Search Documents

By L. A. Stewart

This paper describes all occurrences of barite in Arizona that were known or reported to the authors. The history, ownership, production, and geologic setting are discussed for most of the deposits. The uses and specifications of product grades are briefly discussed. Seventy-five deposits were examined in 9 of the 14 counties of the State. The descriptions are given under county headings. No occurrences were reported in the four northeastern counties of Coconino, Navajo, Apache, and Greenlee, nor in Santa Cruz in the southern part of the State. From about half of the deposits examined, 55 samples were taken; of these, 45 were for chemical analysis, and 8 larger samples, ranging from 100 to 350 pounds, for beneficiation tests. A 30-ton bulk sample was taken for pilot-plant tests. Bench-scale flotation tests of the eight samples employing several different procedures and reagent combinations yielded marketable-grade barite products with barite recoveries ranging from 60 to 97 percent. Five of the samples contained enough fluorspar to warrant its recovery. Acid-grade concentrates, which accounted for fluorspar recoveries of 45 to 70 percent, were obtained from three of these ores. Batch laboratory tests of a representative portion of the 30-ton bulk sample revealed that acid-grade fluorspar and high-grade barite concentrates could be recovered. Results of the laboratory and continuous pilot-plant tests of this ore will be presented in a separate report.

Jan 1, 1960

During the course of the major research in the Metallurgy Department of the University of Melbourne into the creep characteristics of lead and .its dilute alloys, it has been the practice to prepare the majority of test specimens from rolled strip. From time to time during the progress of the work, certain variables involved in. the rolling of the experimental ingots have been investigated. It is proposed to collect together in this paper the results of these experiments. Some general features relating to the type of deformation produced have been discussed in a previous paper.While it is admitted that the conditions prevailing through this work differ' in some respects from those of industrial rolling practice, it is felt that many of the factors investigated have an important practical significance. Some of the work described forms a continuation of the researches of R. S. Russell (2) , (3) , (4), into the recrystallization of various pure leads after deformation by rolling.MATERIALS USEDIn this work, a variety of "pure" leads and certain dilute alloys made from the purest of the basis leads have been studied. The compositions of the basis leads and the corres...

Jan 1, 1940

THE slide-rule, as a quick and convenient instrument for performing approximate calculations, is steadily growing more and more into favour with the engineer, and results obtained by it are considered close enough to enable him to satisfactorily dealwith a considerable portion of his work. To the surveyor, however, whose ordinary computations must be as precise as his measurements, the present makes of rule are insufficient, except for a very narrow margin of the scales and for rough work. Few will carry the rule when they can clearly see that it is unreliable for general routine, and the careful surveyor is inclined to look askance at those who do use it, recognizing the temptation there undtmbtedly must be to push it into work that the log book should be called upon to treat. From the fact that a surveyor's duties take him on the surface in all weathers, and underground in many wet and uncomfortable places, where the manipulation of a book of mathematical tables becomes both awkward and patience-trying, an efficient slide-rule must offer the mbst transparent advantages. Again, a surveyor being specially trained to read divided scales quickly and accurately, the slide-rule must commend itself as an apt addition to his outfit.

Jan 1, 1912

By Jack Eloranta

The winning of metals often requires fine grinding of very hard ore. The US Bureau of mines measured compressive strengths exceeding 100,000 PSI (700 MPa) in Minnesota taconites. Grinding down to 300 mesh (50 µ) is required for some fine-grained taconites. While other metal ores may not be as strong, significant grinding costs are the rule rather than the exception. One author recently reported that a 7% drop in grinding costs would fully offset a doubling of the drill and blast budget. Another author found that drill and blast costs were 13% of the costs of producing iron ore concentrate while fine crushing and grinding were over 60% of the cost of producing concentrate.

Jan 1, 2013

By Baxter J. L

Post-tertiary training programmes have been designed and produced for geologists at different levels of understanding and expertise in the relationship between gold mineralization and shear zones. A workshop format was used as it allowed both clients and facilitators to participate in the learning process. Evaluation by facilitators and participants refined the workshop programme as an effective skills oriented learning process. The general observation is that post-tertiary training in small, interactive, practical, learning oriented groups is far better than lecture oriented short courses for developing skills based learning. The evaluation indicates that the process in post-tertiary training must include aspects which are both useful and used.

Jan 1, 1989

I have chosen this subject in view of the fact that, while there are many and ample opportuuities of getting reliable assays made, there are but few who are in a position to obtain reliable data on the sampling of minerals and metals my long experience at Port Pirie, where, for five years, I had charge of the Refining and Sampling Mill, showed me how important it was that a correct sample should be taken.Weighing; This, to the ordinary layman, seems so simple that no expert knowledge is needed, but in actual practice there are hundreds of pounds to be lost by the lack of knowledge in this department.(1.) There is the matter of weighing in large or small quantities.(2.) The class of weighing machine used.(3.) The accuracy of weights used.We all know that, say, 1000 tons of ore cannot be weighed in one parcel; but the fewer the weighings the less loss to the seller (and usually wishes it weighed in small lots carefully) for it is a well known fact that the most sensitive scales take a certain weight to show distinctly the indication of the balance, or, in other words, what is known as "the pull of the scales." As for instance, 1000 tons weighed in lots of 1 c. each, taking the pull of the scale as being equal to 1 lb., would give a result of 9 tons loss to tbe seller, and as most of the ore sent to Customs works is worth 5. -£20 per ton-this would mean £180 loss to the careful man.

Jan 1, 1901

By Pullen G, Rose M

Continuing Professional Development (CPD) is not just a catch-cry. It is an essential component of every-day life in many professions, including accountancy, law and public administration. Without realising it, many other professions are undertaking CPD activities in an un-structured way, including mining, metallurgy and geology. Examples include Annual and technical conferences of The Institute, Branch-level technical meetings and in-company training and development programmes and technical exchanges. Whilst approaches to date have undoubtedly helped keep the Australian mining industry at the forefront of mining technology, one cannot presume that technological development will stand still. To meet this challenge, human resource development must keep pace, not only to optimize utilization of technological developments, but more importantly to develop firm bases from which new products, processes and technologies can be developed within Australia.

Jan 1, 1989

By J Elsen, R Snellings, K Van Balen

This research concerns the mineralogical study of the physico-chemical reactions taking place at the pozzolan-binder interface. Lime binder/ pozzolan mixtures have been prepared for different natural zeolites. Analcime, phillipsite, chabazite, erionite, mordenite and clinoptilolite were mixed with portlandite and water, after which the progress in the reaction was quantitatively determined by thermogravimetrical analyses from three to 180 days. A first and important step was the thorough characterisation of the raw materials by quantitative X-ray diffraction (XRD), X-ray fluorescence (XRF), scanning electron microscope energy- dispersive X-ray (SEM-EDX) measurements of the zeolite minerals, Brunauer-Emmet-Teller (BET) specific surface area measurements, grain-size analyses and cation exchange capacity measurements. Beside these zeolite samples with varying Si/Al ratios, two clinoptilolite samples exchanged to the calcium, potassium and sodium form were studied and the difference in their short- and long-term reactivity was assessed. Also the difference in reactivity between identical clinoptilolite samples ground to different grain sizes, obviously having different specific surface areas, was determined experimentally. The results indicate that the external surface area only influences the short-term reactivity, whereas the cation content has effect on both long- and short-term. Na-exchanged samples combine clearly more portlandite in the first few days, whereas the reaction slows down afterwards compared to K- and Ca-exchanged samples. The early reactivity of the unexchanged zeolite samples could be explained by these two parameters, but their long-term reactivity seemed to be related to their Si/Al ratio. Samples with zeolites rich in Si reacted faster then their Al-rich counterparts.

Jan 1, 2008

The fundamental features of the Cable Belt Conveyor are described. It consists of independent wire ropes which take the transmission load, and a special reinforced rubber belt which acts 'only as carrier of material. The first cable belt installation in Scotland is described briefly.A general description of this type of conveyor is followed by details of the rubber belt construction and the method of joining sections of belt. The drive unit, the tensioning arrangements and the power requirements are outlined.Applications of the cable belt conveyor are 'dealt with and its advantages summarized.INTRODUCTIONThe cable belt conveyor, as its name implies is a conveyor composed of steel wire ropes and a rubber belt, in which the ropes serve as transmission members, and the belt merely as a carrier of materials.Over the years it has been the ambition of engineers connected with the belt conveyor industry to develop a conveyor that would use the high tensile strength of wire ropes to transmit the stresses involved in the driving of large capacity belt conveyors. Different lines of approach have been adopted in the United States of America and in Britain. In the United States the method adopted was to introduce a large number of flexible steel cables into the rubber belt itself, in the form of a closely packed layer arranged across the full width of the belt. These small cables are packed in a nylon filled duck envelope which is incorporated in the rubber belt. This is commonly known as the steel corded conveyor belt. In Britain, a Scottish firm developed a rubber belt conveyor in which full advantage was taken of the high tensile features of wire rope, without embodying or moulding the wire rope into the rubber belt, so that the two wire ropes and the rubber...

Jan 1, 1957

The importance of timbering, not only from a financial point of view but from an actual mining point of view, is so often overlooked or slightly glossed over by the average expert and investor, that I have thought it would prove interesting to go into the matter and to invite discussion upon the subject. We will first take small veins, or reefs as they are termed in some mining countries; and by small veins it is intended to denote fissures from a few inches to three feet. The ore body is supposed to be confined within well defined walls free from gangue matter, unless the casing can be defined as such. Now, if the walls are smooth and moderately hard, no timbering is required other than the stulls, which are braced from wall to wall in order to form platforms or stages to stope from. Should the reef from wall to wall prove payable, or should the vein be of a character to prohibit cleaning or sorting; and it be determined to send the whole of the stone to the, reduction works, the stuUs should be left in place until the section or block of ground is worked out, in order that if a weak spot in the walls (especially the hanging) occur, it would be possible, without any particularly extra expense or difficulty often times accompanied by danger to brace and secure the slabs. After the block became entirely stoped, it would pay where labour was cheap to remove the majority of timbers to stull another section.

Jan 1, 1901

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

In preparing this paper, the writer hopes to achieve two main objects. Firstly, an indication of the desirable features of coke from the viewpoint of a blast furnace operator should be of assistance and value to those connected with coal and coke research, coal mining, the manufacture of coke and the production of iron. Secondly, it is hoped that the conclusions and opinions expressed herein, which are known to be of a controversial nature, will promote some discussion and thought. In this way, other workers may see fit to contribute and enlarge our general knowledge of Australian coke and its behaviour in blast furnaces.Those properties of coke that are considered to be of importance to blast furnace operation will be examined. Although broadly speaking, the composition and characteristics of coke are inherent in the coals used, any special features of coal preparation and carbonization that affect the resultant coke will be discussed. An attempt will also be made to indicate the effect on blast furnace operation of significant irregularities in these properties.THE FUNCTION OF COKE IN A BLAST FURNACECoke has four important functions in a blast furnace:1. To reduce the oxides of iron and other elements to metal and to provide the carbon absorbed by the iron.2. To supply the necessary heat for the process.3. To provide an open supporting structure in which the descending ore and limestone lie exposed to the action of the ascending gas.4. To provide voidage in the bottom of the furnace, so that iron and slag can accumulate in the hearth.

Jan 1, 1957

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

n the early days of the Hauraki goldfield (1866 to 1889) almost the only system of ore treatment was wet crushing followed by copper plate amalgamation. A further saving of bullion was in most cases obtained from the tailings by means of pans or berdans. Though this system was not always as efficient as might have been desired it answered fairly well for the bulk of the gold-bearing quartz of the Thames and Coromandel districts, where the gold occurs chiefly in the form of visible particles, and there is not a great deal of silver. It failed, however, with most of the ore found in the Upper Thames or Ohinemuri district, especially in the Karangahake and Waihi portions of the field. In those days the cyanide process was not, and the usual prescription of the mining " expert" was smelting. At Karangahake, many attempts were made to discover a payable method of treatment for the so-called" refractory" ore, but on thewhole with very 'little success, and the district struggled along for a number of years without adding very materially to the production of gold in New Zealand. At Waihi, the Martha Co.'s stamp battery treated by wet crushing and copper plate amalgamation some 18,000 tons from the Martha Reef, worth probablyat least £4 per ton, but the average return was considerably less than £1 per ton, a sum which barely paid working, expenses, and consequently the shareholders were glad...

Jan 1, 1903

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By Mohammad Eslami

The Tabriz-Urmiyeh Highway shortens the distance of north-western cities of Iran by about 130 km, resulting in improved access and efficient transit between Iran and Europe through Turkey. The highway crosses the Urmiyeh Lake, an inland lake surrounded by mountains. Due to the circulation of salt-water in the lake and the necessity to continue shipping between adjacent ports, a waterway should be kept open. Consequently, a bridge was built to provide access of marine traffic. A causeway bridge had a length of 1,260 m, comprising of 19 spans. In construction of the bridge, more than 400 piles having a total length of 32 km have been driven. For design of piles different methods have been used such as static analysis, dynamic testing, and correlations to in situ tests, such as cone penetration test (CPT). This paper presents construction of bridge substructure, full-scale piling tests, and methods of analysis used in the evaluation of the deep foundation capacity. The presentation includes an assessment of four current direct CPT and one CPTu methods to calculate the bearing capacity of the piles. It was found that the CPTu and dynamic testing are two suitable tools for rapid and optimum pile design and verification.

Jan 1, 2010

By P. Share

As part of JAGUARS (JApanese-German Underground Acoustic emission Research in South Africa), high-resolution tiltmeters were installed during 2007 at Mponeng gold mine, South Africa, in an attempt to study and understand the risks posed by in-mine seismic events and to subsequently use the knowledge gained to mitigate these risks. In December 2007, an M2.2 event occurred at Mponeng and was detected by the tiltmeters installed. The tilt expected for the M2.2 event is modelled through the use of numerical and analytical tools and utilizing, as input parameters, characteristics of the event such as the rupture area, the amount of slip, elastic properties of the rock, the state of stress before the event occurred, and frictional parameters of the rupture. The calculated tilt values are correlated and compared with the recorded data, and are found to be of the same order. Certain input parameters, such as the initial rupture point, are further constrained by varying them, during modelling, until the calculated and observed tilt values are approximately equal. From modelling, it can be concluded that the rupture point had to be closer to the location of the tiltmeters. In addition, possible locations acting as source areas for the observed aftertilt are determined. Further modelling still needs to be done to quantify the effects of the tunnel close to the tiltmeters and plastic deformation of the rock mass. Keywords high-resolution tilt data, Mponeng gold mine, M 2.2 seismic event, analytical modeling, numerical modeling, rupture plane.

Oct 1, 2013

By M. Vanpée, H. G. Wolfhard

Jets of hot gases issuing into explosive gaseous mixtures are efficient agents of ignition . The ignition temperature is defined as the temperature of the jet as it enters the cold explosive mixture which is just high enough to produce ignition . Such data have been published recently.5/ The investigators note especially that no correlation seems to exist between hot - gas ignition temperatures and spontaneous ignition temperatures , although there is a rather loose relation with limit flame temperatures . Before a more quantitative theory of the hot - gas ignition process can be attempted effectively , several questions must be answered : ( 1 ) Can the reactions leading to ignition be described by an Arrhenius type activation energy? ( 2 ) Is ignition preceded by an induction period ? ( 3 ) What is the rate - determining process of the ignition ? (4) And how does turbulence affect this type of ignition ?

Jul 1, 1960

By Freddie Hunter

An underground mining method for extracting an eight metre (26') coal horizon, containing a sandstone layer. A decrease in the thickness of the rock strata between the number two and number three seams of the Sasolburg Coal Field, has resulted in a total mining horizon approximately eight metres (26') thick. This parting varies in thickness and competency and in some areas is impractical to cut with a continuous miner. In addition, the general mining area is highly jointed. The top seam is first mined to a normal bord and pillar plan with a continuous miner. The bottom seam is then mined by selectively undercutting the stone parting constituting the floor of the top seam. In areas where this parting is between 0.75 - 2.50 metres (29.5" - 98") thick, it is suspended from the primary roof support installed when mining the top seam. Secondary, high extraction retreat mining is then undertaken in the coal pillars adjacent to the suspension supported headings in the bottom seam. Left in-situ, the parting provides lateral support to the pillar sidewalls in both the top and bottom seams, enabling high percentage extraction rates in what was previously thought an uneconomically mineable area. The paper proposed, presents the challenges and practical implications of executing the mining method, including the primary roof control of the top seam and the stone parting between scams.

Jan 1, 2003

By K. Oraee

The empirical rock failure criteria play an important role in predicting the mechanical behavior of rocks, since affecting parameters on the behavioral properties of rocks are complex and numerous. Usually the empirical failure criteria are obtained by statistical methods, namely by means of fitting the mathematical function onto the experimental data. For evaluation and verification of the results, however, the quality and accuracy of the fit must be considered. This paper studies the efficiency and accuracy of conventional empirical rock failure criteria using a new approach, which is based on the analysis of uncertainty amplitude on the constant parameters of each criterion. The approach adopted here, is based on the combination of some parameters such as Mean Squared Error (MSE), Root Mean Squared Error (RMSE), type of function, degree of freedom and the confidence level of constants. Correlation coefficient (R2) is then a comprehensive test and can be used effectively for comparison and accuracy of empirical rock failure criteria.

Jan 1, 2012