Search Documents

By L. J. Terrill

Lateral displacement in the immediate roof beam at the Waste Isolation Pilot Plant (WIPP) is a significant factor in assessment of excavation performance for the design of ground control systems. Information on roof beam lateral displacement, expansion, fracture formation, as well as excavation convergence, is gathered using a variety of manually and remotely read instruments. Visual observations are also used when possible. This paper describes the methods used to measure lateral displacement, or offset, at the WIPP. Offset magnitudes are determined by the degree of occlusion in drillholes that intersect the offset plane. The Borehole Lateral Displacement Sensor (BLDS) was developed for installation at WIPP to monitor offset at a high degree of accuracy at a short reading frequency. Offset measurements have historically been obtained by visual estimation of borehole occlusion. Use of the BLDS will enable relationships between time dependent roof beam lateral displacement and expansion to be established in much shorter periods than is possible using visual observations. The instrument will also allow remote monitoring of roof beam displacement in areas where visual estimations are not possible. Continued monitoring of roof beam displacement, convergence, and expansion, is integral to timely and pertinent assessments of WIPP excavation performance.

Jan 1, 1996

The upper amphibolite-grade mctasediments of thc rinaroo area, North Queensland, form part of a regional aurcole to the large Tinaroo Batholith and are the stratigraphic equivalents of the Hodgkinson Formation of gencrally low metamorphic grade. There is no evidence of any lithological unconformity.The higher grade metasediments have a more complex deformation history than is typical for thc surrounding region and this may bc due to one or a combination of two factors; an additional strain componcnt associated wilh the intrusion of Ihe Tinaroo Batholith, or a more marked finite strain response to the overall regional stress field within hotter. more ductile rocks.Four deformational events can be characterized within Ihc Tinaroo Area. Close to Ihe Tinaroo Batholith D1 and D2, arc so strongly developed that they disrupl the continuily of Ihe original Iithological layering. In the aureole region, D1 is strongly overprinted and its original fabric intensity is obscured, but both D2 and D3 display a mappable decrease in intensity away from the granite margin. These three deformations occurred during Carboniferous or early Permian time. D4 is later and only patchily developed.The broad, moderate pressure metamorphic aureole surrounding the Tinaroo Batholith is a typical of the CairnsCooktown group of Permo-Carboniferous granitoids. which usually develop narrow, lower pressure contact aureoles. Two periods of metamorphism are distinguishable. The first reached peak temperatures somewhat greater than 520°C, the second temperatures around 620-630° C immediately adjacent to the granite contact.Several cale-silicate lenses containing scattered scheelite mineralization occur within the area. Scheelite appears to have crystallized at the same time as the cale-silicate minerals, its appearance coinciding with the intrusion of the Tinaroo Batholith. Unlike many "skarn-type" scheelite deposits, the scheelite-bearing cale-silicates are Fe-poor, with no positive correlation between total Fe and W.

Jan 1, 1982

Delivered at the University of Sydney, on June 4th, 1954.THE TORCH WE HOLDLast year Our Institute celebrated its Diamond Jubilee, coincident with the holding of the Fifth Empire Mining and Metallurigcal Congress in Australia and New Zealand. We can be proud of our growth over the 61 years since the inaugural meeting in Adelaide in April, 1893, which followed suggestions from a provisional committee of mining men, formed in 1892 in Broken Hill.We can also be proud of our technical achievements in the fields of economic geology, mining and metallurgy.Should we be content with the growth of our mining and metallurgical industries over these years? My answer is in the negative. The discovery of new mineral deposits is essential for the continuance and development of the industries we represent.Let me review the background and trends of our industry in an attempt to emphasise the changing factors influencing the search for minerals and their exploitation.Australia was blessed with the discovery of coal in New South Wales in 1796; copper in South Australia at Kapunda, Burra, Wallaroo and Moonta in the eighteen-forties; gold in Victoria and Eastern Australia in the 'fifties; tin at Mount Bischoff, Tasmania, and gold at Charters Towers, Queensland, in the 'seventies; lead-silver at Broken Hill, New South Wales; gold and copper at Mount Morgan, Queensland, and copper at Mount Lyell, Tasmania, in the 'eighties; and gold at Kalgoorlie, Western Australia, and zinc-lead atRosebery, Tasmania, in the 'nineties. As well, the iron ore deposits of the Middleback Ranges, South Australia, and Yampi Sound, Western Australia, were known before...

Jan 1, 1954

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By Madgwick J. C

Leaching column techniques and microbiological methods have been described in detail in Madgwick and Ralph (1980) and Madgwick, Ralph and Sadler (1981).Sixty-nine kilograms of copper porphyry ore (0.4 per cent Cu, 2.7 per cent Fe) (particle size 2.4-11.2 mm; 60 The effect of sodium chloride (O.6M) irrigation on bacterial leaching of Bougainville copper porphyry ore was studied.Viability of suspended Thiobacillus ferrooxidants was reduced to less than 10 cells/ml in NaCI (O.6M) compared with 10' eells/ml in dilute II,SO, (0.01 M, pll 2). Salt irrigation had no significant effect on heterotrophic and sulphur oxidizing bacteria. Increascd short term recovery of copper (145 g/tonne/ 15 days) was followed by a marked decrease in tenors to less than 20 mg/litre/day compared with an acid leach, steady release, of 110 mg/litre/day. Resumption of acid leaching restored average solution copper to 46 mg/litre/day and the viability of suspended T Ierrooxidates to 10 cells/ml.Quantitative removal of sodium ehloride from ore particles was difficult and t races of NaCI remained for more than 200 days.

Jan 1, 1982

By McKenzie P

The techniques of geological control developed by the Coal Geology Sections of the Broken Hill Proprietary Company Limited and Australian Iron and Steel Proprietary Limited in providing geological service in the coilieries operated by these associated companies cover the provision of geological control for both planning and production in each of which the significance of geology has in the past been only poorly appreciated by the coal mining industry.While the adoption of similar techniques is well within the capacity of major companies there is considerable scope for the development of government geological services providing specialized assistance of this nature for smaller scale producers.INTRODUCTIONThe coal mining industry in Australia can instance many notable mistakes caused by failure to obtain sufficient geological information or by incorrect interpretation of available geological evidence both before the commencement of mining and during the progress of operations. Substantial development undertaken in, areas with insufficient or inferior coal reserves, difficult mining conditions caused by failure to adjust operations to geological circumstances, and the irregular development of mine workings caused by unexpected geological features, all bear witness to the lack of geological foresight by the industry.Along with the more widespread general use of applied geology, an increasing acceptance has developed during the past ten years of the valuable contribution which can be made by this science to the exploitation of coalfields. In spite of the advances which have been made, there is still a wide scope for further detailed application of geology throughout the coal mining industry in Australia.

Jan 1, 1963

By Kentaro Kuraji

INTRODUCTION Background Tokyo, the capital of Japan, is one of the largest cities of the world. As many as 33 million people live in Tokyo and three neighboring prefectures although the city occupies only 0.6% of the area of the country. The network of Metropolitan Expressways serves as a major artery for daily physical distribution in Tokyo. The Central Circular Route of the Metropolitan Expressway (MECCR) is located innermost among the three circular routes in Tokyo (Figure 1). Once completed, MECCR is expected to drastically mitigate traffic congestion in the central Tokyo area and provide drivers wider varieties of options in route selection. Alleviating congestion is estimated to reduce 400,000 tons of carbon dioxide emissions annually. The eastern and northern sections and part of the western section of MECCR have been completed with the total length reaching 33 km. The western section will be extended southward by approximately 4 km in the spring of 2010. An 11-km-long western section of MECCR that is currently being constructed is composed mostly of tunnels. A large number of power supply, gas supply, telephone, drinking water and sewerage pipes have been placed under the Yamatedori avenue along which MECCR is being constructed. The shield tunneling method has therefore been adopted for constructing tunnels along the route. The method involves the advancement of a shield tunnel boring machine (TBM) through the ground simultaneously assembling segmental rings within the shield. The method not only enables the building of highway tunnels more quickly and efficiently than other methods but also minimizes the effects of construction work on the surrounding area and the environment. Constructing the tunnel using the conventional cut-and-cover method might have required large amounts of time and cost because relocating the numerous objects buried under the Yamatedori avenue might have been necessary during tunnel construction. It was also considered desirable to place the tunnel at a depth of 30 m or more from surface to prevent tunnel construction from adversely affecting railways because the tunnel was expected to cross eleven railways and subways. This is one of the reasons for selecting shield tunneling as an effective method. The shield tunneling method was finally adopted for a length of 7 km in the 11-km western section of MECCR. The shield tunneling method was also employed in the Ohashi Tunnel located southernmost in the 11-km western section of MECCR. This paper describes the construction of the Ohashi Shield Tunnel.

By J. A. McLennan, J. M. Ortiz

Nickel laterite deposits are typically formed from tropically weathered mafic-to-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs) or representative dozer regions (RDRs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate “optimum” RDR mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each RDR. The optimum mining elevation is the elevation where the lowest summed cost of “accepting dilution” and “wasting ore” occurs. The reported RDR dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation. The reported RDR lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum RDR mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Jan 1, 2006

Results of flotation tests on lead-zinc ore from Broken Hill, N.S.W., confirmed that flotation at pH 9 in the presence of cement gave poorer metallurgical results than flotation at pH 7. Additions of 2 kg/tonne wood raspings [e.g. blackbutt (Eucalyptus pilularis), blue gum (E. saligna), brushbox (Tristania conferta), or turpentine gum (Syncarpia laurifolia)l had little effect at pH 7 but greatly accentuated the deleterious effect of cement at pH 9. This was shown to be caused by e:xtractives (e.g. polyphenols and carbohydrate materials) derived from woods at pH 9. The proportion of extractives, as shown by DV absorbance spectra, increased with increase of pH and was affected by various salts.Additions of 1 kg/tonne Al2(S04)3.16H20 when cement or cement and wood were present showed that metallurgical results obtained by flotation were then very simHar to those in the absence of cement or wood or both. This was ascribed to lower pH values in the presence of aluminium sulphate and possibly to specific chemical effects.Additions of aluminium sulphate appear to offer an economic solution to the problem of treatment of ores contaminated with cemented fill at Broken Hill.

Jan 1, 1974

The purpose of this paper is to outline some aspects of the experimental worlr that has been carried out in the mineral dressing laboratory at M'ount. Morgan during recent years.The subject matter has been dealt with under the following headings:1. Comminution of various mill products.2. The application of sulphur dioxide as a flotation reagent.3. Heavy-media separation.4. Bulk flotation of sulphide ores.COMMINUTION OF VARIOUS MILL PRODUCTSThe following data were cbtained by processing fractions of reserve grade ore.Granular TailingIn Table 1 are shown the results of tests on material representative of average grade tailing. In the first test (H1 ) the granular tailing was floated as received and in the second test (Ha) the tailing was ground prior to flotation.

Jan 1, 1952

By Sara Jane Boles

In recent years the demand for products of greater refractoriness has placed an ever-increasing emphasis on ceramic materials, including the metallic oxides. Magnesia (MgO) is one of the most important of these oxides, exhibiting, as it does, high electrical resistivity, high slag resistance, and a melting point of 2,800° C. However, magnesia has a tendency to hydrate in the presence of water and to volatilize above 1,500° C. in certain kiln atmospheres and has a comparatively low resistance to thermal shock. Because of these disadvantages, the previously listed advantages inherent in this material have been largely overlooked, and research on magnesia has lagged behind that on oxides such as alumina and zirconia. This bibliography has been prepared in an effort to present to Government and industry a comprehensive picture of the prospects for greater utilization of magnesia as a refractory material in future research. To provide as selective and accurate a collection as possible, the references included cover magnesia in a pure state, not as an additive or in combination with other materials. However, several references discuss the effect of minor impurities (less than 5 percent of the total) on the properties of magnesia, as these papers are considered to be of special importance. A few references to articles on forming techniques are also included, as they are valuable additions to the overall treatment of the subject. The processes used in obtaining and refining the raw materials are adequately covered in earlier publications and are excluded. A number of references are omitted as being of questionable value in enhancing the cumulative study of pure magnesia as an ultra-high-temperature refractory material.

Jan 1, 1962

By Morabito J, Harrop D. W

Uranium exploration was commenced in 1973 and carried out at a regional scale over a wide area of the northern part of the Camarvon Basin of Western Australia by Minatome Australia Pty Limited and their joint-venture partners. As a result, pervasive uranium mineralization has been found in the Cretaceous sandstones near Manyingee Hills in the Onslow Region, which were probably deposited in a near-shore, fluvia deltaic palaeo-environment.Mineralization is generally found in poorly sorted argillaceous sandstones and siltstones near redox fronts formed by oxidizing waters circulating in reduced sediments. The principal minerals found in the two Manyingee deposits delineated so far are coffinite, uraninite with associated pyrite in the reduced zones, and phosphuranylite, siderite and limonite in the oxidized zones. The presence of dissolved uranium in the superficial aquifers, of secondary uranium minerals as coatings on granitic rocks, and of recent uranium-bearing calcrete sediments, suggest that the whole Cretaceous-Precambrian system has been subjected to the formation ofroll-front type uranium deposits since the Cretaceous. Continuing exploration is locating additional uranium occurrences. The deposits outlined so far are being evaluated for their amenability to in situ leaching tests planned for 1982-1983.

Jan 1, 1981

By Sharpe E. J

The Triton lode is a schistose feldspar biotite chlorite rock with quartz, carbonate, pyrite and some pyrrhotite. Its more chloritic sections strongly resemble the enclosing greenstones, its more feldspathic portions are indistinguishable from the flne-grained phases of the porphyry dyke into which the southern extremity of the ore body merges. The ore body' has a length of 880 ft. and an average width of I2t ft.; in places this widens to as much as 30 ft.The average dip is 85° west and pitch of the ore shoot 75° south.METHOD OF SAMPLING.With the exception of a limited amount of channel sampling (a reference to which is made elsewhere in this paper) all the sampling is by chip sample.The samplers use a hammer weighing approximately 11 lb. and chip directly into the sample bags. Sampling is generally carried out over 3-ft. sections and portions thereof to the nearest half foot-thus a face 8t ft. wide is divided up into two sections of 3 ft. each and one section of 2 ft.-no measurements of less than 4 ft. are used and calculations are all in feet and dwt. per long ton.In the oxidised stopes wp.ere the lode is much narrower, .i.e., 6 ft., sampling is over 2-ft. sections. All borehole samples are over 2-ft. sections, this corresponding approximately to steel changes.(a) DEVELOPMENT SAMPLING.Driving.-This is done by following the east wall and each face is sampled-this corresponding to an advance of 5 ft. If the full width o,f the lode is not exposed boreholes...

Jan 1, 1938

By Lyne Côté, Jose Adante

"The Caribou underground mine, 50 km west of Bathurst, the Restigouche open-pit mine, another 30 km west and the concentrator located at the Caribou mine site resumed operations in July 2007 after a nine year shutdown. The Caribou operations achieved commercial production on Jan 1. By June, 2008, all metallurgical targets had been achieved or surpassed with the production of lead and zinc concentrates assaying approximately 50% Zn and 45% Pb respectively with recoveries exceeding 80% for Zn and 70% for Pb.The deposit features very fine-grained massive sulphide mineralization, which in the past has proven difficult to process. ISA Mill Ultra Fine Grinding Technology in combination with conventional flotation technology is used to process these complex oresSeveral modifications arising from experience gained from past operations, an extensive research project at Lakefield Research and post startup flow sheet and reagent alterations have been employed to achieve this break through performanceThis paper describes the design, start up and optimization of the Caribou operations including the many challenges faced including the flotation of mineral particles with K80s ranging from 35µm to 8µm.HISTORICAL BACKGROUNDThe Caribou massive sulphide deposit was discovered by Anaconda geologist Cam Cheriton in 1959. Anaconda initiated an extensive underground exploration and discovered a super gene copper blanket which was developed into a small open-pit mine-mill operation that ran from 1970 until the depletion of the copper ore in 1974. East West Minerals, an Australian public company, purchased the mine in 1986 and operated for only seven months producing a single bulk lead-zinc concentrate. In 1995, Breakwater acquired the Restigouche Open pit and Caribou underground deposits. Breakwater began milling operations in July 1997 but Caribou Mine failed to commercialize production, and the company decided to shut it down in August 1998, because of declining metal prices. The mill was plagued by mechanical and design problems, but deficiencies in metal recoveries prevented the operation from reaching desired levels."

Jan 1, 2009

If the industry keeps doing what it has always done, it will continue to get what it has always got - rising operating costs. Why is this so? Generally grades being chased are becoming lower, stripping ratios becoming higher, ability to attract personnel to the industry becoming harder and/or more expensive, higher safety standards are being demanded and environmental governance is being enforced.   How then should the surface mining industry plan for the future whilst delivering on improved safety and the environment? In-pit crushing and conveying (IPCC) points the way, as a partial or complete substitute for trucks.   IPCC systems promise significant advantages over traditional truck and shovel operations, including improved safety, reduced operating costs, reduced dust and noise emissions, far greater efficiency in energy use (electric versus diesel motors predominantly and the ability to regenerate electricity back into the local grid for downhill situations), reduced carbon emissions (dependent on power generation source) and reduced water consumption. Despite these advantages, there is a general industry reluctance to migrate from truck and shovel operations. This reluctance stems from a familiarity with truck and shovel operations and a perceived concern that IPCC lacks flexibility which will negatively impact on the mining operation.   In studies conducted since 2007 (with the new modular builds) comparing IPCC with truck-optimised pit designs, IPCC has delivered up to USD$0.82 per tonne moved less than an equivalent truck operation. In addition, IPCC is easily automated from a central control room (local or remote) - something that trucks have yet to commercially achieve.   IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations - its safety, the impact on the environment and its costs. It maybe of interest to note that there is over 200 IPCC installations worldwide today.   This paper and presentation will assist in furthering the understanding of IPCC and its applicability.

Jun 1, 2010

By J. M. McKinley

Mineral exploration programmes around the world use data from remote sensing, geophysics, and direct sampling. On a regional scale, the combination of airborne geophysics and ground-based geochemical sampling can aid geological mapping and mineral exploration. Since airborne geophysical and traditional soil-sampling data are generated at different spatial resolutions, they are not immediately comparable due to their different sampling density. Several geostatistical techniques, including indicator cokriging and collocated cokriging, can be used to integrate different types of data into a geostatistical model. However, with increasing numbers of variables the inference of the crosscovariance model required for cokriging can be demanding in terms of effort and computational time. In this paper a Gaussian-based Bayesian updating approach is applied to integrate airborne radiometric data and ground-sampled geochemical soil data to maximize information generated from the soil survey, enabling more accurate geological interpretation for the exploration and development of natural resources. The Bayesian updating technique decomposes the collocated estimate into two models: prior and likelihood models. The prior model is built from primary information and the likelihood model is built from secondary information. The prior model is then updated with the likelihood model to build the final model. The approach allows multiple secondary variables to be simultaneously integrated into the mapping of the primary variable. The Bayesian updating approach is demonstrated using a case study from Northern Ireland. The geostatistical technique was used to improve the resolution of soil geochemistry, at a density of one sample per 2 km2, by integrating more closely measured airborne geophysical data from the GSNI Tellus Survey, measured over a footprint of 65 x 200 m. The directly measured geochemistry data were considered as primary data and the airborne radiometric data were used as secondary data. The approach produced more detailed updated maps and in particular enhanced information on the mapped distributions of zinc, copper, and lead. The enhanced delineation of an elongated northwest/southeast trending zone in the updated maps strengthened the potential for discovering stratabound base metal deposits..

Jan 1, 2014

By M. du Plessis

This paper describes the evaluation of a limit equilibrium model to simulate the behaviour of crush pillars in platinum mines. An analytical model was derived to calculate the residual average pillar stress (APS) values of the crush pillars. The values predicted by this model were compared to the numerical values obtained from TEXAN simulations. In general, the limit equilibrium model appears to be very attractive for simulating pillar failure as the gradual crushing of the outside of the pillar and the transfer of stress to the intact core can be replicated. The value of the TEXAN crush pillar model was further demonstrated by simulating an idealized layout with crush pillars between two adjacent panels. The simulations illustrated that oversized pillars will not crush close to the face and this may lead to seismic failure in the back area. An important finding of the study is that closure measurements may prove to be a very valuable diagnostic measure in crush pillars layouts. Distinct differences in magnitudes of closure were simulated for a scenario where the pillars crush as expected, compared to the scenario where an oversized pillar is left. Experimental closure data collected in a crush pillar stope provided further evidence regarding the value of closure measurements in these layouts.

Jan 1, 2011

By Frank J. Arland

Augered-Cast-in-Place piles have been used successfully for many deep foundation applications. The four case studies discussed herein describe ACIP pile projects where problems developed during ACIP pile installation requiring changes to the method or sequence of installation. The case studies illustrate the importance of understanding existing subsurface conditions and project constraints when considering the use of this pile type. Ground loosening and over-excavation of soil during the augering process, a significant concern for fine to medium sands and non-plastic silts below the water table, can significantly impact adjacent structures. This risk needs to be evaluated during the pile selection process and generally can be mitigated, but not eliminated, by requiring the use of piling equipment with high torque and slow auger rotation speed to advance the auger with minimum amount of rotation. In some applications where high lateral stresses in the soil are present such as at the base of retaining structures, the use of ACIP piles may not be appropriate if structure movement is unacceptable. On the other hand, ACIP piles have been successfully used to support deep foundations in preconsolidated varved deposits where the new structure was designed to accommodate recompression settlement.

Jan 1, 2004

By N. A. Eilertsen

Procedures of mining high-calcium limestone underground at the Kimballton mine of the Standard Lime and Cement Co. in Giles County, west-central Virginia, are described. Drilling and blasting procedures arc discussed in detail, and direct mining costs are tabulated in percentage of total cost. Output, about 1,725 tons of limestone a day, is attained with heavy trackless equipment by the room and pillar method of ruining; modified by benching floors. Operating features include underground air compression, electric-eye control of curtained doorways, use of a single jumbo drill rig for all drilling, and an effective plan for maintenance of equipment. The company's safety program has contributed to an outstanding safe mining record. The mina is integrated with a plant on the property which converts the stone to metallurgical and chemical grade lime.

Jan 1, 1964

By Tim O’Neil

Question: Looking forward, do we face a future in which energy markets, energy policy and energy conflicts threaten to preoccupy, if not dominate, our concerns over economic growth, national security and domestic tranquility? The answer is, we may indeed face such a future. Question: What oil resource is comparable in size to the reserves of Saudi Arabia and presents a tremendous opportunity? The answer, the oil sands in Alberta, Canada. Question: What is the largest mineral staking rush in North American history, still under way? It has so far led to the development of two large mines. The answer is the Point Lake diamond strike in Canada’s Northwest Territories. It led to the development of the Ekati and Diavik mines.

Jan 1, 2004