Search Documents

By Mohammad R. Jafari

The Camp Dresser & McKee (CDM) has been retained by the Sacramento Regional County Sanitation District (SRCSD) to design the Mather Interceptor, a portion of the South Interceptor and Mather Interceptor program. The Mather Interceptor consists of 14,667 feet of 54 to 72 inch gravity interceptor. Approximately 90 percent of the alignment will be constructed via tunneling. Cobbles and boulders in a sand/gravel matrix dominate the ground conditions combined with seasonal perched groundwater table at some of the deeper reaches of the alignment, impacting design consideration. This paper will present the results of a comprehensive geotechnical investigation conducted for this project and in-depth technical evaluation of various trenchless techniques feasible for tunneling in the cobble and boulder laden formations of this project. This paper will also present the risks and issues of the design alternatives and selection criteria.

By R. C. Milici

Historical production data and reserve decline rates can be used both to predict future coal production rates and to estimate when the reserve will be depleted. Reserve estimates inferred herein from historical production data and decline rates are commonly lower than estimates made from geologic data. The latter include significant amounts of lower quality (deeper, thinner, higher sub) coal which may be mined when the better deposits are depleted.

Feb 24, 1997

By Thomas C. Shapiro

This is the second in a series of articles on microcomputers and applications in the minerals industry. The first article (ME, Feb., page 129) discussed microcomputer terms and concepts. This article will discuss software for geology and mining. The third article will cover plant, administrative, and geotechnical software applications. Introduction Geology and exploration are areas where computers have a natural fit. Large volumes of data need to be tabulated, evaluated, and made into maps and reports that allow geologists and management to make a decision on a project or mine. Until recently, the programs that performed these tasks were cumbersome and not user friendly by any stretch of the imagination. Learning time to become an expert in these programs typically would be six months or more. The computers needed to run these programs are expensive mainframes. Several years ago, the use of minicomputers became popular because of their lower cost. Programs were adapted to fit these smaller machines and became friendlier. With the advent of micros, many programs. were rewritten and used the screen capability more effectively, thus providing a real advance in user interface. Programs and Price The definition of micro, mini, and mainframe is becoming blurred. For the purposes of this article, micro refers to either an eight- or 16-bit computer, costing less than $10,000 and, more typically, under $5,000. Mini refers to a 16- or 32-bit computer that typically costs more than $25,000. Mainframe refers to a 32-bit or larger computer that costs more than $250,000. There is a large gray area between micros and minis, and minis and mainframes. Technology and prices are changing so fast that the traditional definitions have become almost meaningless and price has become a better guide. With the arrival of the minicomputer, costs for hardware began to fall, but the programs have tended to remain unfriendly. In some cases, the minicomputer acted as a front end to the mainframe. Cost of both the programs and minicomputers could easily run a minimum of $70,000. A total cost of $200,000 would not have been out of line. The average geologist and company would have a great deal of difficulty justifying such a purchase. The advent of the microcomputer has changed all that. For $3,500 to $5,000, one can buy a 16-bit micro and a printer. Plotters with six pens are available for $2,000 that will produce a 280- x 430-mm (11- x17-in.) map. For several hundred dollars, software is available to act as a word processor, an economic spread sheet, or to perform ground water calculations. In fact, some programs are available for free. Some of these programs are relatively easy to learn. In addition, programs are being developed daily that are easy to use. More importantly, large programs that once ran only on mainframes are being converted

Jan 3, 1984

By F. Calizaya

This paper describes the basic requirements for the utilization of belt air to ventilate working sections at remote locations in relation to the main fans. It highlights the risks involved, potential problems, and the provisions that must be followed by mine operators for the safe use of belt air. The paper also presents a brief review of the current regulations, conveyor belting tests, atmospheric monitoring system requirements, and the experience gained by mine operators to utilize the belt entries to ventilate remote working sections or areas where mechanized equipment is being installed or removed. The paper concludes with a set of recommendations with respect to the utilization of belt air and the composition of belt material in under-ground coal mines.

Jan 1, 2008

By C. Bise, A. Seal

Excessive noise has long been a hazard in the coal-mining industry. Studies conducted during both the mid-1970s and the mid-1990s consistently show that hearing hearing loss within the mining industry persists, in spite of regulatory requirements and sampling technology advances. When MSHA’s new health standards to protect miners from hearing loss took effect in September 2000, the potential developed to re-evaluate sampling approaches with regard to noise-source hazards, such as task-based methods. This paper describes results from a Penn State research project currently being conducted at an underground coal mine. Each occupation was reviewed, and a list of tasks or processes performed by each was generated. Traditional personal noise dosimetry, static sound pressure levels, and equipment sound mappings have been performed. Job tasks indicating the greatest levels of daily noise exposure and contributions to noise dose have been identified and will be discussed.

Jan 1, 2001

By Richard F. Flanagan, Robert H. Marshall

The Republic of Singapore’s Public Utilities Board is implementing the Deep Tunnel Sewerage System Project. The project’s deep tunnel component, 48 km of deep, large diameter sewer tunnels has been successfully completed (the works are in the defects liability period). Six International Design/Build tunnel contracts utilized eight Earth Pressure Balance TBMs ranging up to 7.23 m in diameter to deal with varied ground types ranging from deep soft clays to fresh granite. Numerous access/workshafts were constructed and using various support systems. This paper provides an assessment/overview of the tunnel contracts, tunnel excavation methods and equipment, and the shaft systems. Suggested enhancements to similar future projects are provided.

Jan 1, 2007

By Steve Kral

In a lagging economy where profits are tight, businesses cut costs. No revelation there. The mining industry, though, has always looked for ways to reduce production costs — no matter the state of the economy or commodity prices. The fact is, when planning a new mine or the expansion of an existing one, mining companies gamble that commodity prices will be reasonably high when a project comes onstream. It takes millions of dollars and several years to bring a mine into operation. And a lot can happen economically between the time management gives the go-ahead for a new project and its completion.

Jan 1, 2002

By W. G. Pariseau

Conventional barrier pillars in underground coal mines are intended to protect mains and sub-main entries for relatively long periods of time. Inter-panel barrier pillars that may be used in especially deep coal mines, say, below 800 m (2,400 ft), are intended to protect longwall panel faces and adjacent panel entries for the life of nearby panels. Barrier pillar failures have serious consequences, especially when failure is sudden and catastrophic. Design of barrier pillars is thus of considerable importance to safety and efficiency of operations. Locally, failure occurs at the limit to elasticity when stress tends to exceed strength. Strength of rock is stress dependent, so an analysis of stress is central to rational design of barrier pillars. There are several approaches to stress analysis for coal mine pillar design that range from the simplified but popular tributary area method including variations that use empirical definitions of the tributary area (volume) to more sophisticated numerical methods such as the boundary element method and the finite element method. Despite ease of use, empirical methods are limited and always suspect when applied to conditions beyond their scope of definition, while boundary element methods do not generally include pillars in the solution domain. The finite element method is not so restricted and thus is a natural choice for conventional and inter-panel barrier pillar safety analyses. Caving of roof strata certainly affects the distribution of stress about longwall faces and nearby barrier pillars. Conventional wisdom that considers roof strata to respond as cantilever beams indicates the longer the span the greater are loads on longwall faces and face supports. Failure of roof beams, caving, shortens spans and relieves face and support loads. The same view is applicable to barrier pillars in that long roof spans outside of barrier pillars leads to higher pillar loads than short spans. Hence, caving should be beneficial to barrier pillar safety. However, the benefit may be small depending on the extent of caving and only in the form of a slight reduction in overburden weight transmitted to the barrier pillar, especially in case of inter-panel barrier pillars. FINITE ELEMENT MODEL Finite element models for stress analysis in rock mechanics are formulated in consideration of physical laws, kinematics, and material laws. These models meet the essential requirements for equilibrium of stress, satisfy strain displacements relations, and in a general sense, relate stress to strain through material laws, often referred to as constitutive relations. The last may be complex and replete with nonlinearities. A de facto engineering material law is the elastic model in the form of Hooke?s law for linear, homogeneous materials that may be anisotropic. A limit to elasticity is imposed by strength in the form of a failure criterion or yield function that accommodates triaxial stress states. Examples used in rock mechanics are the well-known Mohr-Coulomb (MC)criterion, the popular Hoek-Brown (HB) criterion, and the Drucker-Prager (DP) criterion. The first is linear in stress, while the second is nonlinear. Both do not include any effect of the intermediate principal stress. The last is also linear in stress but includes the intermediate principal stress. All show an increase in the major principal stress at failure with confining pressure. In the UT2/3 finite element programs, the failure criterion Y is a nonlinear, anisotropic form and is also the plastic potential [1]: [YJI=+ 11NYJI=+- (1) ] where N is an exponent, usually 2, and J2 and I1 are nonlinear anisotropic forms of the second invariant of deviatoric stress and the first invariant of principal stress. The form (1) reduces to DP when N=1and isotropy prevails. When Y = 1, the limit to elasticity is reached and plastic deformation is possible. The material constants that enter (1) are all computed from unconfined compressive, tensile, and, in case of anisotropy, shear strengths. These latter strengths may be estimated from conventional laboratory test data. Of course, joints in field-scale rock masses induce different values. How different is often a matter of conjecture. For comparative studies, laboratory rock properties seem adequate. Inelastic, that is, plastic behavior occurs with strain beyond the elastic limit. Strain hardening, ideal plasticity, and strain softening are possibilities. Ideally brittle behavior with complete loss of strength is an extreme form of strain softening [2]. Caving may also be considered as strain softening with a less drastic reduction of material properties. As intact roof strata fail, fall, and form a rubble pile below, a new material is formed with greatly reduced elastic moduli and strengths, say, 1/100th of the original intact moduli and strengths. From another viewpoint, caving is simply a natural cut and fill process. Input for stress analysis by the finite element method includes: 1. Preexcavation stress state 2. Geology (stratigraphic column) 3. Structure (major faults, joint sets) 4. Elastic moduli 5. Strengths, and specific gravities of each rock type 6. Excavation sequence Output from an analysis includes distributions of: 1. Stress 2. Strain 3. Displacement 4. Local factor of safety (element fs) The last is defined as the ratio of strength to stress and in view of the failure criterion (1), is the ratio [fsJstrengthJstress=] where the numerator is the maximum possible value and the denominator is the actual value of the square root of the second invariant of deviatoric stress. This invariant is a measure of shear stress intensity but also reduces to uniaxial tensile and compressive strengths as the case may be. An fs greater than 1 indicates an elastic state of element stress; a value of 1 indicates the limit to

Jan 1, 2009

By Steve Kral

More than 124,000 people involved in the mining and construction industries throughout the world poured into Las Vegas, NV in March for ConExpo-Con/Agg ’99. Show organizers said this triennial exhibition is the largest equipment show in the Western Hemisphere and one of the largest exhibition of any industry. “Clearly, Con-Expo-Con/Agg ’99 was one of the largest trade shows of any industry ever held in the Western Hemisphere,” said Bruno Benna, co-chair of the event. Attendees included mining industry representatives, including aggregates, and sand and gravel producers. In addition, many of the attendees work in the construction, reclamation, forestry, asphalt paving, landscaping and concrete industries. According to show records, about 52% of those attending were company presidents, vice presidents, chief financial officers or managers.

Jan 1, 1999

By Jay Nopola, Christopher Johnson, Matthew Minnick, Erik Hemstad, Erik Walega

Mining data collection, storage, and interpretation methods have progressively changed over time. Data collection, for the most part, has transitioned from handwritten notes and logs based on manual gauge readings to real-time data streaming through instrumentation capable of directly communicating with site-based data historians or cloud storage. Data collection and storage have had to adjust commensurately with the volume of data, leading to more complex database architecture. Geoscience interpretation methods have also changed; however, the first goals of modeling and understandings from first principles remain the same and are typically deeply rooted in historical academic work. Machine learning methods are becoming more common, available, and implemented by industry and practitioners. Despite the wide accessibility of machine learning methods, the population of geoscience subject matter experts in the underlying theory of this analysis type is limited. This form of analysis, therefore, must be conducted carefully and in conjunction with subject matter experts, on both machine learning theory and the field it is being applied to. This paper aims to provide background history on data analytics and machine learning, current methods and practices, and high-level geoscience case study examples, as well as take aways regarding the mining industry, potential pitfalls specific to geosciences, and possible perspectives on the direction of artificial intelligence in the future.

Jun 25, 2023

By D. Conklin

Annual fish monitoring of the Red River, NM from the town of Red River to downstream of Questa, NM has been conducted since 1997. This long-term dataset, sponsored by the Chevron Mining Inc. Questa Mine provides an opportunity to evaluate the fish community response to natural phenomena, such as landslides and drought. Hydrothermal scars are present on drainages to the Red River, which can contribute large quantities of sediment to the Red River during localized storm events. Sediment inputs from the hydrothermal scars result in decreased habitat and water quality conditions within the Red River. Landslides from the hydrothermal scars contributed large amounts of sediment to the Red River in the summers of 2002 and 2007. Resident trout populations in the Red River after summer 2002 were depressed at sites adjacent to and downstream of the hydrothermal scars. Resident trout populations had begun to recover by 2005 and 2006; however, after the summer 2007 landslide, the resident trout population was again drastically reduced. In fall 2007, 13 resident trout were collected from 11 sites in the approximately 23 km reach of the river, compared to 691 from the same 11 sites in fall 2006. Resident trout density and biomass has gradually increased since fall 2007, and flows have removed sediment from the study reach. A combination of increased sedimentation and decreased water quality were likely responsible for the decreased resident trout populations in the Red River. Drought and the lack of flushing flows appeared to exacerbate the problem of high sedimentation levels from 2001 to 2004. Climate models predict prolonged periods of drought and increased intensity of storm events, potentially resulting in less favorable conditions for the resident trout population of the Red River in this area.

Jan 1, 2011

By Darrell Gillis

Recent accidents in the United States underground Coal Mines and the on-going carnage in Underground Chinese Coal Mines has shown the danger associated with the lack of communication infrastructures in an underground environment. The US Mine Safety and Health Administration (MSHA) have introduced legislation that states all Underground Coal Mines must have two-way voice and personnel tracking capabilities by 2009. If Coal Mining companies are being forced to deal with this problem Tunneling Companies will not be far behind. This paper will examine current practices and best case technology to deal with these issues.

Jan 1, 2007

By Gregory T. Ziegler

A complex soil profile and high water table, together with a below-grade active subway tunnel, an above-ground elevated railway line, and the heavily travelled Northern Boulevard all passing above the tunnel alignment, combined to make mining of New York?s Northern Boulevard Crossing what is widely considered to be the most challenging portion of the multi-billion-dollar East Side Access project. The Northern Boulevard Crossing is a vital link in this project which, when completed, will connect the Long Island Railroad to Grand Central Terminal in Manhattan. How the sequential excavation method (SEM) tunneling was successfully accomplished, despite the obstacles, was a textbook exercise in practical innovation coupled with close cooperation between the owner, the construction manager, Hatch Mott MacDonald, the designer, Parsons Brinckerhoff, the contractor, Schiavone-Kiewit, and spe-cialty geotechnical contractor, Moretrench.

Sep 1, 2013

By R. C. Burtan

Long before recorded history, man began to dig into the earth's crust in a never ending search for useful materials. It is well known that more than half of the earth's crust is composed of silicon dioxide (SiO2), also known as silica. Silica and silica-containing material have a great many uses in modern society. This material, however, is potentially an extreme health hazard. Silicosis: Not a New Disease Centuries before the Christian Era, Hippocrates wrote of a lung disease common to those who mined in hard rock. He was obviously describing silicosis. It is also apparent from ancient writings that the Egyptians were aware of this malady. Dioscorides also wrote on this subject in the fifth century B.C. It is undoubtedly the oldest and best studied of the occupational lung diseases. Silicosis was certainly described by Agricola in his De Re Metallica published in 1556. Here he described lung disease among hard-rock miners. The original document was written in Latin and then translated in 1912 by Hoover and Hoover. One of these translators was Herbert L. Hoover, a former US president who once made his living as a mining engineer. More recently, there are numerous references in medical literature in the 19th and 20th centuries relating silica exposure to silicosis. There are specific references to mining in hard rock, as well as to sandblasting and a host of other industrial exposures. In 1919, Winslow described standards for measuring the efficiency of exhaust systems in polishing shops using sandblasting. These standards were equally applicable in the mining industry. As early as 1920, Winslow explored the efficiency of certain devices used to protect sand-blasters against the dust hazard. These devices were equally applicable in the hard-rock mining industry. The medical community recognized the silica health hazard in the early 1900s. Middleton described the illness in the British Medical Journal in 1929. He noted the danger to health at that time. D. Hunter mentions in his book, The Diseases of Occupations (1969), the monumental work of Merryweather in 1936, in which he surveyed the silicosis risk in Great Britain. He showed statistically that the average employment length of sandblasters who ultimately died of silicosis was 10.3 years, compared to 40.1 years for all fatal cases, irrespective of occupation. Sandblasting and hard-rock mining and drilling, obviously, are very hazardous occupations. Weil and Zisking of Tulane University wrote in 1975 that "it was known as early as 1935 that the course of silicosis is much more rapid in sandblasters than in miners or foundry workers. This can be explained by the fact that sandblasters are exposed to an almost pure siliceous dust containing high concentrations of respirable particles within the range of 1 to 3 micron size." Protecting the Worker The medical community recognized in the early 1900s the need for proper protective equipment for all of those who worked with siliceous materials. Middleton, writing in 1929, said: "The worker is then protected by a close fitting helmet with an air feed, much as in the case of an underwater diver. In spite of these precautions, cases of silicosis among sandblasters are being met with today. It is a matter for serious consideration whether a substitute, such as steel or iron grit, could not be used to replace the siliceous grit as the abrading material." C. E. A. Winslow, a professor of public health at Yale School of Medicine, and others wrote of the need to protect sandblasters by

Jan 7, 1984

By William R. Yernberg

The Fifth International Heavy Minerals Conference (HMC) was held Oct. 16-19, 2005, at the Marriott Sawgrass Resort in Ponte Vedra, FL. With SME as sponsor, the 2005 conference marked the first time that the HMC was held in North America. The conference is held every two years and provides an important forum for professionals in the heavy minerals and related industries to meet and discuss issues related to heavy mineral exploration, mining, processing and marketing. Previous locations included Australia and South Africa. The conference consisted of technical presentations, field trips to heavy mineral operations, a trade show and social activities. It was appropriate that Ponte Vedra was selected as the location for the conference. Ponte Vedra, located on the Atlantic Coast 17 km (10 miles) southeast of Jacksonville, FL, is the birthplace of heavy minerals mining in North America. Ponte Vedra beaches were mined from 1916 to 1929 in what was then called Mineral City. Though Ponte Vedra is now a golf and beach resort, there are still four heavy mineral mines operating within an hour’s drive. Today the Ponte Vedra Country Club and Golf Course is situated in the center of the former mining site.

Jan 1, 2006

By Dale S. Hursh, William A. Brooks

Introduction US dependence on external energy sources is dangerous because of unstable political situations existing in key energy exporting countries. So, recent national energy policies call for increased reliance on domestic energy sources. Coal ranks as the most feasible domestic energy source due to its abundant reserves and continental distribution. But to efficiently extract these coal reserves, huge sums of capital funds are needed. Due to the depressed economy, lenders of capital funds are forced to be more stringent with loan applications. This results in fewer loans granted. In many cases, it is uncertain if funding can be obtained. Furthermore, the greatest level of domestic mine financing is expected to be in the coal sector. Demand for capital in the domestic coal industry is anticipated to increase 80% by 1990. The Chase Manhattan Bank in New York warns that these future needs cannot be met by the present capital markets. This article analyzes the current and expected situations of the capital markets available to the domestic coal industry, including: • current and expected future types of financing used in the domestic coal industry; • problems the domestic coal industry may encounter as it seeks capital; and • the future availability of capital funds as concluded from analysis of the first two items. Background Information Regardless of industry, all projects or ventures can be divided into four basic stages: generation; evaluation; selection; and execution. Within the mining industry, one can break down these stages to draw a clear picture of mine development, as shown in Fig. 1. Each successive stage has a corresponding risk level. This risk level defines the type of financing available to the mine operator. Mining Venture Risks A coal mining venture can be characterized by its unique blend of technical and financial risk. As the mine moves through different development stages, varying proportions of each of these risks are encountered. It is these risks that the lender evaluates to determine project suitability. For a coal mining venture, the major complexities generally occur with the technical risk. These include: • quantifying the coal reserves: • assessing the feasibility of the mining method; and • evaluating the design of the wash plant. The reserve risk is gauged by the amount of measured, mineable, and saleable reserves. The greater the latter amounts, the lower the risk. Secure title to the reserves plus title for any surface areas required are also of concern to the banker. Feasibility of the mining method and evaluation of the wash plant design should verify that the project can be completed according to the engineered spec-

Jan 9, 1982

By D. W. Partridge, W. Lamb, A. E. Lamb, S. Bird

Due to the constant need to improve SAG mill performance and efficiency, extensive research into all aspects of SAG mill optimization has been performed. This paper will review the current evolution of SAG mill shell liner design and their performance at the Copperton Concentrator. The effect of these liner design changes will be discussed with respect to: • Liner configurations • Mill operating performance, i.e., throughput, power draw, mill control • Mill mechanical performance, i.e., liner wear profiles, liner life, liner breakage, liner hardness • Foundry manufacturing considerations • Economic evaluation of throughput versus liner life This paper will discuss the results of Kennecott Utah Copper’s (KUC) and ME International’s (MEI) test work, providing an insight into the past, present and potential future opportunities of SAG mill liner design.

Jan 1, 2002

By Jacek B. Stypulkowski

This paper discusses the challenges faced by the design team of the under-river crossings of electric transmission feeders in New York City, a densely populated urban area. The under-river crossing of a 345 kV feeder was initially designed as Horizontal Directional Drilling (HDD), but was redesigned as a utility tunnel because of site con¬straints on both sides of the river. Multiple studies addressed location, available tech-nologies and costs. Multiple soil investigation phases addressed design aspects of HDD, as well as tunneling. Contractual issues varied from a design build alternative with Geotechnical Data Report (GDR) to design tender approach with GDR & Geotechnical Baseline Report (GBR).

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

By Jafar Khademi Hamidi

The Zagros long tunnel is one of the main components of Sirvan water transfer project in western Iran. It is approximately 48 km in length and consisted of two lots. The second 26 km lot of this tunnel is under construction by a 6.73 m diameter double shield (DS) TBM. The tunnel passes through several formations with wide range rock mass qualities. During the tunnel alignment, changes in rock quality were highly frequent from poor to very good. The encountered geological conditions required TBM operation to change frequently from hard rock to soft, dry to flowing, sticky to nonsticky ground (and vice versa), more often than expected. In the course of tunneling, the machine has encountered nearly many adverse geologic conditions. The most important problems have been sudden high volume water inflow into the tunnel, sticky ground, and gas seepage, all of which resulted in reduced TBM advance rates. This study will high-light two difficult ground conditions including large water ingress and sticky ground and also the related problems encountered by the TBM along 8 km of excavated tunnel. In sticky grounds, cleaning of the clogged cutter head caused many delays and contributed to additional downtime. Application of some operational modifications, including decreased TBM thrust showed satisfactory results in such cases. While reduced thrust resulted in reduced penetration rate, but the overall TBM advance was greatly improved by the increase utilization rate and elimination of down time related to cleaning of the head. To cope with high water inflow, application of preventive measures such as pre-grouting has proved to be a more efficientsolution. The sealing of ground water inflow also decreased seepage of dangerous H2S gas and other chemicals such as hydrocarbons accompanying the groundwater.