Search Documents

By Bruce Clements

The Bagdad mill, located near Bagdad, AZ, was built in 1977 with a designed mill capacity of 36.3 kt/d (40,000 stpd). An autogenous mill-ball mill crusher (ABC) grinding circuit was chosen. The original mill contained three independent grinding circuits. Each contained one 9.75m-diam x 4-m-long (32-ft-diam x 13-ft-long) fixed-speed autogenous mill, a4.7-m-diam x 6.7-m- long (15.5ft-diam x 22-ft-long) ball mill and one 2. 1-m-diam (7-ft-diam) short head cone crusher. Total installed power per grinding circuit was about 8.4 MW (11,350 hp), with 5.9 MW (8000 hp) in the autogenous mill, 2.2 MW (3000 hp) in the ball mill and 261 kW (350 hp) in the crusher (Fig. 1). The autogenous mills were designed to be able to operate semi-autogenously. However, they were never converted to semiautogenous grinding (SAG) mills. As a result of this design, only about 4.1 MW (5450 hp) of the designed power is used in the autogenous mills. The grinding circuits are closed, with 2.4 x 6 m (8 x 20 ft) double-deck vibrating screens. A series of conveyors re- turn screen oversize underneath the mill coarse ore stockpile to feed the crushers. Variable speed belts feed the crushers and control power draw. Crusher product reports directly to the tail end of the autogenous mill feed belt (Fig. 2). A magnetic sensor detects tramp iron in the autogenous mill-crusher circuit.

Jan 1, 1992

By George Watson, Gu Quanzhong, S. Gerard Sawyer

Bulkheads, also known as hydraulic seals, are used to seal abandoned workings and protect adjacent active mines from explosion and control unwanted inflows of water from poorly sealed shafts, water-bearing strata, and abandoned mine areas or gobs (1). At coal seam outcrops, bulkheads have typically been used to prevent access and to control acid mine drainage. Bulkheads have also been installed at outcrop openings located within the footprint of an embankment dam, or within the reservoir of an impoundment, to prevent stored water or slurry waste from flowing into active or inactive underground mine workings (2). Components of MICON Bulkhead Seal MICON bulkhead seals in mining applications refer to seals designed to impound liquids or slurry. The MICON bulkhead seal is comprised of two concrete block walls set in the front and back and a polyurethane/aggregate core (Figure 1). The two walls are usually dry-stacked, surface-bonded walls constructed with solid load-bearing concrete blocks (ASTM C90) or concrete building brick (ASTM C55). The surface bonding material used in the wall construction must be MSHA-approved. The type of stone, if any, used to fill the space between the walls is not essential. However, MICON generally uses No. 57 limestone in 50 lb. bags, specified to moisture control, shrink-wrapped and palletized. The polyurethane foam used in the construction of the bulkhead seal is engineering specified and formulated by density based on the optimization of cost, seal core thickness, required adhesive strength, the use of stone filler and other required physical properties.

Jan 1, 2005

By Felicity Lloyd, Stuart Kearns, Roger McLimans

The metamorphic terrane of southwestern India is a geological environment containing ilmenite source-rocks, transport drainage systems, and resultant beach sand deposits that contain altered ilmenites greater than 60wt% TiO2. As such, this environment provides a geological laboratory, from source to deposit, for the investigation of ilmenite origin, alteration, and geochemical character. Ilmenite samples from potential source rocks, river sands, and beach sands all show degrees of alteration and a variety of alteration textures (iron leaching) producing leucoxene (here defined as >70 <90wt% TiO2) and progressing to rutile (here defined as >90wt% TiO2). Distinct alteration textures are specific to different source rocks and are used together with trace element geochemistry as provenance criteria. Ilmenites are classified on the basis of their trace element content. In India, the ilmenites are classified principally according to the Mg, Nb, and Mn content and this signature defines potential source rocks, even where the ilmenite is altered to a TiO2 content of 70wt%. The trace element data may fingerprint source rocks whose ilmenite is more prone to iron leaching and that criterion has application in exploration for higher-grade ilmenites.

Jan 1, 2005

By I. Gombköto, J. Bohm

"In Europe, and therefore in Hungary opening a new mine is harder and harder. Depletion of mines, unfavourable legal and economic changes, and growing public concerns are the main reasons. Social and economic interests require total utilization of mineral raw materials of the operating mines, and furthermore utilization of waste heaps of the former mines. There are 5-6000 waste heaps of the operating and the closed mines in Hungary. 2000 of these waste heaps have already been estimated, and researches show that total amount of waste heaps can be calculated to 1 billion tones. These researches left out of consideration waste heaps exploited and placed in deep lignite mining. In several projects and researches we analysed processing of waste heap and possibilities to use its components. A processing technology for utilizing waste heaps has been developed based on laboratory and pilot plant tests. Great amount of useful materials of quarrying waste heaps can be utilized with this technology. Tests were also done for processing waste heap of a former ferrous metals mining. The developed processing technology contributes to use these waste heaps as aggregate for cement industry, as dielectric and aggregate for construction. The essay presents in details main characteristics of waste heaps, technologies already used for processing waste heaps of quarrying and ferrous metals mining, mass balances and qualitative parameters of the end products."

Jan 1, 2011

By L. M. Anisdahl

Ventiflex is a flexible ventilation duct system with a global market within mine and tunnel ventilation. The system is distributed in a wide range of qualities and dimensions. It is very important that ventilation systems are designed correctly in mines and tunnels. An incorrectly dimensioned system might result in bad air quality and too high costs. The objective of this study has been to assess some important design parameters for ventiflex comprising the friction loss factor for the duct wall itself, as well as the shock loss factors and the leakage factors for the different couplings systems. This has been obtained by carrying out a large scale experimental program on ducts with all the three different couplings: Velcro, zip and steel-ring. Pressure profiles and air flow rates have been measured, and based on these data the different factors have been calculated. The following results have been obtained: A friction factor l = 0,012 (K = 10) for the duct wall, a shock loss factor z = 0,0125 for velcro- and zip couplings, a shock loss factor z = 0,005 for steel-ring couplings, and a leakage factor f* = 0 mm2/m2 for all three coupling types. The latter result proves that no leakage is possible for a correctly installed duct with proper alignment. The results also confirm that ventiflex complies with class S, or better, according to the SIA-norm. However, whether ventiflex should be designed as class S, A or B according to the SIA-norm, depends on the particular application.

Jan 1, 2009

By Steven W. Hunt

Appropriate seals, portal ground improvement, and compatible shaft construction techniques are vital elements for launching and receiving tunnels effectively in urban areas where adjacent property requires protection from excess ground movements. This paper focuses on seals and ground improvement along with shaft wall types, required to launch or receive tunnel boring machines within wet, permeable ground at the portal zone. The paper also discusses probing to verify suitability before the tunnel eye is cut. Methods addressed include: rubber gasket seals; soft eyes; double walls; top hats for reception; and, portal zone ground improvement (permeation grouting, jet grouting, un-reinforced slurry diaphragm wall panels, ground freezing, deep soil mixing, dewatering, and over-excavation and backfilling). This paper focuses on challenges with launch and reception of pressurized-face TBMs with precast concrete segment linings. Challenges related to pipe jacking are discussed in a separate paper titled ?Mitigating Microtunnel Launch and Reception Challenges? (Hunt and Finney 2008).

Jan 1, 2008

By Bruce Gellar

For the past six years, the author has made it a priority to attend the Prospectors and Developers Association of Canada’s (PDAC) annual conference. This most recent meeting took place March 10-13, 2002in Toronto, Ontario. In the three years since the author’s last PDAC report, the mining industry has undergone a severe trough. Some the industry’s woes included deeply discounted commodity prices, rampant layoffs, mergers, and overall avoidance by the investment community. However, at each of the PDAC conferences, the author has felt a heightened sense of excitement about the mining industry, more so than at other similar gatherings.

Jan 1, 2002

By Daniel Saint Don, Jacques Dumouchel

QIT Madagascar Minerals (QMM)’s heavy mineral sand deposit located near the Village of Fort Dauphin, Madagascar was recently drilled using Boart Longyear Company’s Mini-Sonic drill. Continuous sand core samples were obtained to a depth of up to 30 meters for analysis and compared with the existing drilling data. Results were used as part of a validation process of the resource estimate, based on approximately 1,500 exploration holes drilled to date.

Jan 1, 2005

By Kwang ‘Min’ Kim, Paul T. Behum

The Old Bevier Aerobic Wetland in Macon County, Missouri, was constructed between 1990 and 1991 by the Missouri Department of Natural Resources’ Land Reclamation Program for the purpose of treating acid mine drainage (AMD). The principal source of the AMD is from an underground mine that operated during the 1920&apos;s through 1950&apos;s, which was partially exposed during surface mining in the 1960’s. Limestone bedding of an AMD collection system provided alkalinity similar to an anoxic limestone drain (ALD). Because the original aerobic wetland failed when a critical dilution water supply became unavailable, the total acidity of the AMD overwhelmed the limited neutralization ability of the aerobic wetland. The aquatic vegetation deteriorated and treatment became ineffective. The Missouri Land Reclamation Program with the assistance of the Office of Surface Mining, Mid-Continent Regional Coordinating Center rehabilitated the Old Bevier Aerobic Wetland in 2001, incorporating newer technologies to improve the performance. The new system, Old Bevier II treatment facility, consists of a 2-stage vertical flow pond (VFP) with associated oxidation cells and aerobic wetlands. This paper discusses the performance of this passive AMD treatment system, updating an earlier report. The new treatment system has operated with nearly continuous net alkaline discharge and a high iron removal rate. Treatment improves during warm months when emergent vegetation is fully established and biologic activity is greater. Reduction in system efficiency is evident during winter months.

Jan 1, 2005

By W. Langer

Of the 50 or so most often utilized industrial minerals, more than two thirds are, or have been, produced in the western states of Arizona, Colorado, Idaho, Kansas, Montana, Nebraska, New Mexico, North Dakota, Oklahoma, South Dakota, Texas, Utah, and Wyoming. Some commodities, such as natural aggregate, currently are produced in all 13 states; others such as beryllium and iodine are produced in only Utah and Oklahoma, respectively. Together, the 13 western states make a significant contribution to the US industrial minerals industry.

Jan 1, 2007

By R. K. McLimans, C. Knudsen, S. Bernstein, D. Frei

Computer Controlled Scanning Electron Microscopy (CCSEM) is used to analyze indivdual mineral fractions in heavy mineral sands. CCSEM is a fully automated particle analysis technique for the determination of physical and chemical properties of a large number of individual particles. CCSEM enables the precise and accurate determination of the modal abundances of individual mineral fractions (e.g. ilmenite, rutile, zircon, or garnet), their average chemical composition (and compositional variation), as well as their physical properties such as size (e.g. diameter and perimeter length) and shape (aspect ratio and circularity). A unique sample preparation procedure is used to produce representative polished sections from cylinders of raw sand samples such that thousands of grains are present in a polished cross section, but grains are not touching. The combination of this sample preparation technique with CCSEM enables the fully automated analysis of individual grains without the application of de-agglomeration or erosion steps to separate touching particles. Hence, CCSEM yields information representative of the entire area of analyzed grains without systematic bias due to neglect of rim areas by de-agglomeration or erosion steps. Therefore, the resulting data are determined with high accuracy, precision and statistical validity. Because the sample preparation is relatively straightforward, using raw sand samples, and all chemical and physical properties are determined in one analytical session per sample, CCSEM is a powerful cost and time efficient tool for characterizing chemical and physical properties of minerals in heavy mineral sand deposits.

Jan 1, 2005

By M. P. Valoski

Mine fires and/or explosions continue to occur. While these are unusual events, they comprise emergency situations. Whenever one of these events occurs, the Mine Safety and Health Administration (MSHA) responds with specially trained teams, mine fire experts, sophisticated scientific instrumentation, and trained instrument operators. In order to analyze mine air samples on-site, because time is of the essence, MSHA has a Mobile Gas Laboratory. The laboratory, which is stored near Pittsburgh, is totally self-contained. Sending air samples to a laboratory would take too long. Mine fire experts need the results of the latest analyses as soon as they are finished. The mobile laboratory is housed in the box of a diesel truck. Benches line both sides of the laboratory. Gas chromatographs are mounted on the benches. There is sufficient bench space for multiple bench top gas chromatographs. These instruments and their controllers are shock and vibration isolated to protect them during transit. The mobile laboratory can operate using on board diesel generators or line power. An uninterrupted power supply (UPS) supplies power to the instruments while switching from generator to line power or visa versa. Therefore, analysis of samples can proceed without interruption if a power failure would occur. In the rear of the mobile laboratory are racks that hold compressed gas cylinders. These cylinders contain carrier gas and compressed air. An air compressor is housed under the laboratory to operate the gas chromatograph actuators. Within several hours after arriving at a mine the instruments have stabilized and have been calibrated. The mobile laboratory is ready to begin analyzing air samples. The mobile laboratory has proved itself at many mine fires and explosions since its purchase.

Jan 1, 2009

By John Reilly

Costs of complex/underground projects have been consistently underestimated and delivery on time and on budget has been problematic. This has been attributed, to inadequate cost estimates and unidentified and/or insufficiently managed risk. Use of probabilistic cost estimates like the Washington State Department of Transportation?s CEVP® process (developed by the author and others) has produced more realistic cost estimates, explicitly identified and quantified risk (as input to risk management plans) and early awareness of key project issues. This paper updates previous work (NAT 2004), adds implementation detail for probalistic cost estimating as used by WSDOT, FHWA and other agencies and will address key issues in risk management, as related to probalistic cost estimates.

Jan 1, 2008

By H. Fayed

Two-phase (water and air) flow in a self aerated WEMCO flotation machine has been investigated using computational fluid dynamics (CFD). A 0.8 m3 model is considered. The flow is modeled by Euler-Euler approach, and transport equations are solved using a commercial software ANSYS-CFX5 [1]. Because of the lack of circumferential periodicity in this machine, the entire machine is modeled and unsteady simulations are conducted in the whole volume of the bulb. Uniform bubble diameter is specified, and the effects of bubble diameter are determined by conducting simulations for three diameters of 0.5, 0.7, and 1.0 mm. The unsteady air flow rate through the machine is predicted as an outcome of the simulations. Air volume fraction contours and velocity field in different parts of the machine are presented and discussed.

Jan 1, 2012

By M. Fustic, A. H. Paul

The geology of the Muskeg River Oil Sands Mine is described to demonstrate how geologic modeling aided in resource evaluation and material characterization during the feasibility and construction stages. Bitumen is hosted in the clastic sediments of the Cretaceous McMurray Formation which is informally divided into members representing the fluvial, estuarine and marine environments of this transgressive sequence. Lithofacies mapping of drill core provides further detail to classify materials as resource type, for extraction suitability and for construction suitability. Geologic interpretation provides tools for the engineers to produce effective mine plans and for the operators to execute them during mine development.

Jan 1, 2002

By Joe Roby

Rolling disc cutters are the business end of hard rock and mixed face tunnel boring machines (TBMs). Since their first successful employment on a TBM over fifty years ago, disc cutter technology has constantly evolved, allowing modern TBMs to excavate very hard and abrasive rock efficiently. Disc cutters have also been employed successfully on earth pressure balance (EPB) and slurry machines, cutting rock under water and ground pressure. The range of materials excavated by machines today is broader, excavation rates higher and cutter costs lower than ever before, proving the value of investment in cutter development. This paper describes recent improvements in disc cutter components including cutter ring materials and processing, as well as improvements in lubricants, bearings, seals and cutter condition monitoring. These developments have resulted in more reliable cutters capable of operating in a wide range of geological conditions. Ultimately these improvements result in a better value for both contractors and project owners.

Jan 1, 2008

By E. Topuz, C. Patrick

Longwall face-to-face transfers can cost more than $100 per minute in lost production potential and $100,000 for personnel and supplies. Such high costs make extensive planning and control of the transfer process a critical necessity for the economic feasibility of longwall operations. Operations research techniques are used for the analysis and modeling of longwall face-to-face transfers. Transfer data has been collected from companies who operate, over 35%, of the total US longwall faces. Comprehensive sequence networks of existing longwall transfers were developed; simulation was used to generate models of transfers under Carving conditions; and the economic feasibility of tine-cost tradeoffs in the transfer procedure was investigated.

Jan 1, 1994

By Don C. White

The Vulture mine near Wickenburg, Arizona was a major gold producer from 1863 to 1942, having yielded about 11t(12.1 st) Au and 8t (8.8st) Ag. Gold occurs as coarse native metal and electrum in quartz veins and also finely dis¬seminated within a quartz monzonite sill and its silicified wall rock. The sill is semi-conformable within a Proterozoic volcaniclastic-dominated sequence, all dipping north about 35°. Early mining focused on the vein-hosted gold, particularly in the immediate hanging wall and footwall of the sill. Later efforts included some open-pit mining of the outcropping sill and adjacent altered and mineralized rock. Two sets of post-mineral faults have complicated the orebody geometry. The sill is a 350 m (1148 ft) long apophysis from a quartz mozonite stock to the west of the mine area. The stock has been dated at 85 my and contains abundant lesser gold occurrences in its core and about its margins. The Proterozoic rocks are notably lean in precious metals except where altered in proximity to the Creataceous stock and sill. Circumstances dictate an interpretation of epigenetic mineralization related to the Laramide intrusion.

Jan 1, 1990

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By D. Nutakor

The ability of computers to create synthetic representations of the real world in virtual reality offers a number of opportunities to enhance training methods used in the mining industry. Unfortunately, the training effectiveness of virtual reality systems currently used in the mining industry has received only limited testing. Miner Simulation (MinerSIM), an augmented reality system with integrated hypermedia suitable for training underground miners in the basics of using a jackleg drill to install rock bolts in a virtual mine environment is in its evaluation process at the University of Missouri-Rolla Experimental Mine. This paper discusses evaluation methodologies of the MinerSIM system, which consists of experimental and control groups with control students learning via traditional lecture and text formats. Preliminary results from usability tests of the first part of MinerSim, which is an online tutorial on underground rock bolting, are presented.

Jan 1, 2008