?sgtion t?ols nos ope? 0iu ?ingc s?ch as the cche??ling and?pi? k?(i?isatTon tool{ ?ave bg?ome(?osd-dvfective way? to e?iluata open`¦it mi~e!p?n?ept as w?ll asá?}prmv?ng mine?projecW`value> ?owerez

Aug 12, 2013

By John M. Dale

Now that the price of sulfur has reached unexpected high levels, it is little wonder that sulfur from surface ores is again receiving attention. In most instances, it is advantageous for an ore to be at or near the surface. However, it is a distinct disadvantage for sulfur ore to be close to the surface because it precludes the use of the Frasch process. The Frasch process depends on the presence of at least 180 m of uniform overburden to allow pressure injection of superheated water into the sulfur-bearing formation to melt the sulfur. In the Frasch process, sulfur separates cleanly from the gangue underground and comes to the surface in a very pure form. Surface sulfur deposits, particularly those in the Western Hemisphere, exist largely due to volcanic activity, and sulfur separation from the gangue is a formidable technical problem. None of the surface deposits are large compared to some of the Frasch deposits, but at the present sulfur price, they are certainly of economic importance. From the turn of the century until 1975, the price of sulfur was for the most part $18-$28/t. However, with the price of sulfur now over $154/t, there are a variety of technical alternatives to consider for sulfur surface ore separation that may not have been economically attractive a few years ago.

Jan 9, 1981

By N. F. Mescheriakov

New mechanical and pneumatic-mechanical flotation machines with axial impellers have been developed. Industrial tests show that these machines ensure lower power expenditure (on flotation) by 1.5-2.0 times as compared with reference machines (with the same or improved technological indices). Application of the newly developed axial impeller, with these advantages, is possible in any volume chambers of type OK, Dorr-Oliver, Wemko etc.

Jan 1, 1998

By D. Imeson, T. Grammatikopoulos, M. Aghamirian, M. Oliazadeh

"More than 70% of potash is produced worldwide by froth flotation. Flotation of potash was developed in the early 1930s. Amines are widely used for flotation of sylvite (KCl) from halite (NaCl) and insoluble materials such as clays. Amine collector is also absorbed by clays. Therefore, clays are usually separated by scrubbing and de-sliming prior to flotation. Alternatively, slimes can be floated ahead of potash flotation. Flotation recoveries of sylvite are commonly in the range of 85%, while losses can occur in slimes, flotation tailings and make-up of process brine. Ores containing free coarse-grained sylvite are generally screened, whereas both fine and coarse fractions are conditioned and floated separately. The unique features of potash flotation include solubility of sylvite in water, the size of particles floated and fast kinetics. Particles up to 2.3 mm can be floated and about 50% of flotation feed can be removed in the rougher stage in few minutes. The main challenges in potash flotation are the recovery of potash from slimes, flotation efficiency in the presence of carnallite and recovery of coarse potash grains. A review of potash flotation shows that there is still room for improvement in both coarse and fine potash flotation. The present paper reviews the most significant flotation parameters including reagent type and dosage, flotation circuits, flotation equipment size and new developments in potash flotation. The latter include new reagents, flotation technologies (Hydrofloat, Jameson and column cells) larger flotation cells and slimes flotation.INTRODUCTION Potash is the common industrial term for potassium in various chemical combinations and minerals soluble in water. About 90% of potash produced worldwide is used as agricultural fertilizers. Flotation is the main treatment process of sylvinite (KCl-NaCl) ores for recovery of sylvite (KCl). Potash concentrate should contain a minimum of 95% KCl and be relatively free from 0.2 mm KCl fines. The flotation process for beneficiation of potash ores was developed in United States and Russia concurrently in the early 1930s. In 1934, Potash Corporation of America applied flotation process in a commercial scale (Tippin R.B. and Huiatt J.L). In the initial application, halite (NaCl) was selectively floated by employing lead chloride as an activator and soap as collector. The sylvite concentrate was reported in the cell underflow."

Jan 1, 2012

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By B. O. Odera

The Pt-based alloys have a high potential for replacing some Ni-based superalloys (NBSAs) used in the highest temperature and most aggressive environments, and vanadium would be a beneficial alloying element. Six alloys of average compositions Pt-26.6Al-9.1V, Pt-23.1Al-17.8V,Pt-9.6Al-21.1V, Pt-17.4Al-6.4V, Pt-22.3Al-7.9V, and Pt-6.0Al-10.1V (all in at.%) were manufactured by arc-melting and examined in the as-cast condition using scanning electron microscopy and X-ray diffraction (XRD). Five samples were heat treated at 1 000°C for 1 500 hours and water quenched, then examined. The phases were identified using energy-dispersive X-ray spectroscopy and the identities were confirmed by XRD. In most of the samples, the phases existing in the as-cast condition were different from those at 1 000°C after ~1500 hours heat treatment. A solidification projection, an isothermal section and a liquidus surface projection were determined for the Pt-rich corner.

Jan 1, 2012

By T. P. Williams, M. B. Rydzewski, B. Corner

Konkola Copper Mines (KCM) plc is an integrated copper producer operating on the Copperbelt in Zambia. KCM has numerous mining operations located in the towns of Chililabombwe (Konkola Mine), Chingola (Nchanga Open Pit and Underground operations), Lusaka (Nampundwe Mine), with a smelter located in Kitwe (Nkana Smelter) and an SX-EW plant in Chingola (Nchanga Tailings Leach Plant). [ ]

Jan 1, 2005

By A. P. N. Sutherland

Pipelines for transporting high concentration slurries are often designed using methods applicable to homogeneous non-Newtonian laminar flow. Many industrial slurries though comprise coarse particles in a non-Newtonian carrier fluid, and existing experimental evidence from tests with such slurries demonstrates that they are not homogeneous. Under laminar shear conditions the coarse particles settle, even in statically stable carrier fluids. To understand this better, the Institute of Materials Science and Technology (IMST) at Cape Peninsula University of Technology (CPUT) is conducting ongoing research into the flow of these high concentration non-Newtonian settling slurries. Since pressure gradient and flow rate measurements alone are insufficient to adequately model the flows, an electrical resistance tomography (ERT) instrument developed by the University of Cape Town (UCT)was incorporated into the pipe test loop to determine pipe cross-section concentration and velocity profiles. The software developed to do this is modular and allows different image reconstruction and cross-correlation algorithms to be implemented and tested without significantly changing the rest of the application. At a total frame capture rate of 566 frames/sec a 2.67 GHz Intel Celeron processor with 500 MB of RAM is fast enough to calculate and display velocity profiles in ?real-time? at an update rate of one profile every two seconds. Examples of experimental concentration and velocity profiles obtained using the system are shown and some proposed improvements/extensions to the system are listed.

Jan 1, 2008

By E. T. Turkdogan

Jan 1, 1962

By Martin Herrenknecht

Tunnel boring machine (TBM) development continues to take on not only larger diameters, but also more difficult ground conditions. Ground conditions consisting of unstable faces with water pressures up to 15 bar have required innovative design approaches. A systems approach has been required to produce tunneling machines that can safely excavate the tunnel in an efficient, cost-effective manner that stresses production and labor saving approaches. This article reviews the current design developments and present recent projects where these most recent principles have been applied. The world?s growing population and rapidly proceeding urbanization are boosting an enormous demand for new and high-capacity infrastructures to secure the mobility of goods and people. Densely populated areas face the challenge of providing efficient traffic infrastructure such as a modern public transport system. At the same time, the maintenance and modernization of supply and disposal structures for water, sewage, energy and communication are essential. Last but not least, are supra-regional transportation routes such as long distance water diversion schemes. All of these projects are as demanding and are characterized by a tight time schedule. In this context, the demand for efficient tunnels for traffic and utility lines is increasing, as new infrastructures often leads underground because of limited space above ground. Also, tunnels are the obvious choice to cross natural barriers like mountain ranges. To handle the complex and variable geological conditions and other constraints, such as low overburden, high water pressure or long tunnel drives while facing increasing demand of a quick completion of a project, mechanized tunneling sets standards regarding safety, profitability and environmental protection in traffic tunneling projects as well as in the trenchless construction of utility tunnels. Different machine types and working principles have been developed to master various geological and hydrogeological requirements. Continuous activity in research and development leads to constant improvement of the mechanized tunneling process.

Jan 1, 2008