Search Documents

By Robert A. Blake

Introduction Sulfide copper, zinc and iron concentrates are recovered in the 5000 ton per day flotation plant operated by Cities Service Company at Copperhill, Tennessee. The heavy-sulphide ore is first ground to 50 pct. minus 200 mesh and a bulk concentrate floated. The bulk concentrate, over 60 pct. of the ore weight, is reground to 72 pct. minus 200 mesh and then treated in a selective flotation circuit to recover copper and zinc concentrates. The tailing of selective float is the iron sulphide material source for the manufacture of sulfuric acid and iron sinter. The valuable minerals in the ore are chalcopyrite, marmatitic sphalerite, pyrite, and pyrrhotite. A typical mineralogical analysis will be found in table 1. A typical material flowsheet will be found in figure 1. Shown in the flowsheet are a scavenger float on the bulk rougher tailing and a copper-talc separation unit. At times a lead-copper separation circuit has been run.

Jan 1, 1971

By S. Khoshjavan

Separation of refractory rock phosphate (P2O5 = 11.5%) from the Dalir area, Iran, containing quartz, calcite and other impurities, by calcination and flotation processes has been successfully used to upgrade the phosphate values. Petrographic studies of this ore showed that collophanite was the major phosphate mineral and the main gangue minerals were calcite, dolomite and quartz. The results of characterization studies showed that the liberation degree of apatite occurred below the average grain size of 140 µm. Preliminary flotation tests were used to process the phosphate samples. Results of preliminary flotation tests showed that they don?t contain any desirable efficiency (grade or recovery) of P2O5. Calcination was the best process for preconcentration of this ore. In the desliming stage, about 14.4% of total P2O5 was removed. Encouraging concentrate grades were obtained after flotation with anionic and cationic flotation, successively. The reagent schemes that have been used in this study consisted of COCO-amine acetate and fatty acid as silicate and apatite collectors, respectively, as well as fuel oil and anionic poly acryl amid as promoter collectors. The optimum pH values for direct and reverse flotations of phosphate were 11 and 6, respectively. Experiments conducted using d80=140 µm deslimed fractions has yielded an acceptable grade of more than 30% P2O5 with a recovery of more than 62%. Finally, a laboratory flowsheet for the processing of Dalir refractory phosphate ore has been proposed.

Jan 1, 2011

By J. Y. Lee, J. Kang

"A selective chlorination process using cuprous chloride (CuCl) was investigated for producing high-grade chalcocite (Cu2S) from chalcopyrite (CuFeS2) feed. The chalcopyrite feed was reacted with CuCl in the presence or absence of sulfur (S) at temperatures between 900 and 1,100 K for five hours under an argon gas atmosphere. The experimental results indicate that iron (Fe) was selectively removed from the chalcopyrite feed as ferrous chloride (FeCl2) at 1,100K and the mass percentage of Fe thus decreased from 31.5 percent in the feed to less than 0.05 percent in the residue, under certain conditions. As a result, high-grade Cu2S was obtained from chalcopyrite in a single step. This new selective chlorination of chalcopyrite using CuCl as a chlorinating agent is therefore feasible for producing high-grade Cu2S.IntroductionCurrently, blister copper (Cu) is commercially produced from sulfide ores by pyrometallurgical methods. These methods entail matte smelting and converting, with the removal of iron (Fe) and sulfur (S) as slag — mainly Fe2SiO4 — and sulfur dioxide (SO2) gas, respectively.In the pyrometallurgical method, as shown in Fig. 1 (Schlesinger et al., 2011), Fe is removed through two steps at high temperatures of around 1,500 K to reduce the loss of Cu during slag formation. However, the slag still contains 1 to 8 percent Cu. Therefore, Cu in the slag is recovered by slag treatment processes, after which the concentration of Cu in the slag decreases to around 0.4 to 1.3 percent. Although Cu is recovered, the slag that had undergone the treatment processes is difficult to use as a feedstock for ironmaking owing to the small amount of Cu remaining in the slag (Schlesinger et al., 2011).In addition, large amounts of SO2 gas are generated by the oxidation of S in the current Cu production process. The SO2 gas generated is captured and used to produce sulfuric acid (H2SO4). However, despite the development of SO2 gas-capture technologies, the emission of SO2 gas is still a problem in terms of environmental considerations.Several studies had been carried out in the past to overcome the drawbacks of the current process. The extraction of Cu from sulfide ores using a chlorination process is one alternative that had been investigated by several researchers. Most chlorination processes used chlorine gas (Cl2) as a chlorinating agent at temperatures between 573 and 1,023 K under an inert atmosphere (Donaldson and Kershner, 1962; Olsen et al., 1973; Kumar, Li and Warren, 1985, 1987; Kanari et al., 1999; Kanari, Gaballah and Allain, 2001)."

Jan 1, 2017

By Jr. Raleigh

In a cooperative agreement between the U.S. Bureau of Mines and the U.S. Department of Energy, laboratory column-flotation tests were conducted to evaluate fluorosurfactants as selective fine coal flotation collectors. A Middle Kittaning seam coal responded to flotation with both anionic and nonionic fluorosurfactants. These fluorosurfactants were no more selective than MIBC alone. However, for increasing coal yields, nonionic fluorosurfactant systems did not increase total sulfur and ash contents as sharply as MIBC systems. Flotation selectivity also improved slightly when a combined anionic fluorosurfactant-MIBC system was used in acidic pulps (pH < 3.6). While the fluorosurfactants examined will not likely have direct application in current coal flotation practice, other fluorosurfactant systems could eventually prove beneficial for floating fine coals.

Jan 1, 1990

By Gregory Rumbaugh, Christopher Mark

Recent pillar collapses have caused five large airblasts in underground U.S. limestone mines. One of these events injured three miners, but all of them put many other miners at risk. To better understand the hazards, Mine Safety and Health Administration (MSHA) conducted a comprehensive review of the international literature on airblasts. More than 40 airblast cases have been documented, in a wide variety of minerals. Experience shows that miners that are in the direct path of the air as it moves towards the mine exits are at the greatest risk. The paper describes a risk management methodology that can be used to evaluate the level of hazard throughout the mine and aid in the selection of controls to reduce the risk. The paper concludes with a detailed case history of an actual pillar collapse and airblast.

By D. G. Hartley

The major copper loss at Mount Lyell is in the coarsest particles presented to flotation. An analysis of data collected from the five primary and six secondary ball mill circuits showed that grinding was limited by low breakage rates in secondary mills, possibly due to oversize balls. For 5 months, the make-up ball size for one secondary mill was reduced from 50 to 30 mm. Frequent steady-state tests indicated that overall average breakage rates could be increased by about 70% using smaller balls. A mathematical simulation of the whole circuit with increased breakage rates showed that the resultant finer grind was likely to improve copper recoveries by about 22.

Jan 1, 1981

By W. Norman Sims

A number of forces are at work that are now having an influence on coal handling systems. Changes are occurring and will be occurring at an increasing rate during the next few years. 1. Environmental concerns will dictate that dust pollution and spontaneous combustion and its resulting problems be rigidly controlled. 2. Slurry pipelines will be a reality despite the opposition of the railroads because they are economical and make good business sense. Artifical roadblocks can only survive for a limited time. 3. Coal is now and will remain the most economic fuel, particularly for power generation. This is true in most of the developed nations not just the United States. Increase in demand requires a close inspection of transportation systems. 4. A projected major increase in the export of U.S. coals may never occur without major port developments not the least of which will be the ability to accommodate large ships without demurrage time now affecting such shipments at U.S. Ports.

Jan 1, 1982

By D. D. Runnells

In order to establish meaningful remediation goals and monitoring programs in areas disturbed by mining, it is desirable to determine the natural metals concentrations that existed in the area prior to mining. At Iron Mountain, California, several natural sources exist for acid drainage and loading of metals to Slickrock and Boulder Creeks. This paper describes methods to determine the contribution of copper and zinc to groundwater and surface water from those sources, including natural gossan rock outcrops, mineralized bedrock, and colluvial materials. Methods used include evaluation of: 1) historical information, 2) literature values of unmined, mineralized areas, 3) analyses of water from monitoring wells, 4) leaching studies, 5) statistical analysis, 6) isotopic studies, and 7) identification of background by elimination of mining sources. Results from this natural background determination show that Boulder Creek and Slickrock Creek carried elevated concentrations and loads of copper and zinc prior to mining activities. With repeated rinsing of reclaimed and remediated mine materials by rainfall, there will be a diminishing contribution from residual waste rock and tailings at Iron Mountain, and natural background will become an increasingly larger proportion of the total load.

Jan 1, 1999

By A. E. Jack Swanson, Brian P. Micke

INTRODUCTION Nevada Goldfields began underground mining development at the Kingston Project in September, 1986, followed by mill start-up in March, 1987. The first gold pour in April followed three years of preparatory work in establishing a North American operational base for the production of precious metals by Golconda Minerals N.L., an Australian mining firm. GENERAL CORPORATE BACKGROUND The Golconda Group of companies was established in early 1983 in Australia. It began operations by successfully retreating tailings at several old gold mining sites throughout Australia. With the limited reserves available for tailings retreatment, Golconda began to look toward the future by conducting a gold exploration program in Australia. However, the continued high price of gold in Australia had limited the possibilities of acquiring good properties at a reasonable cost and consideration was given to looking outside Australia in addition to Golconda&apos;s domestic exploration activities. North America was favored because of the proven potential for substantial gold deposits, the established infrastructure which would allow for rapid and cost-effective development of new projects and the advantages of similar political and economic climates. In mid-1984, Golconda established an office in California and began an extensive study of over 100 prospects throughout the United States. Two prospects were identified as a result of this study whch showed merit; one was located at Empire, Colorado and the other at Aurora, Nevada. Negotiations were then successfully undertaken to acquire these two properties. Golconda&apos;s U.S. offices were moved to Reno, Nevada in early 1985 to facilitate management of its projects. To operate and manage these projects, a small Canadian company listed on the Vancouver Stock Exchange, Cannon Minerals, was acquired by Golconda and renamed Nevada Goldfields Corporation. The current structure of the company is shown below in Figure 1. A private placement of 2,575,000 shares of common stock at US54.00 per share was arranged by Jacksons Limited of Australia in association with W.I. Carr (U.K.) Limited of London. This placement resulted in US510.3 million being available in May, 1986 for the acquisition and initial development of the Aurora and Empire projects. While the financing was underway, project planning commenced on both the Aurora and Empire projects. The Aurora project was selected as the one to be initially developed because of its relatively advanced stage of development. The

Jan 1, 1987

By Y. H. Zhan

A new P(MAAA) latex was developed and used in separation of ultrafine apatite from calcite and silica by means of selective flocculation. The latex was found to flocculate selectively apatite from apatite/calcite and apatite/silica mixtures in the presence of sodium tripolyphosphate and sodium silicate over a pH range from 9.1 to 9.4. The separation of apatite from calcite was more selective with sodium tripolyphosphate, while the results of the separation of apatite from silica were better when sodium silicate was used. In the apatite/calcite system, 90% apatite recoveries into a concentrate containing 34% P2O5 were possible in the presence of 4 mg/l of sodium tripolyphosphate at a latex dosage of 2.2 kg/t. In the apatite/silica system, 80% of apatite could be recovered into a concentrate containing 33% P2O5 in the presence of 20 mg/l of sodium silicate at a latex dosage of 1.1 kg/t. Deposition tests were used to study the interaction between the latex and the mineral surfaces. The results revealed that deposition density of the latex on apatite was higher than on calcite; the differences between the deposition onto these two minerals were higher at pH 9.2 than at 7.2. The results point to the stronger interaction between the latex and apatite surface when compared with the latex-calcite interactions.

Jan 1, 1998

Stillwater Mining Company has an extensive history with tunnel boring machines (TBM) at the Stillwater and East Boulder underground PGM mines in Montana. The first use of a TBM was a 4 m (13 ft) diameter main beam unit at the Stillwater mine starting in 1988, where 6.4 km (4 mi) of tunnels were driven parallel to the J-M Reef orebody on four different levels. TBM?s were central to the development of the East Boulder Mine as two 4.6 m (15 ft) TBM?s drove two 5,639 m (18,500 ft) parallel tunnels to access the J-M Reef; one of these units is still in service driving a 2,591 m (8,500 ft) access West of the East Boulder mine for the Graham Creek project. For the Blitz Project, a 5.5 m (18 ft) diameter main beam unit will be utilized to drive a 6,858 m (22,500 ft) ventilation and rail haulage level East of the Stillwater mine. TBM?s have been preferred method for developing new mines and sections of the J-M reef as the geometry and geology of the Stillwater Complex allow for faster development compared to conventional methods.

Jan 1, 2012

By Nikhil Dhawan, Débora Moreira, Yogendra Pratap, Himanshu Tanvar

A glauconitic siltstone sample with a potash content of 10% is investigated as a potential potash source. The fine grain structure comprises potash bearing phases of glauconite, muscovite, and microcline. The as-received samples showed poor dissolution ~ 5%. Planetary ball milling was attempted for the dissociation of the underlying silicate structure for the potash release, and ~ 60% potash was obtained after 12-h milling. Mechanical activation (8 h, 60% NaOH) prior to heat treatment (600 °C, 30 min) was found successful in recovering more than 95%K values from glauconite. The final residue consists mainly of quartz, indicating a complete breakdown of the silicate matrix. The mechanical activation process followed is simple, adaptable, and less energyintensive compared to existing methods.

May 4, 2020

By S. J. Schatzel, J. D. Addis, V. Gangrade, L. L. Chasko, C. A. Hollerich

"A ventilation study using tracer gas was conducted at a western US coal mine. The objective of the study was to evaluate the movement of longwall face air exchanges between the face and worked-out area and to document the presence or absence of face airflow pathways between these locations. The mine operator uses a bleederless longwall ventilation system with a back return and a blowing mine ventilation system. The study was conducted on an active panel and included both underground and surface monitoring sites. The study used sulfur hexafluoride (SF6) released as a slug on the longwall face and in the front of the gob inby the face. The velocity of the tracer gas movement in the gob was 0.019 m/s (3.7 fpm). The rate of movement for the overall tracer gas slug averaged about 0.0091 m/s (1.8 fpm). A separate tracer gas test initiated with the release of SF6 into the legs of the first shield showed the existence of more than one pathway of face air in the general direction from the headgate towards the tailgate corner. Maintaining adequate ventilation air on longwall faces is important for worker safety and for the dilution of methane emitted from the face and caved gob. A more detailed characterization of longwall system air and gas movement allows a mine to better assess its ventilation design for controlling gas on the face and in the gob. INTRODUCTION During a series of stakeholder meetings, a near unanimous concern was expressed related to maintenance of effective ventilation airflow on longwall faces. There was a strong interest expressed regarding the impacts of face length and caving characteristics on the ability to maintain adequate face airflow levels. This study seeks to understand and improve a mine operator’s ability to monitor and control ventilation and methane concentrations across the longwall face by assessing airflow variations in terms of roof caving characteristics and face length. National Institute for Occupational Safety and Health (NIOSH) researchers seek to identify flow paths of ventilation airflow on longwall panels with variations in roof caving characteristics and longwall face lengths. The project research aims to develop an understanding of the role of gas dynamics in variable broken rock, interactions with ventilation airflow and methane concentrations across the longwall face area. The research also addresses continuous ventilation monitoring along the shield line to provide early detection of gas exchanges between face and gob, and thus improve a mine operator’s ability to monitor and control ventilation and methane concentrations around the face. In the context of this paper, the longwall gob refers to the pillared area behind the shields. This work reports on results from one project task to conduct field based research using a tracer gas to describe face air and gob area gas movement in a bleederless longwall ventilation system that incorporated a back return."

Jan 1, 2017

The ability to increase and maintain dragline productivity is a key mine driver for the Coal Creek Mine. The Coal Creek Mine is owned by Arch Coal Inc subsidiary Thunder Basin Coal Company; located near Gillette, WY. Coal Creek Mine overburden stripping is primarily accomplished by a BE-1570W walking dragline in combination with cast blasting and dozer assist for bench preparation. The two main variables impacting dragline performance are maintenance reliability and operator skill levels. The mine?s most recent process improvement efforts have focused on its most valuable asset - the operator. Various techniques have been used to reduce variability in the dragline operator?s digging performance. Utilization and communication of operator performance data, statistics, and video reviews have been of great value towards achieving this goal. Operators are given a chance to critique operational tendencies from a third-person point of view, and are also presented statistical feedback to support observations. From these sessions, operators gain knowledge as to what portions of the dig cycle can be improved in order to reduce cycle time and increase productivity. BACKGROUND The BE-1570W walking dragline was commissioned at Coal Creek in November 2006 after relocating from Arch of Wyoming located in southeast Wyoming. The first two years of operation the machine was performing simple side cast stripping due to the low ratio. Coal Creek Mine is a multiple seam operation with overburden thickness ranging from 24 to 140 feet. Early in 2009 the ratio increased to the point where transitioning to cast blast/extended bench stripping was necessary. The current mining conditions consist of a mixture of both stripping styles where the ratio allows. The dragline crews running the machine consist of a mixture of experience levels ranging from 30+ years to only a few years. It has been in this digging environment and slightly inexperienced personnel that the focus has been set for improvement in dragline performance.

Jan 1, 2011

By J. Fritz, V. Gangrade, J. Briton, K. M. Ajayi, M. L. Harris, G. Cole, M. Young

Mine workers using diesel-powered equipment experience the highest occupational exposure to diesel particulate matter (DPM). This problem could be aggravated in underground stone mines due to their unique ventilation challenges with the large openings for airflow. Hence, adequate ventilation in these mines requires a combination of effective ventilation planning and delivering needed air quantities using auxiliary fans and stoppings. To meet this challenge, the National Institute for Occupational Safety and Health (NIOSH) developed the Air Quantity Estimator (AQE) software as a mine planning tool to help underground mine operators estimate the air requirements necessary to dilute DPM in the main air stream to statutory levels. The major parameters required for the calculations are the engine’s horsepower, DPM emission rate, the percentage operating time, catalytic converter efficiency, and filter efficiency. In efforts to provide major updates to this software, this study describes the recent development of a revised version of the Air Quantity Estimator (AQE 2.0). With the revised version, users have access to a comprehensive database of over 40,000 pieces of equipment, can define their specific target DPM level, and can create specific equipment for a customized database, in addition to having an improved easy-to-use interface. The software output provides an estimated total airflow necessary to dilute DPM based on the projected emissions, and the user can generate a related results report. The results also provide the mine personnel with a tool to identify vehicles that are high DPM contributors and could further be used to optimize the ventilation requirement by making changes to the percentage operating time of the engine. This software provides the mine with a user-friendly tool that could help reduce the DPM exposure of workers.

Feb 1, 2023

By W. H. W. Husband

Rock salt has been mined by the solution method for many years in many countries. Attempts have been made in the past in Canada and various other countries to produce potash by the&apos; same method. However, only Kalium Chemicals Limited (1) has been successful, possibly because the conditions in Saskatchewan are the most favorable conditions to be found so far for the development of a solution mining method for potash. There are significant differences in solution mining of rock salt and solution mining of potash. First, rock salt deposits are relatively pure in respect to soluble minerals, whereas potash is never found in the pure state and contains Substantial amounts of other soluble minerals, particularly rock salt. In comparison to rock salt, much less potash is dissolved and brought to the surface for the same amount of water circulated through the orebody. The amount of water to be evaporated per unit weight of product is a major difference. Much greater amounts of water must be evaporated when producing potash and the treatment of the brine is more complicated because other dissolved salts have to be separated. Secondly, the rock salt deposits, particularly the domes, are much thicker. Bed thickness is of prime importance because it determines the yield of a well and consequently the economics of the process. Furthermore, as rock salt provides a strong roof structure, larger cavities can be developed and this prolongs the life of the rock salt well.

Jan 1, 1971

By B. T. Darnton

Gravity concentration at the Pegasus Gold Montana Tunnels Mine was initiated in late June, 1991 with the commissioning of a coarse gold scalping circuit that processes a small portion of the ball mill circulating load. The primary objective for the circuit was to reduce the risk of gold particles advancing to flotation that are too coarse to float. The secondary objective was to enhance overall gold recovery and payable gold ounces in a cost effective manner. The gravity circuit has proven itself to be a major success. The above mentioned goals have been achieved, and they have been maintained at record throughput rates that are 30% higher than when the circuit was commissioned. A number of modifications and improvements were made over the last three years which allowed the gravity circuit to keep pace with the higher tonnage, these are discussed in detail in the body of this paper. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project which will allow for an estimated 50% increase in gravity gold production, while reducing the overall unit costs of production significantly. This paper will review historical gravity circuit performance, improvements, and the current relocation and expansion project.

Jan 1, 1995

By G. R. Addie

While the cost of transporting raw phosphate matrix from a pit to a processing plant via slurry pipelines is more efficient than it could be by rail cars, conventional trucks or belt conveyors, it still amounts to many millions of dollars, and in many areas there still exists much room for improvement. By taking advantage of pipeline test data on different slurries, it is possible to reduce costs by optimizing pipeline diameters, operating velocities and slurry concentrations. Better wearing, more efficient pump designs are now available which, if applied correctly, can lead to significant savings. The authors discuss what benefits are possible in relation to the electrical operating and wear maintenance costs and go into some of the factors associated with taking advantage of these benefits, identifying what they see as being practically possible.

Jan 1, 1998

By A. W. Khair

This paper presents a strength formula for the design of coal pillars. The formula is derived from results of laboratory experiments, studying the effects of primary factors influencing the strength of the coal specimens/pillars. Five primary factors, significantly affecting the strength characteristics of the coal specimens/pillars were identified and extensive laboratory investigations were carried out. The five primary factors were namely 1) coefficient of friction between loading platens and coal specimens, 2) elastic properties of the loading platens, 3) coal specimen geometry, 4) coal specimen size, and 5) rate of loading. Four to nine levels of variation for each primary factor on the strength of coal were studied. An empirical formula, implementing the variation of the primary factors affecting the strength of coal specimens/pillars, has been developed. A comparative analysis of the results provided by this and some well known formulae is also presented.

Jan 1, 1994

By M. A. Boucher

The purpose of my presentation is threefold: a) to make you aware of what is available in Canada in terms of refractory minerals. b) indicate the mineral deposits that have potential for development. c) show the advantages of Canada as a supplier of electrical energy necessary for the production of electrofused minerals. Canada is a producer of natural refractory minerals, electrofused minerals, and synthetic refractory minerals. Several deposits also have good potential for development. The natural refractory minerals produced in Canada are shown in Table 1. The major minerals by decreasing order of importance in terms of tonnage and values are: dolomite, graphite and magnesite.

Jan 1, 1992