Search Documents

By T. L. Baum

External oxidation during in-line heat treatment of TRIP steels can cause problems for the subsequent coating process. This research aims to elucidate the kinetic rates of internal oxidation, external oxidation and decarburization and their interdependence under different gas atmospheres and temperatures. A rolled steel sample chemistry of 0.14 wt.% C, 1.8 wt% Mn, 0.6 wt.% Si and 1 wt.% Al is used as a case study. Thermogravimetric techniques are used to examine the net mass change in a sample during heat treatment and the results show an initial mass decrease and later an increase for particular partial pressures of H2O. SEM-EDS, optical microscopy and glancing-angle x-ray are used to quantify the microstructure. The cross-section of the samples have 4 distinct zones: (i) an external scale, rich in fayalite, (ii) an internally oxidized region with Al, Si and Mn oxides in an Fe matrix, (iii) a decarburized steel region, characterized by large ferrite grains and low carbon content, and (iv) a relatively unaffected steel core with a structure similar to the starting material.

Jan 1, 2006

By Erik Olsson, Gunilla Hyllander, Stefan Schuster, Lena Sundqvist Ökvist, Maria Lundgren, Michael Hensmann, Olavi Antila

"Residual materials from the integrated steel plant itself or other sources often contain valuable compounds of e.g. C and Fe. Dust and sludge have to be agglomerated to be able to recycle to the blast furnace (BF) via top-charging. By injection of the materials, preparation methods in terms of e.g. drying and/or screening only, can be used. Alternative carbon materials (ACM) in terms of BF dust and sludge have been successfully injected up to levels of 60 kg/tHM in the LK.AB Experimental Blast Furnace (LKAB EBF®). Efficiency in recovery of valuable compounds as well as the behavior of undesired elements have been evaluated and are discussed.IntroductionTraditionally, recycling of steel in-plant fines is made via the sinter plant and blast furnace route. Steel plants operating with 100% pellet as ferrous burden and have no sinter plant. There are limited areas for land fill and costs are caused for preparation of landfills and deposit fees. Very fine paniculate dusts or sludges cause decreased productivity and increased coke rate in the sinter plant, and therefore other ways for recycling must be considered. Injecting them into the BF could be an economically and technically feasible alternative. Additionally, as the materials contain valuable compounds of e.g. C and Fe."

Jan 1, 2012

By Thomas P. Battle

Ilmenite (iron titanate) is the source of over 90% of all the titanium produced in the world today. At some point during production of titanium dioxide or titanium metal the iron impurity must be removed. Too often it becomes a waste instead of a product. DuPont and MINPRO have developed a solid-state process which separates the iron and titanium components of ilmenite into different high-purity powders, which can be separated using conventional mineral processing techniques. The main reactor in this process is a unique high-temperature ball mill, where the iron segregates from the ilmenite lattice with the assistance of catalytic quantities of He\. The results of lab, pilot plant, theoretical, and scale-up studies are presented and discussed.

Jan 1, 1996

By Mahesh C. Meyer Jha

AMAX has developed a chloride refining process to produce pure nickel and cobalt metals from mixed sulfide .precipitates, Metal chloride solutions, generated in a hydrochloric acid leaching step and purified in a solvent extraction circuit, are converted to metal oxides .and HCI gas by pyrohydrolysis. A pilot plant consisting of a 30-inch diameter fluidized bed reactor and other ancillary units was designed, constructed, and operated for over one year. Process design was aimed at minimizing energy consumption, maximizing conversion efficiency, and achieving simplicity of operation and control. The operation provided valuable information on process scale up parameters, process control strategies, and materials of construction., Several process variables such as bed temperature, solution composition, solution feeding system, bed particle size distribution, and fines recycle system were investigated to determine their effects on process efficiency and the physical and chemical characteristics of the product.

Jan 1, 1985

By Claassen J. O.

The Zinc Corporation of South Africa Ltd. (Zincor) operates an integrated roast ? leach ? electrowinning circuit. The efficient removal and control of iron forms an integral part of the process. Zincor developed its own iron removal process (Zincor Process), which was recently shown to be unique with some similarities to the para-goethite iron removal process. Newly developed operating parameters for iron removal are in the process of being implemented. These include a change in the pH-profile and operating temperature, the recycling of seed material and the utilisation of an alternative neutralising agent to aid iron removal. Some of these actions, together with the implementation of a pre-neutralisation step, new filtration equipment and control systems in Zincor?s Residue Treatment Plant have significantly reduced zinc losses associated with iron in calcine and the iron residue produced. This enabled Zincor to take a step closer to world-class zinc recovery levels of around 96% for a similar type of operation.

Jan 1, 2003

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

By Chai Li-yuan

Anodizing behaviors of magnesium alloys AZ31 at constant applied current, based on the electrolyte solution free of chromate or fluoride, were investigated. The anodizing process was influenced by constituents of electrolyte greatly. Therein, the oxylate salts, which led to the occurrence of the two totally different processes, played a determinant role in anodizing. They were stable and sparking process respectively. The morphology of anodizing film was observed by SEM and the structure of film was analyzed by XRD. During the stable process, a brown thin film was formed, however the sparking process led to the formation of white hard thick film. The functions of some kinds of additives, such as ammonia, glyceryl alcohol and PVP etc were also studied. Some of them had great effect on surface morphology of anodic film and some of them affected stability of anodizing process significantly.

Jan 1, 2006

By Tapio Ahokainen

Commercial modeling software and increasingly efficient computers enable today computational fluid dynamics (CFD) to be used as a tool for a more comprehensive understanding of the flash smelting and flash converting processes. CFD modeling can be used for design purposes in many technological areas, but some relevant physical and chemical phenomena are still missing in the commercial CFD solver packages. Therefore, Outokumpu has developed several subroutines for solvers to describe analytically the phenomena in the flash smelting environment. CFD sub-models of the copper concentrate and matte combustion, the particle-particle-wall interactions and for more accurate radiation properties of the gas-particle suspension are needed to ensure reliability of numerical simulations on the flash smelting and converting vessels. Several basic combustion phenomena can be modeled with a number of commercial solver packages, but own models for combustion must be included in the case of sulfides as the feed. Mathematical models for copper concentrate and solid matte combustion have been developed during the last decade. They calculate compositions of the particles and temperature, based on extensive experimental research work in laboratory scale furnaces with validated kinetic parameters and temperature measurements of reacting particles. Inside and near the concentrate burner, the standard particle tracking methods do not include the particle-particle interactions and the particle-wall interaction is too much simplified to describe properly the particle collisions with the distribution cone. Therefore, additional models for the particle-particle as well as particle-wall interactions have been written and implemented. For thermal radiation, models for the emissivity of a gas mixture and for calculating the particle absorption and scattering coefficients have been developed and tested. In addition, the advanced radiation model can be used i.e. in the enhanced simulation of off-gas cooling in the heat recovery boiler area of the flash smelter.

Jan 1, 2006

By G. S. Rao

Levitated drops of Fe-18%Cr-2%C were reacted with oxygen-argon mixtures to study the reactions that occur in the AOD process, where the gases are injected into the melt and form bubbles. In the laboratory an argon-oxygen pulse, followed by pure argon, was flowed past the levitated drop to simulate the transient conditions in the gas phase as the bubbles rise in the melt. Oxide layers formed on the drops immediately when they came into contact with gas pulses containing 75% or more oxygen. Once the oxygen flow had ceased, the oxides reacted with the carbon in the drops to form CO gas and eventually disappeared. The de-carburization reaction occurred without oxide formation when the gas contained 50% oxygen or less. Melts that were sampled after EAF tapping, ready to be charged into the AOD, showed a higher tendency to oxide formation and consequent carbon boil than pure ternary Fe-18%Cr-2%C alloys made in the laboratory. The actual steel samples contained significant impurities, such as 0.25% Si and 0.56% Mn. A similar effect of oxide-forming impurities had been observed previously with binary Fe-C alloys. Movies were taken of the oxide formation and decomposition, and the results will be presented, along with data on the experimental conditions, including temperature and oxide compositions. The results are important because they give an insight into the reaction mechanisms in the AOD, which must be understood in order to improve and model the process.

Jan 1, 2006

By Jürgen Antrekowitsch, Thomas Griessacher

The recovery of valuable metals from residues like dusts and sludges is nowadays state of the art. Depending on the complex constitution, a recovery of different metals can – in the majority of cases – only be performed with considerable energy input in high temperature processes together with insufficient yields and newly generated residues. Often, the behavior of the dust or sludge in the process during melting or reduction is unknown. In this work, a detailed characterization of selected residues like steel mill filter dusts, cupola furnace dusts and leaching residues is done. The different steps of getting from solid particles into a homogenous liquid phase were investigated. Although high temperature processing leads to high reaction speeds, the complexity of residues keeps the system away from thermodynamic equilibrium. With this research program, some basics are generated to understand smelting and reduction and the gap between thermodynamical calculations and real behavior can be explained.

Jan 1, 2008

By Sung-Mo Jung

Experiments were carried out on a system with artificially prepared slags in a graphite crucible, in order to examine the possibility of recycling BOF slags produced in the steelmaking process. More than 80% of FeO and P2O5 was reduced within 20 minutes and the FeO reduction rate was greater than that of P2O5. P2O5 reduction began after more than 60% of FeO was reduced. Increasing slag basicity enhanced the reduction of FeO and P2O5. Temperature also improved slag reduction. The overall reduction rate was controlled by the chemical reaction at the slag/carbon interface. The reduction rates of FeO and P2O5 were second and first order with respect to their respective contents. Most of the reduced phosphorous is believed to vaporize in the form of P2 gas.

Jan 1, 2006

By C. A. Silva

Ladle change-over, during continuous casting of steel, initiates transient flow in the tundish which influences the inclusion content and degree of mixing between two consecutive batches of steel. The mixing behavior in the tundish during this period is determined by the casting rate and the ratios of: inflow to outflow during the refilling period; and, the low liquid level relative to the nominal level in the tundish during the transiency. A 3:10 scale water-model of a typical one strand slab caster was operated in conjunction with a tracer technique to characterize the velocity fields for several combinations of these parameters. Steady operation, a limiting case of the transiency, provided a basis for comparison. High-order moments -- skewness and kurtosis -- of the residence time density function have been utilized as signature elements associated with a particular residence-time distribution for the system. A simple mathematical model incorporating the above parameters as well as a characteristic Peclet Number was successful in simulating the features of the transient period.

Jan 1, 1993

By Eun Duck Park

The gold catalyst supported on iron oxide was prepared from gold dissolved in aqua regia by a deposition-precipitation method and applied to CO oxidation in the absence and presence of hydrogen. Some characterization methods such as X-ray diffraction (XRD), nitrogen adsorption, transmission electron microscopy (TEM), temperature programmed reduction (TPR), temperature programmed oxidation (TPO), and the pulsed CO chemisorption with temperature programmed desorption (TPD) were conducted to explain different catalytic activities of Au/Fe2O3 catalyst pretreated at different conditions. The particle size of gold was about 10 nm for Au/Fe2O3 calcined in air at 373 and 573 K. For complete CO oxidation, the decreasing CO conversion with a reaction time was observed at low temperatures but its initial catalytic activity can be restored by a heat treatment at high temperatures. This catalyst was quite active for the selective CO oxidation in the presence of hydrogen especially at low temperatures. In the presence of hydrogen, the deactivation was significantly diminished.

Jan 1, 2006

By G. T. Lapidus, O. J. Solis-Marcial

"The oxidative dissolution of copper from refractory minerals, such as chalcopynte, represents a technological challenge that has occupied hydrometallurgists for more than half a century. Innumerable processes have been suggested, but the majority operates at high temperatures or employs corrosive media. The origin of this refractory nature is the formation of passivating phases of iron(III) or copper. One option is to add non-corrosive ligands that complex these metal ions, thereby facilitating their dissolution. In the present work, the effect of acetone in sulfuric acid solutions was studied. The initial experiments were on chalcopynte carbon paste electrodes using cyclic voltammetry, where greater reactivity was observed. Later, leaching tests with hydrogen peroxide, cupric sulfate and ozone and, as oxidants, were performed. High extractions were achieved in three hours at 50°C. The solid residues contained the iron in the form of Fe203 and FeOOH.IntroductionChalcopyrite is the most important mineral of polysulfide copper ores [1] and accounts for approximately 70% of the world's copper reserves [2]. Currently, the copper present in chalcopyrite is extracted mainly by pyrometallurgical processes, which generate environmental concerns because of the formation of SO2 gas and submicron particulates [3]. The development of a less aggressive hydrometallurgical process for the extraction of copper would constitute a possible solution to these problems. For that reason, studies of the dissolution behavior of chalcopyrite are of great technological importance [4], However, the proposed oxidative leaching routes for chalcopyrite, generally at high pressures and temperatures, have not been implemented on an industrial scale, because of the elevated costs required to equal the high copper extractions obtained in thermal processes. These extreme leaching conditions are required because of the refractory nature of chalcopyrite. Passivation has been used to explain this phenomenon, although researchers have disagreed on the composition of the layer, which is various have assumed to be sulfur, copper sulfides, and iron-bearing jarosites or hydroxides [5]. If the latter compounds are the cause, an alternative solution would be the use of polar organic solvents in the oxidative leach to decrease the formation of the passivating iron layer. In this work, the influence of acetone on the oxidative leaching of a chalcopyrite concentrate at room conditions is explored."

Jan 1, 2012

By Wang Yun-yan

In order to examine the adaptability and the kinetics of leaching different gold ores in alkaline thiourea system, six kinds of gold concentrate and/or calcine with different physical and chemical properties were chosen as objects. The leaching behaviors in alkaline thiourea system with high stability, acidic thiourea system and alkaline cyanide system were compared. Changes of phase, surface appearance, particle distribution and specific surface area of six kinds of gold ores before and after leaching were studied in virtue of modern analytic techniques, e.g., XRD, SEM, and so on. The results indicate that alkaline thiourea solution can be used to leach gold ore, for oxidized gold concentrate removed arsenic by microbe pretreatment(4#) the leaching rate of gold is up to 82.68%, such conclusion overthrows the parlance reported that pH value must be less than 1.78, or gold can not dissolve in thiourea solution. Chemical components and phase are related to gold leaching rate, different gold ores are fit for different leaching system, and alkaline thiourea solution is suitable for the pretreated oxidized gold ores with low content of sulfur and in which the main phase was SiO2, phase almost does not change after leaching basically. Generally speaking, when leaching in alkaline thiourea solution, surfaces of gold ores with glaze change greatly to ones with coarseness, distinct trace and holes of corrosion. Particle size decrease and specific surface area increase of gold ores after leaching in alkaline thiourea solution with high stability except gold concentrate of Zhongyuan gold smelter(5#).

Jan 1, 2006

By C. E. M. Meskers, U. Boin

"The increasing use of coated magnesium in consumer products results in creation of coated Mg scrap during product manufacture and after End-of-Life product treatment. Currently this material is generally not recycled, leaving a material resource unused. Closure of the magnesium cycle in a sustainable manner is necessary. In order to do so, the effect of coatings on the recycling process has to be quantified, predicted and minimized. For this purpose metrics have been developed, based on first principles supported by detailed understanding of the recycling process. The developed 3D metric enables quantitative assessment of the recyclability and links coating design, product design and recycling to each other in a visual manner. The parameters that form the metric can be measured and predicted, hence an engineering basis for Design for Sustainability of coated magnesium is provided.IntroductionEvery product progresses through the four phases of the product life cycle depicted by figure 1. In each phase residues are created. Their amount and composition is largely determined by the complex material combinations created/invented during product design in the manufacture phase. Compared to the ideal cycle the magnesium cycle is far from closed (fig. 2). Most noticeable is absence of the link between the EoL phase and raw materials production. A closed cycle only exists for class 1 scrap, which goes from the product manufacture phase directly to production from industrial material and returns to the manufacture phase as magnesium alloys. The four problematic streams are marked by ???. Coated semi-products are present in two of the four residues, namely in rejects and collected scrap. When these semi-products are recycled the amount and composition of the dross and salt slag residue is affected as well.During product design selection of the coating takes place, fixing the coating character¬istics and properties from this moment on for the rest of its life cycle. The choices made in the manufacturing phase are therefore critically linked to the recyclability of coated semi-products as well as the sustainability of the magnesium cycle as a whole. Sustainable closed life cycles, in which the quality of materials is preserved and residue creation and resource depletion are minimized, can be attained by selecting the appropriate alternative during product design. To realize this the effect of design choices on the life cycle and more specific the recycling process has to be known and quantified."

Jan 1, 2008

By Akira Yazawa

Oxidic dissolution loss of metal in slag is discussed thermodynamically in terms of oxygen potential, activity coefficient and equilibrium constant. To understand basic principle, regular solution model is applied for model calculation of the activity behaviour of metal oxide in FeO-SiO2-CaO slag, and effects of slag composition, temperature, and basicity of oxide on dissolution loss are demonstrated. As: a simplified but practical conclusion, the dissolved metal loss in slag is inversely proportional to activity coefficient of metal oxide, and also to FeO content in slag when amount of slag is taken account.

Jan 1, 1994

By Aurelian Buzaianu, Cristian-Aurelian Popescu, Gabriela Popescu, Petru Moldovan

"A lot of scraps result in processing of composite materials which contain metallic phases that can be recovered and used again in different field. Considering this point of view the aim of the paper was to separate and recover aluminum from aluminum matrix/graphite composites. The separation and recovery of aluminum alloy from aluminum alloy/graphite composites was done by treatment with halide molten salts. As halide salts were used flux tablets that collect the ceramic particles in dross. After dross separation, was used filtration in order to separate the aluminum matrix from the other impurities.Samples from the recovered alloy were analyzed using chemical analysis, optical and electron microscopy, as well as X-ray diffraction. The desired composition of the aluminum alloy obtained from scraps could be reached by some addition of metals to the metallic phase. From optical microscopy it was obvious that the structure of the aluminum alloy obtained after composite reclamation consists large particle of silicon, eutectic, a-Al solid solution and other phases like Fe, Si, Mg and Ni, or some compounds like CuAl2. 1. IntroductionThe research on the recycling and reclamation of metal-matrix composites (MMCs) becomes active to preserve the natural environment, as environmental requirements become stricter, to save energy, and to reduce garbage. In case of recycled aluminum alloy ingot the production energy is about 3 pct of that of the new ingot. This evidence strongly supports the necessity to recycling of aluminum alloys. Among aluminum alloys, metal matrix composites have high strength and elastic modulus, and also good were resistance. These materials have been developed to meet the demand properties which exceeds that of the ordinary materials, and to save energy."

Jan 1, 2008

By Ker-Chang Hsieh

Four three-phase equilibria and one two-phase equilibrium in the FeNi- S-0 quaternary system in the vicinity of 1023 K and Pso2 = 1 atm were studied using the following emf cell 2 Pt,o2 (air)Zr02 .CaO/Pso2 = 1 atm, mixture of phases, Au The four three-phase equilibria are sp + (Fe,Ni )S + Ni 3s2, sp + Ni 3s2 + NiO, sp + NiO + N1S04 and Fe2 o3 + sp + (Fe,NOS04 -Y:he two-phase equilibrium is sp + (Fe,Ni)S. The two-.phase equilibrium was measured by using mixtures containing a major portion of one phase and a minor portion of the other. The results are presented in terms of oxygen potential as a function of YNi = nNi/(nN1+nFe) at constant temperature and pso2 = 1 atm. The stability diagram was also calculated using appropriate thermodynamic models for all the pertinent phases. The calculated diagram is in accord with the measured ones.

Jan 1, 1985

By John Petersen

Heap bioleaching technology has become well established for the exploitation of copper sulfide ores. Still, in many operations the rate of copper extraction is rather slow, often taking two years or more to recover 80% of the copper. Chalcocite, the most common secondary copper sulfide, leaches by a two-stage mechanism. The first stage is rapid, whereas the second stage has a high activation energy and proceeds slowly at ambient temperatures. Nonetheless, this rate is still considerably faster than what is typically realized in a full-scale heap. A comprehensive column bioleaching study of a chalcocite ore has shown that the chalcocite columns are leached in a zone-wise fashion. The first zone corresponds to the first stage of chalcocite leaching, where all ferric produced by the bacteria is immediately consumed and all acid entering with the feed solution is consumed within a relatively narrow band. The second stage of chalcocite leaching proceeds much more slowly in the wake of the first stage, within a zone that grows gradually over the entire length of the column. The overall rate of leaching is thus determined by the rate of acid supply into the column rather than by mineral or bacterial kinetics, at least until the entire column is engaged in second-stage chalcocite leaching. In full scale heaps, there is evidence to suggest that solution distribution favours channelling between relatively large clusters of material which are exposed only to stagnant solution. Reagents have to migrate into such clusters by diffusion, which retards the delivery of acid dramatically. Thus, we believe that the rate of chalcocite oxidation in heaps is governed by sideways diffusion rather than downward migration. Column experimental results have been reproduced with a comprehensive heap-modelling tool. The model predicts that by simply changing the length of the average diffusion channel from column conditions (a few cm) to heap conditions (tens of cm), extraction times can change from weeks to years under otherwise identical conditions.

Jan 1, 2003