Search Documents

By Robinson KJ

Education in Australia now has to respond to a very wide political and policy agenda. The political emphasis is upon increasing participation and retention rates with a view to greater graduation rates in `high-tech' disciplines. There is an implied linkage between `education' and `economic well-being'. Our argument is that equalitarianism in education tends towards mediocrity. In this context many Geoscience educators view the future with pessimism. The argument is that science has been `sold short' and needs revitalising. We contend that Geoscience coursework should be a feature of both secondary and tertiary education in Australia. To this end we propose six policy initiatives to increase the content of Geoscience in education programmes.

Jan 1, 1989

With the dawning of a new century came the beginning of a new era in the coal industry. Instead of the traditional practice of only buying and selling produced coal in the United States, a coal futures market was established. The New York Mercantile Exchange began trading coal futures in July 2001. But, even in this new era, many of the old is-sues that have beset the coal industry still remain, as was evident in2001. Coal production increased to are cord level during 2001, according to preliminary data from the US Energy Information Administration(EIA). Production in 2001 rose by4% to 1.01 Gt (1.12 billion st), compared with 2000 (Table 1). This barely surpassed the previous record level of 1 Gt (1.11 billion st)set in 1998. Coal consumption remained unchanged. The additional production was used to replenish the depleted stockpiles that had resulted after two years of declining coal production and increasing coal consumption.

Jan 1, 2002

By H. M. Chikashi

Keywords: Pyrometallurgy, furnace, bath agitation, regression analysis, entrainment This paper presents the results of linear regression analysis of the influence that each component of slag has on the losses of copper in slag-cleaning-furnace slag. Data used for the analysis are actual plant data collected over the past two years of operation. Facts obtained from the study will be helpful for smelter management to control these components in the flash smelting furnace feed and slag, to levels which will enable better control of copper in slag, and smoother operation of the KCM slag-cleaning furnace.

Jan 1, 2011

By Misra V. N

Davis tube tests were conducted on a Koolanooka magnetite iron ore sample, supplied by Kingstream Steel Ltd, to determine the optimum grind size, maximum iron recovery and the cleanness of the products from low intensity magnetic separation (LIMS). The ore sample contained 38.6 per cent iron, 37.8 per cent silica, 6.5 per cent magnesia and 0.54 per cent alumina. XRD and microscopic examination showed that the main minerals in the ore were amphibole (42 per cent), magnetite (39 per cent), and quartz (14 per cent). Amphibole, (Mg, Ca, Fe),Si8O22.2(OH), containing 50.3 per cent SiO2, 35 per cent FeO and 11.5 per cent MgO is the main gangue mineral in the ore, and about 30 per cent of the total iron in the ore is contained in the amphibole. Heavy liquid separation tests showed that it is very difficult to separate iron from silica by gravity separation to obtain a high quality iron concentrate. Three grind sizes were initially tested, ie 45, 38 and 20 ¦m. It was found that grinding to 100 per cent -38 ¦m (P80 of 29 ¦m) appeared to be the best option for liberating the magnetite from gangue minerals. The iron recovery to the LIMS magnetic product for the 100 per cent -38 ¦m sample reached 73 per cent and the iron content was 65 per cent. Further test work suggested that the optimum grind size was a Psu of 25 ¦m.

Jan 1, 1999

By K. Oraee

A comprehensive, harmonic and sustainable development has always been a real concern of state policy makers. To reach such development, regional planning is an approach which is widely applied. This paper deals with policies adopted by a given country with rich mineral deposits, in order to accomplish a mining growth as well as economic development in relatively poor regions. In this regards, first, some worldwide experiences belonging to China, with large scale mining operations and Nigeria with a small scale mining industry, are studied. The mining industry in Iran is then considered as a case study. The study continues by categorizing and prioritizing Iranian regions based on their mining potential and the degree of development, using statistical analysis and Taxonomy and AHP techniques. Results obtained serve to provide recommendations as to where capital investments in the mining industry would produce highest returns. The approach used, together with the practical policies suggested in this paper, can be used to adapt appropriate strategies for mining development in a way that contributes to regional development and a more effective income distribution.

Jan 1, 2012

By T. Tafi

The Ute-Ulay project area is located approximately five miles west of Lake City, in Hinsdale County, Colorado. The Ute-Ulay Mine site is approximately one mile east of the project area. The elevation of the site is 9,200 feet and is adjacent to Henson Creek (Figure 1) [ ] The Ute-Ulay Mining complex is an inactive gold, silver, and zinc mining/milling operation, that operated from the 1880?s until the 1970?s, and sporadically into the late 1990?s. The mining complex comprises several levels of underground mines, a flotation mill, and an abandoned town site. Due to the narrow, steep sided canyon, milled tailings were pumped upstream one mile in a sluice box to a wider section of the canyon, and deposited into five tailings impoundments and one berm located between the impoundments. An estimated 9,000 cubic yards (yd3) of fine grained tailings were located in the impoundments adjacent to the creek. The Ute-Ulay project area consisted of the mill tailings impoundments located upstream from the historic mine.

Jan 1, 2011

By R J. Norris, D J. MacKenzie

Gold-bearing veins have formed at a wide range of depths throughout the uplift history of the Otago Schist. The earliest gold mineralisation occurred during the later stages of Mesozoic metamorphism. This mineralisation was characterised by diffuse wall rock alteration with greenschist facies metamorphic or retrograde metamorphic mineral assemblages, and gold occurs in this altered rock. Quartz veins formed in .steeply dipping extensional fractures associated with this mineralisation type strike north to northeast. The Macraes mine exploits this deposit type. The present northwest strike of the mineralised zone at Macraes is a result of post-mineralisation deformation of the schistosity-parallel mineralised shear zone which hosts northeast striking extensional veins. This combination of schistosity-parallel shear zone and steeply dipping northeast striking veins may exist elsewhere in Otago, and this deposit type is most prospective. Steeply dipping quartz veins formed during post-metamorphic un-roofing of the Otago Schist strike northwest to west and occur as clusters of near-parallel structures in east and central Otago. These veins consist mainly of massive quartz, although some prismatic quartz occurs also. Breccia fragments in veins are common and these are generally silicified, with some gold. Wall rock alteration is negligible, and vein margins are sharp. A set of middle Tertiary veins occurs in northwest Otago. Most of these also strike northwest and dip steeply, but some strike northeast. These veins contain abundant ankeritic carbonate as well as quartz. The carbonate pervades adjacent wall rock as veinlets, but gold mineralisation is confined to veins. Quartz is commonly prismatic and vuggy, and contains gold, which is commonly coarse grained especially in silicified breccia zones. Associated veins contain stibnite. This vein type formed close to the paleosurface (>2 km). Mineralised veins in Marlborough currently strike northwest, but these have been rotated from northeast strike during Alpine Fault displacement of Marlborough from Otago. Some of these veins were formed under late metamorphic conditions and are similar to the north to northeast striking veins in Otago. As in Otago, this type should be considered to be most prospective if they have associated schistosity-parallel shears.

Jan 1, 2000

By J. Gurland

A method of measuring the degree of contact between grains of 1 phase in multiphase alloys is derived. It is shown that the number and the areas of contacts between grains can be determined by metallographic analysis. Relations between the area of contact, the dihedral angle, and the mean free path of spherical grains are developed. It is often desirable to interpret the mechanical behavior of alloys in terms of structural features observed under the microscope. A quantitative description of microstructures of multi-phase alloys requires consideration of geometrical and topological factors such as the amount, size, and shape of grains and the continuity of the constituent phases. The number and dimensions of grains may be metallographically determined by applying the methods described by Smith and Guttman1 and by Fullman2 in their papers on the measurement of particle size and internal boundaries in opaque bodies. The present work intends to show that the same methods can be used to evaluate some of the parameters of phase continuity; namely, contiguity, number of contacts, and areas of contact of grains of 1 phase. Application of these concepts may be found in such problems as the calculation of electrical conductivity of 2-phase alloys, or the evaluation of the length of fracture path through grains of a brittle phase more or less dispersed in a matrix. I. DEFINITION The following definitions and derivations are based on 2-phase alloys, of which the units of the microstructure are grains. Contiguity is defined as the average fraction of surface area shared by 1 grain of a phase with all neighboring grains of the same phase. In a 2-phase alloy of constituents A and B, the contiguity of phase B is given by: where Cb is the contiguity of phase B aBß is the average area of contact between a grain of phase B and adjacent grains of phase B, aAB is the average area of contact between a grain of phase B and adjacent grains of phase A. The contiguity is a measure of the average degree of contact between grains of phase B in the 2-phase mixture. The ratio varies from 0 to 1 as the distribution of phase B changes from a completely dispersed to a fully agglomerated structure. Smith and Guttman1 have shown that the relative areas of 2 kinds of interfaces in a volume are directly proportional to the number of interfaces of each type intersected by a random line. The lines can be drawn on metallographically prepared surfaces as long as these are random sections through the sample. The contiguity ratio of phase B then becomes: Cb = 2NBB/NAB + 2N BB [2] where: NBB is the number of interfaces between grains of phase B intersected per unit length of random line. Nab is the number of interfaces between grains of phase B and grains of phase A intersected per unit length of random line. The factor 2 arises in Eq. [2] because each interface B-B is associated with 2 grains of B-phase, whereas the interface A-B involves only 1 grain of B-phase. The calculations of contiguity do not require any assumption as to volume fraction, particle size, or particle shape. Fullman2 gives an expression for the determination of the mean free path between particles. The mean free path PB between grains of phase A, i.e., through grains or agglomerates of phase B, may be found from the relationship: PB =2fB/NAB [3] where fB is the volume fraction of phase B. The calculation of the mean free path is independent of grain shape and grain size distribution. The calculation of the number of contacts and of contact area requires assumptions of grain shape, grain size, and contact shape. In the case of uni-

Jan 1, 1959

By T. R. Wildeman

"At the Big Five wetland, which was built to treat drainage from a metal mine, encouraging results have attributed to sulfate reduction. Cu and Zn were reduced to below detection limits of 0.50 mg/L, Fe was reduced by at least 90% to below 3 mg/L, and the pH was raised from below 3 to above 6. The study showed that treatment was primarily through microbial processes within the substrate and that plants were not needed to insure success.Constructed wetlands can be taken through design and proofing stages, and into operations scale in a meaningful time frame for on-line acid drainage remediation. In staged design, laboratory experiments are initiated to determine reasonable substrate materials for remediation of a particular drainage. When a reasonable substrate is found, bench scale experiments are initiated as the next stage in the design. In these studies, removal efficiency, permeability, and flow are analyzed to identify candidate substrate which will support sulfate reduction and be hydraulically reasonable. Using this design method at one site, an acid drainage of pH 2.5 was raised to a pH of above 7. Total heavy metal concentrations in this drainage exceeded 900 mg/L. In the pilot constructed wetland Cu, Zn, and Fe were reduced by 99%.Determining how well these anaerobic cells operate in the winter is done at the pilot plant site in Idaho Springs, CO. It's been found that over the last four winters, those cells that emphasize anaerobic removal within the substrate have operated continuously and effectively the year round. Winter operation is aided by the fact that the water temperature of the acid drainage is always between 14 and 16° C, and the cell can be readily insulated from the cold. Activity of the sulfate reducing bacteria may decrease during the winter. However, it appears that organic complexation of metals helps to maintain low concentrations of metals in the effluent."

Jan 1, 1992

By Willie M. NeSmith

Conventional augered, cast-in-place (ACIP) piles were introduced into the New York City area as a result of the damage to existing structures caused by pile driving operations. ACIP piles are often specified where deep foundations are to be installed adjacent to transit facilities, sensitive underground utilities or in close proximity to existing structures. However, loss-of-ground issues associated with the installation of ACIP piles have prevented the wide-scale use of these systems. Beginning in 2002, Berkel & Company Contractors, Inc. began using its augered, cast-in-place displacement (ACIPD) system in the New York City area. Like conventional ACIP piles, this system produces almost no vibration. Also, as almost no material is brought to the surface, there is no opportunity for loss of ground. This paper presents a description of Berkel's displacement pile system and a brief discussion of six projects in the New York City area that have been executed with this system over the past two years.

Jan 1, 2004

By F. Charette

The paper reviews recent investigations of the impact of corrosion on the performance of both plain and coated Swellex rock bolts. It addresses the problems associated with estimating and predicting corrosion rates of friction bolts, and based on field data it suggests an empirical relationship to predict corrosion rates. A review of the necessary qualities for a protective coating leads to recent experience with coated Swellex bolts that suggest that they can contribute to extending the useful life of Swellex bolts in potentially corrosive environments.

May 1, 2004

By K Ehrig

You are a geologist, geometallurgist, or metallurgist/process engineer and are fortunate enough to work for an organisation who asks you to design/execute a geometallurgy program. What seems like a simple request is actually not a trivial exercise. æRecipeÆ style manuals are not readily available. However, many æexpertsÆ are lurking around willing to deliver solutions which will solve all of your problems. Even though similar ore deposit styles (e.g. porphyry Cu, IOCG, Ni-laterites, calcrete hosted U, etc.) have many similar characteristics, each ore deposit is unique. Hence your geometallurgy program needs to be æfit-for-purposeÆ. This paper offers some insights gained via designing and executing geometallurgy programs from exploration through to production, and working at a mine where you are held accountable for your metallurgical performance predictors.CITATION:Ehrig, K, 2013. Geometallurgy - What do you really need to know from exploration through to production?, in Proceedings MetPlant 2013 , pp 28-33 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

By Alicia Esther Ares

The family of Zn-Al (ZA), Zn-Ag and Zn-Al-Ag (ZINAG) alloys offers high mechanical properties, ease of finishing, the advantage of low energy and pollution-free melting. Also, present alternatives to the well developed alloy systems, such as brasses, bronzes, cast irons and aluminum alloys. The main objective of this paper is to measure thermal parameters in ZA, Zn-Ag and ZINAG hypoeutectic and hypereutectic alloys directionally solidified which present columnar, equiaxed and columnar to equiaxed transition structures (CET). Also, estimate the mechanical properties, such as microhardness and tensile parameters and correlate these with the thermal (cooling rate) and structural parameters (grain size and dendritic spacing). The different types of structures were analyzed with optical and scanning electron microscopy. The results showed the influence of concentration, microstructural arrangement and thermal conditions during solidification on the mechanical properties. The results of the present investigation are compared with previous experiments.

Jan 1, 2010

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By Eric M. Hill, Daniel E. Walsh, Hsing K. Lin, John T. Hollow

The Fort Knox Mine is located in Alaska’s interior where the average ambient air temperatures range from -24°C in January to 16°C in July. The mill processes a free milling gold ore utilizing both a gravity recovery circuit and conventional cyanide leach/carbon-in-pulp circuits. Plant slurry temperature cycles seasonally and allows for a unique opportunity to measure the impact temperature has on gold leach kinetics, carbon adsorption efficiency and cyanide destruction reactions. Mathematical models have been developed to accurately predict actual mill performance. This paper describes the development of the models and presents data that allow for a better understanding of the impact of circuit operating temperature on process efficiencies.

Jan 1, 2005

By Camier R. J, Perry G. J

Extensive deposits of brown coal exist in the Gippsland Basin, primarily in the Latrobe Valley. The total quantities of economically winnable coal in this region of Victoria and in other smaller fields are large enough to adequately assure Victoria's future electricity needs and to also provide large quantities for alternative applications, including liquefaction. As a result of the recent conflict in the Middle East attention has again been focussed on the production of synthetic fuels from coal. There have been many investigations over the years into the production of oil from Victorian brown coal. The purpose of this paper is to summarise the scope, objectives and major findings of these studies, with the emphasis on the direct hydrogenation route for converting brown coal to oil. The principal alternative processes are carboniastion and hydrotreatment of the product tar, or gasification and Fischer Tropsch synthesis of liquids from the product gas. The attractions of Victorian brown coal which have encouraged these studies include: ò the vast reserves of Victorian brown coal and the favourable conditions for low cost mining, ò the high quality of the coal (low ash, sulphur and nitrogen contents), ò the high reactivity of the coal giving high yields of product in hydrogenation to liquid fuels, ò the extensive data base available on the resource and its characteristics, and ò the availability of a skilled workforce and extensive infrastructure in the Latrobe Region to support a major resource development project. These advantages have been partially offset by: ò the high moisture content of the brown coal and the cost of drying, and ò the priority previously given to electricity generation in the allocation of the brown coal resource.

Jan 1, 1992

By Rafael C. Castro, Geoffrey Hughes, Fredrick (Rick) Vincent, Philip H. Albert

Seven pairs of drop and ventilation shafts, between two and nine feet in diameter, will convey combined sewer flow to a 230-foot-deep, 26-foot diameter storage tunnel. This paper will present case histories for each site. Discussion will include functional requirements, program and site access constraints, structural design, geology, the variety of excavation and lining construction methods used, and lessons learned. Noteworthy observations include the importance of assuring competent ground sup-port at the soil-bedrock interface and of achieving tight verticality tolerance using both top-down and raise bore excavation methods.

Jan 1, 2007

By T. R. Curr, R. T. Jones

Keywords: Pyrometallurgy, Mintek, DC arc furnace, plasma, smelting, chromite, ilmenite, cobalt, slag, zinc fuming, dust, magnesium, laterite, ferronickel, arc modelling, Pyrosim, thermodynamics The Pyrometallurgy discipline at Mintek was initiated in the early 1970s, to support a growing ferroalloy industry in South Africa. In addition to a range of pyrometallurgical options, Mintek specialises in DC arc furnace technology and has pilot plant facilities up to 5.6 MVA, as well as a strong base in process and arc modelling. Industrial processes have been developed for ferrochromium production, ilmenite smelting, and cobalt recovery from slag. Recent work has been done on such processes as the production of ferronickel from laterite ores, the fuming and condensation of magnesium, and the recovery of platinum group metals from 'difficult' feedstocks.

Jan 1, 2006

By F. Burat

Large reserves of feldspar ore exist in the Aegean region of Turkey. The main colored impurities in these ores are iron- and titanium-bearing minerals such as anatase, rutile, sphene and ilmenite. In this study, a potassium feldspar ore containing mainly quartz and coloring impurities was subjected to beneficiation tests involving magnetic separation and flotation, which were applied either separately or in combination. Bench-scale flotation experiments using cationic collectors G-TAP and Flotigam V-4343 and using HF and H2SO4 as modifiers were employed to separate feldspar from quartz and to remove part of the titanium impurities. The best results were achieved with a combination of high-intensity wet magnetic separation and flotation. A feldspar concentrate containing 16.28% Al2O3, 10.75% K2O, 2.84% Na2O, 69.97% SiO2 and 0.16% Fe2O3 was produced. A quartz concentrate containing 2.30% Al2O3, 0.48% K2O, 0.42% Na2O, 0.07% Fe2O3 and 96.20% SiO2 was also obtained

Jan 1, 2007