Search Documents

By Susumu Imashuku

A pseudoternary phase diagram of the BaO?ZrO2?ScO1.5 system is established and the conductivities of the scandium-doped barium zirconate are measured in wet conditions. According to the phase diagram, the molar fraction of scandia in the barium zirconate phase that equilibrates with the cubic zirconia (ZrO2) and scandia (Sc2O3) phase is 0.03. On the composition line, where the molar fraction of barium oxide (BaO) is 0.50, the solubility of scandia into barium zirconate is 0.27 as a molar fraction of scandia. At around 500 °C, the conductivities of scandium-doped barium zirconate are estimated to be almost same as that of yttrium-doped barium zirconateThe activation energies for bulk proton conduction in scandium-doped barium zirconate (0.57 eV for BaZr0.90Sc0.10O3-d) are higher than that of yttrium-doped barium zirconate (0.44 eV for BaZr0.90Y0.10O3-d). In addition, the bulk conductivity of scandium-doped barium zirconate in this study is 10 times higher than the reported conductivities in the temperature range of 75 °C to 300 °C.

Jan 1, 2006

By G. A. Brooks

The problem of treating concentrates with increasingly higher levels of arsenic and antimony is compounded by the trend to stricter environmental guidelines regarding the disposal of smelter wastes. Much of the arsenic and antimony from non-ferrous processes is recovered as oxide fume. The options for handling these fumes include recycling them to the smelter, stabilising and disposing of them, and recovering values from them. Whilst arsenic oxide has little value, there is a market for antimony oxide and this provides an incentive for devising techniques for separating antimony oxide from arsenic oxide before disposal of the arsenic oxide. Arsenic can be separated from antimony oxide by selectively volatilising the more volatile arsenic trioxide from a mixed oxide sample or by selectively condensing the less volatile antimony tetroxide at high temperatures, leaving arsenic trioxide to condense out at lower temperatures. The results of selective volatilisation experiments at 379 to 587 °C indicate that it is difficult to achieve an arsenic content below 5.0 wt.% using air or nitrogen as carrier gas due to the formation of solid solutions between the two oxides. Injection of oxygen into a mixed vapor stream improved separation by selective condensation and antimony tetroxide containing as low as 0.23 wt.% was obtained in laboratory experiments.

Jan 1, 1994

By W. G. Davenport

Smelting oxidizes Cu-Fe-S concentrate to matte. Converting oxidizes this matte to metallic copper. Smelting and converting are, therefore, part of the same oxidation process. It would seem natural, then, that smelting and converting should be combined to produce metallic copper in one step. This would: (a) maximize S02 capture by restricting S02 emission to a single, continuous source (b) minimize industrial oxygen and fuel requirements (c) minimize cost. This chapter discusses one step, direct-to-copper flash smelting as it is practiced in 2000. It then uses. the matrices of this book to determine: (a) the industrial oxygen and oil requirements of direct-to copper flash smelting (b) the distribution of Cu between metal and slag during direct-to-copper flash smelting. It concludes that direct-to-copper flash smelting: (a) captures?S02 efficiently from its single continuous stream of SO2 off gas (b) minimizes oxygen/oil consumption but: (c) sends -114 of its Cu-in-feed to slag.

Jan 1, 2001

By Adam C. Powell

A new Cahn-Hilliard phase field model of transport-limited electrochemistry describes phase boundary motion due to oxidation and reduction reactions at metal-electrolyte interfaces. Benchmarks demonstrating the accuracy of the method include open circuit voltage and closed circuit current in metallothermic reduction, and linear stability theory in metal electrolysis, including a new stability criterion for reduction of liquid metal from liquid electrolyte. The model is applied here to understanding cathode interface stability in titanium electrolysis e.g. in the SOM process developed with Uday Pal, and to structure evolution in subhalide reduction of titanium dichloride by magnesium developed by Toru Okabe. Potential for application to new fuel cell and battery systems is also discussed.

Jan 1, 2006

By B. R. Adams

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and' surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By Ma Ying

The continuous directional solidification technique of five kinds of special ZA alloys with eutectic, peritectic and eutectoid transfonnation under the condition of continuous casting by heated mold was studied. The mechanism of surface defects appearing in ZA alloy line was discussed and the structure of some defects were analyzed by SEM. The results show that only when the fitting of various technique factors, pressure head, outlet temperature, pulling speed and cooling condition are reasonable under a certain range, can the ZA alloy smooth line be continuously pulled out. Unreasonable techniques will result in hot tear, rough surface, mush outlet, leaking and other defects. The shape and location of solid-liquid zone have an important influence on the formation of the above defects. When the solid-liquid zone is located in the mould outlet or inner mould, the surface of solidification will protrude into the inner mould. If the remaining liquid cannot counteract the solidification contraction, a rough surface will appear. If the solidification surface further into the mould, the ingot in the mould will have a great friction force when pulling and will form a hot tear. When the solid-liquid zone is moved out of mould, the solidification surface will turn into a plane, which easily results in leaking. A vibration or unstable operation will cause an ingot winding during pulling.

Jan 1, 2003

By Nobuhiro Oguma, Yuji Mizuta, Hideya Sato, Shigehiko Iwahori

"Recyclable materials containing copper and precious metals have been treated at the Mitsubishi Process in Naoshima. In 2003, a new incinerating and melting plant (pre-treatment plant) for waste materials, such as shredder residue of automobile and scrapped appliance, was constructed. All of produced slag/metal mixture is treated at the Mitsubishi Process, and which results in the significant increase of recyclable materials treatment. The combination of two processes has realized a highly efficient and environmentally friendly system for recycling valuable metals in the waste which used to be sent to a landfill. Naoshima continues to make efforts to achieve the highly efficient operations of the two processes, and plans to increase the treatment of recyclable materials further. This paper summarizes the recent operations and the various improvements implemented in the pre-treatment plant.IntroductionRecyclable materials containing valuable metals such as copper and precious metals have been treated at the Mitsubishi Continuous Copper Smelting and Converting Process (Mitsubishi Process) since the start-up in 1991. In the early stages, recyclable materials consisting mainly of metal scrap were charged into the process and the treatment had been increased steadily. In order to promote the recycling business, treatment of various kinds of materials including printed circuit boards was started. However, the treatment hit the ceiling due to a limitation of furnace boiler capacity, since they contained large amounts of combustible materials. In addition, severe corrosion of boiler tubes was caused by halogen contained in recyclable materials."

Jan 1, 2012

By M. Z. Quadir, M. A. Islam, P. J. Hazell, G. J. Appleby-Thomas, J. P. Escobedo

The mechanical response of closed-cell aluminium metallic foams subjected to low and high strain-rate loading has been investigated. A set of quasi-static and dynamic (shock) compressive tests have been conducted on closed-cell aluminium foams (CYMAT) with densities of 0.50 and 0.30 g/cc. Post-mortem characterization via optical microscopy and electron backscatter diffraction (EBSD) was performed on pristine and deformed specimens to elucidate the dominant deformation mechanisms in these materials. The combination of these techniques allowed for the assessment of critical deformation parameters such as changes in cell geometry and morphology, as well as microstructural evolution and deformation of the aluminium cellular network. These findings aim to aid in the design and development of optimized material structures for impact and blast protection.

Jan 1, 2015

By Sedef Pinar Basag, Onuralp Yucel, Ahmet Turan

Niederschlag process is commonly used to produce metallic antimony. The process is a metallothermic process which is conducted in one step for metallic antimony production. Using this method Sb2S3 is mixed with coal and metallic iron and subjected to reduction. During heating, antimony sulfide is decomposed and sulphur combines with iron to form the matte phase. Metallic antimony is collected at the bottom of the crucible. In this study, evaluation of Sb2S3 concentrate, extracted and obtained from West Anatolian Region of Turkey was investigated by using Niederschlag process. The reductant stoichiometry, reduction temperature and duration were carried out in the experiments. Chemical analysis methods by using atomic absorption spectrometry (AAS) and X-ray diffraction spectrometry (XRD) techniques were used for the characterization of the concentrate, metallic nuggets and matte phases.

Jan 1, 2016

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Darryl Lovato, Ramiro Pereyra, Daniel S. Schwartz

"During an annual inventory of nuclear material, a plated steel container which contained plutonium oxide failed. The container had been packaged for temporary storage but had been overlooked and remained in storage for more than 23 years. Although it was determined that the failure occurred through the slip-top rim, a metallurgical evaluation was requested to help to determine the integrity of the container.Optical metallography and scanning electron microscopy were used to analyze the character and degree of corrosion in the container. The depth of corrosion, measured at approximately 10 µm, did not pose a threat to the integrity of the container. However, the corrosion morphology and chemistry did suggest that a galvanic cell had developed between the tin and steel from the condensation of water. The morphology also suggests that the attack of the steel took place over a series of cycles due to changes of the environment.IntroductionMetallographic analysis was requested as part of the investigation into the mechanism of the failure of a slip-top container (#38621) containing plutonium oxide (PuO2) powder. The container had leaked during a special nuclear material (SNM) annual inventory causing contamination and closure of the vault. A photograph of the container and interior container is shown on the right in Figure 1. An initial investigation established that the source of contamination was the consequence of the failure of multiple layers of containment. Initially by the deterioration of the interior plastic bottle and polyvinyl chloride (PVC) bagout bag, and finally through the lid and steel container interface at a location where tape had not adhered properly [1]. Although the source of the breach was established, it was determined that metallographic analysis was important to establish the extent of deterioration of the steel container."

Jan 1, 2008

By Hee Dong Jang

Crystalline metal oxide nanoparticles such as lithium cobalt oxide (LiCoO2) and indium tin oxide (ITO) were synthesized from sprayed droplets of aqueous precursor solution by flame spray pyrolysis. Complete thermal decomposition of the aerosol precursors was obtained at high flame temperature. Molar concentrations of the precursor solution, and the flow rate of combustion gas such as hydrogen, oxygen and air were varied to control particle size, size distribution and crystal structure. The crystalline nanoparticles synthesized were nearly spherical, and their average primary particle diameters ranged from 11 to 35 nm for LiCoO2 and from 8 to 15 nm for ITO.

Jan 1, 2006

By R. G. Haire

Studies of the f-elements under pressure provide important insights into their solid state chemistry and physics. From such studies, of the elements and their alloys, it has been established that the normally localized f- electrons of several of these elements can become, involved in bonding under pressure. The electronic behavior of f-element compounds under pressure tend to be more difficult to interpret, due to the variety and the nature of electronic orbitals that are present. The 4f-elements and some 60% of the 5f-elements have been studied under The systematic comparisons that have been established for these materials are discussed.

Jan 1, 1992

By Bora Derin

The synthesis of titanium diboride (TiB2) by carbothermal reductions of TiO2 and B2O3 was investigated. For this aim, TiO2, B2O3 and carbon black powders were dried, weighed out and mixed in stoichiometric molar proportions (TiO2:B2O3:C = 1:1:5). The experiments were carried out in a graphite resistance furnace in argon media using different range of temperature (1400- 1700 °C) and time (0 and 15 min). The phase analyses observation of the products were examined by using XRD.

Jan 1, 2008

By Jan Petter Maehlen

Solid H-absorbing materials are in focus of ongoing R&D to offer viable solutions for the hydrogen storage and supply systems aimed on use of hydrogen as energy carrier for automotive transportation. Low operating pressures, combined with high gravimetric and volumetric efficiencies, together with fast kinetics of hydrogen release at ambient temperatures (providing conditions for a low energy loss due to decomposition), are the most important features of the ?ideal? H storage material. Hydrides of the light elements are the only possible candidates to build systems with an overall efficiency similar to those accommodating liquid or compressed (700 bar) hydrogen. One promising material from this point of view is aluminium trihydride, alane AlH3 with a gravimetric storage capacity of 10 wt.% H. This work was focused on studies of the crystal structure and thermal decomposition of alane by application of powder synchrotron X-Ray diffraction.

Jan 1, 2006

By John O. Burckle

For years, the measurement of fugitive emissions from the primary copper converter has defied all attempts based on inferential measurements, It has been concluded by virtually all investigators that the only dependable tech¬nique to measure these emissions would be to completely enclose an operating converter to permit the capture and measurement of all emissions. However, complete enclosure with a metal hood is difficult; many of the most serious fugitive emissions result during periods when the converter must be attended with crane-operated equipment. This approach would require either opening of the enclosure to permit the entry of large items of equipment or completely new methods for charging and tapping converters' The installation of the air curtain hooding system at ASARCO's Tacoma smelter has permitted a quantitative approach to the direct measurement of the fugitive for the first time. In this program, the fugitives captured by the air curtain were measured at a downstream sampling point in the exhaust side of the air curtain system during the various portions of the converter cycle. Emission factors were established for sulfur dioxide, filterable particulate (method 5), inhalable particulate, and selected trace elements.

Jan 1, 1983

By Keith M. Axler

This report addresses issues specific to the generation of hydrogen fluoride via reaction of calcium fluoride with sulfuric acid. This process has been established on a commercial scale and is under consideration for treatment of calcium fluoride residues from uranium processing. Magnesium fluoride slags are also available as a product of uranium processing. The technique of using sulfuric acid for the production of hydrogen fluoride from magnesium fluoride is also under consideration as a residue processing scheme. In the current study, thermodynamic modeling was used to investigate these chemical processing systems. The results presented herein reveal information relevant to the selection of processing temperatures and conditions. Details include predicted effects in system composition based on operating temperatures for both the calcium fluoride and the magnesium fluoride systems.

Jan 1, 1996

By Byung-Su Kim

The recovery of elemental sulfur from sulfur dioxide has important implications for coal- burning power plants and nonferrous metal smelters. The thermodynamic analyses showed calcium sulfide to be suitable for recovering elemental sulfur from sulfur dioxide. At the temperatures of 1023 to 1153 K under the sulfur dioxide partial pressures of 5.0 - 60.1 kPa, elemental sulfur from sulfur dioxide was recovered by its reaction with calcium sulfide. The kinetics of this reaction were measured at the same conditions using a thermogravimetric analysis technique. This reaction scheme would be attractive if the coproduct calcium sulfate can be reduced to regenerate calcium sulfide. This is the topic of another paper. At 1073 K under the sulfur dioxide partial pressure of 25.8 kPa, 48 % of the original calcium sulfide was converted to calcium sulfate in an hour. Under the same conditions, 55 % of the regenerated calcium sulfide were converted to calcium sulfate in an hour even after third regeneration.

Jan 1, 1999

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006

By Pinakin C. Chaubal

Today?s steel industry is in a vibrant and resurgent mode. This transformation has been in the making for some time now. Over the last few decades, the industry was steadily transforming itself into becoming a high tech industry. New technology was adopted, efficiencies were enhanced, lean manufacturing concepts were brought in and a strong customer focus was developed. Today?s mills employ sophisticated instrumentation, computerized monitoring, on-line smart systems etc. driving processes that are producing at rates of many tons/minute. All this is not possible without judiciously using the latest available technologies in various fields and developing a more sophisticated work force. Prof. Sohn has been a pioneer in driving the concept of process engineering in process metallurgy. In this paper the focus is on some aspects of process engineering ? primarily process modeling - as applied to iron and steelmaking processes. Examples are shown to demonstrate how problems have been addressed. Some thoughts on future directions are presented.

Jan 1, 2006