Search Documents

By Ehsan Alavi, Brian Hagan, Glen Frank, Michael A. DiPonio, Michael Mooney, Lisa Mori

"The data from EPB cells located inside the pressurized chamber of EPB TBMs and also the data from the pressure sensors in grout lines are quite important in controlling the EPB operation. However, there have always been questions in regards to pressure distribution along the shield body. Could the pressure distribution data be used to come up with potential locations for ground loss? Does the overcut region, the space between the shield body and the maximum cut diameter, consist of broken material or EPB muck, or does that region consist primarily of void space? During free air interventions, how does pressure distribute along the TBM body? To address these questions, one of the two EPB TBMs used in the Northgate Link Light Rail project in Seattle, WA is equipped with EPB cells in front and rear body to monitor the pressure distribution along the TBM body in addition to the standard 6 EPB cells located inside the cutterhead chamber and pressure sensors located at the grout lines. This paper discusses the results of this study and weighs on the valuable data that can be collected by using the shield pressure sensors.INTRODUCTIONThe cutterhead of the TBM is normally equipped with overcutters on the cutterhead periphery which extend into the annular space beyond the diameter of the TBM shield. Thus, the overcutters serve to disturb and excavate some of the ground in the annular space which reduces friction and resistance around the TBM body. This phenomenon is necessary to help the TBM steer and navigate around curves. Additionally, the shield of an EPB TBM is also often shaped like a cone, with the diameter decreasing from the front to the tail shield. This conical shape also helps the TBM to navigate because material that is cut by the cutterhead either gets pulled into the cutterhead or it gets pushed out of the way – around the cutterhead and into the annular space. In EPB tunneling, the conditioned material from the face that does not get pulled into the cutterhead mixing chamber flows into the shield gap and pressurizes the surrounding ground. Additionally, grout can travel from the segment annulus into the shield gap. The pressure in the shield gap mainly depends on the pressure of the material at the face and the grouting pressure behind the tail shield."

Jan 1, 2016

By Yiming Sun, David Tsztoo, Rick Nolting, Adam M. Wirthlin, Rebecca Fusee

"Excavation and initial support of the New Irvington Tunnel presented significant challenges, including rapidly changing ground conditions, heavy ground loads, and squeezing. Such behaviors were anticipated from historic tunneling records of the adjacent Existing Irvington Tunnel, and extensive site investigation, but clearer understanding of their actual extent and causes has resulted from convergence measurements, observations of ground behavior, initial support monitoring and detailed geologic mapping. Time-dependent movements, documented hours to months after excavation in clay-rich rock and in moderately to intensely fractured rock, identified squeezing areas, allowed classification by currently-used predictive methods and added to the list of lessons learned in tunneling such ground. INTRODUCTION In March 2003 the San Francisco Public Utilities Commission (SFPUC) authorized funding for the $4.6 billion Water System Improvement Program (WSIP) to repair, replace, and seismically upgrade its water system. The program consists of 35 local projects located within San Francisco and 48 regional projects located in several counties from the Sierra foothills to the San Francisco Bay Area. The New Irvington Tunnel (NIT), a key component of the WSIP, is located east of Fremont in Alameda County, on the east side of San Francisco Bay. The NIT is a new 18,660 foot (5,689 m), redundant tunnel, 190 to 670 feet (58–204 m) offset from, and subparallel to the Existing Irvington Tunnel (EIT). Built between 1928 and 1932, the EIT was constructed with an unreinforced cast-in-place concrete lining and is vulnerable to damage in the event of a major earthquake along the two closest active faults. The Hayward Fault is located less than a mile west of the tunnel, and the Calaveras Fault is located half a mile east of the tunnel. Although the alignment does not intersect these faults, the shaking and sympathetic displacement along secondary faults that cross the tunnel alignment are potential hazards. The NIT provides a seismically reliable water transmission facility capable of withstanding earthquake damage and maintaining continuous water service after a major earthquake. The NIT also adds system redundancy and provides for operation flexibility of running water through both tunnels, or through one tunnel while the other is out of service for inspections and maintenance."

Jan 1, 2016

By Richard A. Bideaux

During 1977 and 1978, a comprehensive study was made of the drill-hole data obtained by Urangesellschaft, USA, from their Juniper Ridge, WY, uranium deposits. This included uranium grade data acquisition, application of a variety of mineral deposit modeling techniques, and estimates of minable reserves, which pointed towards a possible production decision.

Jan 1, 1979

By Frederick P. Agterberg

It can be useful to model the mean grade values for a metal in mineral deposits containing that metal as representing the extreme value tail of a lognormal frequency distribution for the concentration values of the metal in rocks of all types. Results for copper and zinc in the Abitibi area of the Canadian Shield are compared to results previously obtained for the Canadian Appalachian Region. The lognormal model is also applied to a set of 162 large gold deposits in the Abitibi area. In the second part of the paper, 1311 large and small gold deposits in the Abitibi area are modelled as discrete events. By means of a newly developed spatial clustering model it is possible to predict the variances of random variables for frequencies of deposits in cells of different sizes.

Jan 1, 1979

A PDP 11/34 computer has been inter- faced to existing instrumentation in a 400 tph rod-mill/ball-mill grinding circuit and programed with a Kalman filter to estimate several unmeasured variables. A dynamic two-size- fraction model of the circuit is used to predict the complete state of the circuit including particle size distributions around the circuit, mass holdups and flowrates, the ball-mill grinding rate, water additions and cyclone parameters. Online measurements of sump level, slurry densities and product particle size are used to update the model values sequentially on a 20-second interval. This procedure results in optimal estimates of circuit variables given the relative reliability of measurements and the accuracy of the model.

Jan 1, 1983

By A. M. Tunstall

Blasting is commonly viewed separately from mechanical handling and crushing. This view is misleading because the degree of fragmentation achieved by blasting can have a significant effect on the efficiency of these processes and, hence, on the overall cost of the mining operation. In this paper, aspects of blasting and crushing and their interaction are examined. A case study is also presented that dramatically illustrates the influence of blast fragmentation on subsequent processing and on the financial implications involved

Jan 1, 1997

By Madan M. Singh

Section 516 of Public Law (PL) 95-87, commonly known as the Surface Mining Control and Reclamation Act of 1977 (SMCRA), requires that underground coal mine operators must "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonable foreseeable use of such surface lands, except in those instances where the mining technology used requires planned subsidence in a predictable and controlled manner..." Implied in the constraints of Section 516(b)(1) of SMCRA is a determination of what constitutes "material damage" to surface structures, renewable resource lands, and the capacity for sequential land use following underground mining. The authors have already briefly addressed the subject of damage criteria in relation to surface structures (Bhattacharya et al, 1984). In this paper, an attempt is made to provide quantitative guidelines to ascertain material damage to renewable resource lands, although the data available to establish these criteria are considerably more limited than is the case for surface structures. Besides, many more variables influence the severity of the impact at a given site, making the task of assigning stringent ground movement limits even more complex. This often necessitated use of professional judgement and occasional reverting to a qualitative approach. Hence the reader is cautioned at the very outset that the quantitative limits presented herein are approximate and are primarily intended to serve as rough guides for ascertaining the extent of damage to the renewable resource lands under consideration, and that depending on site-specific conditions the actual damage incurred may differ significantly from that predicted by the proposed criteria. The authors, however, feel that the criteria suggested are somewhat conservative, but realistic. The actual damage observed should generally be less severe than predicted by these criteria. It may also be clarified here that the term "subsidence", as used in this paper, implies the total phenomenon of surface and subsurface effects associated with the mining of minerals and not only the vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By Susan G. Bilhorn

A number of studies have been conducted in active and inactive mine environments using continuous monitoring and data acquisition systems to detect various parameters. In addition to the information obtained for research purposes, these monitoring systems can provide a means to remotely collect required information (such as radon daughter concentrations and air velocity) and control various conditions (such as fan operation and air door position) in numerous working sections of an active mine. Selection of detector locations and placement, which are critical to obtain the information and control desired while not inhibiting mine operations and influencing the detector readings, are covered in this paper.

Jan 1, 1984

By Madan M. Singh

With the current emphasis on ecology, safety, and conservation of natural resources, some consideration should be given to methods of mining that reduce surface damage, make the mining of coal less hazardous, and allow exploitation of a larger percentage of the coal in situ. One method that can be helpful toward attaining these objectives is the use of packing or stowing. Stowing involves the replacement of the ore that has been removed by waste material obtained from within the mine or elsewhere. Evidently, it would be most beneficial if this waste for packing were available from the mine being worked, but generally this is not possible. If complete stowing is adopted, it is necessary to bring in packing material from other sources. Stowing tends to reduce surface subsidence, but not eliminate it. It enhances roof support and curtails accumulation of methane in the gob, making the mining operations safer. It may also allow one to obtain a larger amount of coal. Currently, in the United States, a substantial amount of coal is left in place as pillars, in the hope that it will support the overburden indefinitely. Some of these could be extracted with stowing. The mining of thick, steep, or contiguous seams would also be facilitated.

Jan 1, 1974

By John E. Butler

Due to the present economic climate, particularly the depressed copper market, conventional mining, milling and flotation operations have been suspended. However, due to the apparent amenability of the ore to 'natural' leaching, investigations have been initiated into establishing an in-situ leaching operation as a preferred alternative to conventional operations. Cement copper production has been developed in parallel with the leaching trials and is presently at the rate of approximately 3,000 tonnes of contained copper per annum. Testwork includes controlled leaching of ore both in the laboratory and in-situ following blasting.

Jan 1, 1981

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By M. A. Anderson

After mope than fifty years Of Continuous operation, the Nevada Mines Division found itself faced with declining ore headings and metallurgical efficiencies, and rising operating costs. Although intensive process improvement programs had been initiated at various times in its history, insufficient return on investment served to defeat plans for any major changes in circuitry. The advent of practical large-volume flotation machinery, along with the success of long-range exploration drilling programs, complimented the results of an intensive program of research and development. The result of laboratory testing, pilot plant testing, and full scale plant tests was the proven indication of metallurgical improvement given increased flotation residence time and the effect of mechanical agitation in flotation.

Jan 1, 1975

By Elmer H. Citron

The Monterey Coal Company, a wholly owned subsidiary of The Carter Oil Company of Houston, Texas, recently awarded a contract to build the Monterey No. 1 Preparation Plant, which will be located near Carlinville, Illinois, to the McNally Pittsburg Manufacturing Corporation. The preparation plant will be one of the most modern jig preparation plants in the State of Illinois. Illinois No. 6 coal will be delivered by a 48" slope belt having 35-degree carrying idlers, operating at 650 FPM and operating on an incline of nearly 17 degrees. The slope belt is driven by two 450 BP motors and will deliver the mined coal at the rate of 1800 TPH to a stationary step-type ' screen having six-inch openings. The overproduct from the stationary screen will discharge into a 10' x 24' McNally Rotary Breaker and the underproduct will bypass the rotary breaker. The rotary breaker is equipped with heavy manganese screens with 6 ½" diameter openings. The sized 6" x 0 coal from the stationary step screen and the rotary breaker will be discharged by gravity to a 4%" raw coal incline storage belt. The 48" raw coal storage belt will deliver the 6" x 0 sized coal at the rate of 1800 T?H to an 8000 ton concrete raw coal silo, 70 feet in diameter and 1x7 feet high. The 6" x 0 sized coal will be drawn from the concrete storage silo by seven (7) 36" wide reciprocating plate feeders. Five feeders are to have constant speed drives at a rated capacity of 145 TPH each. Two (2) feeders will have remote con- trolled variable speed drives, to provide a varying feed.

Jan 1, 1970

By J. E. Jennings

The problems of slope stability in open-cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the ore body, This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ.

Jan 1, 1963

By Dmitriy A. Malovichko

The general theory for the description of seismic sources is briefly discussed. The effect of excavations on seismic radiation is considered. Expressions for seismic source mechanisms in terms of the geometrical and mechanical parameters of source processes are provided for the following cases: fault slip and shear failure in a confined environment, dynamic stress fracturing around a tunnel, rock fall, landslide and sudden subsidence. A classification of seismic events in mines based on source mechanisms is introduced. The classification separates blast-, slip- and crush-type events. Various approaches of analysis of source mechanisms involving forward modelling and inversion are discussed. The following examples demonstrating the utility of source mechanisms in mining are presented: forensic analysis of damaging seismic events, assessment of the increase in the depth of failure for dynamic stress fracturing around tunnels and its duration, examination of the rockmass deformation regime, assessment of deformation around tunnels using crush-type events, identification and parameterisation of weak geological structures, stress inversion from slip-type events. Finally, the requirements for seismic data to ensure high quality source mechanism solutions are briefly reviewed and future challenges in the interpretation and utilisation of seismic source mechanisms in mines are speculated on.

Apr 26, 2022

By W. Ghyoot, J. Boonstra, H. Dijkman, C. Buisman, M. Picavet

Paques and Umicore have demonstrated the feasibility of biological treatment of the highly complex Hoboken wastewaters in a1 m3/h pilot plant at Umicore Precious Metals, Hoboken, Belgium. In the first step arsenic was precipitated from copper smelter effluent as As2S3using biogenic produced H2S. Other metals such as copper, lead and cadmium were also removed as MeS to concentrations well below the discharge levels. Subsequently, sulfate and nitrate were removed to low concentrations (<300 mg/l and < 5 mg/l respectively) in high rate engineered bioreactors. Sulfide produced in the sulfate reduction process was recycled to step 1 for metals precipitation. Selenite/selenate was partly removed in the sulfide precipitation step, whereas the excess was biologically reduced and removed as selenium to concentrations <0.2 mg/l.

Jan 1, 2003

By M. A. Mahtab

This paper presents the results of a parametric study of the influence of natural features (stress field, rock strength, and strength and orientation of fractures) as well as the influence of induced features (undercut span, boundary slot, and other boundary-weakening measures) on the cavability of an undercut block of ore in mining by the block-caving method. The two-dimensional finite element analysis technique was used for this study. A coarse "mesh," along with linear homogeneous assumptions for rock properties, was used to model the problem of initiation of caving in a block of ore. Interpretation of the test results suggests that weakening the "abutments" of the block as well as certain orientations of natural fractures exercise significant influence on cavability. These findings hold promise for immediate application to known situations in block-caving mines.

Jan 1, 1975

By J. D. Miller

Physical separation of bitumen from low-grade Utah tar sand deposits containing a relatively high viscosity bitumen phase (Sunnyside and Tar Sand Triangle deposits) has been accomplished by traditional size reduction and froth flotation techniques. At appropriate experimental conditions more than 90 percent of the bitumen can be recovered in a concentrate, containing more than 20 weight percent bitumen, which should be a suitable feed material for subsequent hot water or thermal processing. The efficiency of bitumen recovery depends on the extent of size reduction, promoter and dispersant addition. Rejection of greater than 60 percent of the sand at ambient temperature and ease of water removal from the concentrate make such a process strategy both energy and cost effective. The energy required to achieve effective separation by the ambient temperature process is significantly less than the energy required for the recently developed hot water process. The flotation behavior of the tar sand has been analysed with respect to flotation pH, contact angle measurements and the apparent iso- electric point of the bitumen. The best flotation response at pH 7.8 to 9.0 can be correlated with the maximum in contact angle developed between the air bubble and bitumen surface and with the apparent iso-electric point of the bitumen (-pH 8.0).

Jan 1, 1981

By Lawrence Adler

The properties of a geologic mass may be considered from a resource or an engineering viewpoint. The primary engineering applications include ground control, excavation, bulk handling, and hydrology. This study will focus upon these areas in descending order. For an adequate geologic description, data is necessary on the following components: (1) the intact rock, (2) geologic structures, (3) contained fluids, and (4) existing pressures and temperatures, see Table 1. This information, combined with the engineering specifications, provides the basis for a formal geotechnical analysis as illustrated in Figure 1. For a structural analysis it is essential to establish the mechanical properties of the material composing the structure. This material, termed the "rock mass," consists mainly of the first two geologic components, the intact rock and geologic structures (Figure 1) Consideration of fluids will be subordinated to their role as chemical agents affecting the mechanical properties. The existence of pressures and temperatures generally lies beyond the scope of this study.

Jan 1, 1973

By K. G. Black

When one&apos;s attention moves from the control of a process unit or from the control of a department of similar units, to the control of an entire plant, two things must change. One is the techniques of control, and the other, the goal or purpose of control. The goal is no longer maintaining a certain quality of product or maintaining a particular flow rate through a process unit. The goal becomes economic - how to make the most money out of the plant. The principal control techniques become those of optimizing, rather than regulating. It is quite common to discuss the control of an entire plant in terms of three levels of control l; regulation, supervision, and optimization. Regulation is the control of inputs to a process unit at desired values. This is accomplished by two or three mode analog controllers or DDC loops. The second level of control is the selection of these desired values, e.g., set-points of the regulation controllers. The third level is to make such adjustments or corrections to the supervisory calculations so as to optimize the plant profit. It is immediately evident that supervisory control and optimizing control are intimately related, and a distinct dividing line cannot always be drawn between the two. Some authors prefer to add even more levels such as adaptive control and management information systems, but we believe our point is well made without further division of the functions which are necessary for complete plant control. To accomplish the economic goal, that is, the optimizing (maximizing) of the profit of a mineral processing plant, the plant should ideally be operated as if it were a separate company, buying its raw materials on the open market and selling its products on the open market. While petrochemical plants endeavor to operate in that manner, unfortunately this is not true of a mineral processing plant. The plant manager has to accept the amount and quality of ore the mining department delivers to him, and the products (concentrates) are delivered to another department of the company for further refining. In some cases he may sell

Jan 1, 1972