Search Documents

By Qingchun Yu, Bin Yang, Yong Deng, Heng Xiong, Fei Wang, Minxiu Chen

"Metal aluminum produced by non-electrolysis process received much attention due to its lower energy consumption. In this paper, carbothermic reduction and carbothermic-chlorination of alumina in normal pressure and vacuum were studied. The products were examined by means of XRD, EDS and SEM. During the carbothermic reduction process using carbon reductant in normal pressure, no metal aluminum was found. However, when coal was used as reductant, a mixture containing metallic aluminum, A14C3, and silicon was obtained, but metallic aluminum couldn't be separated from the mixture. During the carbothermic-chlorination process in vacuum, Al404C and Al4C3 were produced by the reaction between alumina and carbon, and Al Ch gas reacted with Al404C and Al4C3 to produce Al Cl gas. Metallic aluminum was produced due to the disproportionation of A!Cl gas and condensed on the collecting plate. Meanwhile, the initial temperature of carbothermic reduction of alumina reduced in vacuum compared with that in normal pressure.IntroductionIndustrial production of primary aluminum is carried out in alumina cell by the so-called Hall- Heroult process, necessitating the use of very high currents of low voltage. The alumina from which metallic aluminum is gained must be chemically pure, otherwise impure metal results. The main drawbacks of the electrolytic production are its very high energy consumption, the release ofperfluorocarbons, and the high specific C02 emissions [1]. During the past years, there were a lot of attempts to produce metallic aluminum by carbothermic reduction of A1203 [2, 3]. Cox [4] determined the vapor pressure over the A1203-C system and performed X-ray diffraction analysis of condensed products. It was demonstrated that an increase in the carbon content in the system leaded to the sequence of transitions: A1203~Al404C~A1zoc~A14C3 ~AI [5]. In any carbothermic reduction process for aluminum, extremely high temperatures (2000 °C ) were required [6]. In spite of considerable effort, the carbothermic reduction of alumina to aluminum remains a formidable technical challenge, due to the high temperatures required, and to the formation of aluminum carbide and oxycarbide byproducts [7]."

Jan 1, 2013

By Sui Xue

A process has been developed from laboratory-scale experiments for the aqueous processing of various lead-bearing wastes. The process exploits the limited solubility of lead in sulfate-rich solutions to effectively separate lead from other metals. The lead sulfate is then completely converted to lead carbonate using sodium carbonate and ammonium carbonate. The effectiveness of this conversion was observed to be sensitive to the solution pH and carbonate concentration. The final stage of the process uses low temperature calcination of the lead carbonate to form PbO. Yellow lead oxide (massicot) is readily formed if calcination is conducted at a temperature at or iibove 50G°C, wlule red iead oxide (iitharge) is formed at temperatures near 450°?C. A complete economical analysis of the process will be discussed.

Jan 1, 1996

By Gaballah I.

Elimination of arsenic, mercury and zinc from synthetic solutions containing H;\A.sD4. HgCI2 and ZnCI2 using modified barks was investigated. The pH range was varied from ?1 to 10. The initial concentrations of individual element were 10,100 and 1000 ppm. More than 99 % of mercury and 65 % of zinc cations were removed by the modified bark .. In this case, the modified bark reacts as a cation exchanger leading to the release of ' two protons for every HgII or ZnII fixed by this material. About 30 % of arsenic was eliminated from the solution. This 'low efficiency could be attributed to? the presence of arsenic ,as. anion. Decontamination of a treated industrial effluent containing 4 ppm of ion? metals was performed on a pilot plant scale by the modified bll(k. More than 70'% of these ion metals were eliminated.

Jan 1, 1995

By Ramana G. Reddy

Thermodynamic modeling and experimental study on impurity capacities and their distribution between mattes or metal and slags in smelting, converting and refining of non-ferrous metals was discussed. A brief review on the recent developments in copper smelting and converting is presented. The analysis showed that, copper smelting capacity increased by a factor of 10 since 60's, smelting rate increased by a factor of more than 5 and process fuel equivalent decreased by a factor of 2. A thermodynamic model for prediction of impurities capacities in slags and their distribution in mattes and slags was developed. The impurities capacities (i.e. sulfur and arsenic) of slags were calculated a priori with no adjustable parameters using the Reddy-Blander model. The capacities predictions were made in a wide range of matte and slag compositions, Pso, and temperatures in conditions pertaining to copper and lead industrial slags. The calculated results for sulfide and arsenate capacities are in good agreement with the available experimental and industrial copper and lead industrial slags data. The sulfide and arsenate capacities in copper slags (fayalite, ferrite and olivine) and lead slags are reviewed. The application of RB model predicted ratios of 02 and S2 partial pressures in industrial copper smelting processes are discussed. Application of this model for the prediction of Sb, Bi and other impurity capacities and their distribution ratios in mattes or metal and slags, in industrial smelting and refining processes is discussed.

Jan 1, 2003

By U. Kammer

The reduction of the lead content in the separator fraction produced during the mechanical processing of spent lead-acid batteries is an important environmental and economical issues. The reduction of lead down to less than 1 percent is very difficult using hydroseparators that are common in battery recycling facilities. Very promising results were achieved performing experiments on a test rig using a new technology in battery treatment: a discharge-type jigging unit. The materials is fed onto the jigging bed and transported through the machine. Due to the intensive movement of the feed, an additional washing effect is also obtained in addition to separation of the lead and plastic fractions. The knowledge gained from this development work at UVR-FIA GmbH in Freiberg, Germany, led to a patent application. This paper focuses on the results of the development work and the start-up and one year's operation of the industrial-scale application at Harz-Metall GmbH in Goslar, Gennany.

Jan 1, 2000

By Avijit Moitra

The behavior of the solidifying shell in the early stages of solidification has an important influence on the final quality of continuously-cast steel slabs. In order to understand the thermal and mechanical behavior of the shell, a two-dimensional transient piecewise-coupled finite-element model has been developed. The model simulates a transverse section of the slab as it moves down through the mold and incorporates the effects of heat conduction, solidification, shrinkage, turbulent fluid flow, thermal distortion of the mold and the visco-plastic behavior of the steel. Coupling between the thermal and the mechanical model is based on the mutual dependence of heat transfer across the interface between the shell and the mold and the size of the gap. The effects of mold distortion and taper on the gap size are also included. The effect of fluid flow has been incorporated via a heat flux imposed at the solid-liquid interface, which is obtained from a separate fluid flow model. The high temperature creep and plasticity of the steel is incorporated through a unified constitutive law defining the inelastic strain rates as a function of temperature, time and stress state. The model can be applied to various problems in continuous casting, such as the formation of surface defects and the design of mold taper.

Jan 1, 1992

By T. Wang, R. G. Reddy

"A new eutectic of LiNO3-NaNO3-KNO3 ternary system was calculated by using thermodynamic modeling and the eutectic temperature was predicted to be 389.15K. The melting point was determined using Differential Scanning Calorimetry (DSC). On repeated measurements, it was found that the melting point of the eutectic composition showed excellent reproducibility with the predicted value. The heat capacity was also measured using DSC and the data as function of temperature were fit to polynomial functions. Subsequently, the thermodynamic properties such as enthalpy, entropy and Gibbs energies of this novel ternary eutectic salt mixture were deduced as function of temperature.IntroductionIn these days, the provision of the large amount of energy required in the peak period relies more and more on the parabolic trough solar power plant and it works by utilizing the thermal transfer fluid. Consequently, the development of inoovative thermal transfer fluid with higher energy storage density is paramount to lower the expense for generating energy [1-4]."

Jan 1, 2013

By William Petruk

The Kidd Creek base metal deposit near Timmins, Ontario contains around 0.15 wt% Sn, mainly as cassiterite. The cassiterite occurs largely as inclusions in sphalerite, with 85% being in grains smaller than 18.5 micrometres in diameter. Concentrates and tails from the company's Cu, Pb and Zn circuits were studied to determine the liberations and recoveries of cassiterite in the products. The ore had been ground to about 65.% minus 44 micranetres in diameter (-325 mesh); 55% of the cassiterite was liberated. About 92% of the liberated cassiterite and 70% of the unliberated cassiterite were in the concentrator tails, and 20% of the unliberated cassiterite in the zinc concentrate. The company had attempted to recover the cassiterite from the concentrator tails by gravitational methods but recoveries were low. The grain size of the cassiterite in the gravity Sn concentrate was similar to the grain size of the liberated cassiterite in the concentrator tails. Research on flotation of the fine grained cassiterite from Kidd Creek ore has been conducted,

Jan 1, 1990

By A. Christlo

Short circuit detection in 1984 involved nine inspectors for production rates of 43,000 tpa. Trials indicated the feasibility of applying cell voltage monitoring to short circuit detection and improving operational efficiency. A computerised cell voltage monitoring system was commissioned in February 1986, to read voltages from 648 cells. The system incorporates 16 evenly distributed work face units which communicate with a central computer system. Provision has been made in the computer program for the automatic adjustment of cell reference voltages. This allows for the effect of polarization and other process variables which might other wise interfere with short circuit detection. The work face units can continue to work independently for several days should this become necssary. Current efficiencies have been maintained and the number of inspectors reduced from nine to five.

Jan 1, 1987

By F. E. Brinckman, G. J. Olson, D. Johnsonbaugh, T. K. Trout

"Microbiological metal recovery is an emerging technology likely to play an increasing role in commercial ore leaching, metal removal from process and waste streams, and perhaps ultimately in processing to yield metal products in specified forms or oxidation states. We are studying the potential for using microorganisms for the recovery of elements important to emerging materials technologies and for which domestic supplies are limited and/or low grade. Examples to be discussed include the bioaccumulation of yttrium and gallium. These elements are important in the production of new superconductor and semiconductor materials. However, limited domestic reserves and technologies for their recovery may cause supply problems. Microbiological processes may offer new techniques for recovery of these and other strategic elements.IntroductionMicroorganisms in ore leachingMicroorganisms assist in the commercial leaching of copper and uranium from low grade ores (1,2) and recently have been shown to have immediate commercial potential for the pretreatment of refractory gold ores to increase the gold-cyanide recovery yield (3). Copper bioleaching is the best known example of biotechnology applied to metal recovery. Copper can be recovered by commercial leaching of huge piles or dumps of low grade sulfidic ores and waste materials, which are not otherwise processable. Microbial activity in the leach dump environment oxidizes metal sulfides to soluble metal sulfates:"

Jan 1, 1988

By Neng-Wen Yu, Miao Wang, Ji-He Wei

The mass transfer characteristic between powder particles and liquid steel in the RH-PTB (Powder Top Blowing) refining has been investigated in a water model of 1/5 scale for a 90t RH degasser. The sodium chloride powder with analytical purity has been used as the flux for blowing. The mass transfer coefficient of the liquid side has been determined under the conditions of RH-PTB process. The influences of the main technological and structural parameters on the mass transfer rate have been examined. The results indicated that under the conditions of the present work, the mass transfer coefficient on the liquid side increases with raising the lifting gas blowing rate, inner diameter of the up-snorkel, circulation rate of the liquid and particle size of powder flux. And it decreases with an increase in the inner diameter of the down-snorkel. It is in the range of (l.36-7.30) x 10·4 mis, the appropriate dimensionless relationships have been obtained as follows:

Jan 1, 2000

By W. K. Connor, O&apos

The Bureau of Mines has conducted beneficiation, carbothermic reduction, and leaching tests of Mn oxide ores as part of its evaluation of the Mn and Co resources of the West- Central Arkansas District. The major Mn oxides in the ore include cryptomelane, psilomelane, pyrolusite, and lithiophorite. Cobalt is contained within the Mn oxides. Nonbeneficiated ore was reduced at 800' C with coal and leached in ammonium sulfate and ammonium carbonate leach liquors. Ore concentrates were calcined at 600" C prior to reduction under the same conditions as the raw ore. Head analyses reported up to 21 ptt Mn and 0.11 pct Co. Extractions of 70 to 90 pct Mn and 40 to 60 pct Co were achieved.

Jan 1, 1992

By P. N. Anyalebechi

The effects of application of steady and pulsed electric current on the cast microstructures of ingots of a 7050 type aluminum alloy have been experimentally investigated over a solidification rate range of 0.1-10 K/s. This involved the application of an electric current of 465-930 mA/cm2 of melt surface area to laboratory-size ingots solidified in a unidirectional manner. Within the ranges of electric current density and solidification rate investigated, the applied electric current reduced the average dendrite, grain, and second-phase particle size. It also made the size distribution of the second-phase particles more uniform. The mechanism for the observed refinement of the cast microstructure by the applied electric current is not well understood. The potential effects of heat-induced local convections, shear stress-induced fragmentation of dendrites, increased temperature gradient due to Joule heating and the thermal and constitutional supercooling engendered by Peltier, Thompson, and Joule heating are discussed.

Jan 1, 2009

By T. Kimura, H. Ohba

"Much effort has been made to reduce the energy requirement in zinc electrowinning. In order to keep energy consumption low, either to make cell voltage low or current .efficiency high is necessary. Decrease of cell voltage practically depends on how to reduce ohmic resistance in the electrolyte and the anode crust. To realize these, new concept was proposed and the pilot plant has been operated. The space between a cathode and an anode is halved by utilizing the frame insulator. With these frames the anodes and cathodes compose of a unit of electrodes, and this unit is handled by newly designed electrode handling machine (E.H.M.). The process includes lifting up electrodes, expanding the space between a cathode and an anode, cleaning them, stripping the deposited zinc and returning the unit to the cell. As a result, cell voltage is kept as low as calculated and predictable energy reduction has been achieved. IntroductionIn the recent trend of a rapid appreciation of the Japanese yen, Akita Zinc Refinery of Mitsubishi Metal Corporation has been confronted by problems of relatively high operating costs. In order to compete with other overseas zinc refineries, it is necessary to reduce the cost of zinc production, especially the cost of electric power which now accounts for .up to 35 % of the entire cost of production. Three fourth of the electric power used at Akita Zinc Refinery is for the electrolysis. Therefore it is extremely important to reduce the cost of electrolysis.There are two possible measures for solving the problem; one is to use more nighttime electricity taking the advantage of its inexpensive power price, and the other is to reduce electric power consumption.As a part of a rationalization plan carried out in 1986, Akita Zinc Refinery increased the number of operating cells. As a result, when nighttime electricity is used, the silicone rectifier has been able to operate at full capacity. Moreover, by new schemes of ""increase of area for electrodeposition by ralslng the liquid level of electrolyte"" and ""increase of the number of electrodes in each cell"", current density could be lowered and as a result, the electric power consumption has been improved. In order to raise nighttime ratio even higher, installation of an additional rectifier and cells would be required."

Jan 1, 1988

By Alicia Esther Ares

This study was conducted to investigate the directional solidification of Zn-20%A1 and Zn20% A1-1O%Si-3o/oCu alloys under different conditions of heat transfer at the metal/mould interface. The type of structure obtained in both cases was analyzed and related to the solidification thermal parameters such as cooling rate, growth rate, thermal gradient and recalescence which were determined from the temperature versus time curves. These parameters were correlated with the structure-like length of columnar grains and size of equiaxed grains. The metallographic analyses were done performing quantitative metallography and composition analysis of the different alloying elements along the cast samples by SEM (Scanning Electron Microscopy) and EDXA (Energy Dispersive X-Ray Analysis). Correlations between properties, structures and thermal parameters were found.

Jan 1, 2008

By W. K. Choi

Stainless steel exposed to wet environments at ambient temperature is subject to the formation of a surface biofilm. Depending upon the prevailing environmental conditions (dissolved oxygen, pH, Eh, concentration of cationic/anionic species), the biofilm may stimulate corrosion through formation of differential aeration zones and concentration cells. Corrosion significantly impacts the United States economy, since on a yearly basis, corrosion induced losses are estimated to be over $200 billion. A large portion of this corrosion is imputable to bacterial activity, and basic information is needed for a better understanding and control of the biocorrosion phenomenon. The present study has investigated the influence of Thiobacillus ferrooxidans in the corrosion of American Iron and Steel Institute (AISI) 304, 316 and 416 stainless steel samples. The formation of biofilm and microstructural changes on the surface of stainless steel samples and their weldments were assessed by microscopic examination, and the changes in the mechanical properties by stress-strain measurements. The significance of the results will be discussed.

Jan 1, 1993

By I. Gaballah

Decontamination of synthetic solutions of copper acetate, chloride, nitrate and sulfate containing 10, 100 and 1000 ppm of copper, using chemically treated barks has been studied. Metal percent removal from solutions depends on the pH and the initial concentration and to some extent on the salt used. It varies from 40 to 99 % of the solution initial metallic ion's content. The maximum retention capacity of the treated bark varies from 31 to 43 mg of Cu per gram of dry modified bark. Bark loaded with copper had been analysed by Scanning Electron Microscopy and lnfra Red spectroscopy. Cu is uniformally distributed in the bulk of the bark. No copper segregation is observed. It seems that copper is bound to the acidic sites of the bark. Anions are not detected on the copper loaded bark neither with the SEM or with the IR spectroscopy.

Jan 1, 1993

By Linlin Wu, Marlen Bertram, Chris Bayliss, Bernard de Gelas, Samantha Jones, Kurt Buxmann

"Environmental management is one of the industry cornerstones of sustainable development. In order to understand fully the environmental aspects associated with the raw material acquisition, production, use, and end-of-life operations of aluminium products, the Aluminium Industry has developed an approach based on Life Cycle Analysis (LCA) methodology.Within this framework, the Primary Aluminium Industry has established a global Life Cycle Inventory (LCI) data set. Inventory flows include inputs of raw materials, energy and water, emissions to air and water, and solid waste.This paper presents the latest LCI data update by the International Aluminium Institute for the year 2010, based on a survey of aluminium plants globally, including bauxite mining, alumina refining, anode production, electrolysis and casting. This update also includes some performance tracking based on the last LCI data collection in 2005, reflecting progress in efficiency and technology, as well as changes in the geographical location of the industry [2010 data pending]. IntroductionIn 2010 the Primary Aluminium Industry produced a total of 41 Mt of aluminium. The International Aluminium Institute (IAI) membership represents approximately 70% of total global production. The industry recognises the importance of co=itting to reducing the environmental impacts of producing primary aluminium, and the significance of working towards a more sustainable future. As part of this co=itment the IAI has developed an in depth Life Cycle Inventory programme, in which data is collected every five years, with supplementary key metrics collected annually.In 2003 the IAI released its first Report ""Life Cycle Assessment of Aluminium: Inventory Data for the Worldwide Primary Aluminium Industry"" based on the year 2000 with an update Report released in 2007, based on 2005 data.This paper presents the latest update for the year 2010 [2010 data pending]. It has been prepared with the same view of collecting all significant Life Cycle Inventory data (raw materials and energy use, air and water emissions and solid waste generated) associated with producing primary aluminium ingot from bauxite ore, with worldwide coverage. The intended purpose of the Inventory Report is to accurately characterize resource consumption and significant environmental aspects associated with the worldwide production of primary aluminium. It reflects the fuct that primary aluminium is a globally traded co=odity."

Jan 1, 2012

By I. Gaballah

The kinetics of oxychlorination of pure CI-2O3 with C12+02 gas mixtures is studied by ThermoGravimetric Analysis (TGA) in non and isothermal conditions up to 1000 °C. The reaction of Cr2O3 with C12+O2 chlorination gas mixtures starts at about 550 °C and the reaction product is CrO2Cl2. The oxychlorination rate of Cr2O3 is almost proportional to the chlorine partial pressure and to the fourth root of the oxygen partial pressure in the chlorinating gas mixtures. At 800 °C, the maximum chlorination rate is obtained using a gas mixture having a C12/O2 ratio equal to 4. The apparent activation energy of the oxychlorination reaction of Cr2O3 is 87 and 46 kJ/mol at temperatures lower and higher than 650 °C, respectively. By varying the chlorine and the oxygen partial pressures of the oxychlorinating gas mixtures at temperatures higher than 550 °C, it is possible to extract selectively the chromium chlorinated compounds from the chromium bearing materials. a. Laboratoire Environnemem et Minéralurgie, BP 40, 54501 Vandceuvre, France, b. École Nationale Supérieure de Géologie, Rue du Doyen Marcel Rouhault, 54501 Vandoeuvre Cedex, France, c. Centre National de la Recherche Scientifique, 3 rue Michel - Ange, 75794 Paris Cedex, France, d. Insritut National Polytechnigne do Lorraine, Rue de la Font de Haye. 54501 Vandceuvre Cedex, France.

Jan 1, 1997

By K. Osseo-Asare

The molecular structural and solution chemical characteristics that underlie the surface activity of solvent extraction reagents are highlighted, with particular emphasis on the tendency towards reverse micelle and microemulsion formation. The physicochemical factors that lead to microemulsion-enhanced solvent extraction with chelating extractants are elucidated Membrane-based contactor systems are described which are uniquely suited for enhanced solvent extraction with microemulsions. The possibility of combining solvent extraction with microemulsion-mediated materials synthesis is discussed.

Jan 1, 1996