Search Documents

By J. Alatalo

Autogenous grinding is a process of reducing the particle size distribution of an extracted ore by using the ore itself as the grinding media. It is a process that is difficult to control and there is a lack of knowledge of the events occurring inside the mill. To find out more about how the mill behaves under different processing conditions, a full factorial test was performed with iron ore in a pilot-scale pebble mill at the LKAB R&D facility in Malmberget. To complement this work, a strain gauge detector was embedded in one of the mill?s rubber lifters, the Metso Minerals continuous charge measurement (CCM) system, and was used to get more information about the charge dynamics. The data from the experiments has been analyzed. For production purposes, an increase in the number of particles smaller than 45 µm can be regarded as a probable increase in the production rate. The analysis shows that there will be an increase in fines at 65% of critical speed, especially when the mill is 45% full. This setting will also increase the power consumption, but improves the grindability of the ore even more. The deflection of the lifters is smaller for lower critical speeds. A higher degree of filling also gives a smaller toe angle and a higher shoulder angle as expected.

Nov 1, 2011

By Madan M. Singh

It is estimated that through 1975, there were 1.69x109 m2 (418 000 acres) of urban land threatened by potential subsidence due to mining with a value of over $12 billion (19;3 dollars; USBM, 1979). With increased coal production to meet the energy needs of the nation, both these figures may be expected to increase. Hence greater attention to controlling surface damage due to subsidence is merited. In fact, the Surface `lining Control and Reclamation Act of 1977 (SMCRA) (Public Law 95-87) mandates that underground coal mining operators "adopt measures consistent with known technology in order to prevent subsidence causing material damage to the extent technologically and economically feasible, maximize mine stability, and maintain the value and reasonably foreseeable use of such surface lands, ..." The term "subsidence," as used in this paper, implies the total phenomenon of surface effects associated with the mining of minerals, and not only vertical displacement of the surface as is sometimes inferred in the literature.

Jan 1, 1984

By R. B. Elver

The St Lawrence Seaway, a deep-water canal system between Montreal and Lake Ontario, was opened for navigation on April 25, 1959. Prior to the opening of the new Seaway, small boats known as canalers and a few deep-sea carriers, primarily from Norway since World War II, were the only ships able to journey past Montreal into Lake Ontario through the old Canadian St. Lawrence canal system. Thus it was necessary for many tons of bulk and general cargo to be shipped all-rail to and from Atlantic ports or to be transhipped to and from canalers. With the opening of the new Seaway, large Great Lakes bulk carriers and a much larger percentage of the world's shipping fleet are now able to sail directly from the sea to the heart of industrial North America. In this paper, the historical events leading up to the construction of the Seaway and the physical nature of the Great Lakes transportation system are briefly reviewed. Following this, an attempt is made to evaluate the effects of the new Seaway on Canada's mineral industry. Because the Seaway has been in operation for only one season, this paper must be considered only an interim report. Because of the importance of the Seaway to iron ore, this commodity will be dealt with in detail, although the effect on other mineral commodities such as coal, petroleum, nonferrous ores, iron and steel will be mentioned. At this time the author wishes to thank the various company and government officials who provided both factual information and critical opinions.

Jan 1, 1960

By Ellen Amoako Afful, Michael Moats, Guang Xu, Ashish Kakoria

Electrowinning and solvent extraction are crucial steps in the production of high-purity copper. However, safety concerns have been raised regarding the acid mist generated from the electrowinning process. The mist generated results in health risks to workers and damage to machinery and infrastructure. Currently, chemicals and pellets are used to control acid mist. However, the effectiveness of these controls may vary depending on the type of organic solvent used in the solvent extraction process, which can influence the generation of acid mist. This study aims to evaluate the impacts of organic solvents and surfactants on acid mist suppression. In this study, an electrolyte is contacted with organic solvents to simulate the solvent extraction. The electrolyte is dosed with 20 mg/L of surfactant at each contact. Acid mist testing is performed on the electrolyte separated from the organic phase at the end of the solvent extraction step. The mist collected is analyzed to determine the level of acid mist generated. The results of this study indicate that organic solvents and surfactants showed significant acid mist suppression, but with somewhat different suppression efficiencies. After first contact, Licorice and the organic, for instance, showed a suppression efficiency of up to 69.7% but its efficiency gradually decreased as the number of contacts increased.

Feb 1, 2025

By Edmund H. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence - the total absence of noise except for ones own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working on the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur. But excessive noise is a health hazard. In recognition of this fact, our Congress included noise exposure as a part of the "Coal Mine Health and Safety Act of 1969". As Fig. 1 indicates, allowable noise exposure is established by specifying a time duration permitted at different noise levels. This is the well known "Walsh-Healey" criteria which governs noise exposure in many industries.

Jan 1, 1977

By V. F. Swanson

A petrographic study was made of the type and sources of mineral contamination occurring on phosphate rock products from Florida. Emphasis was placed on contaminants in the screened rock (+1 mm) since this portion of the product undergoes no physical beneficiation except for scrubbing to remove slimes. Since iron and aluminum con- tent of the finished product affect the salability, special emphasis was placed on identifying types and sources of these contaminants and relating chemical composition to visual characteristics. Wavellite derived from the overburden was the major aluminum contaminant with some aluminum being included as secondary clayballs. Iron occurred as phosphates in the overburden, and as colloidal oxides included in the phosphate pebbles. Chert and limestone contamination were derived from the Hawthorne formation underlying the phosphate matrix.

Jan 1, 1969

By Yuexin Han, Mu. Yufan, Yanjun Li, Peng Gao, Yongsheng Sun

"The objective of this study was to evaluate the effect of reduction temperature, reduction time and binary basicity on the size of metallic iron particles in coal-based reduction products of an oolitic iron ore. The particle size distribution behavior (i.e., cumulative passing percentage and mean size of metallic iron particles) during reduction was investigated in detail. Results showed that the particle size distribution of metallic iron particles was strongly influenced by reduction temperature, reduction time and binary basicity. The cumulative passing percentage and mean size significantly increased with reduction temperature and time in the entire range of the experiments. All curves of cumulative passing percentage versus particle size under different conditions demonstrated a similar trend (continuous increase). The size distribution parameters and mean size slightly increased with increasing binary basicity and significantly decreased when the binary basicity exceeded 1.0. The size of metallic iron particles could be controlled by adjusting the reduction conditions during coal-based reduction.IntroductionThe increasing demand for iron ore coupled with diminishing high-grade iron ore reserves has resulted in the urgent need for innovative technologies in order to use refractory iron ores. Oolitic iron ore is a typical refractory iron ore with tremendous abundance globally. Based on published literature, oolitic iron ore reserves are approximately 140 million tons in Europe, 10 billion tons in China and 66 million tons in Pakistan (Kazmi and Abbas, 2001; Wu et al., 2011; Yu and Qi, 2011; Sun et al., 2013a). Therefore, the efficient exploration and use of oolitic iron ore resources can play a significant role in easing the mineral resource crisis in the iron and steel industry. However, oolitic iron ore cannot be effectively upgraded by traditional beneficiation methods due to its mineralogical characteristics (e.g., low grade of iron, poor liberation of iron minerals and high phosphorus content) (Li et al., 2011b; Sun et al., 2013b).Researchers recently proposed coal-based reduction followed by magnetic separation to recover iron from refractory iron ores (especially oolitic iron ore) and a certain degree of breakthrough was achieved in both theory and practice. In this technology, iron minerals in the ore are directly reduced by coal to metallic iron, which grows into particles of different sizes. After comminution and liberation, metallic iron is concentrated by magnetic separation (Srivastava and Kawatra, 2009; Sun et al., 2013a; Li et al., 2011b; Sun et al., 2013b; Li et al., 2011c; Gao et al., 2013). Sun et al. and Gao et al. used this technology to examine the recovery of iron from oolitic and Bayan Obo iron ores, respectively (Sun et al., 2013a; Li et al., 2011b; Li et al., 2011c). Metallic iron powder with more than 90% iron content was obtained as the final product, which could be used directly in steel production."

Jan 1, 2015

With mine activity dating back to 1792, the Lehigh Valley, about 80 km (50 miles) northeast of the historic Allentown/Bethlehem steel mills and about 160 km (100 miles) northeast of Philadelphia, PA, defined early-day coal mining. Coal mining began just nine years after the end of America?s Revolutionary War. The high-carbon, clean-burning anthracite coal that was hand-dug from the Pennsylvania hills fueled the steam engines that powered the Industrial Revolution, helping build early steam ships and even the first automobiles. Around 1910, at the peak of the U.S.?s early mining effort, there were more than 250,000 men working underground ? 10,000 of them in the Lehigh Valley.

Jan 1, 2012

By C. C. Clark

The National Institute for Occupational Safety and Health (NIOSH), Ground Control Engineering Branch is investigating the use of shotcrete in weak rock mass mines with the objective of reducing fatalities and injuries resulting from rock fall accidents. When shotcrete is used as part of a multi-element ground support system there is a need to know when the material has developed a threshold early compressive strength of approximately 1 MPa (145 psi) for safe re-entry of miner and machine into shotcreted mine workings. This equates to the material having developed enough strength to be self-supporting and allow for emplacement of the remaining support elements that require drilling of the shotcrete layer without degradation. NIOSH researchers have developed methods and portable test equipment to measure shotcrete strength on-site in the first six hours after application using the ASTM C 116-90 (1990) standard. These advances were demonstrated in tests on five commercially available shotcrete mixes, sprayed as dry shotcrete using the field expedient methods and equipment. The strength values from these tests allowed for real-time identification of the early strength threshold and were consistent with strengths reported using laboratory-type equipment. The findings of this NIOSH research for determining shotcrete early strength can improve mine safety by providing a method for determining initial site specific material property values to be used for design and as a means to conduct on-site quality control and monitoring during production.

Jan 1, 2010

By R. W. Leonardson

Tectonic activity in northern New Mexico during late Oligocene and early Miocene time presaged events which led to the development of molybdenite deposits at Questa. East-northeast directed crustal extension produced north-northwest striking tensional fracture systems paralleling the early Rio Grande rift. A sequence of Oligocene andesite flows and breccias is overlain by a thick early Miocene rhyolite ash-flow tuff. Eruption of the tuff initiated collapse of the Questa cauldron: the south margin of which occurs as an east-northeast striking, north-dipping structurally weak zone. Continued east-northeast post-cauldron extension permitted the high level emplacement of granite stocks with coeval rotational deformation of fault blocks composed of cauldron fill and [ ] floor. The stocks occupy north-northwest fracture zones in the south margin of the cauldron, and porphyry dikes occupy east- northeast striking faults that define the south margin. These two fracture systems have played a dominant role in localizing the intrusive porphyries and associated mineral deposits at Questa. A molybdenite-bearing breccia matrix and related stockwork mineralization generally occur within volcanic rocks. Mineral deposits are spatially related to fault zones and the upper con- tact of their source intrusives. Deposits are localized in fault zones up to several thousand feet long and 100 to 500 feet in diameter. Magmatic-hydrothermal solutions from the source aplite porphyries have produced potash metasomatic alteration which is strongly centered on the mineral and ore zones. Alteration in ore is represented by orthoclase, quartz and secondary biotite. This pattern grades into secondary biotite and propylitic zones forming successively weaker alteration assemblages away from ore. Younger phyllic and argillic assemblages are particularly widespread only where strong north-northwest extensional fracture zones cross the south cauldron margin.

Jan 1, 2013

By A. H. Farazi, C. Quamruzzaman

The freezing and subsequent solidifying of unstable, weak (sands, silts and clays) and/or wet soil to form a desired-shape frozen barrier around a construction area are possibly the main features of the freezing method for shaft sinking. The barrier, along with strengthening the soil, provides a dry environment to ensure sustainable subsurface construction work before placing a permanent lining. The freezing method requires the installation of freezing pipes in boreholes around the construction area and the circulation of chilled salt water through these pipes and has long been a proven technique for dry shaft sinking through unstable and water-bearing seam around the world. As removing heat from the ground is the main feature of the method, an efficient thermal design of the freezing process is mandatory to ensure success of the shaft sinking operation. This applies to both the sustainability and economy of the intended structure. The design presented in this paper is aimed at figuring out the heat-removing ability and operating time of the refrigerative equipment using some simple formulae. The authors adopted a theoretical approach to determine the quantity of heat to be removed from the ground. The amount of energy for the equipment was found to be greater than that for freezing, which proved the validity of the design. The active freezing period was calculated to be 121 days. The authors followed the structural design of the freezing process they proposed in their previous work (Farazi and Quamruzzaman, 2013). Though the first coal seam in the coalfield was encountered at a depth of approximately 352 m in the subsurface, the target depth for cooling and freezing was decided to be 162 m. The formation demands extra care to nullify its risk of the temporary structure collapsing and water rushing in (Farazi et al., 2012). Discussion on the determination of refrigerative equipment parameters was excluded from the scope of this work.

Jan 1, 2014

By W. M. Luff

Introduction The Brunswick No. 12 mine is located about 27 km (17 miles) southwest of Bathurst, New Brunswick. The deposit is a stratiform massive sulfide deposit occurring in a series of sedimentary and volcanic rocks of the Tetagouche Group. These rocks are generally considered to be Ordovician in age. Ore reserves at Brunswick No. 12 are 104 Mt (115 million st) grading 3.72% lead (Pb), 9.01% zinc (Zn), 0.32% copper (Cu), and 97.9 g/t (2.8 oz per st) silver (Ag). Production in 1984 was 3.5 Mt (4 million st) at 3.57% Pb, 8.91% Zn, 0.32% Cu, and 100 g/t (2.9 oz per st) Ag. Total payable silver production that year was 211 t (6.8 million oz). This made Brunswick one of the largest silver producers in Canada. Bathurst-Newcastle area and Brunswick Mining Interest in the Bathurst area was aroused in 1897 when W. Hussey discovered an iron formation at Austin Brook, just south of Brunswick No. 6 deposit. This area, and the current No. 6 area, was explored from 1897 to 1907. Iron ore was mined at Austin Brook from 1907 to 1913 and from 1942 to 1943. Any occurrence of sulfides was overlooked until 1952. In 1952, M. J. Boylen Enterprises investigated the small sulfide body associated with the Austin Brook iron formation. Other electromagnetic anomalies associated with the iron formation were investigated. The No. 6 deposit was found late in 1952, when hole B12 intersected 97.5 m (320 ft) of massive sulfides. The No. 12 deposit, 10 km (6 miles) to the north, was found in 1953. More than 30 massive sulfide deposits have since been identified in the Bathrust area. In the 1950s, St. Joe Lead Co. did extensive test work on the No. 6 and No. 12 deposits, including shafts at No. 12, lateral development at No. 12, and testing at both deposits.

Jan 10, 1986

By Yang Zhao, Wanping Wang, Siqing Liu, Shuming Wen

"In China, most reserves of rich iron ores have now been depleted and sustainable development of low-grade iron ores has become a critical discussion topic in the mining industry today. The aim of this study was to evaluate the applicability of beneficiating a low-grade, hematite-magnetite ore (assaying 18.64% Fe) for subsequent utilization. In this study, process mineralogy and beneficiation of the ore were carried out in the laboratory. First, mineralogical investigation shows that the main metal minerals are hematite, magnetite and a little octahedrite that cannot be used at present, and the main gangue minerals include albite, quartz and ankerite. Based on the above, a combined process of magnetic separation and gravity concentration has been developed by using laboratory low- and high- intensity magnetic separators and a slimes shaking table, respectively. Factors affecting these separation methods are discussed, including process mineralogy on the tailings of the high-intensity separator, where the iron minerals were found to be finely disseminated in the gangue as inclusions. By applying a two-stage grinding step and a magnetic separation stage together with gravity concentration, a marketable iron concentrate assaying 60.79% Fe at a recovery of 60.23% can be obtained, when the feed assays 18.75%Fe, which provides some useful information for the sustainable use of low-grade iron ore.IntroductionIron is the world’s most commonly used metal. Steel, of which iron ore is the key ingredient, represents almost 95% of all metal used per year, primarily in structural engineering applications and for maritime purposes, automobiles and general industrial applications. By the end of 2009, the iron and steel production in China ranked the first in the world, and reached 0.567 and 0.537 billion tons, respectively. The domestic supply of iron ore was 0.88 billion tons and about 0.628 billion tons of iron ore were imported in 2009."

Jan 1, 2015

By Erik Westman, Brandon Stables, Benjamin Mirabile

"Standing support is often used in conjunction with underground retreat mining. Knowledge of the load-displacement behavior of standing support and loading induced by the mine opening is critical to proper support selection. The NIOSH STOP database contains load-displacement laboratory test data for most commonly used standing supports. Hydraulic load cells currently used to measure in-situ loading of standing supports have exhibited leakage under load, producing irregularities within the dataset. An improved hydraulic load cell eliminates leakage and produces more consistent data.INTRODUCTIONA hydraulic load cell, more commonly known as a flat jack or JackPack, is a device installed to determine the loading characteristics of the roof-to-floor supports. These standing or roof-to-floor supports include, but are not limited to pumpable cribs, cans, wooden cribs (4-point, 9-point, etc.), metal props, wood timbers, concrete donut cribs, and other variations of these standing supports.Flat jack devices have been used previously to determine the loading of such roof to floor supports. The most commonly used load cell for standing supports is based on a design intended for pre-stressing standing supports, not load measurement. Preloading helps to keep the supports, such as timbers props and cribs, in place during the dynamic loading associated with blasting (Barczak and Tadolini, 2004).Flat Jacks are manufactured in various shapes and sizes depending on the application; common shapes are square and round that are 25.4 mm (1.0 inch) thick when collapsed, as shown in Figure 1. These load cells are produced in South Africa and can be formed into several different shapes depending on the application (Barczak, 2003). The sheet metal that makes up the bladder is comprised of 19-gauge or 1.11 mm (0.04 inch) thickness; the top and bottom pieces of sheet metal are resistance-seam welded around the perimeter. There are two different ports installed on one of the bladder skin corners of the flat jacks; these ports allow fluid to fill the unit, and the other port has a relief valve. The fill port is comprised of a check valve. The pressure relief valve is located in the second port; preset to 1,724 kPa (250 psi), the pressure relief valve keeps the load cell from bursting. Bursting of these load cells typically causes a small tear in the metal skin allowing the fluid to leak out without a large catastrophic failure.The effective inflation range of these load cells is between 25.4 mm (1.0 inch) to 254.0 mm (10.0 inches) thick. Different types of fluids can inflate these load cells but the most common and easily accessible fluid for testing applications is water. Water pressure from the mine supply line can inflate these load cells to the desired load. Depending on the pre-stressing requirements, a pneumatic powered pump, hydraulic pump, or hand pump may be required to inflate the load cells."

Jan 1, 2019

By N. S. Aouad

"Gaseous explosions are one of the most hazardous incidents in process and mining industries. Experimental research in this area is shown to be high risk and expensive. Computational Fluid Dynamics (CFD) techniques are reasonable alternatives to experiments; specifically when testing large scale gaseous explosions such as methane explosion in underground mines. The dimensions of a confined space where explosions could occur vary significantly. Thus, the scaling effect on explosion parameters is worth to be investigated using CFD tools. In this research paper, the impact of scaling on the explosion overpressures is investigated by employing two scaling factors. These two factors are the Gas-fill Length scaling factor (FLSF) and the Hydraulic Diameter scaling factor (HDSF). The combinations of eight HDSFs (1, 2, 4, 8, 16, 32, 64, and 100) and five HDSFs (0.5, 1, 2, 4, and 8) will cover a wide range of space dimensions where flammable gas could accumulate. Experiments were conducted to evaluate the selected premixed combustion and turbulence models. Large Eddy Simulation (LES) turbulence model was used because it shows accuracy compared to the widely used Reynolds’ averaged models for the scenarios investigated in the experiments. Researchers also simulated methane explosions in both deflagration and detonation regimes using different numerical schemes. Three major conclusions can be drawn from the simulation results. (1) The overpressure increases with both FLSF and HDSF within the deflagration regime; (2) in an explosion duct with length to diameter ratio greater than 54, detonation is more likely to be triggered for stoichiometric methane/air mixture; (3) overpressure increases as an increment hydraulic diameter of a geometry within deflagration regime. INTRODUCTION The most typical category of gaseous explosion accidents is methane explosion accidents in the mining industry. It normally leads to significant economic loss and massive amount of casualties (McPherson, 1993). It could occur in unconfined spaces, such as combustion due to flammable gas leakage, as well as confined spaces, such as inner-combustion in process equipment and methane explosions in airways of underground mines. Gaseous explosions in confined spaces are more intensive compared to unconfined spaces provided that the total energy of explosives is the same. In addition, explosion characteristics are also affected by the geometry of a selected confined space. The size of confined spaces commonly encountered in process and mining industries could differ as much as an order of four (Catlin & Johnson, 1992). A better understanding of the scaling effect on gaseous explosions could contribute to explosion mitigation and prevent operation activities within high risk regions. This research paper has investigated this scaling effect and its impact on explosion propagation. The approach to investigate explosions is either experimental or numerical. Large scale explosion experiments are often costly and dangerous (Catlin, 1991; Zhang, Pang, & Zhang, 2011). Lab scale experiments and numerical methods are common alternatives. However, it is not yet clear if the findings in lab scale experiments can be used to represent the explosion characteristics or not. On the other hand, CFD modeling has been used to simulate chemical combustions and, thus, can be used to evaluate the scaling effects in methane explosions."

Jan 1, 2015

By Richard Emberley, Timothy Shaw, José L. Torero, Jurij Karlovsek, Timothy Gibson

"Tunnel closures are highly undesirable and the lengthiest are generally attributed to structural failures (e.g. Mont Blanc). Although historical data shows structural failures are closely linked to fire, design parameters for tunnel safety are not well defined. Current research has focused on defining the fire heat release rate and temperature, but these parameters cannot be easily used to determined structural performance. The energy transferred to the structure, the heat flux, is required but current literature lacks these values. Full scale experiments were undertaken on passenger vehicles resulting in heat fluxes between 20-70kW/m2. Analysis shows a vehicle fire’s duration is closely linked to its mass. Further analysis shows small vehicle fires can be scaled as a function of the tunnel diameter and the characteristic height of the desired vehicle. The present work provides engineers an appropriate design methodology to undertake informed thermal-structural analysis to minimize the risk of tunnel structural failure.INTRODUCTION Quantifying the effects of a tunnel fire depends on many factors such as the type of occupants, their vehicles and spacing, ventilation conditions and the geometric shape of the tunnel (Ingason and Lonnermark 2011). For design engineers investigating the thermal-structural performance of a tunnel, these factors are typically converted into spatial and temporal temperature distributions (Usmani et al. 2001) using various design curves such as those of ISO834-1, Hydrocarbon, Rijkswaterstaat (RWS) or RABT-ZTV (Promat 2013). However, to define a temperature profile through a structural element these curves require a heat transfer model that incorporates an appropriate boundary condition. The appropriate boundary condition is the net heat flux which is the result of a complex energy balance. For use in heat transfer calculations the net heat flux must account for the tunnel geometry as well as thermal properties of a given structural element and all other surfaces and mediums affecting the transfer of heat (Torero 2014)."

Jan 1, 2016

By A. W. Khair

In 1985, an extensive longwall mining research project was initiated by the West Virginia University Research Center entitled "An Improved Longwall Mining Technique" with the purpose of providing operational guidelines for the mining industry to enable efficient operation of its existing and projected longwall installations. One task involved in this extensive research project was monitoring ground movements due to longwall mining and evaluating their impact on surface and subsurface structures. This paper presents an analysis of the effects of topography on quasi-static and dynamic ground movements and the severity of damage inflicted on surface structures. The site was chosen for the study with an attempt to obtain a representative account of the topography experienced in the Northern Appalachian region, and more importantly to contain a substantial number of varying topographical features i.e., mountains, hillsides, valleys, and flat bottom land. The study was made possible by typical subsidence monitoring technqiues, however subsidence monuments were surveyed on a frequent basis, intermittently during face advancement. Ground movements were investigated under both quasi-static and dynamic conditions. This provided insight into the propagation of subsidence and the dynamic affects it has upon surface structures.

Jan 1, 1987

By Matt Bilson, Ritesh Mahajan, Antoni Kuras, Wataru Okada

The Waterview Tunnel comprises twin 2.4 km long 13.1 m internal diameter three lane road tunnels in Auckland, New Zealand. The City Rail Link (CRL) is a 3.45 km long, 6.24 m internal diameter twin rail tunnel underneath Auckland’s city center. This paper presents an overview of the tunnel geometry, segmental lining congurations, geometric constraints, performance criteria and functional reuirements for the large diameter Waterview Tunnels and smaller diameter CRL tunnels. Other key aspects, which include sustainability, innovations, construction performance and practical aspects are discussed and compared. Lessons learnt from these mega tunnelling projects are also presented.

Jun 23, 2024

By Jack S. Watson, Rasika Nimkar, Robert M. Counce, Matthew Gordy, Patrick Zhang

Waste phosphatic clay presents a difficult disposal problem and a significant loss of P2O5. Recent developments make this study on the use of phosphatic clay as a feed material for H3PO4 production worthwhile. (a) New data from Florida Industrial and Phosphate Research Institute (FIPR) suggest that the Bclay^ waste can be effectively treated by improved solid separation coupled with flotation to produce feed material for recovering additional phosphate. (b) The use of BOLI Flowsheet^ provides capability to predict performance of aqueous-based processes for a range of possible operating conditions. Using the new FIPR data and BOLI Flowsheet^ enabled the design of a new process that can potentially extend the usefulness of current P2O5 ore deposits. Predictions using OLI Flowsheet were able to identify process conditions that effectively overcome the difficulty of high Mg content of phosphatic clay. Estimated manufacturing cost in the current study lead to valuation of the P2O5 content of the phosphatic clay recovered/utilized at 60 to 70% of that of the phosphate rock feed material currently used. Phosphatic clay should be considered as a valuable material that is currently given zero value. The new FIPR data and BOLI Flowsheet^ enables the design of a new process that can potentially extend the usefulness of current phosphate ore deposits by extending the fraction P2O5 of recovered

By Dairo E. Chaverra, Carlos Argumedo‑Jimenez, Oscar J. Restrepo‑Baena

This paper presents the results obtained by processing a gold and silver telluride mineral concentrate from a mine in Colombia. An acid wash, also known as acidification, was carried out, followed by oxidation with nitric acid as a pretreatment. Cyanidations of the pretreatment residues were carried out and the results were compared with results from cyanidations of base materials. The removal of carbonates in the acidification, a tellurium extraction close to 90% during the pretreatment, and a 30% improvement in the gold recovery compared to the conventional process were achieved.

Nov 8, 2023