Search Documents

By S. D. Thompson

An AIME transaction by P.L. Allsman (1960), "Analysis of Explosive Action in Breaking Rock," contains many useful concepts applicable to blast design. Of special interest was the derivation of a heave blasting burden formula, which is important in establishing the maximum burden. Unfortunately, its derivation contains a fundamental error and then a compensating one. This formula was: [ ] The derivation used the impulse-momentum principle, with a 0.3 m thick (1 ft thick) radius of rock mass being acted on by an explosive impulse. However, the rock weight was not converted to mass by dividing by the gravitational constant. This mistake can be verified by checking the units in the formula, which resolve into m%-sec instead of meters. Adding the gravitational constant corrects this: [ ] If the minimum velocity is now taken as 0.3 m/sec (1 ft per sec), as was recommended, excessively large burdens result. Any appropriate rock velocity should be capable of throwing the rock mass a minimum distance so that the swell needed for breakage can occur. Unless the burden is extremely small and the bench height is very high, it is unlikely that a velocity of only 0.3 m/sec (1 ft per sec) will be sufficient. A review of the literature indicates that average rock velocities observed by camera studies typically range from 15 to 30 m/sec (50 to 100 ft per sec) (duPont deNemours and Co., 1977; Tansey, 1979). On this basis, a minimum rock velocity of about 15 m/sec (49 ft per sec) would be expected and not 0.3 m/sec (1 ft per sec). When a velocity of 15 m/sec (49 ft per sec) is inserted into the corrected formula, the results approximate those of the original formula with a velocity of 0.3 m/sec (1 ft per sec). The errors were approximately self-compensating [ ] References Allsman, P.L., 1960, "Analysis of Explosive Action in Breaking Rock," Transactions, AIME, Vol. 217, pp. 475-476. E. I. duPont deNemours and Co., 1977, Blasters' Handbook, 175th Anniversary Edition, Dupont, Wilmington, DE, pp. 233. Tansey, D.O., 1979, "The DuPont Sequential Blasting System," CIM Bulletin, Vol. 72, July, p. 80. Thompson, S.D., 1981, "Critical Review and Revision of Surface Blasting Practice," MS thesis, West Virginia University, pp. 308-316.

Jan 3, 1985

By J. M. Manka

American mining companies operate many drum hoists that hoist from various depths with varying payloads. This paper will review the procedure of selecting optimum wire rope constructions for these existing hoisting installations. Selection for proposed installations along with recommended hoisting parameters will also be presented. To achieve this optimum rope performance, preventative and corrective maintenance procedures will be reviewed along with examples of rope problems and their causes.

Jan 1, 1992

By Kenneth F. Wyman

The following report details the successful construction of Contract 2A of the Three Rivers Water Quality Management Program, Intrenchment Creek Combined Sewer Overflow Conveyance System, in DeKalb County for the City of Atlanta, Georgia. The contract required construction of approximately 2878 m (9443 ft) of tunnel bored to an initial diameter of 7.95 m (26 ft 1 in), with provisions to concrete line those portions designated by the engineer to a finished internal diameter of 6.91 m (22 ft 8 in). Flanking the tunnel are two shafts. The upstream shaft was excavated to a nominal diameter of 4.87 m (16 ft) to accommodate a finished internal diameter of 3.66 m (12 ft). This shaft required a transition boot fully concrete lined to final dimensions of 6.91 m (22 ft 8 in) wide, 13.72 m (45 ft) long, and varying in height from 6.91 m (22 ft 8 in) to 12.80 m (42 ft). Associated work necessary to complete the contractual obligations included installation of 22.86 m (75 ft) of cut-and-cover box culvert, 484 m (1589 ft) of open-cut sewer installation in sizes ranging from 0.30 m (12 in) to 1.68 m (5 ft 6 in), one river crossing, 137.46 m (451 ft) of monolithic concrete trapezoidal channel, and installation of 19125 cu m (25000 cu yd) of select fill material compacted and graded to finished contours. The downstream shaft was excavated to a minimum diameter of 12.04 m (39 ft 6 in) and concrete lined to a finished internal diameter of 10.67 m (35 ft). Requirements here included installation of a complete pumping station with all mechanical, electrical, and structural elements necessary for dewatering the tunnel through the controlled use of four 250 hp submersible pumps discharging into the facilities of the Intrenchment Creek Water Pollution Plant. The objective of this project was to collect combined storm runoff and sanitary flows currently coursing through Intrenchment Creek

Jan 1, 1985

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By Donald W. Gentry

This section deals with one of the most fascinating aspects of mining the evaluation of mine investment opportunities. Be-fore proceeding further, it is important to clarify the meaning of some fundamental terms used frequently in the text. 6.0.1.1 Mine Valuation vs. Evaluation The words "valuation" and "evaluation" in a mining context are often used interchangeably. However, for the purposes of this section, a distinction is made between the two terms in accordance with commonly accepted practice. The word valuation in a mining project context has the rather narrow meaning of placing a dollar or other currency value on the worth of the project as a whole. In other words, the value of a mining project refers to a measure of the desirability of ownership of that property. As such, the major item of interest is, "what is the mine worth?," or `what is the value of the mine?" The value of a mining project may actually be determined in the marketplace at any specific point in time, or it may be estimated by one of several methods. The topic of mine valuation is discussed in more detail in Chapter 6.1. The word evaluation in a mining project context connotes the broader meaning of determining the numerical values of all

Jan 1, 2008

By Knut H. Hubert

The GRATE-KILN System plant at Svappavaara, Sweden, was constructed for LKAB by Allis-Chalmers under a turnkey contract and commissioned in 1969. The plant was designed to produce iron ore pellets from magnetite concentrate at 6100 mtpd using imported fuel oil. It represented the state of the art for plants of its type at the time. Fuel rated capacity was attained within one week of start-up. Product quality, power usage, fuel consumption and machine wear were within warranty limits during sustained production thereafter. As operator skills improved and gas handling system reserve capability was utilized, the plant frequently produced acceptable product at up to 115% of design capacity. During the period 1969 to 1976, market demands increased for high-quality pellets while energy costs rose steadily. At the same time, important advances in the design of GRATE-KILN Systems were being made in other plants constructed by Allis-Chalmers.

Jan 1, 1980

By George M. Potter

Under contractural arrangements with the Bureau of Mines, Mountain States Research and Development, Inc. (MSRD) completed a technological investigation to determine the feasibility of in situ mining of metal commodities other than copper and uranium, The study was based upon available literature and experience. The selection of potential candidates for in situ mining was influenced by economic importance, probable amenability to in situ methods, and environmental considerations. Four metals (or metal pairs) were chosen for feasibility studies: aluminum (with a copper byproduct), gold-silver, and manganese were recommended for further study and action; cobalt-nickel was also recommended contingent upon preliminary laboratory leaching and recovery investigations and field geohydrological work. Mining and recovery plans and an economic evaluation are included. Other metals with potential for in situ leaching are lead/ zinc, molybdenum, and vanadium.

Jan 1, 1981

By Aldin Ardian, Mustafa Kumral, Jagjit Singh

Risk assessment of mining projects is a requirement in the mineral industries. In this process, many risk variables are timedependent, and the only available data are historical time series. Moreover, in the case of a multivariate scenario, conventional forecasting methods fail to capture conditional dependency across the variables, which is important when there is an underlying causal relationship that needs to be modeled for accurate project evaluation. Thus, we investigated the use of copulas to capture the conditional distribution of the factors involved in a mine risk assessment study. We employed a multivariate copula-based time-series approach to model several uncertain variables. The Autoregressive Fractionally Integrated Moving Average - Generalized Autoregressive Conditional Heteroscedasticity (ARFIMA-GARCH) model was used for the conditional mean and copulas were used to model the error distribution, thus capturing the collective variation and dependence pattern across the variables. The method was implemented to model gold prices, copper prices, and the 10-year US Treasury bond yields and to determine the project’s net present value and probability of being economically feasible. The proposed approach can be used for cases where simulation of multivariate time-series is conducted.

Apr 13, 2021

By J. D. Miller, R. J. Smith

Earl C. Herkenhoff Publication of the article "The Flotation Behavior of Digested Asphalt Ridge Tar Sands" by R.J. Smith and J.D. Miller has confirmed and again spotlighted a most significant and important development in the field of tar sand and heavy oil mining. This is the ability to recover 95 % of the bitumen in dry tar sands by a hot water process. The initial investigation by Miller and Sepulveda in early 1978, "Separation of Bitumen from Dry Tar Sands," was the first blockbuter. It is disappointing that there has been so little scientific and industry ackowledgement that the authors laid to rest the long entrenched belief that the sand grains had to be "water wetted" for a hot water process to be applicable. Dr. Miller and his researchers at the University of Utah used slightly different mineral dressing terminology in describing their process but it is essentially the old, established technique of high solids attrition scrubbing at elevated temperatures with a conditioner or modifier, followed by dilution and froth flotation. Similar techniques were described in detail for other nonmetallic minerals in the mid-1940s by Stuart Falconer of American Cyanamid Co. The authors used a 15-minute "scrub" period (or in their terminology "digester step") at 73% solids and 95°C (203°F) in a 0.3 m solution of sodium carbonate -about 4 kg/t (8 lb per st) of tar sand. Flotation was at 10% solids. Obviously, the scrub is an expensive step with respect to energy input but the high recovery of bitumen appears to justify it. Two basic questions then arise: • What are the effects of shorter scrubbing time, lower temperature, and less sodium carbonate? • Would a two-stage approach be advantageous? That is, could you get the major proportion of the bitumen with a mild scrub and apply the high power and temperature only to the refractory portion? These variables should be evaluated. Apparently, all results were only for rougher flotation. What would the grade and recovery of bitumen be if multiple cleaner flotation steps were employed? We must concede that a 60-62% grade of bitumen leaves considerable room for upgrading. Finally, it should be noted by all executives who approve funds for heavy oil recovery schemes, most of which are variations of in-situ methods, that mining can yield a 95% recovery of bitumen. That is correct, 95%. Imagine what that does to the total barrels recovered from a heavy oil resource compared with the scrawny 30-35% maximum recovery we are getting now. The conclusion-let's mine heavy oil and tar sands. Reply by R.J. Smith and J.D. Miller We, too, share Mr. Herkenhoff s enthusiasm for the mining of tar sands-heavy oil and continue the development of related processing technology. Specifically, it will be noted that by appropriate control of bitumen viscosity in the feed (probably the most important variable for successful separation) the recovery can be accomplished at low digestion temperature and low addition of alkali. A 91 t/d (100 stpd) pilot plant based on our technology is now being operated by Enercor in Salt Lake City (Hatfield, Oblad, and Miller, 1982). In these same pilot facilities, rougher concentrates containing more than 80% bitumen on a dry basis are being produced from Asphalt Ridge Feed. However, the processing of certain other tar sands results in incomplete digestion of bitumen/sand aggregates as discussed elsewhere (Miller and Misra, 1982). Such undigested aggregates are shown in Fig. 1. In this regard, it is intended that a recycle stream will be installed in the pilot plant to provide for redigestion of middling products. Further details regarding surface chemistry aspects of this tar sand technology have recently been published (Misra, Aguilar, and Miller, 1981). References Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Recovery of Bitumen from Oil Wet Tar Sands," Processing, Second International Conference on Heavy Crude and Tar Sands, Caracas, Venezuela, Feb. 7-17. Hatfield, K.E., Oblad, A.G., and Miller, J.D., 1982, "Pilot Plant Processing of Oil-Wet Tar Sands," Symposium, Rocky Mountain Fuel Society, Salt Lake City, Utah, Feb. 18-19. Miller, J.D. and Misra, M. 1982, "Hot Water Process Development for Utah Tar Sands," Fuel Processing Technology, Vol. 6, No. 1, April, pp. 27-49. Misra, M., Aguilar, R., and Miller, J.D., 1981, "Surface Chemistry Features in the Hot Water Processing of Utah Tar Sand, Proceedings, "Symposium of Separation Science and Technology for Energy Applications," Gatlinburg, Tennessee, May 5-8.

Jan 11, 1982

By G. Pan

Although geostatistical techniques have been widely accepted as the standard methods for reserve calculations in the mining industry, the production data of many mines frequently differ from geostatistical estimations based on exploration and development drilling. The discrepancies in recovered metal amounts, commonly in the range between 10% and 30%, are related to different factors. Major causes vary from mine to mine. A common cause, however, is the ignorance of important geological constraints in reserve modeling. Three major factors appear to be related to such an unfortunate fact: 1) modelers are over-confident on geostatistical techniques, 2) it is difficult to establish geological models, and 3) mine schedules are too tight to allow detailed geological modeling work. Defining mineralization envelopes has been a major effort in geological modeling. Past experiences have showed that geological modeling is much mo~ demanding than the choice of sophisticated kriging estimators. Since building envelopes for complex ore bodies can be extremely tedious and time-consuming, computerized approaches are badly needed for mine modelers. A comprehensive procedure reported here is referred to as probability-assigned constrained kriging (PACK), which includes a built-in method for defining 3-d mineralization envelopes. The modeling technique is fast and accurate for complex precious metal deposits. The technique is demonstrated on a gold deposit. The estimation results are compared with blast-hole based production panels, showing that the estimated tonnage is 2.2% larger than the actual production and the average grade is 2.6% lower.

Jan 1, 1994

By Sheldon P. Wimpfen

Back in 1970 Congress passed the National Mining and Minerals policy Act, which had as one of its basic tenets to rely on a strong and stable private minerals industry for the development and production of our mineral resources. Since then, a substantial amount of legislation has been introduced that impacts on the minerals industry. Although most of the bills proposed are not passed into law, each bill affecting minerals and mining is given careful review by the Bureau of Mines. Comment is forwarded with the object of being helpful to legislators by providing our assessment of the probable impact of each bill proposed along with suggestions to improve them. Actually few bills introduced become law. For example, in the 93rd Congress 4,260 bills were introduced in the Senate and 17,690 in the House. In the final accounting there were passed 123 private laws and 649 public, 3 percent of the bills introduced. There would be little merit here in attempting to analyze each mineral-related bill that was proposed. Many are similar and aim at making a certain aspect of our minerals activity fit needs. So, to simplify the task the many bills have been grouped by subjects. Slide 1 shows the principal topics and the number of related bills introduced. Putting it altogether, there are 26 principal subjects and almost 200 bills. And these numbers are probably off somewhat, as this accounting was made early in December.

Jan 1, 1976

By K Martin, C. J. Nelsen, J. L. Schutz, S. R. Maynard

Investigations in the Ortiz Mountains have revealed the relationship of igneous activity and gold mineralization to the Tijeras-Canoncito Fault System (TCFS). The northeast-trending TCFS passes through the southeastern part of the Ortiz Mountains where its principal structure is the asymmetric Ortiz Graben. Several fault blocks, containing up to 305 m (1000 ft ) of Eocene Galisteo Formation, comprise the graben that has up to 1220 and 610 m (4000 and 2000 ft) of stratigraphic separation on its southeast and northwest sides, respectively. Intrusions in the Ortiz Mountains can be subdivided into two petrochemical types: an older calcalkaline suite and a younger alkaline suite. The calc-alkaline rocks are characterized by extensive sill, dike, and laccolithic bodies of latite-andesite intrusives and at least one younger (?) granodiorite stock at Candelaria Mountain. The alkaline rocks consist of a large nepheline-bearing augite-monzonite stock, a latite-porphyry hypabyssal plug, the Ortiz diatreme (vent breccia), and trachytic-latite dikes radial to the diatreme. K-Ar age determinations suggest the older suite to be 34 +/-2.2 million years while the younger alkaline rocks range from about 30 to 26 million years. Gold mineralization in the Ortiz Mountains occurs in five distinct environments: brecciapipes, skarns, veins, porphyry-like stockworks, and placers. Lode mineralization is associated with the alkaline suite of intrusive rocks postdating the Ortiz diatreme and predating most of the trachytic-latite radial dikes.

Jan 1, 1991

By Charles H. Dowding

INTRODUCTION "On many projects, the tendency is to drop interest and support of the geological service as soon as it seems safe. That . . . is a short-sighted policy . . . It would be of further service perhaps to learn whether predictions were reasonably true to life." --C.P. Berkey, 1938 (3) This paper quantitatively compares predicted and encountered shear zone size and location and rock type for tunnels in the Colorado Mineral Belt. The Colarado Mineral Belt is composed of igneous formations with associated metamorphic rocks and faulting. As such, it represents the most complex of provinces for at-grade predictions (27). Shear zone and rock type data are assumed to be statistically homogeneous because of the common geology of the seven tunnels. It is often felt by geologists and engineers that the amount of information from which a geological model is created is so low that any statistical inferences are unstable. In other words, the addition of new data may drastically alter the means and variances suggested by the model. Therefore, predictions are rarely couched in quantitative statistical terms but modified with "probably," "most likely" or "possibly." Comparison of predicted and encountered data from past geological models will permit the "probably's" to be quantified and distilled from the art of geological prediction. To date, two other studies of the validity of predictions have been made (26 and 16). Together, these two studies indicate that

Jan 1, 1976

By M. S. Fraley

As we compete for close margins in wholesale sales, the effects of both quality and price have a major impact on the cost of producing electricity.SO2 emission allowances have traded as low as$60/ton to as high as $215/ton over the last three years. This price spread in emission allowances clearly demonstrates the correlation between the quality of fuels versus the price utilities will be willing to pay for them. This paper provides an overview of the effects of the qualities of fuel, coupled with transportation as well as environmental concerns on the price of fuel and the ability to compete in a deregulated electric market.

Jan 1, 2000

By D. H. Horswill

Red Dog, the world’s largest zinc mine, is located ninety miles north of the Arctic Circle in northwest Alaska on lands owned by the Inupiat Eskimo organization called NANA. NANA received a subsurface title over this resource as part of their settlement lands under the Alaska Native Claims Settlement Act and subsequently entered into a Lease Agreement with Cominco in 1982. Cominco, an international mining company focused on zinc, built and operated the mine. NANA’s principle objective in the development of the mine was to have it contribute to the development of sustainable communities within their traditional region. This meant creating job opportunities in a modern economy while preserving the traditional subsistence lifestyles. Preservation of their culture, language, and traditions are as important to the NANA people today as they were through ages past. The principles of sustainable development – matching economic, environmental, and social goals through continuous communications and high commitment to efficient and effective operations – have been core values for the Red Dog Mine from the beginning. This paper will describe how a large mining operation in a remote corner of the world has been able to contribute toward sustainable development in that region.

Jan 1, 2000

By A. Anttila, S. Persson

The grinding mill is probably the most common unit operation in mineral processing. There is, however, much that can still be done in the way of optimization. This paper discusses the results of a well-controlled pilot-scale test in which the performance of a tumbling mill equipped with a conventional rubber lining and lifter bars was compared to a tumbling mill equipped with a smooth rubber lining of the magnetic type. The results indicate that the smooth lining is about 14% more effective with respect to energy consumption. By optimizing the size of the grinding media, the mill capacity can be increased in many grinding operations. In this specific case, grinding with a -20-mm ball charge required 26% less grinding energy than grinding with a -30-mm ball charge. The energy savings can, in most cases, be converted to an increase in capacity. The wear of the grinding media is difficult to assess over a short test period, but the results suggest that the wear is somewhat less when a smooth lining is used. A determination of the wear of the linings was not included in this study, but it is generally accepted that the use of magnetic linings reduces the lining costs dramatically. Computer simulation using the Millsoft code developed by Mishra et al. confirms and explains the increased effectiveness of comminution when a smooth lining and smaller grinding balls are used.

Jan 1, 2000

By D. A. Norrgran

The term "secondary recovery" has recently brought on a new meaning in view of the depletion of natural resources, energy conservation, plant optimization, and the environmental consciousness that has led to hazardous waste management, recycling, and secondary processing. Many secondary recovery processes are being developed applying mineral processing technology. Gravity separation, magnetic separation, and flotation have all emerged as implicit methods for recovering residual values from various process streams and hazardous constituents from waste streams. Recently, a technique for concentrating metallics has been successfully reintroduced. Although the concept of the eddy-current separator was developed over a century ago, (Patent 400317 issued to Thomas Edison on March 26, 1889) it was not until this last decade that it gained prominent acceptance. The evolution of permanent magnets has provided a cost effective alternative for the generation of high intensity magnetic fields. High energy permanent magnets have substantially reduced the capital and operating costs over the electromagnetic circuits employed in antecedent eddy-current separators. Specifically, in recent years, the strength of permanent magnets has increased several fold with neodymiun-boron-iron rare earth magnets now providing an energy product of 35 million gauss-oersted. Figure 1 shows the evolution in the strength of permanent magnets. The development of these rare earth magnets has led to the design of circuits possessing a magnetic force an order of magnitude greater than that of conventional permanent magnetic circuits.

Jan 1, 1991

By V

"Recent regulations, as well as a general aversion to central dust collectors within the Powder River Basin Coal user’s community, have created a need for an alternate method for eliminating airborne dust. This paper addresses the capital expenditure as well as the cost of ownership of an integrated point source air cleaning system in comparison to a central collection system. This assessment was conducted by comparing the cost to purchase and operate a central dust collection system and integrated air cleaner system on a typical multiple transfer point application. The central dust collector consists of a negative pressure blower, a series of filter bags, a collection hopper, a screw conveyor to place collected material back into the material stream, and a series of ducts to pull air and dust from individual pickup points. The point specific integrated air cleaners consists of a negative pressure blower to pull dust and air from an application point through a bag-less filter media located at the application point. The agglomerated material is then redeposited into the material stream at point of use without the need for ducting or a central material hopper. The assessment yielded a 54% reduction in capital expenditure and a 26% reduction in operating costs for the same application when using individual dust filters as opposed to a central system. In addition to the lowered cost, there are reductions in risk associated with the elimination of ductwork and the central containment enclosure for collected explosive dust. By the conclusion of this paper, the reader will have a better understanding of the quantifiable differences between a central dust collection system and a set integrated air cleaner systems. BACKGROUND Spillage has always been a problem in the bulk solids handling industry. As long as there have been conveyors, there has been spillage. Spillage is material that falls off a conveyor belt and creates a hazard in the environment around a conveyor belt."

Jan 1, 2016

By T. J. Close

The Silver Peak Range North Wilderness Study Area was deleted from the list of US Bureau of Land Management lands in Nevada to be considered for wilderness designation. This decision was based in part on the US Bureau of Mines mineral investigation of the wilderness study area which found indications of precious- and base-metal-resources. The study area lies between the Silver Peak and Dyer mining districts of west-central Nevada. The Bureau examined 13 mineralized sites, most of which were previously unknown and unclaimed. These sites are along two zones that cross the study area from the Silver Peak mining district to the Dyer mining district. The two zones transect a volcanic center of fractured and altered rocks that contain epithermal veins of quartz and calcite with gold, silver, and base-metals. At the surface, these veins are poorly defined. Exposures of the more than forty veins examined were as thick as 17 ft and as long as 1000 ft. Samples from these veins contained significant amounts of precious- and base-metals-as much as 0.02 oz per ton gold, 2.1 oz per ton silver, 1.0% copper, 2.6% lead and 0.4 % zinc. No vein large enough or of high enough grade to be classified a mineral resource was disclosed by the sample data. However, most do have indications of precious- and base-metal-resources at depth. Subsurface exploration of some of the veins is recommended.

Jan 1, 1995

By David Mast, Irwan Halim, Seung Han Kim

Nowadays more infrastructure tunnel projects are procured using design-build method. In this environment, the Owner’s engineer would typically provide performance requirements for the design-builder, and the Contractor’s designer would work with the contractor to design the tunnel lining based on the Contractor’s means and methods and manufacturing process. This paper will describe the typical requirements provided by the Owner based on its design objectives, and the means and methods by the Contractor that would significantly impact the design. Project examples and recommendations for Owner’s requirements will be provided that can optimize the design and still achieve the Owner’s performance objectives.

Jun 13, 2021