Search Documents

A study of iron-removal from copper leachate by limestone precipitation followed by direct eltctrowinning of copper has been conducted. The influence of the process parameters: amount of precipitant, contact time, temperature, agitation intensity, solution acidity, and initial iron concentration on iron-removal was investigated. The effects of electrowinning time, cell voltage, solution acidity and temperature on electrowinning of copper were also investigated. The leachate contained 1.20 g/l cu2+ and 7.41 g/l total iron at pH 2.27. After contacting with 14 g/l precipitant for 2 hours, 97.5 % of the iron was attenuated and 98.4 % of the copper was recovered. With the following electrowinning conditions: 3 lead anodes, 3 stainless steel cathodes, 2.5 V, 39.41 A/m2 and 10.7 g/l H2S04, copper recovery-was 98.4 %. Purity of copper powder produced was greater than 99.0 %.

Jan 1, 1999

By G Hope, C Young, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing as it is refractory, increasing cyanide and oxygen consumption, and enviromnentally hazardous. Selective leaching and treatment of the arsenic would prove advantageous to conventional gold leaching methods. The reactivity of enargite samples from Montana, US and Quiruvilca, Peru were studied under alkaline conditions, pH range of 8-13, using a cyclic voltammetry corrosion cell setup. Raman spectra of the surface were taken during and after cycling to compare surface species against theoretical predominance diagrams. Under slightly oxidizing conditions, covellite (CuS) peaks were found on the surface in a short matter of time, above - 200m V vs SHE for pH 9-13, suggesting arsenic leaching, but for longer conditioning times, elemental sulfur peaks were also found, which created a passivating surface layer. By operating above pH 12, under reducing conditions, ~-500mV vs SHE, arsenic can be leached as a thioarsenate (AsS4-xOx3-), without sulfur formation.IntroductionEnviromnental limitations on pyrometallurgical processing of arsenic has pushed the desire to process enargite-, Cu3AsS4, bearing concentrates towards a hydrometallurgical solution. Attempts to process can be broken down into two categories - the co-dissolution of arsenic and copper under acidic conditions or the selective leaching of arsenic under basic conditions. The selective leaching of arsenic would preferably leave behind a chalcocite, Cu2S, or covellite, CuS, phase that would be more amenable to conventional processing methods of the copper and gold industries. These methods employ bi- or poly-sulfides to leach arsenic as Assl· [1-4], hypochlorite leaching [5-7], ammoniacal leaching [8] or fine grinding to mechanically activate the enargite surface and increase normally slow reaction kinetics[9]. This study looked into the surface formations of an enargite electrode under alkaline conditions, in a pH range from 8-13, as it cycled from -1000 mV to 1000 mV vs SHE. The understanding of the formations and under what conditions they form will be helpful in further development of any of the aforementioned processes."

Jan 1, 2012

By Katie Schumacher, Greg Roset, Dayle Flynn

The Columbus Processing Complex of the Stillwater Mining Company began operations at Columbus, Montana in 1990 based on electric furnace smelting treating a precious metals concentrate from the nearby Stillwater mine and mill. Since that time, the smelter plant has been expanded in stages in order to treat recycled materials in addition to the concentrate. This paper describes a number of changes made at the plant to effectively handle recycled materials.

Jan 1, 2014

By Nedam Abed

A fundamental study of the sonochemical leaching of chalcopyrite in ferric ion media has been performed to understand and quantify the effects of sonication and other parameters on leaching reactions. The study covers sulfate and chloride media. The main leaching reaction: CuFeS2(s) + 4Fe3+(aq) Cu2+(aq) + 5Fe2+(aq) + 2S(s) (1) was found to be dependent on temperature and initial particle size, but less dependent on ferric ion concentration. Leaching kinetics were not affected by ferrous ion concentration or the amount of chalcopyrite added. Leaching was performed under a variety of sonication and leaching conditions. Reaction stoichiometry was confirmed through detailed wet chemistry analysis and mass balance calculations. The use of ultrasound activation showed a clear improvement in leaching kinetics and amount of copper extracted, sonication having a catalytic-like effect on the leaching reaction. Compared to experiments without sonication, reaction rates were 2-3 times faster at the same temperature, and could be faster by a factor of 20 for the same initial particle size. Regardless of initial particle size, the amount of copper extracted was comparable under sonication, and could be twice that under chemical leaching, implying the avoidance of fine particle grinding. Sonochemical leaching was found to be only temperature dependent, where the best copper extraction was at 75C. Leaching was further enhanced by the use of a grinding aid. The leaching behavior of chalcopyrite particles remained similar with and without ultrasound activation, implying that the known passivation mechanism in the oxidative leaching was not eradicated. Sonication resulted in coarse particle breakage (ultrasonic milling). Sonication did not contribute to particle passivation, as affirmed from different leaching procedures and sonication in aqueous and organic media. Parabolic leaching kinetics were confirmed for leaching experiments.

Jan 1, 2003

By S. S. Ibrahim

The left behind material after the combusion of fossel fuel in some power stations in Cairo; weighing tens of tons every years, was investigated. The material called "Fly Ashes" containing 7.5% Ni, 10.0% V and 9.50% Cr; could be considered as a promising source of such valiable elements. As well as the small grain size (050 70 "m) of the material, and besides the complexity of their formation history, hydrometallurgical methods appeared to be the effective technique to deal with. Yet, preconcentration is possible by means of magnetic and gravity separation methods. The end product is assaying 16.60% Ni and 20.2S!; V with weight recovery of about 60.15%.

Jan 1, 1995

By Dinabandhu Ghosh

The stability diagram of the ternary system Ti-C-O is drawn in the present work for four temperatures, 1473 K, 1573 K, 1673 K and 1873 K, showing the stability fields of TiC, Ti, TiO, Ti2O3 and TiO2. An analysis of the system reveals that it is not possible to produce Ti in a carbon-saturated system; instead, the stable product is TiC. However, Ti can be an equilibrium product in a carbon-unsaturated system at prohibitively low values of pCO and pCO2; for example, at 1873 K, these limiting values are: pCO = 10-6.76 atm and pCO2 = 10-13.36 atm, which, when exceeded, produce TiC and TiO respectively. The magnesiothermic reduction is examined through the stability diagram (log pO2 vs. 1/T) of the system Ti-Mg-O, drawn for a number of pMg values, presenting the pairwise stability fields such as Mg(l) + Ti(s), Mg(v) + Ti(s), MgO(s) + Ti(s), etc. The diagram shows that magnesium reduction of TiO to Ti is possible only at T < 1641 K with pMg = 1 atm and only at T < 1569 K with pMg = 0.5 atm. An experimental scheme for Mg vapor reduction of TiO2 is proposed in which an argon stream is passed over a Mg(liquid) evaporator at temperature T1 (say, 1234 K); the resulting Ar-Mg mixture at 1 atm is subsequently flown over a bed of TiO2 at temperature T2. A thermodynamic analysis establishes that complete reduction to Ti is possible and that the best results are obtained when T1 = T2.

Jan 1, 2006

By Krzyszof Borowiec

With the aim of determining the thermodynamic conditions for sulfation of impurity elements, in particular magnesium, in titaniferous slags the equilibrium gas composition for the sulfation reaction: MO + so2 + 1/2 02 = MS04 has been studied by an EMF technique with a solid zro2 + Cao electrolyte. Here M denotes the impurity elements: Mg, Ca and Mn, and the following _oxide systems have been studied: Ti02-MgO-Fe2 o 3 , Ti02-MnO-Mn2 o 3 , and Ti02 -CaO-Si02 , all in the . temperature range 700-1000ºc. Reproducible EMF values were obtained by adding small amounts of -Na2so4 to the oxide-sulfate mixture. From the observed results the Gibbs energy of formation of the phases Mg 2Ti04 , MgTi03 , MgTi 2o 5 , MnTi03 , CaTi03 , and CaTiSio5 , as well as the activity of MgTi05 in the solid solution with Fe2Ti05 have been calculated. The results show that, from a thermodynamic viewpoint, sulfation of these impurities in titaniferous stags i:s favorable- at around and below 800ºC.

Jan 1, 1985

By D. D. Harbuck

The U.S. Bureau of Mines recently identified a significant new source of scandium in an Oklahoma tantalum waste residue (approximately 0.24 pct Sc). Because scandium is a strategic and critical metal which the Department of Defense has classified for special consideration, the Bureau is researching methods of recovering scandium and associated metals from this and other process residues. A variety of operating parameters were evaluated to determine the best technique for recovering scandium. Testing showed that by sulfating the residue at temperatures as low as 150&apos; C for reaction times as short as 0.5 hr, over 94 pct of the scandium converted to a water soluble form. Solvent extraction using DEHPA selectively recovered 100 pct of the scandium from the water leach solution.

Jan 1, 1992

By John W. Lund

The Geo-Heat Center has been investigating the utilization of waste silica from the Cerro Prieto geothermal field for several years. The main objectives of the research were to com-bine silica with various additives to (1) form bricks for low cost housing, and (2) to produce a suitable road surfacing material. The various additives that were tested included hydrated lime, portland cement, plastic fibers, asphalt cement and emulsified asphalt. The silica-cement combination produced the strongest bricks and had the best weather resistance, whereas, the silica-lime combination produced the bricks with the lowest thermal conductivity and specific gravity density. The addition of plastic fibers to the silica-lime mixture improved both strength and weather resistance. The combination of asphalt and silica is not suitable as a road surfacing material, however, silica-cement appears promising.

Jan 1, 2006

By Shadia J. Ikhmayies

"Cadmium sulfide thin films were prepared on glass substrates by the spray pyrolysis technique at a substrate temperature of 490°C. Some of the films were etched by HC1 in distilled water, others were heat treated in nitrogen atmosphere, and another set of films was first etched by HC1 and then annealed. Room temperature impedance spectroscopy measurements on the films were performed using coplanar geometry in the dark and in room light in the frequency range 20 Hz to 1 MHz. The experimental data were represented by complex plane diagrams and showed one well-defined semicircle in the high frequency region. Hence the equivalent circuit that models the CdS: In thin films was found to be a single RC circuit, which indicates the bulk conduction through the grains. The influence of treatments on the electrical properties was investigated.IntroductionCadmium sulfide (CdS) is a brilliant II—VI semiconductor material with a direct band gap of 2.42 eV at room temperature. It has many outstanding physical and chemical properties, which have promising applications in multiple technical fields including photochemical catalysis, gas sensor, detectors for laser and infrared, solar cells, nonlinear optical materials, various luminescence devices, optoelectronic devices and so on [1]. There are different methods to prepare undoped and doped CdS films, such as rf sputtering [2] chemical bath deposition (CBD) [3], pulsed laser deposition (PLD) [4], and spray pyrolysis (SP) [5-11]. Of these methods, spray pyrolysis represents the less expensive option, and can produce large area high-quality low cost thin films [12]."

Jan 1, 2012

By M. F. El-Demerdash

The activity distribution diagrams for different species in aqueous systems are developed. Computational method may be considered as an extension of the Activity-Term method introduced by the authors to construct EH-pH diagrams. In the Activity-Term method, all activities of different species are evaluated before deciding the most stable one. In the present study, a factor is assumed to allow for the conservation of the element. At any point, the total concentration of all species should contain only the input m moles of the element (elements) considered. This approach is applied to Zn-, 5-, and Zn-S-H2O and activity distribution diagrams are plotted as a function of pH, at different potential levels and at different temperatures.

Jan 1, 1990

By W. G. Davenport

This chapter extends our mathematical description of flash smelting to -nitrogen in the flash furnace blast. As in chapters 4 and 5, the discussion is limited to auto thermal smelting (no hydrocarbon combustion). Hydrocarbon combustion is introduced in Chapter 9. Outokumpu flash furnace blast is a mixture of air and industrial oxygen. Most of its N2 originates in the air portion of the blast. A small portion originates as an impurity in the industrial oxygen. The nitrogen entering a flash furnace must always be heated from its input temperature, 298 K in this chapter, to its off gas temperature, -1500 K. Energy must be supplied for this purpose. With auto thermal smelting, the energy is-provided by oxidizing extra Fe-and S.

Jan 1, 2001

By John A. Mavrogenes

The Texaco gasification system developed at the Monte Bello pilot plant efficiently bums petroleum-coke thereby producing syn-gas and electricity. This system produces more electricity than conventional burners, yet the only by-products are pharmaceutical grade sulfur and V -rich slag. Vanadium is known to exist in multiple valence states in compounds which possess a wide range of melting points and physical properties. Consequently, it becomes important to carefully regulate oxygen fugacity throughout the system in order to control vanadium valence state. Vanadium phase equilibria is presently poorly understood, in large part because of the multiple oxidation states of vanadium (-I, 0, +2, +3, +4, and +5) and the difficulty of unequivocally identifying the valence state(s) in many compounds. The operation of these gasifiers at approximately 1400°C is well above the melting point of V20S but considerably below the melting temperature of V02 and V 203. If J02 can be regulated to keep the burner within the V 205 field, slag material would more likely remain molten and more easily flow out of the bottom of the burner. In pure V oxides. the oxidation state is readily determined by microprobe analysis. where V20S (V+5) is 56% V, V02 (V+4) is 61.4% V, and V203 (V+3) is 68% V. However, V valence in multi-element phases (especially phases containing other elements of variable valence) cannot be resolved by microprobe analysis alone. Petroleum-coke gasification slags collected from within the gasifier under different oxidation conditions were studied by electron microprobe analysis (EMPA). X-ray diffraction (XRD). X-ray photoelectron spectroscopy (XPS) and Raman spectroscopy. Raman spectrometry in conjunction with microprobe analysis was found to resolve the valence of vanadium in the phases of these slags. Raman spectra collected from homogeneous single phase V-oxide standards in vacuum at low temperatures (-150°C) yielded peaks characteristic to each valence state. Gasifier slag samples are, however, much more complicated. Oxidized samples contain: fine grained (Ca. Mg, Fe. V) oxide matrix of variable composition, (Fe. V, Ni) spinel. (Fe, AI, V, Ni, Mg) spinel, V205laths, AI-Si glass blebs and Ni sulfides. Reduced samples contain: crystalline Ca-siIicate matrix, subhedral to euhedral (V, Fe, Mg, AI) spinel, subhedral V02, Fe and Fe-Ni sulfides, Fe-Ni alloys, and complex Ca-oxide matrix. The different spinel assemblages, the characteristic V-oxides and the distinctly different character of the matrices makes the oxidized and reduced slags readily discernible.

Jan 1, 1995

By Marco A. S. Aguiar, Luis G. S. Sobral, Vânia Mori, Paulo A. Medeiros da Silva

"Copper occurs in the crust of the earth, predominantly, as sulphides. Among the copper sulphide minerals, the chalcopyrite is the most abundant and the most refractory to the conventional oxidative processes. This work aims at developing an electrolytic process for treating a copper sulphides flotation concentrate, more precisely chalcopyrite (CuFeS2) and bornite (Cu5FeS4) in the percentages of 70 and 30%, respectively.This paper presents a low-cost operational electroleaching process for treating copper sulphides flotation concentrates, with a high chalcopyrite content. This research practical work aims at improving the copper extraction from that sulphide mineral, in a relatively short time with low-operating cost taking into consideration the influence of a cationic surfactant. The electrolyte of the electrolytic reaction system was a 2,0 mol.L-1 NaCl solution containing CTAB, a cationic surfactant. The electroleaching system contains one DSATM (dimensionally stable anode) anode and two nickel or copper foams (threedimension electrodes. During the electroleaching process the chloride ions are oxidized to chlorine at the anode surface, which in contact with the aqueous phase generate enough hypochlorite ions to oxidize chalcopyrite.The copper ions released from the chemical oxidation process are reduced at the cathode surface as metallic copper."

Jan 1, 2008

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to to7 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

By Yutaka Shiraishi

Two methods were developed to measure the viscosity of the slag from the glassy to the liquid states in an ascending temperature process. The first method employs rotating parallel plates within which is placed a solid cylindrical sample in line with a sphere. The second method uses a tube which is pushed into a sample held in a rotating crucible. Both methods were tested using standard glasses, including boron trioxide and NBS standard glass #711. The main difference between these two methods is in sample preparation. Comparative measurements between two methods were performed using a sodium boro-disilicate glass containing 5%mol of alumina. The results showed good agreement in the mid-range of glassy viscosities, 105 to 107 Pa.s. In the liquid state, there were no significant differences between the two methods.

Jan 1, 2003

The paper concerns an unconventional, yet promising, use of waste magnesite dust and fines. In India a significant amount of this dust is generated from some of the integrated iron and steel industries, refractory and cement plants, during calcination of raw magnesite. However. it is possible to utilize this dust, which is normally a waste, conveniently and economically for the production of magnesium. chemicals. A bench scale study was carried out to determine the rate of formation of sulfated com¬pounds of Mg.Ca,and Fe, inter alla, present in the dust system containing MeO constituents (in which Me=Mg.Ca,Fe,Si,Al etc.) Effects of various process parameters, which affect the reaction rate as also the purity of the product ,were also studied. Some work carried out to develop the process flow charts involving the salient steps to produce magnesium chemicals commercially is reported in the paper .

Jan 1, 1992

By A. Pagliero

The coulombimetric reduction method has been used as an evaluation technique for Pb-Ca-Sn anode corrosion in the LIX-SX-EW process. The proposed methodology involves three consecutive steps, i.e., cleaning, oxidation and reduction. They are carried out in the same experimental unit, in solutions containing 180 g/L H2S04 with and without the addition of cobalt. The authors have worked in a wide range of oxidation current densities, from 150 to 500 A/m2 for in a period from 0.5 to 120 hours. It can be concluded from the results that there would be a linear relationship between the applied electrical charge I*T (Coulomb) and the anode corrosion expressed as transformed Pb mass (mg), for solutions with or without the addition of cobalt. The exception is that for the last one the corrosion rate is 5 times faster, which was observed for every layer. From the evaluation of different corrosion layers, one can point out that its composition is mainly in the form of sulphate. In the presence of cobalt, about 67% of Pb would be as sulphate (PbSO4), about 27% as a basic oxide (PbO) and only 6% as oxide PbO2 on the surface. From this result, it appears that great transformations occurred in the metal/sulphate interface. Without the addition of cobalt, the proportion of oxide Pb02 on the surface increased up to 11.5%. According to the previous statement and considering that Pb was found mainly as sulphate, the authors recommend its determination be used as quality selection criterion. Its evaluation should be performed in the acid solutions with 200 ppm cobalt addition at an oxidation current density of 300 A/m2 for a period of 24 hours.

Jan 1, 1999

By R. Padilla, M. C. Ruiz, R. Villa

"Bismuth is an impurity in copper minerals where it occurs mainly as the mineral bismuthinite (Bi2S3). In smelting of copper minerals, most of the bismuth reports to the white metal, as a result, a substantial amount of bismuth accompanies the copper to the electrorefined cathodes. Thus understanding the behavior of Bi2S3 at high temperatures is crucial to eliminate bismuth before electrorefining. In this paper, some experimental data on the decomposition/volatilization of bismuthinite in nitrogen- oxygen atmospheres is discussed. The results indicated that in nitrogen atmosphere, bismuth volatilization occurs through a fast decomposition of bismuthinite to metallic bismuth and sulfur with subsequent volatilization of bismuth in the range 850-1100 °C. Similarly, in the presence of oxygen, bismuthinite decomposes to bismuth too, followed by oxidation to the non-volatile bismuth trioxide at temperatures higher than 750 °C. Both, temperature and partial pressure of oxygen affect significantly the bismuth volatilization and the oxidation rates.IntroductionCopper sulfide minerals are the major source for the production of metallic copper by pyrometallurgical processes, which are the dominant processes in the production of copper by selectively oxidizing the sulfide sulfur to SO2 and the accompanying iron in the concentrates to iron oxide, which can be conveniently removed as a stable slag.Generally, copper concentrates contain some deleterious minor elements such as arsenic, antimony, bismuth and lead, which are present as sulfides. These elements depending on their concentration may originate problems in the copper smelting processes and they can ultimately lead to a final copper product with unacceptable high levels of impurities.During the treatment of these copper concentrates by smelting, the impurities generally distribute themselves in the condensed and gas phases and they are eliminated mainly through the gas phase [1-3]. Thus, smelter off gases contains substantial amounts of volatilized impurity elements. For example, in the case of bismuth, the estimated distribution of bismuth in flash furnace smelting [2] was 15 % in the matte, 5 % in the slag and 80 % in the gas phase, and recently, for Outokumpu flash smelting Davenport [3] reported the distribution of bismuth as 30-75% in matte, 5-30% in slag and 15 -65 % in the off gas."

Jan 1, 2011

By Yotamu Stephen Rainford Hara

"The study focuses on the reduction mechanisms of copper, cobalt and iron during carbothermic reduction of copper-cobalt mineral sulphide concentrates in the presence of lime, in the temperature range of 1073K and 1273K. We have used three types of mineral concentrates which were derived from froth flotation from the Copperbelt region in Zambia. The reduction mechanisms were studied using thermogravimetric analysis in which selected reactions were stopped at different times for characterising the reaction mechanism using optical microscopy, XRD and SEM-EDX analyses. Using SEM-EDX analysis, we have analysed in details the stages of metallic phase formation during reduction process. Metallic cobalt and iron were embedded into copper, thereby permitting magnetic separation of the reduced metals even though copper is diamagnetic. Methods of preferential reduction of metal values were investigated by analysing the metallic phase formation.IntroductionIn conventional smelting or converting of copper sulphide minerals, metallic copper forms by giving off S02 gas on. Although in terms of overall energy balance the selective oxidation for metal production has major advantages, the process suffers from drawbacks in smelting complex concentrates containing copper, cobalt and iron sulphides minerals and these are: (i) cobalt and iron are oxidised, and consequently cobalt is lost into the slag phase. (ii) The volume of S02 gas produced is in low concentrations, which is insufficient for extracting sulphur or manufacturing sulphuric acid. The release of dilute S02 causes serious environmental pollution. The major cause for the loss of cobalt and iron into the slag, is due to that fact that the oxides of these metals are more stable than their sulphides. Since cobalt and copper are more valuable than iron, reducing conditions are required in a separate slag treatment reactor using electric arc melting for recovering the lost metal oxides from slag. This energy-intensive step makes metal making expensive.During chemical beneficiation of mineral sulphides (Cu2S, CoS, FeS) in the presence oflime (CaO), two types of equilibrium conditions may be set up either by forming CaS under reducing conditions, or by stabilizing CaS04 under oxidising conditions [l]. By comparison in the presence of carbon, CaS and metallic phases form, enabling the recovery of metals from sulphide minerals, which have been investigated by a number of authors [2-9]. During reduction of metal sulphide in the presence of lime and with carbon, it has been proven that the overall reaction le proceeds via two main steps: [5, 8, 9] (i) the anion exchange reaction between metal sulphides (MS) and CaO as shown in equation la, followed by (ii) the reduction of metal oxide (MO) via reaction lb."

Jan 1, 2013