Search Documents

By Dennis A. Beiter, Kenneth G. Fields, Richard T. Stoltz

Section 56.5001 Title 30, [Code of Federal Regulations1], establishes requirements for respirable dust exposure in Metal and Nonmetal Mines based on the Threshold Limit Values (TLV's) adopted by the American Conference of Governmental Industrial Hygienists. Respirable dust samples collected by Mine Safety and Health Administration (MSHA) inspectors at a sandstone quarry showed certain workers were exposed to excessive concentrations during development of a "coyote tunnel" that was ventilated with a blowing system. Because exhausting face ventilation systems are known to control dust more effectively than blowing face systems, a change was proposed to improve worker respirable dust exposures. This paper describes the evaluation of the proposed exhausting ventilation system in the quarry's "coyote tunnel" and compares the respirable dust exposures with those measured by the MSHA inspectors with the blowing system. Results showed the proposed exhausting ventilation system reduced respirable dust exposures to less than 20 percent of those measured by MSHA inspectors when the blowing system was used.

Jan 1, 1993

A significant technological development is discussed for the processing of certain problem power plant flyashes which contain a high water soluble mineral content and which are known to yield inferior flyash based brick. This development is based on the addition of hydrochloric acid to the flyash-bottom ash-sodium silicate blends used for the production of flyash based structures. Favorable changes are evident in (1) sodium silicate consumption, where often approximately one-half of the amount used for making brick from normal flyash is required; (2) processing costs; and (3) strength and appearance of the resulting freshly formed green and fired structural products. In some high cost instances-(above the cost of 30 dollars or less per thousand brick estimated for normal flyashes) hydrochloric acid additions can replace or reduce other costly additives required with problem flyashes to result in a savings of as much as nine dollars per thousand brick. These developments offer promising possibilities for utilizing problem flyashes as well as flyashes which may come into contact with water soluble, sulfur as a result of the eventual application of certain experimental air pollution control processes.

Jan 1, 1968

By T. Krumins, L. Zunti, R. Frischmuth

"Titanium and titanium alloys are commonly selected for pressure oxidation autoclave vent piping and pressure control valve components, as well as autoclave internals and other process piping. In the autoclave vent application, titanium ignition risk is controlled by limiting oxygen concentration, and preventing high gas velocity gas impingement on surfaces. Oxygen concentration is dependent on the autoclave pressure and temperature operating conditions and therefore oxygen concentration and the associated titanium ignition risk is dependent on standard operating procedures, process control interlocks and permissive conditions. It is not uncommon for these standard controls to be deficient during atypical operating conditions, or for operations to deviate from the operating procedures, increasing the potential for a titanium ignition incident. Titanium ignition risk caused by elevated oxygen concentration in autoclave vent systems can be reduced with the introduction of an online autoclave overpressure calculation and the configuration of associated interlocks and permissive conditions. INTRODUCTION High temperature pressure oxidation (>190°C) is a well recognized and versatile metallurgical oxidative pre-treatment process commonly used to liberate gold from refractory sulphide ores and concentrates before conventional leaching with cyanide. Titanium and titanium alloys are highly corrosion resistant in pressure oxidation process conditions and are therefore commonly selected as materials of construction for many components including: autoclave internals, agitators, process piping, and components in autoclave vent systems. Operations that anticipate or have experienced aggressive corrosion in the vent system often have little choice in material selection other than the use of titanium (Krag & Henson, 1992). Titanium is not suitable for use with elevated oxygen concentrations and is considered a restricted material because of its high pyrophoricity and combustion propagation properties (Beeson, Smith, Stewart, 2007). Several serious incidents have occurred in which titanium materials have ignited in autoclave applications (Zawierucha, McIllroy, Million, 1995). In autoclave vent applications, titanium ignition risk is reduced by preventing elevated oxygen concentrations, maintaining low gas velocities, and minimizing the potential for gas impingement on surfaces. Oxygen concentration in the autoclave vapour phase and vent system is dependent on the autoclave operating pressure and temperature conditions and therefore titanium ignition prevention controls typically include process interlocks and operating procedures based on the selected nominal design operating conditions. However, it is not uncommon for these controls to be deficient or for operations to deviate from the nominal operating conditions over time, increasing the risk of titanium ignition. The introduction of an online calculation of autoclave overpressure and a maximum target autoclave pressure as well as associated process control interlocks and permissive conditions can alert the autoclave control room operator and prevent an elevated oxygen concentration from developing, and therefore reduce titanium ignition risk in autoclave vent systems."

Jan 1, 2016

By A. Cecala, J. Noll, J. Organiscak

Many underground metal/nonmetal mines are using enclosed cabs on mining equipment to reduce the exposure of miners to diesel particulate matter (DPM). However, some enclosed cab systems may not be meeting their expected efficiency in capturing DPM, which could be a result of inappropriate filter use, cab leaks or insufficient pressurization. NIOSH investigated several types of filters for reducing DPM to determine which type had the best capture efficiency. The laboratory results indicated that a MERV 8 (minimum efficiency reporting value, as defined by the American Society of Heating, Refrigerating and Air- Conditioning Engineers) filter captured about 50% of the DPM, a MERV 16 filter collected 96-98% of the DPM and two HEPA (high efficiency particulate air) grade filters captured over 99% of the DPM. NIOSH also performed a field study to measure the efficiency of two cabs at a limestone mine. The cab filtration systems of a loader and haul truck were found to be over 90% effective in removing DPM, except under certain operating conditions when the efficiency was as low as 41%. A possible reason for the low efficiencies is an open window in the cab, but more studies need performed to obtain a better understanding of the cause and solution of the problem.

Jan 1, 2011

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By G. Davis

Mineral properties and mineral firms often trade at a market value that is significantly greater than the value indicated by discounted cash flow (DCF) techniques. A possible explanation is that DCF analysis does not consider the value derived from managerial flexibility. Presumably, then, at least some of the difference between DCF value and market value is due to managerial flexibility. This paper surveys the recent attempts to empirically quantify the value of managerial flexibility using option pricing theory. The results indicate that managerial flexibility, at least as measured by the option pricing methodology, falls well short of explaining the gap between DCF value and market value.

Jan 1, 1995

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By Frank J. Klima

Explosives are probably the most widely used and most mysterious large scale' mining tools of modern times. The post black powder explosives were primarily nitroglycerin-based straight dynamites, ammonia dynamites, blasting gelatin, gelatin dynamites, ammonia gelatin dynamites, etc. Of these, the strongest and highest velocity explosive used in industrial operations is blasting gelatin, which is nitroglycerin colloided with a nitrocellulose of medium nitrogen content in proportions which give the product a plastic character, or about 93 to 7. Many variations of the basic groups above were developed by substituting ammonium nitrate and/or sodium nitrate for some of the nitroglycerin. The nitrates being insensitive to caps required a certain percentage of nitroglycerin to sustain detonation in smaller quantities or diameters. Paralleling the development of industrial dynamites was the development of more expensive, highly sophisticated explosives which were developed for specific military purposes. Such explosives as Amatol, RDX, Composition A, Composition B, Composition C, Lead Azide, PETN (Pentaerythritol Tetranitrate), Tetryl, Pentolite, TNT, etc., were primarily military explosives. Amatol, which is a cast mixture of ammonium nitrate and TNT (Trinitrotoluene), and identified by percentage of AN versus TNT as 50-50 Amatol, 80-20 Amatol, etc., was a favorite World War I explosive. RDX, or Cyclonite, was widely used in World War II. Also used during WW II were compositions A. B, and C, which were mixtures of RDX (Cyclotrimethylene trinitramine), TNT, and other nitrotoluenes. These high explosives, along with nitroglycerine, are exact chemical compositions or mixtures of exact chemical compositions which are individually explosive, or in other words, individually capable of explosive chemical decomposition when properly initiated. These chemical decompositions result in the formation of simpler compounds and/or large quantities of common combustion gases, and large amounts of energy in the form of heat. Of these, the most powerful is RDX which, based on the ballistic mortor test, is 1.5 times as powerful as TNT. Chemically, the decomposition of TNT releases about as much energy as the reaction of ammonium nitrate and fuel oil.

Jan 1, 1967

ShouSteel Mining Ltd., a subsidiary of ShouSteel (Group) Co., was founded in 1959 and is located in QianAn City in Hebei Province, China. ShouSteel?s pelletizing plant uses iron ore as a raw material combined with limestone, dolostone, or olivine, with bentonite as a binder. After mixing the raw materials and forming them into small, spherical balls, ShouSteel then fires pellets in kilns for hardening. The company sells the finished pellets as raw materials for blast furnaces used to produce industrial metals such as iron. ShouSteel?s handling capacity is approximately 24.5 Mt/a (27 million stpy) of ore. The company?s production capacity is 3.2 Mt/a (3.5 million stpy) of oxide pellets and 560 Mt (650 million st) of sinters. Until recently, ShouSteel Mining had not replaced its electronic scales in its series of ingredient chambers. Because of the wear and tear on these older scales, the weighing system began to encounter regular problems. The company experienced a high failure rate from the integrator, an unstable signal, weak anti-interference ability and low accuracy. ShouSteel also found that spare parts required during repairs were consistently high in cost and that system calibration was becoming increasingly frequent.

Jan 1, 2012

By P. Munjal

"Usage of Supercritical CO2 in place of high pressure freshwater has proven to be a potential breakthrough in the technique of fracturing. Tapping of carbon footprints from feasible sources like industries can be used to manufacture Supercritical CO2 required for fracking. Supercritical CO2, being less viscous than water, creates complex and coherent micro-fractures which can connect many more natural fractures greatly, increasing maximally the fractures’ conductivity leading to an increment in production. The better clean-up property of Supercritical CO2 provides auxiliary benefits of immediate evaluation of fracture zones, usage of an optimized quantity of mesh proppant and elimination of the need of swabbing. Also, Coal has a stronger affinity for CO2 than for CH4. When CO2 is present, CH4 on coal is replaced by CO2. This also ensures rigorous recovery of gas from the coal beds. Use of Supercritical CO2 will obliterate many problems as the CO2 used for fracturing is either sequestered beneath the crust or is recovered at the surface and reused. Therefore, injecting CO2 into coalbeds achieves not only enhanced CBM recovery, but also greenhouse sequestration underground. INTRODUCTION Coalbed Methane At various times in the geologic past, earth had dense forests in low-lying wetland areas. Due to natural processes such as flooding, these forests were buried underneath the soil. As more and more soil deposited over them, these dead plant remains were compressed. As the process continued the plant matter was protected from biodegradation and oxidation, usually by mud or acidic water. Under high pressure and high temperature, dead vegetation was slowly converted to coal. The omnibus process of formation of coal, thus, comprises of conversion of dead plant matter into peat, followed by its conversion to lignite, then sub-bituminous coal, after that bituminous coal, and lastly anthracite. This process of enrichment of coal as it is progressively forced deeper into an ambience with higher temperature and pressure involves biological and geological processes that take place over a long period and is called coalification. During coalification, large amounts of methane-rich gas are generated and stored within the coal on internal surfaces; hence comes coalbed methane. Coalbed methane (CBM), a gas formed as part of the geological processes that are responsible for the generation of coal, is adsorbed into the solid matrix of the coal during its formation process. Coalbed methane is distinct from a typical sandstone or other conventional gas reservoirs, as the methane is adsorbed and not absorbed. The methane is in a near-liquid state, lining the inside of pores within the coal. The open fractures in the coal that result from the liberation of volatile materials (and subsequent contraction due to the liberation) from the coal due to the high temperature and pressure conditions encountered, called cleats, may also contain free gas or can be saturated with water."

Jan 1, 2015

By J. W. Breen

ASARCO Incorporated has upgraded or is in the process of upgrading the Galena mine electrical, pumping, refrigeration, compressed air, ventilation, hoisting and rockburst monitoring systems to allow continued mining and development work on the 1 589-m (5,200-ft.) level and to provide services for projected deeper mining and development. Additionally, a separate lead-silver milling circuit has been added to the silver-copper mill to process lead-silver ore reserves. This paper describes completed and planned improvements made to date on these systems.

Jan 1, 1991

By W. L. Staker

The Bureau of Mines investigated selective extraction of Au and Ag from a low-grade Au ore containing Hg. Gold and silver were extracted from the ore in cyanide slurries, and Hg extraction was suppressed with sodium or calcium sulfide. Maximum Au extraction and minimum Hg extraction were obtained using solutions containing 0.34 lb NaCN/ton of solution. Increasing the cyanide concentration increased Hg extraction without increasing Au extraction. Mercury extraction from the ore was suppressed with 0-5 to 2.9 Pb CaS/lb Kg in the ore. Gold-to-mercury ratios of 100:1 to 400:1 were obtained in the leach solution, and on the activated carbon in a CIP circuit.

Jan 1, 1983

By N. Paas

Diesel powered equipment has been operated in underground coal for more than 50 years. According to the Mine Safety and Health Administration (MSHA), there are approximately 3,000 diesel units operating in underground coal mines in the United States. This number is expected to reach 5,000 diesel units in 250 coal mines by the year 2000. Also, there are approximately 5,000 diesel units operating in metal/nonmetal mines such as trona, potash and salt mines: and more than 3,000 diesel units operating in Canada. This increased popularity of diesel powered equipment over trolley wire, electric trailing cable or battery powered equipment is because of improved safety, greater mobility, higher productivity and increased power of diesel equipment.

Jan 1, 1997

By Lawson. Heather

"The purpose of this study is to explore how the geochemical and petrographic components of coal may impact its physical properties, as well as how these components correlate with a history of reportable dynamic failure in coal mines. Dynamic failure events, also termed bumps, bounces, or bursts, are the explosive failures of rock in a mining environment. These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of MSHA reportable cases. A database of variables was compiled using publicly available datasets, which included compositional geographic, strength, and Hardgrove Grindability Index (HGI) data (ACARP, 1998). Results indicate that bumping coals are less mature, lower in carbon, higher in oxygen, softer, and less well cleated than coals that do not bump. High liptinite content was found to correlate with higher average UCS values. However, no clear, direct correlation between UCS and dynamic failure status was observed. The findings of this study establish that differences exist between coals that have experienced reportable dynamic failure accidents versus those that have not. These differences are inherent to the coal itself, independent of mining-induced risk factors. Results further illuminate how compositional attributes of coal influence physical properties and begin to clarify potential links between geochemistry and dynamic failure status. Only through the better understanding of risk can more effective mitigating strategies be enacted.INTRODUCTIONDynamic failure events, also termed bumps, bounces, or bursts, are the sudden failures of rock in a mining or quarrying environment. Failure occurs when the rock’s critical bearing capacity has been exceeded and the rock fails energetically through the outward expulsion of rubblized material (Peng, 2008). These events occur suddenly and often with no warning, resulting in worker injury up to and including fatality in greater than 60% of reported cases through the Mine Safety and Health Administration (MSHA). Much research has been devoted to the prevention of these events. The effects of overburden depth and stiffness, mine design, mining practices, and in situ stresses are well documented (Agapito and Goodrich, 2000; Brauner, 1994; Campoli and Kertis, 1987; Holland and Thomas, 1954; Iannacchione and Zelanko, 1995; Lawson et al., 2016b; Mark, 2016; Newman, 2002; Peng, 2008; Whyatt, 2008). Despite these significant advancements in coal mine ground control, however, events continue to occur. Proactive risk mitigation remains an important research area. This is particularly true in underground coal settings, where the rockmass is layered, lithologically diverse, and does not exhibit consistent material properties across deposits.Many conditions have been associated with the occurrence of dynamic failure phenomena, including:"

Jan 1, 2019

By Jacques Bernazeaud

Rouez is a recent discovery of a major low-grade sulfide body (± 100 m, 0,6 % Cu, 0.3 % Pb, 1 ,5 % Zn, 21 g/t Ag, 1.5 g/t Au) in a populated farming area of Brittany, France, some 30 kilometres northwest of Le Mans. The discovery is the result of an airborne electro- magnetic (INPUT) survey. It is the first time that the INPUT method has been used in France. The survey Gas successful in spite of the numerous interferences normally found in populated areas. The lack of a good drainage system would not allow the discovery of Rouez using stream sediment geochemistry alone. Ground geophysical surveys confirmed the airborne work and gave sufficient information to make the first hole a discovery hole. The deposit is Proterozoic in age and sediment-hosted. The metamorphism is low grade.

Jan 1, 1983

By S. P. Brown, J. E. Worthington

Increasingly, exploration geology seems to be growing into a practice overly separated from production geology, yet the eventual purpose of exploration is a producing mine. To help in the search for new deposits, exploration "lessons" will be drawn from the papers given at the Fall AIME Applied Geology Symposium. In addition, examples will be re-emphasized to show how early observation of matters now routine to mine work (for example, hydrology, rock mechanics, oxidation state) can help increase the effectiveness of exploration.

Jan 1, 1992

By V. M. Johnston

The most abundant fuel resource in the U.S.A. is also the most under-utilized. Proven reserves of bituminous coal, sub-bituminous and lignite constitute from 60% to 90% of our total fossil fuel reserves -- dependent upon the parameters used by the analyst making the estimate. Despite this ample supply, bituminous coal provided only 20% of U. S. energy consumption in 1967 and 1968, this dropping to 17.57 in 1971 and 1972. By 1978, according to my projections, 16.7% of the Nation's mechanical energy will come from bituminous coal. However, our energy needs are growing at such a rate that the 20.6% provided by bituminous in 1967 equalled 480 million tons while the 16.7% of U. S. consumption visualized for 1978 will require nearly 650 million tons. In order to view coal's position with perspective in this developing energy crunch, it is necessary to examine the total energy situation. To this end, I have prepared a couple of tables which you should have before you. I chose this procedure rather than slides because I would need to utilize an entire wall to make the data visible to an audience. Therefore, I refer you to the long sheet entitled "U. S. Energy Consumption - Trillion Btu - 1967-1978." As you can see from the heading, I am confining my treatment of the problem to the intermediate term. In the long run, if we are willing to pay the cost, we can do a lot of things, including the complete conversion of coal into a sulfur-free fuel.

Jan 1, 1973

By P. A. Roberts

A proposal for a modified in situ leaching method for extracting gold from oxidized gold ores using a non-cyanide lixiviant is described. A non-cyanide lixiviant is suggested because of the obvious concerns posed by injecting cyanide-bearing solutions into the subsurface. Oxidized gold ores were chosen as a focus because earlier research on the use of sodium thiosulfate as a lixiviant under anaerobic conditions indicated that the presence of pyrite led to rapid thiosulfate breakdown. A reconnaissance research program involving ore characterization and hydrometallurgical test work on samples from four Australian ore deposits and preliminary reactive transport modeling studies was carried out. This work showed that lixiviant-oxidant combinations of sodium thiosulfate and ferric EDTA and iodide and iodine are both capable of extracting high percentages of accessible gold from the selected samples in bottle roll tests under anaerobic conditions. The ore characterization and reactive transport studies suggested that both physical and chemical methods of permeability enhancement may be required to lift bulk permeability and the availability of gold for dissolution to sufficiently high levels to obtain adequate gold recoveries. Assuming that such methods prove to be both necessary and economically viable, the mining method would no longer be regarded as simple in situ leaching. Therefore, the term ?in-place leaching? has been adopted for the proposed gold extraction system.

Jan 1, 2010

By B. Denby

Recent advances in Virtual Reality (VR) technology have resulted in major opportunities to improve safety training of mine workers, supervisors and managers. The hazardous nature of both surface and underground environments limits the type of safety training that can be carried out. VR offers the potential to expose mine personnel to hazardous situations in a safe, highly visual and interactive manner. Customized simulations of mine layouts, dynamic operations and mine environment can be set up and mine personnel can be allowed to move around the virtual mine, making decisions at key points. The consequences of both correct and incorrect decisions can be immediately fed back to the trainee.

Jan 1, 1998

By E. McCullough

"Fostering positive community relations is a principal tenet of sustainable development, but conflict can test even the strongest of relationships. While conflict surrounding resource development projects has the potential to be destructive, it may actually pose opportunities for partnership and collaboration when managed effectively. It is therefore not only important for mineral resource professionals to recognize the financial and social costs associated with legal disputes among project stakeholders, but also for them to prioritize resolving social conflict using alternative channels that allow for win-win outcomes. A variety of dispute prevention and resolution techniques do exist, but successful practice is not yet the norm. Here we review the sources and consequences of social conflict in the context of mining projects, and discuss typical and alternative approaches to conflict management in light of their respective benefits and drawbacks. We also suggest implementation of conflict resolution lessons into resource-related university curricula as a critical step in the continued shift of the mining industry towards sustainable development. INTRODUCTION Social conflict is a recurring phenomenon in the human experience and serves as a critical mechanism for change [1-5]. It occurs when two or more parties perceive that their needs and interests are in direct competition with each other and believe they cannot be reasonably accommodated. Conflict over mineral resource activities, particularly the distribution of benefit and risk, has become an omnipresent issue throughout the world [6-7]. Contrary to common perception, however, conflict can be a positive, transformative encounter in some instances [2, 8-11]. For this to be possible, society and its acting agents must reconsider how to address conflict. What if conflict were only a challenge to try something different? It is well-understood that the mineral industries must manage an increasingly significant volume of social conflict [12-13], which can be a costly externality impacting all of whom are involved. We commonly consider conflict in a two-party sense, but this deeply over-simplifies the true number of stakeholders. Besides mining companies and community members, government policymakers and regulators, public interest groups, and judicial systems, to name a few, bear the social expenses of poorly-managed conflict [4, 6, 12, 14-22]. It is desirable for interested parties to participate actively in a constructive way to pursue their needs rather than contributing to adversarial relationships, operational problems, and legal costs [1, 4, 12]. Some mining companies are of course already working to develop more productive relationships with their stakeholders, but there is undoubtedly still a gap between ideal and common practices. This gap can inhibit collaboration and threaten the potential for mutually-beneficial resolutions to complex social issues [12]."

Jan 1, 2016