Search Documents

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

A process was developed to produce electrolytic manganese dioxide, suitable for use in high quality dry cells, from Risdon anode mud. ImpurItIes present In the anode mud were removed prior to the electrolysis which was performed from a manganese sulphate bath using the following conditions.Temp. 95°CH2S04 50-55 g/l.Mn2+ 55-60 g/l.Anode c.d. 10·0 A/sq. ft.Operation under these conditions yielded current efficiency and power consumption figures of 95 per cent and 0·8 kWh/lb respectively. The product conformed to battery manufacturers' specifications as regards physical and chemical properties and performed satisfactorily in a battery testing programme.

Jan 1, 1968

By Monique Pharand, Jeet Basi, Simon Hille

"High quality activated carbon is essential in the recovery of gold in Carbon-in-Leach (CIL), Carbon-in-Pulp (CIP), and Carbon-in-Column (CIC) circuits. Goldcorp’s Campbell complex at Red Lake Gold Mines (RLGM) experienced a period of low soluble gold (Au) recoveries during Q3 2013, during which time the processing plant saw higher than typical Au grades in the CIP tails solution stream. A technical review identified that the CIP circuit may be experiencing a carbon-fouling issue. To further understand the degree of fouling, and to troubleshoot the low recovery problem, samples of carbon were collected from the CIP, elution, acid wash, and regeneration circuits, and submitted for characterization test work. This paper summarizes the steps taken to remedy the carbon-fouling problem at RLGM resulting in increased overall Au recovery.Overview of Red Lake Gold MinesRed Lake Gold Mines is located approximately 450 kilometres northeast of Winnipeg, Manitoba, in Ontario’s western boundary region.All mining is carried out through underground operations, utilizing overhand cut and fill, underhand cut and fill, and long-hole mining methods. Ore types include: silica-replaced carbonate veins with free milling gold, siliceous replacement-type mineralization (rich with arsenopyrite) marginal to veins, broad disseminated sulphide mineralization along major shears, and some minor sulphidized chemical sediment-hosted ore. The operation is supported by two milling complexes: Red Lake, and Campbell.Process DescriptionThe Campbell processing plant's main unit operations consist of grinding, gravity concentrating, flotation, autoclaving, leaching, carbon-in-pulp (CIP), carbon elution and reactivation, electro-winning, bullion smelting/refining and cyanide destruction, and concentrate handling. A schematic of the plant flowsheet is shown in the figure below.BackgroundHigh quality activated carbon is essential in the recovery of gold at many CIP/CIL/CIC processing plants. At RLGM, gold-bearing ore is milled and cyanide is added to leach the gold from the solids into solution. The dissolved gold then comes into contact with activated carbon, and adsorbs onto its highly porous surfaces. Gold is then recovered by separating the activated carbon from the main slurry for further refining. As such, the characteristics and quality of the activated carbon have a significant and direct impact on overall gold recovery."

Jan 1, 2016

By Éric Poulin, Simon Gariépy, Mario Paredes Malca

"While the design of a control strategy depends on the available process knowledge, its implementation depends on the available process information. On-line chemical analyzers are today widely spread in the mineral processing industry. A real-time concentration measurement of chemical components is valuable information that could bring control strategies to whole new levels. However, the use of these measures rarely reaches anything more than process monitoring. The reason is simple: the on-line chemical measurements quality is most of the time insufficient to be directly included in control strategies. The choice is then made to let the critical eye of the engineer or the operator appreciates the measurements before making any decision based on it.Data reconciliation through mass balance is a technique today widely used in the mineral processing industry to increase the accuracy and the reliability of plant data, mainly for accounting and survey analysis purposes. Real-time data reconciliation of on-line measurements appears as a natural coupling of technologies that could bring new process optimization trends. Once overcome the technical difficulties, full valorization of the instrumentation investment could be reached.This paper presents the application of real-time data reconciliation for process control and performance monitoring. It proposes a general approach, discusses challenges and illustrates concepts with industry experiences."

Jan 1, 2006

By Bratt G. C

When zinc is electrowon from concentrates or residues of high manganese content, the zinc sulphate electrolyte may contain high levels of manganese. The manganese level is usually controlled by removal of manganese at the anode as the dioxide during the zinc electrodeposition stage.By increasing the temperature of an electrolyte containing 8 gll manganese from 35°C to 90°C, decreasing the acidity from 100 gll to 30 gll, reducing the current density from 432.A.m-2 t6 286 A.m-2 and using new lead anodes containing over 0·75 per cent silver, the current efficiency for manganese dioxide removal was .increased from less than 1 per cent to over 20 per cent.At the same time the current efficiency for zinc deposition was maintained above 90 per cent by additions of high molecular weight cationic polyacrylamides to the cell. By utilization of these conditions in a small number of cells, the manganese level in the circuit could be economically concrolled to any desired level.With these conditions the formation of the dioxide changes from an indirect route, via Mn04-, to a direct oxidation of Mn2+ to Mn02.The incorporation of impurities such as Pb, K, NH4, Cu, Ni, or Fe makes the deposit unsatisfactory for direct use in Zn - Mn02 dry cells. The deposit structure changes from cryptomelane at low temperature to y3-Mn02 at high temperature.

Jan 1, 1975

The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are: 1) Line Drilling 2) Cushion Blasting 3 Smooth Wall Blasting 4) Buffer Blasting 5) Presplitting or Preshearing 6) Air Deck Presplitting

Jan 1, 1992

By Rolf Schillinger

Blasting activities on the surface or underground necessarily involve the most sensitive aspect of environment remediation, human response or annoyance. Such effects are unavoidably characteristic of those activities. For this reason, blasting activities are governed by law and official regulations under surveillance of authorities, where companies and explosives engineers have to proceed within proper limits. Subject of the paper is a practical way of handling some necessary vibration standards being focused on blasting activities. The paper is based on the German Standard DIN 4150, Part 1 - 3, “Vibration in buildings”, Part 1: “Prediction of vibration parameters”, June 2001, Part 2: “Effects on persons in buildings”, June 1999 and Part 3: “Effects on structures”, February 1999.

Jan 1, 2006

By S. Weiss, E. Espinoza

The El Sauzal gold-silver deposit is a high-sulfidation, epithermal precious-metals deposit hosted by an east-dipping sequence of dacitic and rhyolitic pyroclastic and debris-flow units of probable Oligocene age. Total gold production since startup in late 2004 is approximately 450,000 oz. of gold. Above the sulfide boundary gold is mainly disseminated as small grains interstitial to alunite, kaolinite and quartz. The majority of the ore is found in quartz-alunite-kaolinite altered rock that mantles tabular to irregular silicic cores of vuggy, residual quartz ±kaolinite ±dickite. Grade domains are modelled as subhorizontal to east and southeast-dipping. Higher-grade domains cut across alteration zones and also coincide with transitions from vuggy quartz to quartz-alunite-kaolinite. The highest grades are commonly found marginal to vuggy quartz in transitional, hematite-rich quartz-kaolinite and quartz-alunite-kaolinite rock.

Jan 1, 2007

By James Diekmann

The Disputes Potential Index (DPI) is a computer program designed to help team mem¬bers assess the likelihood of contract disputes on a construction project. The program's predictions are based on data from 159 construction projects that encompass a variety of public and private projects. The impact of three categories of project characteristics are included in the DPI program, specifically, people, process and project characteristics. Ultimately, DPI returns an overall project score that indicates the likelihood of exces¬sive contract disputes. The output of a DPI analysis can be used as part of a contract readiness review or to define the need for extraordinary dispute avoidance procedures. This paper examines the development of DPI and presents the results of DPI analyses on several tunneling projects.

Jan 1, 1995

By A-A Latscha, C Boyle

Geological modelling has historically been done using sectional interpretation of paper sections or on a computer screen. Boundaries of geological units or grade shells are interpreted by a geologist section by section and the shapes are drawn onto paper to be digitised later or they are directly digitised into a computer. This approach is referred to as explicit modelling. Such methods are time consuming if there are many section lines or boundaries to be interpreted. The number of metres drilled and resource models made is increasing each year and it will be difficult to keep up using explicit modelling methods. Alternatively, it is possible to use information carried in the drill holes, known geological relationships and point estimation methods in two or three dimensions, to create similar geology boundaries, while eliminating or at least greatly reducing the need to manually interpret and digitise detailed sectional interpretations. Such methods are referred to as implicit modelling and are available in a number of software packages. Implicit modelling approaches have been used in iron ore and found to significantly reduce the time needed for modelling while producing results that are comparable or better than standard explicit modelling approaches. A number of case studies have been undertaken of implicit modelling in iron ore deposits. Stratigraphic surfaces of bedded, folded and faulted iron ore deposits have been modelled in various deposits by Leapfrog Geo, GOCAD (with SKUA) and Vulcan Integrated Stratigraphic Modelling. Leapfrog Mining was used to model iron grade shells at particular cut-off grades. The modelled surfaces are of a high standard equivalent to those that could be produced by traditional explicit modelling but the time required by the implicit methods is far less. Implicit geological modelling is an active area of software development and improvements in software are likely.CITATION:Boyle, C and Latscha, A-A, 2013. Implicit geological modelling of iron ore deposits, in Proceedings Iron Ore 2013 , pp 57-66 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

By Keith Schaeffer

This paper presents a history of the planning, engineering and construction completed for the railroad tunnel crossing part of the West Elizabeth Avenue Storm Drainage Project, undertaken to relieve flooding within the West Elizabeth Avenue area in Linden, NJ. The Railroad Crossing Contract is part of the larger Linden Drainage Improvements Project consisting of a new gravity storm sewer system. The improvements are required to provide additional storm drainage for the City of Linden and the Merck Pharmaceuticals manufacturing facilities in the City of Linden.

Jan 1, 2008

By Michael Alber

Coal mining by the longwall method typically causes seismic events. This paper describes the research on mining induced seismicity around two specific longwalls at 1100m depth under several old longwalls. A local network featuring 21 geophones has been installed, underground core drilling and an extensive rock testing program were executed. A rock mechanical model featuring a multi-layer strata was created for use with numerical analyses. Seismic events were localized and three different event types are described. Focal analyses yielded distinct modes of failure. Those types are explained by different failure mechanisms, namely fault activation, remnant pillar punching and beam failure. The use of rock mass classification, rock mass strength criteria and in situ stresses together with 2D and 3D numerical analyses allows evaluating the findings from seismology approaches. Conclusions are drawn that the orientation of longwall with respect to the major horizontal stress orientation plays an important role in mine induced seismicity.

Jan 1, 2008

By Tom Pfitzer, Alice Correa, Meredith Hardwick

The past decade has brought significant changes in the use of risk-based criteria for safety within the U.S. Department of Defense. The Range Commanders Council (RCC) chartered a working group to develop and define risk acceptance criteria for protecting the general public and mission essential personnel from debris from launch ranges. This working group has continued to develop and update RCC Standard 321 as the needs of the ranges and range users have evolved. A revision to RCC Standard 321 is near finalization and will include casualty criteria, guidelines for assessing risks due to other flight hazards in addition to inert debris, and an overall risk management process for range safety. This paper reports on work in progress and includes several precedents which may prove important to the explosives safety community.

Jan 1, 2007

By Giannini M

Of the optimization techniques proposed in determining the optimum open pit limits, dynamic programming and graph theory have proved most successful. However, publications on these two methods lack a certain amount of rigour and clarity in exposition. Certain ideas in the methods have been clarified and additional features introduced in order to make them more sensitive to practical applications. A case study in the form of an application of these ideas on data from a producing mine is presented and discussed.

Jan 1, 1986

By Antonio Pineda, Roger K. McLimans, Felicity E. Lloyd

lmenite is a primary ore feed to the DuPont chloride process for the manufacture of titanium diox-ide pigment. We seek to determine ilmenite geochemistry as a function of original source and as-certain which ilmenites have chemistry most amenable to upgrading via iron-leaching (leucoxenization) and that have favorable, with respect to pigment manufacture, trace element content. Ilmenite geochemistry is a function of its primary origin and of subsequent alteration. Heavy mineral sand deposits may contain ilmenite from one or several dominant source rock(s). In addition, ilmenite may alter in the weathering environment, changing the major element compo-sition (iron-leaching) and certain of the minor element content. A primary objective is to classify ilmenites in relation to origin in order to fingerprint source rocks in provenance determination. The changes in trace element chemistry during alteration are also investigated. A “decision tree” is developed to classify ilmenite types and source rock origins. Ultimately, with those methods and by amassing a database of ilmenite types from worldwide locations, it should prove possible to determine ilmenites (and their sources) more susceptible to iron leaching in the weathering en-vironment. Such ilmenites, enhanced in their titanium content, are the preferred ore targets. The method used is electron microprobe analyses at elevated conditions of voltage, cur-rent, and counting time to enable higher precision. In-situ ilmenites from igneous, metamorphic, and altered rocks (saprolites) are analyzed. Initial foci for sedimentary ilmenites are restricted provenance (approaching monogenetic, examples from Spain, Portugal) and polygenetic prove-nance (Denmark). Altered ilmenites, including the DuPont Florida ore, are used to characterize the chemistry of leucoxenization. Trace element concentration, detectability, and cost considera-tion, led to focus on Mn, Mg, V, Cr, and Nb to develop a classification scheme validated by dis-criminant analysis and “classification-regression trees”. Results show a high degree of success for restricted provenance study and an acceptable one for polygenetic provenance.

Jan 1, 2005

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By Junfeng Shen

Geosynthetic clay liner (GCL) is a kind of waterproofing material used widely in engineering. The waterproof mechanism is understood in terms of bentonite particles becoming a water-obstructcolloid layer after they absorb water and swell. The swell stress, however, has not been determined directly till now. In our experiment, the swell stresses of the GCL under saturated and water absorbing conditions are measured directly using a custom-made instrument. The results show that (1) the instrument designed by the authors performed satisfactorily and the test results are reproducible; and, (2) The trend line of swell stress variation with time can be divided into three segments. The first segment is characterized by a quick increase of the swell force in the first 0?50 hours. The swell stress increases by 7.00×10-4?1.00×10-3 Mpa / hour. The second segment shows a slow increase of the swell stress during the 50?1730 hours. The swell force increases by 7.54×10-6?2.02×10-5Mpa / hour. The third segment is characterized by little variation in the swell stress after 1730 hours. In this segment, the average value of the swell stress measurements is 0.0719Mpa and the maximum value is 0.0729Mpa. It is suggested that the swell stress is mainly raised by water entering the pores among montmorillonite particles and the interstitial layers in individual montmorillonite crystals, leading to an increase in volume and manifested as a stress on the surrounding materials.

Jan 1, 2006

By R. E. Chaves

San Martin Mine is an open pit, gold heap leach operation located approximately 70 kilometers from the Honduran capital of Tegucigalpa. Mining operations commenced in 2000 and were completed late in 2007, while heap leaching operations continue. Reclamation was executed concurrently with operations to the extent practical. The area has distinct rainy and dry seasons and closure objectives include: prevention and mitigation of acid rock drainage, sediment and erosion control, and mitigation of visual impacts. Final closure is well underway at San Martin and this paper describes the closure processes conducted to date, problems encountered, and the subsequent lessons learned.

Jan 1, 2009

By A. K. Anyimadu

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004,and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November 2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Keywords: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, platinum, palladium, PGMs, tailings.

Jan 1, 2007