Search Documents

By C. M. Goodall

Solids and liquid phase residence time distribution data is reported for a laboratory column flotation cell. The effects of various physical flotation parameters on residence time distributions are reported and analyzed. A plug flow model with recycle is proposed for the froth phase and a tanks in series model for the pulp. By comparison of two and three phase residence time -distribution data it has been shown that the use of liquid residence time distribution data to predict the residence time distribution of the solids in a column is not valid.

Jan 1, 1990

By C. L. Lin

A PC image-based on-line coarse particle size analyzer has been developed to measure particle size distributions under plant situations where overlapped particles are being transported on a moving belt conveyor. Although previous testing had shown satisfactory performance of this image-based system for separated particle size measurements (the non-overlapped case), it was necessary to modify original algorithms in order to solve the overlap problem and make the system suitable for plant operations. On-site testing has been conducted at a large copper concentrator in the southwestern U.S. for further investigation of the overlap problem.

Jan 1, 1995

By J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is n practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota (a) must be covered with about 70 cm of soil material to achieve maximum production; (b) topsoil must be segregated and spread separately from subsoil; (c) potential production depends on the quality of the soil material returned; and (d) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation. Almost half the nation's cool reserves are in the Northern Great Plains underlying several million hectares of agricultural land. Social pressures to return mined land to agriculture or other productive uses have resulted in recent enactment of state and federal legislation, which is intended to restore productivity to disturbed areas. All such legislation relating to the Northern Great Plains has stipulated that useable soil material be saved and returned to mined land after spoils are smoothed. This requirement immediately raises questions as to how much soil material is needed, what criteria are important in defining useable soil material, how is the soil material to be handled in the earth-moving operations involved, and how can replaced soil material be maintained and revegetation. Scientists at the USDA Northern Great Plains Research Center at Mandan, North Dakota have conducted research on the reclamation of disturbed lands since 1970. Initially this research was designed to identify and characterize those physical and chemical properties of spoils that are most restrictive to plant growth (1). Basically, they found that any properties of spoils that reduced the efficiency of storage and utilization of the limited precipitation received adversely affected plant growth. Thus, in the Northern Plains, revegetation of mined land was found to depend upon the management of factors affecting the availability of water to plants - the same as on unmined land. After the major problems in revegetation were identified, technologies were developed to circumvent the effects of the growth-limiting factors (2). Basically two approaches were identified by which plant growth-restricting properties of spoils could be corrected: (a) various amendments (gypsum, sulfur, Fertilizers, mulches, calcium chloride, etc.) could be applied to spoils to improve their ability to conserve precipitation and provide water for plant growth; or (b) undesirable spoils could be covered with suitable soil materials to reduce or alleviate adverse effects. The latter approach appeared to be more feasible in most instances And is the approach specified in current legislation. The remainder of this paper discusses research on the use of roil materials returned to spoils and summarizes the information obtained.

Jan 1, 1978

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By CASSANDRA L. HOEBBEL, Emily J. Haas, MARGARET E. RYAN

In recent years, there has been increasing interest in the role that individual factors play in health and safety (H&S) outcomes in the mining industry. Two surveys, one measuring self-reported routine safety performance and one measuring individual perceived competence in the non-routine knowledge, skills, and abilities (KSAs) critical to emergency response, were administered to two samples of mineworkers in separate research studies over a 2-year period (N=2,020 and 696, respectively). Eight demographic items were common to both surveys and their associations with each performance outcome were tested in response to a series of exploratory research questions.

Jan 9, 2022

By Eric Sitorus, Septian Prahastudhi, Roy William, Wieda Azani

In July 2020, massive slope failure occurred in the southeast corner Grasberg open pit. This was the final episode in the breakthrough of Production Block 2 South (PB2S) of the Grasberg Block Cave to connect to the surface. This breakthrough had been rapidly evolving during the first half of 2020 and occurred as expected with no adverse impacts to safety or operations. To manage and safeguard the exposure to the workforce and operations, numerous hazards were identified and anticipated. The failure of the sill pillar between the open pit and PB2S cave was identified as the main area of interest and was closely watched during the failure process. This paper reviews the systematic approach developed to convert monitoring data into information around the collapse of the GBC PB2S cave sill pillar. The data that was interpreted consisted of micro-seismic, piezometric, ground-based radar and observational inspections. Geological structures on the boundary of the PB2S cave were clearly involved in the breakthrough process. As the cave propagation reached these structures and triggered instability, the resulting acceleration and breakdown were clearly shown by IBIS radar units associated with high movement in the slope. The focus of this paper is on the evolution of changes seen in the micro-seismic data and how it was used to understand the rapidly changing conditions of the sill pillar. The seismic parameters evaluated were event distribution, Es/Ep value, and the seismic moment tensor inversion. The changes of breakthrough indication seen in these parameters were substantiated by Shear Wave Splitting (SWS) analysis that showed a close correlation with the fractured zone above the PB2S cave as indicated by the increasing anisotropy.

Jan 1, 2022

By A. Suarez, M. Menendez, M. R. Gent, P. Riesgo

"Recent requirements to reduce thermal coal plant emissions, and ultrafine coal's tendency to produce these emissions due to its typically high ash and moisture contents have limited the use of ultrafine coal. Ultrafine coal in beneficiation plants are usually either disposed of in tailing ponds at a loss in combustible material or disposed of by blending with coarser higher-grade products, resulting in a reduction in marketed product quality. A study of the options for processing ultrafine coal, consisting of < 200 µm hydrocyclone overflow, with 38.8 percent ash content is presented here. Ultrafine coal was processed based on 200-µm sieve bend and 10-µm hydrocyclone classifications, enhanced gravity separation (EGS) and froth flotation concentration as well as combinations of these. Yield, combustible material recovery (CMR) and product humidity were evaluated as test results.Depending on the processing applied, product ash content could be reduced up to 49.7 percent, and up to 95.8 percent CMR of the actual run of mill feed could be attained. All of the processing options analyzed could reduce produced thermal electric plant emissions due to ash and moisture from 22 to 38 percent of the actual unprocessed ultrafine coal product.Froth flotation was found to be the optimal process, yielding a product with the lowest ash content attained of 19.5 percent and CMR of 92.3 percent. Being the most versatile of the processes evaluated, it is capable of producing coal with varied ash contents but is subject to potential variations in coal flotability. The most complicated of the processing options, a combined sieve bend recovery of the > 200 µm fraction and EGS processing of the 10 to 200 µm fraction was found to be the next best option, attaining a combined 90.1 percent CMR and 25.0 percent ash content. IntroductionMunicipal, regional and national objectives to reduce fossil fuel combustion emissions and their effects on air quality and global weather changes are affecting thermal electric plant operations. Plans and regulations such as President Obama's Clean Power Plan (U.S. Environmental Protection Agency, 2015), the European Directive 2010/75/EU (European Commission, 2010) and China’s proposed Enhanced Actions on Climate Change (Wei, 2015) are of major significance to thermal electric plant operations. Although thermal plant efficiencies depend in large part on the losses of heat by plant components, the ash and humidity contents of thermal coal invariably reduce plant efficiencies and increase emissions of carbon dioxide (CO2), nitrogen oxides (NOx) and dust.Any noncombustible material present in thermal coal will result in higher CO2 emissions per unit of energy produced. Since no particle emission control can be totally effective, it is to be anticipated that any reduction in coal ash content will also result in reduced particle emissions. Kurose, Ikeda and Makino (2001) reported that NOx emissions also increase with coal ash content. The effect of coal moisture content during combustion is complex. Kurose, Ikeda and Makino (2001) showed that an increase in coal moisture content significantly reduces thermal NOx to total NOx production, and Bosoaga et al. (2006) showed that it tends to reduce NOx emissions. Since the humidity, pyrite and ash content of thermal coals directly affect thermal electric plant efficiencies and emissions, minimizing these factors should facilitate, at least in part, compliance with thermal electric plant emission limits. This, in turn, would affect the specifications and prices of the coal preparation plant products."

Jan 1, 2016

By A. G. Fonseca

The effects of coal cleaning, coal combustion and flue gas particulate removal systems on the partitioning of 12 trace elements were investigated. This study was prepared to help document the fate of trace elements in modern coal preparation plants and coal-fired utility boilers. The coal cleaning data were obtained from several coal preparation plant operations. The CONSOL 1. 5 MM Btu/hr pilot combustion and electrostatic precipitator (particulate removal system) test facility was used to develop the combustion systems data. A comparison with the very limited amount of published data from utility boilers is presented.

Jan 1, 1993

By Yongsik Jeong, Kwangmin Kim

Conventional tailings slurry contains a significant amount of water, and water management is key to ensuring the stability of a tailings storage facility (TSF). Simply reducing the water content in the slurry before discharging it from the mill could be an effective way to improve TSF water management. This study investigated the potential for using an environmentally friendly polymer as a new drag reduction agent (DRA) to reduce frictional pressure loss and also conserve water. It entailed conducting pipe loop tests to assess the polymer’s effect on pressure loss in tailings flow and then applying the test results to validate a numerical model using computational fluid dynamics (CFD). The model was also used to determine the polymer’s optimal concentrations at given solid concentrations and flow rates, its effect on energy efficiency for tailings transportation, and its potential for saving water. A case study for a mid-sized, hard-rock mine with a throughput of 50,000 t/day found that the solid concentration could be increased from 30 to 45% with no pressure loss by applying 1996 m3 of the polymer per day. Adding the polymer also resulted in water savings of 57,552 m3/day. The results of this study demonstrated the potential for using the new DRA not only to improve TSF stability but also to save water.

Jun 29, 2020

By T. H. Combs

Increased productivity in the U.S. underground coal industry has taxed pre-existing conveyor belt haulage systems. The usual remedies are costly and can disrupt production. A reduction in the belt feeder discharge rate on mobile haulage sections results in more uniform loading and reduces the spillage vulnerability. An investigation is made to determine the effect, if any, on shuttle car discharge time arising from lower feeder discharge rates. A five-section, underground mine is visualized, and belt spillage is introduced. The sectional feeder discharge rate is progressively lowered until spillage is precluded. At each level, the simulated spillage is measured and compared to the loss in face production. Methods of predicting the loss in face production from lower feeder discharge rates are discussed.

Jan 1, 1993

By Thomas A. Mekelburg

Due to a tight ash constraint on the clean coal product and difficult middlings washability characteristics, a considerable amount of coal was being lost in the jig middlings at the Monterey No. 2 Mine. An investigation was conducted into circuitry to recover this lost coal with minimal effect on the total clean coal ash. A reverse two-stage hydrocyclone system cleaning at low specific gravities was selected. This system is currently recovering approximately 5.8 kg/s (23 tph) of 11.5% to 12.5% ash coal. The specific gravity of separation for the system is about 1.5 and the probable error is 0.13.

Jan 1, 1984

By J. Diao

In order to understand the flotation kinetic behavior of coal and associated mineral matter, a detailed investigation was conducted in a 2-liter Denver flotation cell using three high sulfur coals at three feed sizes, minus 28. 100 and 200 mesh. Subsequently. the flotation products were sieved into different size fractions and analyzed for their ash and pyritic sulfur content in order to delineate the effect of particle size on the rate at which each constituent floats. The results were tested with several different flotation kinetic models and the best model for coal was then chosen. The flotation rate constant and the ultimate recovery calculated from a kinetic model were used to delineate the effect of particle size, collector (dodecane) and frother (MIBC) dosages on the flotation kinetics of coal, ash and pyrite.

Jan 1, 1992

By F. F. Peng

For a given flotation system, the rate-controlling step in fine coal flotation can be the attachment of bubble to the fine coal particles. The probability of attachment depends upon the surface characteristics and the collector adsorption on the coal particle surfaces. Thus, to further improve the flotation rate and selectivity is to alter the distribution of hydrophobicity on coal particles efficiently by applying the effective means of collector dispersion. In order to enhance the combustible recovery and selectivity of fine coal flotation, and lower the amount of collector used in the fine coal flotation processes, four modes collector dispersion/addition techniques are tested. They are direct liquid addition in pulp (mechanical agitation), ultrasonic energy dispersed collector into pulp, atomized collector into pulp and gasified collector transported by air and formation of collector-air bubbles in pulp. The effect of four collector dispersion/addition methods on the floatability of -600 µ m (-30 mesh US sieve) coal samples from four ranks of coals were studied. The ultrasonic energy dispersed collector and atomized collector flotation processes enhance flotation yield and most significantly improve the kinetics of fine coal flotation. The gasified flotation process can increase the selectivity of separation and decrease the collector consumption due to starvation flotation is achieved in this process. The flotation efficiency of gasified collector process is as high as that of conventional flotation. It is because that the effect of the decrease in the combustible recovery is offset by the increase of selectivity. In addition to flotation experiments, induction times of bubble attachment to the bed of fine coal particles for four ranks of coals are measured.

Jan 1, 1992

By L. Adler

The valuable Maximum Utilization Factor (MUF) concept has been extended to other rotating excavators beyond stripping shovels and draglines. In this concept the boom reach and bucket capacity are multiplied to get an MUF, then normalized by dividing by the equipment weight. Statistical analyses were applied to the remaining shovels (hydraulic and cable), draglines, and backhoes. Positive correlations were found. Stripping shovels and draglines were also re-examined. The results provide an estimate of equipment diggability and encourage versatility by the interchange of the boom and the bucket. The concept further clarifies the existing equipment classification by delineating general excavating, loading, and stripping kinds. The results also forecast trends, and noted innovative advances and possible retrogression. Extension to other boom excavators, such as front-end loaders is recommended. The MUF concept provides one of the few indices of gross external characteristics available to the engineer-user of equipment.

Jan 1, 1990

By K. L. Gabby

Since mercury is chemically similar to silver, it tends to dissolve along with the silver and gold during cyanide leaching. Ultimately mercury is recovered along with the silver as mercury/silver/gold amalgam which requires retorting to remove the mercury prior to refining the silver and gold. A possible approach to separating mercury from silver and gold in cyanide leach solutions is to take advantage of the replacement reaction between [Hg(CN)4]2- and Ag2S, which results in precipitation of mercury as HgS while dissolving silver as [Ag(CN)2]-. Results are presented demonstrating that mercury can be removed from cyanide solutions with high effectiveness, while, at the same time, recovering additional silver in solution. Initial experiments with static flasks in the laboratory showed a high degree of mercury removal could be achieved. Results using actual metallurgical plant products in bottle roll tests indicate the process works on a larger scale, but also results in significant gold losses if the solution being treated has high gold levels, such as carbon stripping pregnant eluent solution.

Feb 23, 2014

Lignite is a kind of easy-to-slime and low rank coal. It is hard to be separated by the conventional wet coal beneficiation technologies. Meanwhile, in recent decades, a large amount of fine coal (-6 mm) is generated as the mechanized mining technology has been progressively deployed in coal sector, which causes a great difficult for lignite beneficiation and upgrading due to lack of efficient technology available. In this paper, a vibrated gas-fluidized bed was used to separate the -6 mm fine lignite particles. Separation experiments of -6+3 mm and -3+1 mm lignite were carried out in a laboratory-scale vibrated gas-fluidized bed. The effects of several parameters including the superficial air velocity, vibration intensity, bed height and exterior moisture content on the separation performance were experimentally studied. The results show that the optimal separation performance was achieved when the superficial air velocity is 0.3, the vibration intensity is 1.4, the bed height is 50 mm, the exterior moisture content is below 4% (-6+3 mm) and 2% (-3+1 mm). And the probably error E values of -6+3 mm and -3+1 mm size fraction of lignite are 0.202 and 0.225 respectively. The results indicate that a vibrated gas-fluidized bed can provide an effective solution for -6 mm lignite separation.

Feb 23, 2014

By J. F. Colinet, W. R. Reed, J. D. Potts

Dust surveys were conducted at six underground coal mines to determine if deep-cutting practices expose face workers to higher levels of respirable dust. The surveyed mines were able to successfully mine deep cuts without significantly increasing the dust exposures of face workers. In general, all of the selected mines exercised good dust control practices by maintaining water sprays, scrubber airflows, proper curtain setback distances and providing sufficient airflow to the active faces. For exhausting face ventilation, field data indicate that scrubber airflow is the most important factor for controlling dust. Data collected for this study indicate that 20-mesh screens should be cleaned for every 12.2 m (40 ft) of advance, because 22% of the deep cuts surveyed for this study experienced a 20% to 35% decrease in scrubber airflow over the course of the cut. For blowing face ventilation, field data and past research indicate that dust control is aided by maintaining a proper curtain-to-scrubber airflow ratio of 1.0 (measured before scrubber activation), as well as a curtain setback distance that allows the miner operator to stand at the mouth of the curtain for the entire cut. Dust levels on the bolting faces did not appear to be affected by the longer cycles associated with deep-cut mining when good ventilation practices were used.

Jan 1, 2011

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By J. P. McKinney

A mathematical model is presented for the electrokinetic dewatering of suspensions of phosphatic clays. The modeling approach couples a boundary-element model for solution of Laplace?s equation to a recently developed constitutive equation that relates the change in solids content with applied electric field and time. The observation that the electric field controls both the maximum solids content achievable and the time required to reach that value is shown to severely constrain the application of electrokinetic dewatering strategies to an entire clay settling area. The approach, however, may be feasible for implementation as part of a continuous plant process.

Jan 1, 2011

By J. G. Groppo

Froth flotation technique is an effective and efficient process for recovering of ultra-fine (minus 74 pm) clean coal. Economical dewatering of an ultra-fine clean coal product to a 20 percent level moisture will be an important step in successful implementation of the advanced cleaning processes. This study is a step in the Department of Energy&apos;s program to show that ultra-clean coal could be effectively dewatered to 20 percent or lower moisture using either conventional or advanced dewatering techniques. The main focus of the pilot plant study was on proof-of-concept testing of a dewatering technique for a fine clean coal product. The coal industry is reluctant to use the advanced fine coal recovery technology due to the non-availability of an economical dewatering process.

Jan 1, 1997