Search Documents

By Gilbert A. Bonforte, Hugh P. Caspe, Tracy K. Lundin

The Narragansett Bay Commission (NBC) Combined Sewer Overflow Abatement Program is a major effort to address and mitigate discharges from combined sewer overflows in the Providence, Rhode Island area. The proposed system consists of three deep rock tunnel segments totaling 17.8 km (11.1 miles) in length that will provide 860,000 cu m (227 million gal) of storage at depths up to 99m (325 ft). This paper discusses 13.5 km (8.4 miles) of 6.64m (21.8 ft) finished diameter tunnel, four construction shafts, 19 dropshafts and one large diameter pump station shaft tapered from 1 5.2m (50 ft) at the surface to 27.4m (90 ft) at depth. All facilities are in preliminary design.

Jan 1, 1995

By P. A. Schmitz

The characteristics of gold leaching from carbonaceous matter by sodium cyanide, and sorption of gold cyanide to carbonaceous matter in autoclaved and non -autoclaved gold ore from Barrick Goldstrike Mines Inc. (BGMI), Nevada, was investigated. Much greater gold cyanide complex sorption was observed for the carbonaceous matter in high preg-robbing ores relative to the low preg-robbing ores. This observation corroborates previous reports that have attributed observed preg-robbing behavior to the carbon in the ore. Gold cyanide complex sorption was found to be reversible for carbonaceous matter from low preg-robbing ore, but was irreversible for carbonaceous matter from high preg-robbing ores. Autoclaving the ore appeared to enhance the sorptive behavior of the carbonaceous matter from both high and low preg-robbing ores.

Jan 1, 1999

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By Ronald J. Roman

As in every business venture, the primary objective of a mining operation is to make money for those who supply the venture capital. Therefore, all decisions concerning the operation of the mining operation should be made in light of the resulting effect on profit. The ultimate control is on profit, but the process is controlled, for example, by aiming for a recovery or concentrate grade knowing its effect on profit. The normal procedure used to determi.ne the profitability of a venture is to "present worth" all costs and incomes back to some arbitrary year zero. Every company has formed a management decision as to what it will require as a minimum return before it will undertake an investment. Once the economic analysis is completed, investment will be made only if the venture shows a positive present worth. If two alternatives are available, the alternative with the larger positive present worth is the one chosen. The same principles can be applied to the selection of a production schedule.

Jan 1, 1971

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By Ezz El Din Abdel Hakim Khalaf, Khalid S. Essa, Marc Munschy, Mohamed A. S. Youssef

This study focused on joint interpretation of the aeromagnetic and radiometric data to allocate and describe the structural elements and mineralization zones such as uranium, gold, and sulfide in the Gebel Umm Tineidba and its surroundings, Eastern Desert, Egypt. The study region is covered by exposures of Precambrian rocks such as gneisses, migmatites, ophiolitic mélange, metavolcanics, younger granites, and Quaternary sedimentary covers. The application of the total intensity magnetic and reduced-to-pole maps, power spectrum, analytic signal, tilt-angle, and local wavenumber maps helps in recognizing magnetic sources distribution, lineament features, and mineral zones delineation. The obtained results indicate that the depths of the deeper NE–SW, NNE–SSW, and N–S trending structures extend from 400 to 1750 m and shallower ones range from 100 to 400 m. Finally, the main trends of these structures affect the probable mineralization zones.

Sep 22, 2022

By Eugene A. Lang

Mr. Chairman, ladies and gentlemen. As a member of the uranium and coal producing community, I am pleased to participate in a session dedicated to a look at these and other mineral markets.(title slide) before sharing some of my thoughts with you, let me tell you a little bit about rocky mountain energy company. It was established as a subsidiary of union pacific corporation in 1971 with responsibility for coal, uranium, and industrial minerals. We participate in four coal mining operations and a uranium mine and mill all in Wyoming, and an aggregate and an abrasive operation in Utah.

Jan 1, 1984

By E. C. Watkins

The fiber glass industry is an industry that. hopefully is still in its infancy and far from a mature business. Fiber glass, as will be discussed in this paper, deals with continuous strand glass as used in the textile laminate and reinforced plastics industries. More specifically, we are speaking of glass used for printed circuit boards, tapes, paper, cloth, pipes, tanks, boats, recreational equipment, roofing shingles, and automotive applications. Compared to the flat, container and decorative glass industries, we are very young. The early patents on fiber glass applications were issued in the 1930's. The type of glass most commonly used in the world and that discussed in this paper is designated as "E" glass. This is a boro-silicate type glass having specific chemical and electrical resistance and low thermal expansion properties.

Jan 1, 1986

By D. M. Hausen

A quantitative x-ray diffraction method has been developed for the analysis of alteration minerals in wallrock. Alteration data are plotted and contoured (analogous to geochemical data). Alteration trends outlined by this technique correlate closely with geochemical anomalies, and in some cases attend well beyond the perimeter of anomalous base metal values. "Monomineralic contouring," applied originally to porphyry-type mineralization, has been extended to other types of mineralization, including volcanogenic massive sulfide deposits. Equipment and techniques used in the quantitative measurement of alteration mineralogy are discussed.

Jan 1, 1978

By Dolf Vos

The balling section of the pelletizing plant at Hoogovens IJmuiden consists of 7 balling drums. Each with an average capacity of 100 tons of green pellets per hour. The balling drums are equipped with rotating scrapers and water-spraying systems. The scrapers are installed in order to restrict the growth of the race to a certain thickness. The spraying system is used to adjust the desired value of the moisture-content of the rewetted ground ore, the pellets and the race. The desired value is the value by which the balling- process is stable, good pellets are formed and surge occurs within certain limits. In October 1980 the construction of one of the balling drums has been modified. The rotating scraper was removed and the inner wall of the drum was supplied with a rubber-lining. In 1982 a second balling drum has been rubber- lined. At the same time the Tyler vibrating screen of this balling circuit has been replaced by a roller(bed)screen. By the end of 1983 all 7 balling circuits will be equipped with rubber-lined drums in combination with roller(bed)screens. The combination of these two modifications will improve the quality and the screen analysis of the green pellets, moreover resulting in savings on energy- and maintenance costs. This paper describes the influence of a rubber- lining on the balling process and the green pellet quality by carrying out in-plant testruns in November/December 1980. The testrun results have been compared with the results of a not modified balling drum.

Jan 1, 1983

By N. Kuyucak

While Acid Rock Drainage (ARD) occurs naturally, its management poses challenges especially at the decommissioned sites. Two passive systems were designed and implemented at two different decommissioned mining sites in Canada in order to treat the seepage with ARD characteristics. One seep originating from a reclaimed tailings pond was neutral mine drainage (NMD) containing circumneutral pH and dissolved metals (e.g., nickel, zinc) in elevated concentrations. The other ARD from a tailings stack showed net acid drainage characteristics with low pH and higher metal concentrations than regulated limits. Due to the different ARD characteristics occurring at each site, different types of treatment systems were designed and implemented. Both sites experience extreme winter conditions. The NMD has been treated mainly by limestone drain and aerobic systems since 1997. The acid ARD has been treated by a system consisting of an anaerobic sulfate reducing bacteria (SRB) cell, an aerobic cell and a limestone filter since 2004. As this site has no access roads, space, or power, a significant capital cost as well as sludge disposal/storage requirements would have been required to institute a chemical (active) treatment system. Both systems have been successfully treating seepage and producing a water quality year round that could comply with regulated objectives.

Jan 1, 2010

By J. M. Bray, R. R. H. Cohen, P. Kiousis, S. R. Al-Abed

"INTRODUCTION Conventional tailing storage and management practices typically utilize engineered facilities, such as ring dikes and valley impoundments. To reduce the environmental costs associated with disposing of mine wastes in tailing storage facilities (TSFs), several beneficial re-use strategies have been developed over the years. For example, thickened tailings have been used for paste backfill. It is common for tails to comprise up to 60% of the material’s total weight and it has been estimated that TSF volumes can be reduced by 60% when using this strategy, (Benzaazoua, et al. 2004). Other beneficial re-use strategies have produced unpaved temporary access roads, hot and cold asphalt, chip seals, self-compacting concrete, and golf course sand traps. This project sampled mine tailings from two different TSFs in Colorado and produced structural concrete that could potentially be used for commercial foundations, sidewalks, and paved roads. The tailings were substituted for the fine aggregates typically found in conventional concrete. The two main objectives of this study were to investigate the structural integrity of the produced concrete samples and the leaching of heavy metals from the resulting concrete. The ratio of tailings to fine aggregate (T/FA) was carefully studied to find if there was a correlation between the substitution rate and the structural integrity. The potential maximum substitution rate was also investigated for the produced concrete specimens. The potential of leaching mining impacted water (MIW) was evaluated by comparing the leachability of the raw mine tailings to the encapsulated tailings by using standard shake extraction prediction tests. MATERIAL AND METHODS Materials The four components that make up the concrete mix design for this project are: cement, coarse aggregate (gravel), fine aggregate (sand and mine tailings), and water. The type I/II ordinary Portland cement (OPC), gravel, and sand came from local cement and concrete companies in Denver, Colorado. Mine tailings were collected from two different TSFs in the Rocky Mountain Region, where Pride of the West TSF in Silverton, CO will be denoted as Site A. The primary metals of interest at the mill site are gold, silver, lead, copper, and zinc. The location of Site B will not be mentioned in this report due to confidentiality agreements with the mining company"

Jan 1, 2016

By Allen Latham

It started' in 1936 when some Dutch adventurers wanted to scale the highest mountain in the South Pacific. Quite by accident, they discovered the Ertsberg, a contact deposit of magnetite laced with chalcopyrite, in a high mountain valley where it had been gouged at by glaciers and finally left as a solitary pillar for its discovery by a geologist who lent purpose to the expedition, Dr. J.J. Dozy. By the-.time a report was published describing the deposit, war had hit the Netherlands. Perhaps again by accident, the report was uncovered in 1959 by the East Borneo Company. At this point, Freeport entered the scene through its vice president for exploration, Forbes Wilson. During the course of a meeting on laterite prospects, the Ertsberg was introduced and he put the wheels into motion for Freeport to join in its exploration. You might, at this point, ask yourself whether you or your company would have taken on a venture to look at a reportedly large high grade copper outcrop in New Guinea, an unexplored land known best for its inhospitable climate, terrain and head-hunters. I heard the chief executive of one large mining company comment sometime back that neither he nor his company would have gotten involved. I won't attempt to describe the trials of the initial exploration expedition that passed through dense-man grove swamps, tropical jungle and across jagged mountains a distance of some 200 miles to get to the Ertsberg in 1960. It should be chronicled by its participants - Forbes Wilson, Del Flint, and John Bowenkamp. Needless to say, the participants relish the experience but wouldn't be among those volunteering for a return engagement. As a result, the Ertsberg changed from a reported outcrop to a mineral deposit containing an estimated 13 million tons with systematic surface sampling indicating a copper grade of over four percent. Moreover, the deposit extended to an indeterminate depth with the possibility of doubling or tripling. reserves well within reason.

Jan 1, 1971

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

Accurately estimating load distributions and ground responses around underground openings plays a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses, both empirical and numerical. In this study, the numerical modeling approach recently developed at West Virginia University, which is based on the modeling approach developed by the National Institute for Occupational Safety and Health (NIOSH), is investigated using the finite difference software FLAC3D. The model includes the longwall panels, the adjacent chain pillar systems, and the different stratigraphic layers of the overburden. Using the 3D model, changes in loading conditions and deformations on the areas of interest, induced by an approaching longwall face, can be examined. This paper details the 3D modeling of a longwall panel utilizing this approach, and the verification of the results against field observations. The studied panel was 360 m wide with a 3-entry chain pillar system and about a 160-m average overburden depth around the studied area. The overburden strata consist of alternating layers of shale, sandstone, and limestone. The FLAC3D results were compared against field measurements from the mine site. The stress change values measured in the chain pillars were comparable with the modeling results. The model also replicated the surface subsidence profile obtained from field measurements fairly well. Overall, the 3D modeling approach was found to be successful for the case study longwall panel.

Sep 23, 2020

By P. R. Pereira

This paper presents a comparison between the simulations of a semi-empirical model and a theoretical model for the prediction of radial stress in rock. The results of the simulations were compared to the results of a field test. The comparison of the radial stress predictions shows that in the semi-empirical model use of the plane wave approximation as the basis for the prediction of the radial stress provides a much better result than the theoretical model. The theoretical model includes the correct elastic wave geometry and theory but fails twice, firstly by considering the charge as a point (unit) energy source therefore; and secondly by using a Delta function with a very sharp rise and decay time to simulate, with no distinction between non-linear and linear zones, the attenuation of the energy per unit volume at the shock wave front as the wave moves away from the borehole. The results of the semi-empirical model were within the same order of magnitude as the results from the field test whereas only one result from the theoretical model came close to the result of the field test. However, even this closer result for the theoretical should be taken with caution as there was no measurement in the field test made at this distance from the borehole. Finally, because of its potential portability, convenience, and cost-effectiveness the theoretical model can be a most valuable tool for mining and civil construction operators in the early design of blasting rounds and of the mining operation itself.

Jan 1, 1993

By Brajendra Mishra, Himanshu Tanvar

Niobium and tantalum extraction industries heavily depend on fluoride chemistry for metal oxide production. This study concentrates on developing a fluoride-free approach utilizing alkali treatment for selective dissolution of niobium and tantalum phases. The application of microwave heating in the alkali treatment of columbite significantly reduced the processing time, providing a higher reaction rate and recovery than conventional heating. A short duration of microwave exposure (6 min) elevated the sample temperature to more than 900 °C, resulting in the rapid formation of water-soluble niobium and tantalum complex. Metal recovery from the solution was attempted through direct precipitation using guanidine carbonate as the precipitating agent, resulting in a mixed oxide product with > 90% purity. On the other hand, solvent extraction was also attempted using methyltrioctylammonium chloride as an extractant, providing a niobium oxide and tantalum-rich mixed oxide with > 98% purity as the final product.

Mar 23, 2024

By A. P. Cook

Methane Rating has been developed from a need, in South Africa, for quick and simple measurement of coal face methane characteristics. It employs proven existing direct measurement methods, adapted specifically for rapidly advancing coal face conditions, to deal with the short term high release rates encountered during continuous miner coal cutting. The Rating is a comparative value, relative to the normal or average conditions encountered within a maintained data base. The seam gas content and the initial emission rate are plotted against each other on a graph, where they are compared with the average conditions to obtain the rating. The higher the seam gas content, and the higher the initial methane release rate, then the higher the Methane Rating, on a scale of 1 to 4. Methane being released from a newly mined coal sample is measured once underground, from a sealed gas-tight canister. The sample is returned, still sealed, to surface and milled to rapidly release the remaining methane. It is later intended that the milling process is also completed underground. Applications include the identification of changing methane conditions, outburst prone conditions, methane emission against advance, and mining in devolatilised coal.

Jan 1, 1998

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By M. Akser

Ilmenite, rutile, and zircon deposits of commercial importance have not been reported to-date from Turkey. However, information from recent reconnaissance activities indicates the possibility of an economically viable heavy-mineral deposit along the Black Sea coast of Turkey in the vicinity of Ormanli, northwest of Istanbul. Consequently beach and sand dune samples were collected from that area for additional analysis. Laboratory methodologies, designed to simulate standard industrial heavy-mineral plant practices, were used to analyze and evaluate the samples. Based on the analyses, and current market needs, none of the deposits in the Ormanli area qualify as a commercial heavy-mineral deposit.

Jan 1, 1995

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010