Search Documents

By Syd S. Peng

Introduction The most commonly used ground control design in coal mining is the determination of pillar size by various pillar strength formulae for mine layout (Bieniawski, 1983; Holland, 1973; Hustrulid, 1976; Obert and Duvall 1967; Wilson and Ashwin, 1972). However, there have been few documented case histories concerning the validity of those strength formulae. Recently there are indications that those strength formulae tend to overdesign considerably. From a safety point of view, there is nothing wrong with overdesign. But an overdesign with large chain pillars reduces the flexibility of machine movement and decreases production. It also reduces coal recovery and, thus, shortens the reserve's life. This is especially true for small operators who own a limited reserve. Those small mines, through past practices or out of necessity, experiment with smaller pillars than those predicted by the strength formulae. Conclusive ev¬idence has been collected that points to the need of a new concept of coal pillar design. Two case studies will be cited to illustrate this point. 3-D US pillar strength formulae Figure 1 shows a sectional layout of a one-unit mine. The seam was about 1.3 m (50 in.) thick with a uniform cover of 64 m (210 ft). A house was located near the center of the section. The homeowner demanded that no surface subsidence and domestic well dewatering should ever be allowed as a result of underground room-and-pillar mining. Physical properties - strength and Young's modulus - of the rock strata including coal were obtained by testing small samples in the laboratory. The uniaxial compressive strength of the coal was 3660 kPa (823 psi). Using various pillar strength formulae, the homeowner recommended that square chain pillars be at least 11 m (35 ft) wide. The coal company, however, desired to pursue optimum coal recovery in the safest and most economical manner. They engaged in three-dimensional finite element analysis of the section taking into account the complete stratigraphic sequence of the overburden. Results indicated that the section can be developed by 5.5 m (18 ft) wide entries at 21 m (70 ft) center-to-center. In retreat, the pillars can be splitted along both centerlines leaving a stump pillar of 5.5 m (18 ft) square at each of the four corners. The 5.5 m (18 ft) square stump pillars still maintained a safety factor of 1.5, although the safety factors calculated by various pillar strength

Jan 11, 1986

By R. A. Jankowski, J. D. Potts

Four underground respirable dust surveys were conducted to determine factors affecting belt entry dust levels and how using belt air to ventilate work areas affected dust exposures. Belt entry dust levels on the surveyed longwall and continuous miner section averaged 0.59 and 0.26 mg/m3, respectively. The stageloader/crusher contributed an additional 0.5 to 0.9 mg/m3 of dust to belt air, while the feederbreaker contributed 0 to 0.2 mg/m3 of dust. A 1000 ft (305 m) increase in belt entry length or a 200 to 500 tons/shift (181,000 to 454,000 kg/shift) increase in production resulted in roughly a 0.1 mg/m3 increase in dust. Using the belt entry as an intake entry on the continuous miner section appeared to reduce dust levels by 0.1 to 0.3 mg/m3 during cutting. Belt air was not used to ventilate the face on the longwall section.

Jan 1, 1992

Clean Diesels fuel-borne catalyst, Platinum Plus, helps improve fuel economy for all engines up to 10 percent while reducing particulate emissions by up to 25 percent. When used with a simple diesel oxidation catalyst, particulate emissions can be reduced by 30 to 50 percent. The use of Platinum Plus enhances combustion in the cylinder, burning fuel more completely. This reduces CO2 and other greenhouse gases and lowers total operating costs by improving fuel economy.

Jan 1, 2007

By D. N. Adams, M. M. Wong, M. J. Robison

Islais Creek Contract E, a transport/storage tunnel in San Francisco, was visited on a fieldtrip during construction by delegates to the 1995 RETC. This paper is a follow-up to that fieldtrip. The project’s two tunnels are 3.7 m and 3.2 m finished diameter, 155 m and 77 m long, respectively. The contractor used 1,000 overlapping jet grout columns to pre-treat the weak Bay Mud along the tunnel alignments, then mined them with an open faced tunnel shield, eliminating the need for compressed air tunneling. This paper documents the jet grouting program and the tunneling operation used on the project.

Jan 1, 1997

By R. Snoby

Since its introduction in 2002, the modern air jig has processed a wide array of coals throughout the world. This paper explores the reasons and justifications for the installations and provides case history performance data. Specifically highlighted are air jig plants processing metallurgical coal in Colombia, bituminous coal in the United States and India and lignite in the United States and Spain. Each installation has unique reasons to justify an air jig facility. It is important to note that not all of the justifications were based on the ?most cost effective yield?, normally a mantra for coal preparation plant designers and owners. Dry jigging of coal has long been a proven technique for upgrading coal, the modern air jig, with its improved efficiency and operating systems simply extended the range of applications. In some cases, it even allows market quality coal to be produced when no other option is possible.

Jan 1, 2009

Ground falls (roof and rib) have historically been responsible for about 50% of all fatalities in bituminous underground coal mines. In some recent years, the number of ground fall fatalities has approached zero, indicating that significant progress has been made. On the other hand, last year?s Crandall Canyon twin mine disasters, in which 9 miners perished in violent coal bumps, provided a stark reminder that complacency is premature. One important success has been a great reduction in the number of miners killed inby roof supports. Throughout the 1990?s these accounted for nearly half of all roof fall fatalities, but there have just been two inby incidents in the past 5 years. Progress has also been made in pillar recovery. Safer mining technologies have reduced the number of fatal incidents, but some recent failures have underlined the need for careful management of the retreat mining process. On the other hand, more than 400 miners continue to be injured each year by rock falling from between supports, and 100 more are injured by rib falls. Together, these two categories also account for a large percentage of recent ground fall fatalities. Available technologies such as roof screen, rib bolting, and inside control roof bolters could dramatically reduce injury and fatality rates if they were used more widely. Further advances in these areas will likely be the next big advance in ground control safety. Disclaimer: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Byron T. Darnton

Gravity concentration at the Pegasus Gold/Montana Tunnels Mine, near Helena, MT, began in June 1991 when a coarse-gold-scalping circuit was commissioned. It processes a small portion of the ball-mill circulating load to reduce the risk of gold particles that are too coarse to float from advancing to flotation. The circuit also cost-effectively enhances overall gold recovery and payable gold ounces. This gravity circuit has been a major success. Since the circuit was commissioned, throughput has increased 30%. Several modifications and improvements were made during the last three years that allowed the gravity circuit to keep pace with the higher tonnage. The overall approach to gravity concentration at Montana Tunnels has always been to optimize production rather than maximize the gold ounces produced. This philosophy has now yielded a circuit expansion and relocation project. It will allow for an estimated 50% increase in gravity gold production, while significantly reducing the unit costs of production.

Jan 1, 1995

By M. S. Riyazulla

A model of a new laboratory magnetic separator has been conceived to cater the needs of process engineers and mineralogists world over engaged in mineral characterization and beneficiation. It would be essentially a laboratory instrument for the separation and concentration of various ferro and non-magnetic minerals. Based on the basic concept of Frantz Isodynamic Magnetic Separator, the new separator conceived would not only speed up the work of a process mineralogist and save the energy, but it would effectively separate and sequentially produce about fourteen fractions at a time. In the present paper, the probable operational procedures and the design have been discussed in detail for the various mining companies to assess its economic feasibility. If it could be fabricated, it would have a worldwide market The concept has been patented in author?s name in India.

Jan 1, 2009

By D. Brunner, G. R. Baiden, H. J. Yazici

System simulation is an increasingly popular technique for analyzing and improving existing as well as newly designed underground mining operations. An engineering firm that specializes in simulation helped a major metals producer build a long-range planning model of an existing underground mine. Subsequently the team adapted this model to assess technology alternatives in the design of a new mine. The two models differ in the level of detail used for modeling the development process. This paper discusses the differences in approach between the models along with the experiences gained and challenges faced during the construction and use of the models.

Jan 1, 1999

By T. Y. Yan

O2, NaCl03, H202, NaOCI and Ce+4 have been examined as oxidants in an alkaline carbonate system for uranium in situ leaching. The South Texas and New Mexico ores contained up to 2.6 meq/g of reducing compounds that consume oxidants in the leaching operation. Leaching rates did not increase linearly with the oxidation potential of the oxidants. A mild oxidant can be used to maximize uranium oxidation selectivity and oxidant efficiency. 02 can oxidize most of the uranium mineral with an adequate rate and high oxidant efficiency.

Jan 1, 1993

By Y. V. Swamy, B. Bhoi, H. S. Ray

Low-grade manganese ores with low Mn/Fe ratios can he enriched through selective carbon reduction of iron oxide to magnetite followed by magnetic separation o f the magnetite. Thermogravimetric analysis (TGA) was used to assess the preferential isothermal reduction of pure M1702 and Fe2O3 using solid carbon. This was followed by reduction of a synthetic analogue of composition comparable to an actual low-grade ore (i.e., Sandur manganese ore, Sandur, India). The carbothermic reduction of the manganese ore converts the hematite and goethite minerals to magnetite (Fe3O4), with the magnetite then going into the magnetic, fraction. The resultant nonmagnetic ,fraction becomes depleted of iron with an enhanced manganese content. These results show that it is possible to reduce the iron from 22% to 5.85%, thus increasing the Mn/Fe ratio from 1.52 to 6.2 with a manganese recovery of about 50%. The recovery was, further improved by grinding the magnetic fraction to -75 µm.

Jan 1, 1999

By A. Sullivan

Success in mining demands the creative application of equipment, systems and processes to the unique needs of each mineral deposit, market and, though often overlooked, the culture of the individual business. In recent years, domestic coal mining companies have become more attentive to the contribution safety and loss control programs have on their financial results. Although most have adopted fairly conventional safety programs, some have created systems and processes tailored to their unique circumstances. While each coal mining business must consider the typical risks inherent to our industry, excellence in safety is most likely achieved when a safety program is customized to meet the needs of the individual business.

Jan 1, 2000

By Ian Hutchison, Ted Sluder, Jack Caldwell, Don Moore

Introduction The Cannon mine at Wenatchee, WA has recently been brought into operation to recover gold from the sandstones of the Swauk formation. The mine is a joint venture between Asamera Minerals (US) Inc. and Breakwater Resources. A tailings impoundment was constructed to impound 2.7 to 3.6 Mt (3 to 4 million st) of tailings at 1.8 kt/a (2000 stpd) over about five years. This paper describes the design and construction of the impoundment. In particular, it describes the 100 m (300 ft) high earthfill embankment that is the main feature of the facility. Project environment The project is located on the outskirts of Wenatchee, a town of about 40,000 people. The town is situated on the flat alluvial terraces beside the Columbia River. The Cascade Mountains rise from the terraces in a series of ridges and valleys. The mine is at the foot of the Cascades. The tailings impoundment is in one of the steep valleys. The climate is mild and dry (Table 1). Site selection Twelve alternative sites within a 16-km (10-mile) radius of the mine were examined. Decision making theory was used to select the most suitable site. Advantages of the chosen site include its proximity to the mine and its low visibility from points of common public access. Also, the area was already heavily impacted by an existing silica quarry. The major disadvantage of the site is the need to pump tailings over a distance of 1.5 km (1 mile) and against a static head of 200 m (655 ft). Also, it is located in a gulch just upstream from the town of Wenatchee. Site geology The impoundment is generally underlain by interbedded sandstones and siltstones. The siltstones are often shattered. The sandstones are often friable. Both rock types are extensively jointed. Some isolated faulting of the sediments occurred before the area was covered with basalt flows. About 10,000 years ago, at the end of the ice age, the basalts were covered by 3 to 10 m (10 to 33 ft) of wind blown loess - a fine sandy clay and silt. River deposits filled the base of the valley to depths between 5 and 25 m (16 and 82 ft). Under the main part of the embankment, these materials were removed to expose bedrock. Ground water flow is generally through the more permeable layers. The permanent water table is about 5 m (16 ft) beneath the ground surface. Project and impoundment layout Figure 1 shows the layout of the mine, the mill, and the tailings impoundment. The tailings deliv-

Jan 8, 1986

By M. Haase

[ ] How important is a robust communications system for your mine site in order to meet operational and safety requirements? Do you currently have VSAT in place and need a low cost, high quality multi-line VoIP phone system at the site? By adding a single, compact piece of hardware, you can utilize your existing satellite internet connection and have as many as twenty-four separate phones lines from a single unit. The platform is scalable for any size of operation and can be implemented above or below ground.

Jan 1, 2012

By E. Tulcanaza

M.S. Azun I do not at all agree with the basic points of the author's conclusion. The use of lognormal or normal model to respond to the attribute distribution function should be carefully questioned. If fitting a distribution function of regionalized variables is the main purpose, one may employ one of certain well-known families of distributions, such as Tukey's lambda functions. For instance, the distribution function of gold assay values studied by Krige (Krige, 1978) may fit the lognormal model well, but one should not exclude that the basic idea of using the distribution function of observed data is to have insight of the physical mechanism that gives rise to the regionalized variables. In Applied Geostatistics, there are many examples considering only lognormal or normal model for the distribution function of geostatistical data even if the observed distribution function has more than one mode. Of course, using lognormal or normal model always brings easy computation for the statistical properties of attribute under investigation. Still, I object to adopting any of those models without having any "statistical inference." As seen from the author's paper, lognormal and normal model produce the same average grade (0.746% copper) and almost the same sample variance. Therefore, which model explains the probabilistic behavior of ore deposit is always an important question that should be replied by the geostatistician using not the common sense but the statistical and probabilistic methods. For kriging procedures, such as linear kriging, one should describe either second order stationary properties or bivariate properties of regionalized variables. Second order properties, such as correlogram function or semivariogram function, are the inputs of the so-called kriging equations. Selecting one of any useable models for the observed second order properties, such as spherical model, is not easy since the models are not based on the correlations structure of the regionalized variables. How those models being used in Applied Geostatistics can be distinguished is another important problem. One may develop many fitting models to respond to the observed second order properties of regionalized variables. However, I suggest that the model should be based on the probabilistic behavior of geologic process. The author used spherical model for copper, wolfram, and silver grades from isotropic sector (Fig. 2, 4, 3b) and exponential model for silver grades obtained along raises in isotropic sector (Fig. 3a). It seems that those semivariograms given in Fig. 3b for isotropic sector and Fig. 4 may be described by the random model implying that regionalized variables do belong to renewal process (Azun, 1983). If I knew the total number of data points used in estimation, I may prove that my conclusion is correct. Recalling the test for the first order sample correlogram value, the test procedure is introduced such that the independence is rejected if [ ] where Za/2 is the a/2 percentile of standard normal random variable and N is the total number of samples used in estimation (Azun, 1983). For the other observed semivariogram functions I suggest the author might try to use the so-called "Markovian model" describing not only the correlation structure of regionalized variables, but also the physical mechanism that produces the regionalized variables. The Markovian model for correlogram function is, [ ] The Markovian model for the other second order properties of ReV are also derived. T ve B, in the above equation, show, for example, structural change and mineralizational variation in a considered deposit, respectively (Azun, 1983). In selecting any model, it is not easy to search for the "best" response to the observed second order properties of ReV's. The Markovian model, based on a theoretical understanding of underlying mechanism, gives more information about the occurrence of regionalized variables and respond to all properties. Random model and the so-called hole effect structure can be easily defined as a special form of the Markovian model (Azun, 1983). An estimation of any second order properties of regionalized variables may be computed through (N-1) lag. However, the dependency between the regionalized variables may be deemed to have "died out" after the so-called stationarity width (range). In practice, the estimation is carried out through 25% of the total number samples available. Therefore, the large fluctuations around the zero level and variance for correlogram or covariogram function and semi-variogram function, respectively, cannot be observed. Since the number of pairs involved in the estimation of higher second order properties is small, the estimation variance at those lags is large. There is no need to show higher order estimated second order properties. After using one of any kriging procedure for block estimation, the distribution function of average grades has the same mean as the drilling sample grades but

Jan 3, 1985

By A. L. Crandell

History The Cortez Mining District has a long history of mining activity dating back to 1862. More recently, Cortez Gold Mines had operated a cyanide leach, counter current decantation (CCD) recovery gold mill from January 1969 to February 1976. This type of plant has been standard in the US for treating higher grade, finely disseminated gold in Carlin type ores. The mill was initially operated from 1969 to 1973 at 1.5 kt/d (1650 stpd) on oxidized ore from the Cortez ore body. In 1973, the mill was operated at 2 kt/d (2200 stpd) on softer, less oxidized, high clay ore from Gold Acres, located 13 km (8 miles) west of Cortez, NV. In February 1976, the oxidized portion of the ore body at Gold Acres was depleted and the mill ceased operations. Successful heap leaching of the lower grade portion of the ores was practiced at both Cortez and Gold Acres to supplement the milling operations. Valuable experience was gained in the operation of these two heap leaching programs (Duncan and Smolik, 1977). The ore heaps at Gold Acres and Cortez were releached with a limited crew from 1976 to 1979. The surge in the price of gold in late 1979 sparked an interest to incorporate new techniques into treating lower grade and less oxidized carbonaceous ores at Cortez. In early 1980, heap leaching was started on low grade oxidized dump material left from the earlier Cortez mining operation. By June of 1980, testwork was completed on the London Extension Dump, a low grade, mildly carbonaceous dump at Gold Acres. It was decided to convert the mill at Cortez from the conventional cyanide leach CCD recovery plant to a carbon-in-leach (CIL) recovery system. In May 1983, ore processing from the Horse Canyon deposit began. The Horse Canyon ore body contains both oxide and carbonaceous ores and is located 22.5 km (14 miles) from the Cortez mill. The Cortez CIL circuit was expanded to handle a blend of oxide and carbonaceous ores from Horse Canyon. Ore selection In the last quarter 1979, gold prices were increasing to a point where restarting the Cortez mill, idled since 1976, appeared imminent. Several previously explored geologic reserves at various stages of development were available as possible sources of feed for the mill. Initial metallurgical testing of dumps and tailings from earlier operations was completed, and previously uneconomic deposits were explored. It was decided to pursue sources of ore with the least lead time to production and those with the least capital cost requirements. A master plan was developed to bring the four profitable ore resources into production. The plan called for: • Heap leaching of waste dumps from the Cortez mining operation; • Restarting the mill to handle the waste dumps from the London

Jan 9, 1986

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012

By S. K. Singh, P. R. Sheorey

To meet increasing demand of coal, underground mining is largely being replaced by the exploitation at deeper horizons and with greater complexities. The exploitation-proposition may be below not-to-be-disturbed surface properties or below water-bodies, posing a constant threat of inundation. Also, the mounting pressures to limit the adverse impacts on the environment bring the extraction-undertaking to face more challenges. An understanding of subsidence-mechanism and a rational quantification of subsidence parameters is a requisite herein. This paper presents such pragmatic quantification, validated at mine-sites in India. In comparison, better productivity, conservation and safety is ensured in this approach.

Jan 1, 1999

By Tianzu Yang, Weifeng Liu, Lin Chen, BOYI XIE, DUCHAO ZHANG, HUI XIAO

In this study, the oxygen-rich bath smelting process of copper dross was simulated using Factsage software. It was found that the two-step simulation results agreed better with the industrial data, especially in the speiss. Bismuth (Bi), lead (Pb), antimony (Sb), arsenic (As) and copper (Cu) contents in the speiss by two-step simulation differed from the industrial data by 0.6, 0.8, 2.6, 7.2 and 8.6 weight percent, respectively. The two-step simulation results indicate that the speiss partitioning of Sb, As and Cu increased from 60.1, 32.3 and 27.5 percent to 81.6, 67.8 and 47.2 percent, respectively, with the smelting temperature increasing from 1,050 to 1,250 °C, while the metal partitioning of Sb and Cu increased from 0 and 2.7 percent to 15.2 and 13.3 percent, respectively, with the separation temperature increasing from 400 to 700 °C.

By E. Bauer, S. Moore

Technological advances in underground coal mining have led to a reduction in fatalities. This study demonstrated that the percentage of cumulative injuries remained largely unchanged across two decades of technological advances (1983-1984: 37%; 2003-2004: 33%). Furthermore, it was demonstrated that the average number of lost days due to cumulative injuries has increased (36±55 days and 62±82 days, respectively) which may have been due to the increased age of the work force or an increase in length of employment meaning that the mine workers injured in 2003-2004 had been exposed to ergonomic risk factors longer than those in 1983-1984. It is recommended that ergonomics processes be implemented as a means to systematically identify, prioritize, and resolve the root causes of these cumulative injuries.

Jan 1, 2007