Search Documents

By Axel Preusse

This paper shows basic considerations about the prognosis and prediction of surface subsidence and other ground movements in the German hardcoal industry. The following case studies describe experiences collected in projects between university and industry.

Jan 1, 2000

By Robert P. Kudlawiec

The use of Mobile Roof Supports (MRS) in pillar retreat mining has been a fairly recent occurrence in coal mining operations in the United States (1988). Determining the pillar block configuration, the crosscut and entry centers, the number of entries developed, the method of ventilation, and the type and mixture of equipment used arc all factors in establishing a successful pillar retreat operation. This paper will evaluate and report on the history of one coal company's relationship with MRS usage for pillar retreat mining and focus on the company's use of horizontal pillars (inverted-blocks) for the panel configuration.

Jan 1, 2000

By S. Mehrdad Heidari

The concentrator plant is located near a very high (105m), large (- 500m) and steep (a, > 45' ) wall. Geologically, the wall was composed of very complicated formations and broad range of soils and rocks type in which a variety of local typical failures models have been occurred on different soil and rocks formations. The construction of concentrator plant structure and other activities have been overshadowed by these local failures. Safety and risk of huge failures were serious concern. For distinguishing the wall conditions a broad campaign of slope stability investigation with detailed geotechnical drilling on berms of wall have been done and the structure of slope was fully identified and further Lab tests and slope simulation models done. Slope stability of the wall was analyzed and the effects of instability factors were described in short term (for construction phase) and long term (for production phase).The results indicated, if a well-appointed drainage system is implemented, the overall stability of the wall in short term will not cause any particular problem but about long term stability, the wall must be supported by rock bolting, consolidation grouting, shotcrete reinforced with fibers. The results have been confirmed by passing one year after this investigation.

Jan 1, 2005

By Bruce Hebblewhite, Jim Galvin

"A coal burst occurred on 15 April, 2014 at the Austar Coal Mine, located west of Newcastle, NSW, Australia. The burst resulted in fatal injuries to two men working as part of the mining crew at the development face. At the time, a continuous miner was being used to mine a longwall development gate road through heavily structured coal, at a depth of approximately 550m. A number of pre-cursor bumps had occurred on previous shifts, emanating from the coal ribs of the roadway, in proximity to the coal face.This paper reviews the geological, geotechnical and mining conditions and circumstances leading up to the coal burst event; and presents and discusses the available evidence and possible interpretations relating to the geomechanical behaviour mechanisms that may have been critical factors in this incident. The paper also discusses some key technical and operational considerations of ground support systems and mining practices and strategies needed for operating in such conditions in the future.INTRODUCTIONAustar Coal Mine is an underground longwall coal mine located near Cessnock in the Hunter Valley of New South Wales (NSW), Australia and is the only underground mine still extracting the Greta Seam in this region. The mine was the first in Australia to adopt the Chinese-developed Longwall Top Coal Caving (LTCC) method for thick seam extraction. Typically seam thickness ranges from 4m to 7m and depth of mining from 480m to 560m, with future mining planned down to depths of up to 700m, making it one of the deepest operating coal mines in Australia.On 15 April 2014, a pressure burst occurred in the left hand rib at the active mining face of B Heading, 2 to 3 cut-through, Maingate A9 panel, during development of the gateroads for the ninth longwall top coal caving panel. Strata in the general vicinity was affected by disturbed geology and multiple geological structures. Figure 1 shows a section of the mine plan as at October 2014 (six months after the accident), indicating the current longwall extraction panel (AS) and the development panel A9 where the accident occurred. (Note: Neither development nor longwall face positions changed significantly between the time of the accident and the date of this plan). At the time of the accident the current longwall face was in excess of 1,000m away from the Maingate A9 development panel face position."

Jan 1, 2016

By Yvette Heritage

"The risk of fatalities from rib failure is still prevalent in the coal mining industry. This risk has prompted further research to be conducted on rib deformation in order to understand the mechanisms of rib failure, with the long-term objective being to improve rib support design. This paper presents the results of ACARP research project C25057, which investigated the mechanics and drivers of rib failure. The results of rib deformation monitoring at three different mines in Australia provides rib deformation characteristics for overburden depths ranging from 160 m to 530 m. Monitoring includes deformation during development drivage conditions and during the longwall retreat abutment stress environment. The rib deformation monitoring covered three different seams: the Goonyella Middle Seam, Ulan Seam, and Bulli Seam in the Bowen Basin, Western Coalfield, and Southern Coalfield, respectively. The observed mechanisms driving the rib deformation ranged from bedding shear failure along weak claystone bands to vertical shear fractures to kinematic failures driven by shear failure dilation. The variation in mechanisms of rib failure, together with the seemingly consistent method of rib support design, prompts the question: What exactly is the role of rib support?INTRODUCTIONThe current risk of rib fatalities in the coal mining industry has prompted further research into understanding the mechanisms of rib failure. Three Australian mines assisted further research by providing sites for rib deformation studies as part of the Australian Coal Association Research Program (ACARP) project C25057. The mines included in this study were Moranbah North Mine, Ulan West Mine, and Appin Mine. This paper provides key results of the rib deformation monitoring relevant to assessing the mechanisms of rib deformation.The approach of monitoring rib deformation and rib support loads was used to measure and characterise the dynamic rib deformation present in both development and longwall retreat stress environments. The characterisation of rib deformation, together with rock failure modelling, was used to determine the mechanisms for failure within the rib and to assess the interaction of rib support with the failure process. The mechanisms of rock failure are considered an important factor in understanding the drivers for the failure. Consideration of the site-specific failure mechanisms can provide for a more tailored support design."

Jan 1, 2018

By Bob Coutts, Matt Martin, Dan Lynch, Dan Payne

"The Broadmeadow punch longwall coal mine in Central Queensland Australia has experienced significant highwall movement associated with the effect of longwall subsidence when the longwalls approach their final position close to the open-cut highwall. In response to this movement, Broadmeadow employed two types of broadscale highwall monitoring (radar and laser scanners) to provide full coverage measurement throughout three consecutive longwalls approaching the highwall. This was to attain a better understanding of the mechanism causing the movement and potentially enable prediction of instability. Results from the monitoring found the highwall is displaced to magnitudes unlike those typically measured in open-cut mining and in direct contrast with typical longwall subsidence behaviour.This paper discusses the ground movements measured, monitoring methods used, safety measures established, as well as theorising the failure mechanism. Recommendations are made for mine and pit designs for future punch longwall layouts. The paper shows how the movements measured are more aligned to some measurements made during stream valley closure studies previously presented at the ICGCM and challenge the mechanisms suggested by previous literature.BACKGROUNDThe mining of longwalls under or adjacent to large voids (e.g., stream valleys, escarpments, or cliffs) is commonly associated with heavily vegetated or steep surface areas. In areas of extreme topographic variance, access to traditional survey pegs and stations or even new radar or laser technologies is limited. In addition, seldom have the longwall layouts aligned themselves parallel or perpendicular to the surface feature, making interpretation of any available surface movement data more complicated.The punch longwall layout (Figure 1) is also quite uncommon (only undertaken at a small number of longwall mines in Australia) but creates the perfect configuration to enable a somewhat controlled study of the effect of longwall subsidence on a steeply dipping surface feature (an un-vegetated, evenly excavated open-cut highwall). The relatively recently developed radar and laser scanning technology has also enabled near continuous, real-time, sub-millimetre monitoring of a full 500m wide x 100m high highwall. Because the punch longwall enables access and a clear view, the technology could be easily deployed as compared to the highly vegetated and variable topography of stream valleys."

Jan 1, 2018

By Bruce K. Hebblewhite

BHP Billiton Illawarra Coal operates Dendrobium Mine in an area 10-20km west-northwest of Wollongong in the Southern Coalfield of New South Wales, Australia. The mine recently completed longwall mining in Area 3A adjacent to an overhanging rock feature known as Sandy Creek Waterfall, which had been identified as a significant, and potentially sensitive natural surface feature of the environment. This waterfall lies within the Sydney drinking water catchment area, in a surface terrain of variable topography where non-conventional subsidence behaviour such as valley closure, and far-field horizontal movements are known to occur, over and above conventional subsidence responses to mining. As a part of the conditions of approval to mine, Illawarra Coal undertook to protect the waterfall and the section of Sandy Creek immediately upstream of the waterfall from the effects of longwall mining using an innovative management process and an array of very high resolution monitoring systems. This paper outlines the type of non-conventional subsidence effects that can occur; the range of different monitoring regimes adopted in response to such effects in order to develop an understanding of the valley closure phenomenon in proximity to the waterfall and provide suitable early warning data. The paper also describes the management processes that were adopted, incorporating the use of these monitoring regimes in order to successfully protect the waterfall from the valley closure effects of mining four adjacent longwall panels in close proximity to the waterfall while continuing to maximise recovery of the coal resource in the area. The management structure adopted involved a technical committee, a steering committee, and an external independent reviewer. The technical committee was responsible for design of the monitoring systems, interpretation of the results, and making timely recommendations to the company steering committee who were then able to make informed decisions on when to cease mining each adjacent panel. The steering committee comprised Illawarra Coal management and technical personnel. Although the steering committee took advice from the technical committee, all decisions relating to mining were made by the steering committee. An external reviewer was engaged by the steering committee at the end of each longwall panel to review the results, interpretation and management decisions. This management structure was effective in successfully protecting the very sensitive structure of Sandy Creek Waterfall from potential impacts of nearby mining in the midst of active ongoing natural erosion processes.

Jan 1, 2014

By Joe E. Bryan, John P. McDonnell

"Underground mine rib stability is an ongoing safety issue in all mining applications. Rib-related accidents present at least as many problems as roof-related ground control. Underground coal mine rib safety is continually emphasized as a primary safety concern at every mining operation. The application of rib support materials is increasing as more difficult mining conditions are experienced due to deeper cover, more variable depositional environments, thicker seam heights, and multi-seam mining effects. As the coal seams become thicker, the need for rib control increases. A variety of rib control methodologies has been documented and research continues on mine design methods and support techniques to reduce or eliminate rib-related accidents.This paper presents an alternative rib bolting technology using proven conventional rib support systems that allows mine personnel to more efficiently install rib support during development operations. This alternative rib bolting method allows for additional rib support with a single support installation.INTRODUCTIONRib control continues to garner the watchful eye of both concerned operators and government officials due to many factors: inherent safety within entries and crosscuts, actual rib stability history, safety improvement, cost control, improved mining methods, and maintaining production goals. As demonstrated through many years of actual practice, desired outcomes can be achieved by scrutiny, innovation, and combining improved practice methodologies.Rib surface control continues to be a necessary part of the production process. However, production and safety issues persist at the point of installation using current control apparatuses and methods to install rib controls. Among others, current issues of rib control are quantity of bolts required, overall time required for installation, ease of apparatus installation, flexibility of the system for appendage installation and operator exposure. A need exists to decrease the time miners spend installing rib control apparatuses, while increasing the safety of such installation processes. At present, installing rib control devices (primary rib bolts, plates, mesh, and, in most cases, secondary rib bolts and plates) is performed in a very congested area and is time-consuming process at the primary coal-winning area: the face. The MatLok system addresses these problems."

Jan 1, 2015

By Peter Zhang, Todd Minoski, Mark Van Dyke, Daniel W. H. Su

"This paper presents the results of a 2017 study conducted by the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Mining Research Division (PMRD), to evaluate the effects of longwall-induced subsurface deformations within a longwall abutment pillar under deep cover. The 2017 study was conducted in a southwestern Pennsylvania coal mine, which extracts 1,500-foot-wide longwall panels under 1,185 feet of cover. One 650-foot-deep, in-place inclinometer monitoring well was drilled and installed over a 150-foot by 275-foot center abutment pillar. In addition to the monitoring well, surface subsidence measurements and underground coal pillar pressure measurements were conducted as the 1,500-foot-wide longwall panel on the south side of the abutment pillar was being mined.Prior to the first longwall excavation, a number of simulations using FLAC3D™ (Itasca, 2017) were conducted to estimate surface subsidence, increases in underground coal pillar pressure, and subsurface horizontal displacements in the monitoring well. Comparisons of the pre-mining FLAC3D simulation results and the surface, subsurface, and underground instrumentation results show that the measured in-place inclinometer casing deformations are in reasonable agreement with those predicted by the 3D finite difference models. The measured surface subsidence and pillar pressure are in excellent agreement with those predicted by the 3D models. Results from this 2017 research clearly indicate that, under deep cover, the measured horizontal displacements within the abutment pillar are approximately one order of magnitude smaller than those measured in a 2014 study under medium cover.INTRODUCTIONDue to a recent shale gas boom, approximately 1,400 unconventional shale gas wells have been drilled through active and future coal reserves in Pennsylvania, West Virginia, and Ohio over the past 15 years. These shale gas wells have penetrated many coal seams, such as the Sewickley, Pittsburgh, Upper Freeport, and Kittanning seams. These unconventional gas wells, whether tapped into the Marcellus or Utica formations, contain very high gas pressure. Strata deformations associated with longwall and other high extraction techniques could induce high stresses and deformations in the shale gas well casings. This could seriously compromise the mechanical integrity of the production, intermediate, and coal protection casings (Figure 1). Damaged well casings could potentially introduce high-pressure, explosive gas into underground mine workings, particularly during an extended well shut-in period, which could seriously jeopardize underground miners’ safety and health."

Jan 1, 2018

By Donald P. Richards

West Elk Coal Company operates its Mt. Gunnison No. I mine on the western slope of the Rocky Mountains in Western Colorado. The mine is located along the north fork of the Gunnisson River near Somerset, Colorado as shown in Figure 1. The mine is designed for a sustained production of 1.4 million tons per year out of the "F" coal seam in the Mesa Verde formation. The coal seam is nominally 7 feet in thickness and dips at about 3 ½ degrees to the northeast. Mining of the seam is up dip with the entry portals on the north facing slope of Mount Gunnison. The mine is designed as a five entry system with four entries for ventilation and access and one entry for a coal-handling conveyor. The mine entry layout is shown in Figure 2. Initial mine planning began in 1979, with "permitting" complete and construction starting in the fall of 1981. A "turnkey" contract for design and construction of all five parallel mine entry tunnels was awarded by West Elk Coal Company to a Joint Venture of Jenny Engineering Corporation (design and contract management responsibility) and Affholder, Inc. (construction responsibility). The first entry access into the coal seam was completed in the early spring of 1982. The mine has been operating at full service (all five entries) for nearly 3 years.

Jan 1, 1984

By G. Skybey

The Skybolt is a new bolt concept, point anchored with resin in large diameter holes of specific sizes 38 mm and 45 mm. The new design achieves the optimum annular spacing required for mixing the resin anchor components which is essential for optimum resin bonding of the bolt to the surrounding rock. This paper explains the load transfer mechanisms between bolt/resin/rock, unique to this bolt concept. It compares the pull-out test results to those of paddle and expansion shell type bolts, and highlights the versatility of Skybolt over existing, currently used, rock support systems and the benefits mine operators can achieve when using the Skybolt.

Jan 1, 1992

By Frank Schmidt

Due to changing geology, rib bolting is an ever-changing problem in ground control. With the economic status of the coal market, the need for safely increasing productivity in rib bolting is at an all-time high. The current solutions used in the market often require a long installation time (e.g. if collapsed holes have to be redrilled) or result in poor quality installations that can lead to insufficient ground control. A new bolting product based on the simple screw principle has been developed to bolt ribs faster and with a more repeatable, higher level of installation quality. The paper covers the product invention and development, the fastening principle and its advantages over current systems and first experiences in the market. The first underground trials have shown that the screw anchors can be installed safely and efficiently, often faster than traditional methods. The screw anchor does not suffer from conventional bolting issues such as collapsed holes due to bad ribs. The screw anchors are designed to obtain steel failure and load testing underground shows consistent fastening in all types of conditions.

Jan 1, 2013

By Saeed Zhandi, Behdeen Oraee

"Rock bursts remain an important problem in longwall coal mining. These bursts are due to a sudden and severe failure of rocks from a high stress concentration in deep underground excavations that occur with the instantaneous release of strain energy stored in the rocks. They can potentially cause irrecoverable damage to equipment and personnel, thus accurate rock burst prediction and control is expected to be carried out by the mine design engineer. As a result, this can constitute major challenges for said engineer. In this paper, forensic engineering has been used to evaluate the possibility and extent of rock bursts in deep coal mining. For this purpose, established mining engineering principles, including factors influencing the severity of rock bursts, have been incorporated in the forensic engineering technique. The analyses took place in five steps:• Assessment of regional and local conditions prior to the event• Assessment of conditions after the event• Hypothesize plausible ways in which pre-event conditions can become post-event ones• Search for evidence that either denies or supports various hypotheses• Apply engineering knowledge to relate the various facts and evidence into a cohesive scenario of how the event may have occurred.The paper concludes by demonstrating a method for predicting rock bursts and preventing their reoccurrence. The methodology used in this paper, together with the results obtained, can serve as useful tools for the coal mine design engineer in the primary evaluation of rock burst potential in underground coal mines.INTRODUCTIONA rock burst is defined as the sudden and great failure of rocks due to a high stress concentration in deep underground mines. This phenomenon occurs with the instantaneous release of strain energy that is stored in the rocks, and can cause irrecoverable damages to both equipment and personnel (see Figure 1). Rock bursts pose a hazard owing to their lake of predictability; in fact, research into understanding rock burst mechanics and implementing techniques for their monitoring and prediction has been taking place for over 50 years."

Jan 1, 2015

By Don Berger

Highwall scaling, bolting and technical blasting are important aspects in the remediation of existing highwall exposures. Proper planning, design and research are important first steps in the development of long term stability. Research into old workings and their influence on highwall stability control the planning and design. These steps are followed by improvements in blasting techniques, highwall monitoring programs and constant evaluation of the results. Recently, due to a number of factors, the highwalls of the Open Cut Mine have started to deteriorate, creating both operational and potential safety problems. Geologic setting, highwall design, mining operations, old workings and weather have combined to create adverse conditions that have allowed sections of the highwalls to become unstable. Homestake Mining Company has developed a program to alleviate the existing ground control problems and to decrease the effect operations has on future highwall stability.

Jan 1, 1996

By Graham Daws

The introduction of UK rock bolting technology has been applied in many large underground coal mines around the world. This paper explains the methods that have been applied for its successful introduction and discusses several case studies. It does not give fine detail but is intended to allow decision makers to gain a basic understanding of the method used to introduce rock bolting to a mine.

Jan 1, 2011

By Marcel0 Mondring

Transportation and the logistic requirements are set very high for the German coal mining industry. Short transportation resources, crowded quarters, and long transportation distances to destinations are some basic conditions that logistic employees of the mines have to deal with. Therefore, in the context of these processes, human effort and technology are faced with great challenges. There can be a total of 300 transport units, depending on the size of the mine. Every day, they are moved through a nearby 150-km-long transportation network of floor and monorail tracks. Of these transport units, 150 are new, and the other 150 units are split into cross traffic units that are moved only in the underground and return travel units. Beside track-bounded transports, all material transports take place in the shaft. As a result, many involuntary transports and changes in the means of transportation make the daily work more difficult. Typical transports in the shaft include the supply of new materials from above to below, as well as returnable goods from below to above. Cross traffics throughout several levels, which are rather rare, would have to be handled above the shaft. Due to limited shaft capacity, these cross traffics should be avoided when possible. Based on the gas resources in coalmine slopes, track-bounded transports using monorails (powered by diesel or rechargeable means) are preferred. This depends on the road degree, the depth, and track cross section of the shaft/slope. The variety of the material spectrum includes more than 100,000 different types of material.

Jan 1, 2014

By André C. Zingano

The domino effect in a violent pillar collapse occurs due to the redistribution of stress in the remaining pillars near the collapse, and this stress transfer occurs in the immediate and main roofs. The remaining pillars do not have enough load capacity to support this overstress and also fail, and the domino effect propagates further to the entire panel. The domino effect does not occur only due to low load capacity of the pillars, but also the roof rock mass quality, because the stress is transferred by the roof. In high competent roof without discontinuity (fault), like massive sandstone seam, the deformation of the roof is the cause of pillar collapse extension and propagation. Depending on how close it is approaching the collapse limit; the immediate and main roofs behave differently. When it is close to the collapse limit roof convergence and pillars compression occur. Conversely when it is far from the collapse limit divergence and pillars decompression occur. This is called the arc-effect. This paper studies this behavior of the roof (immediate and main roofs) using numerical modeling to simulate the roof deformation and stress distribution in the roof and pillars. This simulation represents the progression of pillar collapse and shows the zone of convergence and divergence of the roof, and also the effect of this behavior on pillar confinement. Two-dimensional plain strain model was applied to simulate the arc-effect. The simulation results were compared to those of the instrumentation that was installed before the collapse. Keywords: pillar collapse, room and pillar, numerical modeling

Jan 1, 2005

By Wenjun Ju

It's very important to determine the limitation of bed separation in entry roof in order to predict roofs stability and take some necessary precautions. Based on numerical modeling and monitoring in the field, the new concept of Limitation of Roof Layer Separation (LRLS) and its method of determination LRLS is given in this paper

Jan 1, 2001

By A. Bortolussi

The paper discusses the state of the progress reached in the development of the diamond wire tool for cutting hard rocks. To the advances of this relatively new technology a substantial contribution has been provided by the research being carried out at the University of Cagliari on samples of granite rocks from different Sardinian stone quarries. On the basis of field experiments and laboratory test data, the mechanism of diamond wire cutting has been assessed. In particular the influence of the rock features and operational variables an tool performance (cutting rate and bead wear) has been elucidated.

Jan 1, 1992

By Kot F. v. Unrug

In spite of the extensive research and accumulated experience from mining operations, an appropriate pillar design remains an open issue. Due to the shrinking reserve base, present mining operations move to more challenging conditions. There are usually thinner seams and geologic conditions are often unfavorable. For instance, mine roof and floor are weak or deteriorate rapidly when exposed to moisture fluctuations in mine atmosphere. It is common that pillars of current operations are more- squat than several decades ago when the bulk of pillar research have been carried out in thicker seams. The methods of pillars calculations were developed regionally (in particular countries) to suit design needs for the most important seams, from which the majority of coal production was coming (e.g. Pittsburg or Pond Creek seams in the eastern of US). Most of the pillar formulae use similar approach by assigning weights (using constants) to the influence of coal (seam) strength and pillar widthheight ratio on its final strength. That mechanistic approach has sound theoretical base and good data supporting its validity. However, what seems to be missing is a qualification system of the mine conditions, which are outside of the data base or do not comply with the theoretical model applied in pillar strength formulae. This paper attempts to address that issue in two major categories, first when only a drill core data are available, and second during the mine development observations can be made directly on a coal seam. The composition of a coal seam is also addressed, (which often changes rapidly across the reserve), and discussed its influence on pillar's structural performance. In summary a set of practical design rules is presented.

Jan 1, 2005