Search Documents

By David H. Carlson

The paper presents background information including data on diesel exhaust pollutants, amounts produced and standards, a desscription of mine characteristics that affect air monitoring techniques and a review of portable measurement techniques and instruments for gas and particulate matter sampling. A general review of the laboratory and field research being conducted at Michigan Technological University in the area of diesel emissions is presented. The facilities involved with this research are also described. These are the Experimental Mine, the diesel dilution tunnel test cell, the Mine Air Monitoring Lab (MAML), the portable instruments and the production mines used.

Jan 1, 1979

By T. J. Lutz, D. S. Yantek, L. Yan, J. R. Srednicki, J. A. Yonkey, G. T. Homce

Federal regulations require the installation of refuge alternatives in underground coal mines. Of the inuse refuge alternatives, more than 95 percent are mobile refuge alternatives, with the remainder being built-in-place (BIP) refuge alternatives. Heat/humidity buildup has been one of the major concerns with mobile refuge alternatives. For BIP refuge alternatives, however, there is a lack of in-mine heat/humidity test data to determine the extent of heat and humidity buildup. To quantify heat/humidity buildup in BIP refuge alternatives, the U.S. National Institute for Occupational Safety and Health (NIOSH) performed a series of heat/humidity tests on a 60-person BIP refuge alternative with and without a borehole air supply. At various times during the year, tests were performed with cooled, heated or unconditioned borehole air to examine how various outdoor temperatures may affect the thermal conditions inside a BIP refuge alternative. The results show that the air supplied to a BIP refuge alternative may require heating or cooling, depending on the outside air temperatures and the temperature of the mine. For example, during tests with an external ambient temperature above 21 °C (70 °F) and a relative humidity of 90 percent, providing 13 °C (55 °F) dew point air at 775 scfm, which is slightly higher than the mandated flow rate of 12.5 scfm per person, kept the internal apparent temperature below the mandated 35 °C (95 °F). Results for each test case are presented.

Jan 1, 2018

By M. A. Oskouei

Draglines are dominant machines and the most electricity consumers in surface coal mines. With the growing price of energy, environmental concerns, and the high sensitivity of mine profitability to dragline productivity, any improvement in efficiency of draglines can be beneficial for mines. Research has shown that operator skills have a significant impact on energy efficiency of loading machines. This study suggests a method to identify the key parameters that lead to differences in operator energy efficiency (responsible parameters). First, correlation analysis is used to identify parameters that are correlated to energy efficiency. Second, linear regression of a difference matrix is used to determine responsible parameters. Since this method is based on pair-wise comparison of operators, equal number of cycle is required for pairs of operators. Complete case analysis (CCA) is used to handle missing data problems. The final conclusion is made after removing the effect of random sampling and by considering all pairs of operators. Identifying responsible parameters can improve operator training programs. The suggested method is illustrated with a case study using field data.

Feb 23, 2014

By Sufi Md Gulzar, L B. Roy

Rock engineering tasks like tunnelling, dam and building construction, and rock slope stability rely heavily on properly estimating the rock’s uniaxial compressive strength (UCS), a crucial rock geomechanical characteristic. As high-quality specimen are not always possible, scientists often estimate UCS indirectly. The primary objective of this paper is to assess the efficacy of long short-term memory (LSTM), K-nearest neighbour (KNN), a combination of particle swarm optimisation (PSO) with an artificial neural network (ANN), and adaptive neuro-fuzzy inference system (ANFIS) to estimate the UCS of sandstones from Jharia, Dhanbad, India. Point load index (PLI), porosity (n), P-wave velocity (Vp), density (ρ), and moisture content (%) are the parameters used for the present study. Finally, a comparison was made between the various prediction algorithms outputs. The findings of the study validated the effectiveness of computational intelligence methods in forecasting UCS compared to other models used in this paper. The KNN achieves overall the best results, with an R2 of 0.95 for training, 0.94 for testing, and an RMSE of 0.03 for training and 0.05 for testing.

Nov 23, 2023

By Wei Luo

Nickeliferous laterites were characterized by particle size analysis, X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive X-ray analysis (EDX), Fourier transform infrared (FTIR) spectroscopy and thermal analysis. Results showed that the laterites consist mainly of nickel-substituted lizardite with cobble-like morphology and traces amounts of magnetite and phlogopite. As fluoride ions can react with silicon in the lizardite crystal structure and form metal-fluoride complexes, as well as increase the equilibrium constant of the lizardite dissolution in acid solution dramatically, the addition of minor fluoride salts (0.2wt.% NaF) gave a markedly enhanced metal extraction rate (Ni 81.7% and Co 52.3%) under the experi-mental conditions of particle size d50= 25 µm, 10% (v/v) H2SO4, reaction time 2 h, reaction temperature 90°C, liquid-to-solid ratio 3 mL g-1 and stirring at 500 rpm compared with H2SO4 alone (Ni 69.6% and Co 30.8%).

Jan 1, 2010

By Siqing Liu

A low-grade cassiterite-magnetite ore from Sichuan province, China, is finely disseminated, assaying 0.39% Sn and 23.20% Fe, respectively. Mineralogy studies show that the fine-sized cassiterite is mainly disseminated in iron minerals and gangue. Moreover, the embedded size of cassiterite is very fine and must be ground to -0.01 mm to achieve a degree of liberation of about 90%. Therefore, fine grinding needs to be conducted to get a high quality tin concentrate and a great loss of tin cannot be avoided when treating the ore by gravity concentration. Based on the above facts, a two-stage separation, with a low intensity magnetic separator and a shaking table, was selected to test the ore. Compared with other similar plants, a relatively good separation has been achieved. Three acceptable products for smelters were obtained as following: iron concentrate assaying 61.69% Fe with a recovery of 75.09%, tin concentrate assaying 27.21% Sn with a recovery of 56.97% and a sulfur concentrate assaying 40.86% S with a recovery of 32.03%, respectively.

Jan 1, 2011

By Z. D. Hora, W. N. Hamilton

Introduction Some unique opportunities exist for industrial minerals in British Columbia and Alberta. The region's diversified geology, particularly in British Columbia, offers favorable environments for a rich variety of mineral resources. Many minerals have been produced for years. For some, however, the level of production is far less than the potential. Others have had production in the past, but are not currently produced. Still others are known to exist and may have been actively prospected. But they are not yet developed. In addition, a number of speculative possibilities have recently come to light. The potential significance is not fully confirmed, but is suggested in showings in favorable geologic settings. Location and geography British Columbia and Alberta are the westernmost provinces in Canada (Fig. 1). The region overlaps two major physiographic divisions of the country, the Cordillera and the Interior Plains. It also takes in a small segment of the Canadian Shield on the east. The entire territory is greater than 1.6 Mkm2 (618,000 sq miles). Most of British Columbia lies within the Cordillera, a mountainous belt some 800 km (500 miles) wide. The belt is made up of three main physiographic components, the Eastern, Interior, and Western subdivisions. The Eastern subdivision embraces the rugged, linear ranges of the Rocky Mountains, elevations between 2600 and 3300 m (8530 and 10,800 ft). They form a 100-km (62-mile) wide band straddling the BC-Alberta border and extending northwest across northern British Columbia. The Interior subdivision includes several ancient mountain ranges but is dominated by an intermountane plateau area of low relief (average elevation 1200 m or 3900 ft). The Western subdivision is dominated by the Coast Mountains (elevations between 1800 and 4000 m or 5900 and 13,123 ft). These form a band about 175 km (110 miles) wide into which are sculptured the spectacular fiords of the BC coastline. Alberta lies largely within the Interior Plains, a prairie region of low to moderate relief (elevations between 200 and 1200 m or 650 and 3940 ft) formed of nearly horizontal bedrock strata. The Plains surface rises gradually to the southwest toward the deformed belt of the Rocky Mountains, where the bedrock strata are upturned, folded, and faulted. To the east, the Plains merge with the Canadian Shield, which exposes the Precambrian crystalline basement of western Canada. The total population of the BC-Alberta region is about five million people. Minerals, forestry, and agriculture are the primary industries here. It has well developed infrastructures to service these industries. British Columbia is third among the Canadian provinces in metal mining - $1.1 billion in 1985 - and first in forest products. It is also second in hydro-electric power development. Alberta leads all provinces in total mineral production, largely due to its extensively developed petroleum and natural gas resources - $26.2 billion in 1985.

Jan 12, 1987

By S. S. M. Chan

The design of most underground support systems has largely been based upon empirical rules. This design method has proven to be satisfactory in most cases as witnessed by the number of successfully completed works. However, the adequacy of this approach to the developing technology of ground support systems associated with deep excavation has not been substantiated. In cases where the material has definite time-dependent behavior parameters, rules of past experience become extremely vague and conservative. The Spokane Mining Research Center is currently engaged in extensive research to develop rational design methods for underground structures which will account for the many interacting factors such as in-situ properties of the rock mass, excavation methods, proposed types of support system, construction sequence, and environmental variables. The information presented in this paper pertains to only a segment of the research program,

Jan 1, 1971

By K. A. Perry, R. Q. Eades

The University of Kentucky conducted inerting tests and angle of ejection tests on three types of rock dust. A newly developed hydrophobic dust was compared against typical dry and wet dust applications. This new product is designed to alleviate respirable dust concerns for dry dusting and caking issues with wet dusting. Samples for both test types were prepared in a laboratory and subjected to temperature and humidity cycles that are typical of an underground coal mine. Inerting tests were conducted in a 38-L chamber with a 5-kJ Sobbe igniter. Angle of ejection testing was conducted at the University of Kentucky Explosives Research Team’s laboratory in Georgetown, KY. The results of these tests indicate that the newly developed dust has improved results for flame suppression and ejection compared with typical wet dust applications. The significance of these results is discussed with regard to existing respirable dust regulations and the issues associated with caking.

Jan 1, 2016

By Abhiram Kumar Verma, Soumya Ranjan Mallick

Generally, waste such as soil and sandstone is used in mines for road construction or haul roads. In many such mines, it is challenging to design haul road pavement to match the dumper capacity. This paper investigates overburden soil to find its utility as a pavement material. It is found that overburden soil is unsuitable pavement material without stabilization; hence, nine composite materials are developed using overburden soil and RBI. Physical, mechanical and microstructural properties of unstabilized and stabilized soil are determined. Statistical analysis is carried out to assess the effect of soil type, RBI and curing period of strength characteristics of unstabilized and stabilized soil. ANOVA tests assess the influence of RBI percentage on soil geotechnical properties, and regression relations are developed. Two-way ANOVA shows the effect of RBI and soil type on soil geotechnical properties, whereas one-way ANOVA shows that the influence of soil type is more than the RBI. The regression relation is developed for CBR, UCS, Poisson’s ratio and modulus of elasticity with a good correlation coefficient. The performance of RBI is more with the finer material and reduces with an increase in the size of soil grains. The performance of the developed composite is better than the earlier developed composite based on overburden with fly ash, lime kiln dust, lime or clinker.

Mar 19, 2024

By Eugie Kabwe

The velocity of detonation (VOD) is a significant property considered when rating an explosive. It may be quantified as a confined or unconfined velocity. The confined velocity is the rate at which the detonation wave propagates through an explosive within a blast hole or any restrained space. The unconfined velocity emanates when an explosive is detonated in the open. However, the confined velocity is more significant as explosives are usually employed under a definite degree of confinement. This paper evaluates the increment of air deck volume and its effect on the VOD. The air gap (air deck) volume is increased stepwise from 10 to 30% of the total blast hole volume by reducing the stemming height in the collar zone. Thereafter, the VOD estimation in the 172-mm-diameter explosive column is conducted using the Dáutriche technique. It is observed that the VOD reduced with the increasing air deck volume and detonation failure is high when 30% of the blast hole volume is replaced with air deck. It is deduced that the increment of the air deck volume has an effect on the attenuation of the steady-state VOD.

By Michael S. Moats, John Bailey Fletcher

Wear rates of grinding media can be misrepresented by marked ball wear tests (MBWT). Galvanic interactions between dissimilar grinding media can be affected by the chromium content in the media and the presence of oxygen in the environment. Corrosion, one component of wear, can be affected by many variables. Corrosion rates and corrosion potentials for modern high chromium white iron (HCWI) and high carbon steel (HCS) grinding media samples were obtained through electrochemical testing. In this study, the impact of chromium content in the grinding media and the dissolved oxygen in a simulated mill water solution on corrosion rates and potentials was examined. Increasing chromium content in HCWI above 15 weight percent increases the corrosion potential and decreases corrosion rate. Removing most of the oxygen from the solution lowers both the corrosion potential and corrosion rate of the materials tested. The electrochemical results were examined to model possible galvanic coupling effects on corrosion rates. Galvanic coupling between HCS and HCWI could cause differences in corrosion rates for almost all scenarios modeled. Based on the galvanic coupling analysis, MBWT results could be impacted by mixing HCWI and HCS in a ball mill charge. This impact is predicted to be more significant when dissolved oxygen is present in the mill water and as the chromium content of HCWI is above 15 weight percent.

Dec 21, 2022

By Shenghua Yin, Xun Chen, Rongfu Yan, Zepeng Yan, Wei Chen

The application of cemented paste backfill (CPB) with alkali-activated slag and phosphogypsum (ASP) can contribute to the sustainable development of the mining industry. The effects of PG content, NaOH content, solid content, and waste rock-rod milling sand (W/R) ratio on workability, unconfined compressive strength (UCS), and setting time of ASP-CPB were investigated in this paper. The results showed that the workability of ASP-CPB decreased with PG content and NaOH content. Compared to OPC-CPB, ASP-CPB exhibited better workability and higher long-term (7 days and 28 days) strength at predetermined backfill formulations and curing times. The mid-term strength of ASP-CPB first increased and then decreased with PG content, while the short-term strength (3 days) decreased gradually due to the influence of soluble acidic impurities. Excessive NaOH will harm the strength of ASP-CPB, possibly due to the swelling effect of the reaction products (ettringite and sulfate). Strength and setting time increased and decreased with solid contents, respectively. Moreover, the compactness of the mixture has an important effect on strength and workability. The workability and strength of ASP-CPB reached the minimum and maximum values at a W/R ratio of 5:5, respectively. Pollutant index detection indicated that most of the pollutants in ASP-CPB leachate met the discharge standard, which proved that ASP-CPB is an effective method to recover PG. The results of the research will provide theoretical guidance for the efficient recovery of PG resources and support the achievement of safe, clean, and efficient mining.

Nov 17, 2023

By Edward S. Plotkin, Gary A. Almeraris, Thomas F. Peyton

The lining of the tunnel and shafts for a new section of New York City's- water system required extensive components to produce, deliver and place a continuous tunnel linning. The project placed approximately 153,000 CM (200,000 cy) of concrete for 5,340 M (17,520) of drill and blast 7.3 M (24 ft.) ID tunnel, located at depths of 152 M (500 ft.) to 213 M (700 ft.) . This section of tunnel will be connected to the surface water distribution system via four shafts of varying diameters ranging from 5.8 M (19 ft.) ID to 1.5 M (5 ft.) ID . All work was done beneath the streets of Manhattan under the rigid constraints of the City of New York and the Bureau of Water Supply regulations.

Jan 1, 1987

By Rosa Malena Fernandes Lima, Kerollan da Silva Ramos, Joyce de Assis Silva, Geriane Macedo Rocha

This study evaluated the effects of collector type amide-amine compared with those of conventional etheramine acetate (both cationic collectors) on the surface properties of quartz and hematite. An examination of certain properties of the reagents indicated that the new collector amide-amine has CMC (critical micelle concentration) and pKa values (100 mg/L and 8.2, respectively) significantly lower than those of etheramine (800 mg/L and 9.4, respectively). Microflotation tests showed that the recoveries of quartz with amide-amine in all the concentrations tested were higher than those with etheramine. This is attributed to its lower CMC and pKa values. The selectivity window between quartz and hematite flotation using amideamine was higher at pH 10.5 (approximately 80% for 5 mg/L). Therefore, the use of starch is not necessary in siliceous itabirite flotation by amide–amine collector. Zeta potential measurements and infrared spectra reveal that the adsorption of amide-amine collector on quartz surface occurs mainly by electrostatic attraction. Considering the better collectability of amide-amine for quartz flotation and lower adsorption affinity for hematite surface than etheramine, the amide-amine is a promising collector to be used in reversal iron ore flotation.

Jul 30, 2021

By J. F. Barry

Newmont Mining Corporation and Barrick Goldstrike Mines, Inc. concluded an exchange of land and reserves in an agreement signed May 3, 1999.This exchange of assets allowed Newmont to develop the Deep Post underground mine from within Barrick’s Betze-Post open pit, thus reducing capital expenditures, lowering operating costs, and advancing the production schedule by nearly three years. Based on previous experience, Newmont is confident that the Deep Post underground mine can be successfully developed and operated within a large, active, open pit mine. The project also faces difficult geotechnical conditions including weak ground, scattered pockets of groundwater, and elevated rock temperatures.

Jan 1, 2000

By B. Samanta, S. Bandopadhyay

Ore grade modeling of a placer gold deposit is considered a challenging problem even today. Typically, gold-bearing deposits show extremely erratic and unpredictable grade variation. This is principally because of isolated occurrences of gold metal within a few high-grade pockets. Because of sporadic fluctuation of high-gold-grade distribution, the overall spatial continuity of the deposit becomes poor. This type of variation is often described by a lognormal or highly skewed frequency distribution, and the spatial continuity of the deposit is characteristically represented by a variogram model that exhibits a high nugget component. Further complicating the matter is the sparse availability of drillholes to capture such erratic variation. Due to the prohibitive cost of drilling, gold grade and reserve estimations are typically carried out using insufficient exploratory data. Use of a traditional estimation technique on limited data often produces an unreliable ore grade model. Kriging and its nonlinear variation, lognormal kriging, are frequently used in gold deposit modeling (Rendu, 1979; Journel, 1980); however, kriging is flawed by the smoothing effect. Moreover, though kriging is known to be globally unbiased, it is not free from conditional bias. As a result, if a deposit is modeled using the traditional kriging technique, a high-grade zone can be predicted to be a low-grade zone and vice versa. Predicting high grade as low grade results in a missed opportunity to exploit profitable ore. On the other hand, prediction of low-grade ore as high-grade ore might result in financial loss for a mining operation. Thus, the use of kriging for ore grade mapping of a gold deposit may not be recommended. Estimation techniques (including kriging) can produce an estimate with minimum error in a minimum-error variance sense. However, no matter which estimation technique is used for grade modeling of a highly erratic deposit like gold, the error margin is bound to be high. Therefore, any grade prediction made for an unknown location is associated with high uncertainty. Since various mine-planning operations, including derivation of grade tonnage curve, pit design and economic analysis of the deposit, are based on estimated grade rather than true grade, a mining project evaluation that depends upon estimation will be subject to considerable risk. Thus, the successful design of a mining project not only depends upon accurate grade estimates, but also upon accurate assessment of uncertainty, for predictive grade is equally important. Although the kriging standard deviation is used as an indicator of uncertainty for prediction, it is flawed by characteristics related to a data-independence property. This study, therefore, investigates the stochastic simulation technique of conditional simulation for ore grade modeling of a placer gold deposit at Nome, Alaska. It is expected that the research will provide a better solution to ore-grade deposit modeling than the kriging technique because (1) conditional simulation preserves spatial continuity as well as reproduces the data histogram, thus avoiding the smoothing problem; and (2) generation of multiple realizations helps to accurately quantify the uncertainty about grade values in the deposit.

Jan 1, 2009

By Saghar Farajzadeh, Fatemeh Kazemi, Ataallah Bahrami

Spirals, the most common equipment for the separation of heavy minerals such as chromite, are greatly affected by size distribution and the liberation degree (hence the specific gravity and size) of the feed particles. In this study, the efficiency of spirals in separation of low-grade chromite particles has been investigated by studying the distribution of grade, size distribution and liberation degree of feed, concentrate, and tailings of spiral. For this purpose, mass balance constraints were applied to the spiral-containing chromite processing circuit. Afterwards, the grade variations and size distributions have been investigated. According to the results, when the feed to the spiral has a larger size distribution, the enrichment ratio of the feed is 1.32 and, with the smaller feed size, this value has increased to 1.99. When the spiral feed has a larger size distribution and higher specific gravity, the recovery of chromite increases with increasing particle size up to 250 microns, and then with increasing particle size, recovery decreases with a relatively steep slope. Evaluation of spiral efficiency with respect to particle liberation degree has also shown that despite the high degree of liberation of spiral feed in size fractions smaller than 75 microns (88.9%), the liberation degree of spiral concentrate and tail in this faction is equal to and less than that of feed, which can indicate poor spiral performance in these size fractions.

Oct 27, 2020

By Muhammad Kamran, NIAZ MUHAMMAD SHAHANI

This study elucidates a new idea to predict mine fire levels by employing several machine learning techniques. A total of 120 patterns of various mine fire influencing parameters, such as oxygen, nitrogen, carbon monoxide, and temperature, were compiled from the Adularya coal mine in Turkey. Techniques like t-distributed stochastic neighbor embedding (t-SNE) and k-means clustering were used to process the data, and support vector classification (SVC) was executed to predict various levels of the mine fire. The results revealed that the proposed model has higher credibility to predict the various levels of underground mine fires.

Feb 14, 2022

By D. McElhinney, K. Mohamed, T. Batchler, T. Matthews

Steel props are a type of standing support utilized in coal mines to support mine roof. In addition to the vertical roof loading, sometimes the steel props are subjected to lateral loading of spalled ribs. To enhance the safety of mine workers, the performance characteristics of the steel prop was studied under different scenarios of vertical and lateral loadings. Quik Stik props were used for use in this study. A uniaxial compression loading test was conducted for the Quik Stik prop assembly (inner and outer tubes, ball bearings, collar) to investigate the loading mechanism of the prop. Rupture tests were conducted for the inner and outer steel tubes of the Quik Stik props to estimate the yielding strength of the steel tubes. Nine Quik Stik props of 8-ft high were tested using the Mine Roof Simulator (MRS) at the National Institute for Occupational Safety and Health (NIOSH) Pittsburgh research facility. Three props were tested under vertical loading to measure the vertical loading capacity of the props. Six props were tested under lateral loadings with low and high roof-to-floor convergences to measure the lateral loading capacity and the retained vertical loading capacity of the props during lateral loading. Vertical loading tests showed that the tested props could be classified as yieldable supports with a stable load capacity of about 110 kips to 140 kips. Lateral loading tests showed that the vertical load capacities of the tested props were diminished because of applying lateral loads, and the props behaved as nonyielding supports with a maximum lateral load capacity of about 8.5 kips to 9.5 kips at stable lateral displacement up to 3 inches.

Feb 1, 2023