Search Documents

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Alejandro Gutiérrez, David Ahues, Paola Merino, Felipe González

A Discrete Elements Method (DEM) study of load movement within a SAG mill 12,192 × 7620 (40′ × 25′) in normal operating conditions is performed. The purpose is to determine how the geometry of the lifters affects the kinetics of the load inside the mill. Specifically, the changes produced by the incorporation of inclined lifters and spiral or helicoidal pulp lifters to the kinetics are evaluated. Four study cases are identified: first, the base case corresponds to a conventional geometry; the second case corresponds to inclined lifters incorporation; third case corresponds to a mill with helicoidal discharge; and the fourth case corresponds to a mill with inclined lifters and helicoidal pulp lifters. To save computational resources, the water that enters the mill has been modeled by varying the coefficient of restitution. The results of a series of experiments are presented to determine how this coefficient varies when having impacts on surfaces with different liquid levels. A comparative analysis is made of the following variables: mean transport speed and material flow, for normal operating conditions. Taking as reference the mill with straight lifters and radial pulp lifters (case 1), the case with the inclined lifters and radial pulp lifters increases the material discharge flow less to 76 mm of size by 5.1%, and this value increases even more when the helicoidal pulp lifters are incorporated reaching a 58.6%. The most significant change is seen in the flow through the grates and the pulp lifters discharge, which can increase substantially improving the operation.

An incremental analysis based stope design optimization method was developed at Exodus, an underground project located 30 miles north of Carlin, Nevada. Traditional underground stope design methods, by manually drawing stope shapes, are typically very time-consuming and lacking of consistency and accuracy. For quick reserve calculation and economic analysis, a new method named '3D Incremental Analysis based Stope Optimization' was created for mine wide stope designs at Exodus. With this unique but practical method, multiple options of mine designs were completed within a short period time, which allowed us to select the optimal cutoff grade and best stope design option for the project.

Jan 1, 2012

By Bertram Price

Libby, Montana is the site of a large vermiculite deposit that was mined between 1920 and 1990 to extract vermiculite for commercial applications such as insulation, gardening products, and construction materials. The Libby vermiculite deposit also contains amphibole minerals including tremolite, actinolite, richterite, and winchite. Historically, Libby mine workers experienced high exposures to amphibole structures, and, as a group, have experienced the health consequences of those occupational exposures. It has been suggested that Libby residents also have been and continue to be exposed to amphibole structures released during the vermiculite mining operations and therefore are at increased risk for disease. The Agency for Toxic Substance and Disease Registry (ATSDR) conducted two epidemiological-type studies of residents living in Libby and the surrounding areas to assess these risks. The Environmental Protection Agency (EPA) collected and analyzed exposure data in Libby and used those data to project risks of asbestos-associated disease for Libby residents. The EPA has placed the Libby Asbestos Site, which includes the mine and the town of Libby, on its National Priority List of hazardous waste sites in need of clean up. This article presents a review of the exposure studies conducted in Libby and an analysis of health risks based on the data collected in those studies. Libby mine workers have experienced elevated levels of asbestos-associated disease as a consequence of their occupational exposures to amphibole structures. Libby residents? exposures typically are substantially lower than mine workers? historical exposures, and the health risk projections for residents are, accordingly, substantially lower. © 2007 Published by Elsevier Inc. Keywords: Libby; Montana; Vermiculite; Amphibole minerals; Asbestos; Asbestos-associated disease

Jan 1, 2007

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

By John Marsden, Mike Botz

A variety of modeling techniques can be utilized to forecast metal production at heap leaching operations. These approaches reflect a wide range of complexity, flexibility, time to implement, cost, and accuracy. For many operators, a spreadsheet-based modeling technique is attractive since the calculations are directly accessible, models can often be developed by site staff, and the results are generally easy to extract and interpret. The authors have developed a spreadsheet-based modeling technique that provides a high degree of flexibility, while still considering detailed operating information for ore properties, leach kinetics, scaleup factors, lift height, and in-heap metal inventories. The technique involves establishing kinetic leach curves for each ore type to characterize metal extractions, followed by application of separate metal recovery curves to define the rate at which leached metals exit the heap in pregnant solution, taking into account delays due to the in-heap solution inventory. At any point in time, the difference between total metal extracted and total metal recovered is equal to the in-heap inventory of the leached metal. This modeling technique is particularly useful for larger multi-lift heaps where delays in metal recovery are appreciable due to in-heap solution holdup. The technique is also applicable to sites with multiple heaps, leach cycles, and/or metal recovery plants (e.g., carbon columns for gold; solvent extraction for copper). This paper describes the modeling technique, including input data required and methods for defining kinetic leach curves and metal recovery curves. The technique is compared against an alternative spreadsheet technique using a simplified in-heap solution inventory calculation to forecast metal production, which has proven to be effective at a number of sites.

Sep 3, 2019

By Neil White

South Africa (SA), a country in which all three commercially important asbestos minerals have been mined and milled, has retained proven cases of mesothelioma linked with environmental exposure to asbestos. This study illustrates the importance of fiber type in the occurrence of environmental mesothelioma. Four studies have reviewed the source of occupational or environmental asbestos exposure in 504 histologically proven cases of mesothelioma in South Africa. One hundred and eighteen cases (23%) were thought to be related to environmental exposure to asbestos. In the vast majority of these cases, exposure was linked to crocidolite mining activities in the Northern Cape Province. Two cases were thought to have occurred in relation to amosite and Transvaal crocidolite exposure in the Limpopo Province. In the balance of cases there was some uncertainty. No cases were reported with exposure to South African chrysotile. Consequently, in the vast majority of cases of mesothelioma, environmental exposure to asbestos occurred in the Northern Cape Province, in proximity to mines, mills and dumps where crocidolite was processed. Crocidolite appears to be far more mesotheliomagenic than amosite, and chrysotile has not been implicated in the disease. This is true for both occupationally and environmentally exposed individuals. ©2007 Elsevier Inc. All rights reserved. Keywords: Crocidolite; Mesothelioma; Chrysotile; Amosite; South Africa

Jan 1, 2007

By İbrahim Çınar, Hakan Özşen

Mine workers in heavy and dangerous work are under several physical risk factors, for example temperature, humidity, noise, vibration, lighting and air velocity. Thermal comfort includes parameters such as air temperature, air humidity, air flow rate, radiant heat, metabolic rate and garment insulation. In this study, thermal comfort conditions were evaluated using thermal comfort indices defined as predicted mean vote (PMV) and predicted percentage dissatisfied (PPD) which were determined by measurements taken from an underground coal mine for approximately 100 days. Although the metabolic rate (light work) was kept at 2 met, it was found that predicted mean vote ranged between − 2.58 and 1.68. The predicted percentage dissatisfied index was found to reach 95%. According to the results, it can be seen that thermal comfort may have negative effects on occupational health and safety. The change in thermal comfort index values in the Soma Underground Coal Mine was investigated in detail and the reasons for the changes were determined. Furthermore, determining the optimal working environment for the mine workers was also an aim of this study.

By J. Drelich, M. Pawlik

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size, and distribution of mineral inclusions in coal, on its wettability are briefly reviewed.

Jan 1, 1999

By L. Yuan, J. H. Rowland, D. Bahrami, R. Thomas

Blasting is the main method of production in many non-coal underground mining operations and produces multiple toxic gases as a result. The Mine Safety and Health Administration (MSHA) requires mine operators to measure the level of toxic gases in mines as frequently as necessary to ensure they are below regulatory safety limits. The current practice uses portable gas monitors to check the concentrations of toxic gases after a fixed post-blast time. This paper studies the application of a gas monitoring system in the return entry of a limestone mine to determine a safe re-entry time. The National Institute for Occupational Safety and Health (NIOSH) conducted such a monitoring program in a limestone mine from September 2016 through May 2018. NIOSH/PMRD (Pittsburgh Mining Research Division) is endeavoring to develop workplace solutions to improve detection of and reduce the risk of hazardous conditions. This study showed that the use of gas monitoring in the return air can be a useful tool at the mine operator’s disposal to detect and reduce the risk of hazardous conditions and also to reliably estimate the re-entry time.

By Richard Wilson

In the early 1970s, it became a concern that exposure to the mineral fibers associated taconite ore processed in Silver Bay, Minnesota would cause asbestos-related disease including gastrointestinal cancer. At that time data gaps existed which have now been significantly reduced by further research. To further our understanding of the types of airborne fibers in Silver Bay we undertook a geological survey of their source the Peter Mitchell Pit, and found that there are no primary asbestos minerals at a detectable level. However we identified two non-asbestos types of fibrous minerals in very limited geological locales. Air sampling useful for risk assessment was done to determine the type, concentrations and size distribution of the population of airborne fibers around Silver Bay. Approximately 80% of the airborne fibers have elemental compositions consistent with cummingtonite-grunerite and the remaining 20% have elemental compositions in the tremolite-actinolite series. The mean airborne concentration of both fiber types is less than 0.00014 fibers per milliliter that is within the background level reported by the World Health Organization. We calculate the risk of asbestos-related mesothelioma and lung cancer using a variety of different pessimistic assumptions. (i) that all the non-asbestos fibers are as potent as asbestos fibers used in the EPA-IRIS listing for asbestos; with a calculated risk of asbestos-related cancer for environmental exposure at Silver Bay of 1 excess cancer in 28,500 lifetimes (or 35 excess cancers per 1,000,000 lifetimes) and secondly that taconite associated fibers are as potent as chrysotile the least potent form of asbestos. The calculated risk is less than 0.77 excess cancer case in 1,000,000 lifetimes. Finally, we briefly review the epidemiology studies of grunerite asbestos (amosite) focusing on the exposure conditions associated with increased risk of human mesothelioma. © 2008 Elsevier Inc. All rights reserved. Keywords: Risk; Fibers; Particles; Taconite; Asbestos; Exposures

Jan 1, 2007

By Malcolm Ross

The Reserve Mining Co., in the processing of taconite iron ore quarried from the Peter Mitchell Pit, deposited the finely crushed waste rock into Lake Superior near Silver Bay Minnesota. In the early 1970s The U.S. Environmental Protection agency filed a lawsuit against Reserve Mining Co., asking the court to force the company to stop dumping into the lake. On April 20, 1974, after a lengthy court battle, the U.S. District Court concluded that the Reserve Mining discharge into Lake Superior violated federal and state pollution laws and thus ordered Reserve Mining Co., to halt the lake disposal of taconite tailings. At the time many feared that some of the mineral particles contained in the tailings (alleged to be asbestos or asbestos-like) would cause human health problems. This Conference was thus convened to readdress the problem of the mineral content of the Biwabik Iron Formation and to whether any minerals contained in the ore could cause human disease. The four papers given in this session address the nature of the mineral particles in the taconite rock, the definition of the term ??asbestos?? and the history of the legal controversy over the possible health effects of certain mineral particles contained in the Biwabik iron range ores. Paper 1?Geology of the Biwabik Iron Formation and Duluth Complex Mark A. Jirsa, James D. Miller, Jr., G.B. Morey The Biwabik Iron Formation was a principal source of ore for the American steel industry during the 20th Century. The unaltered iron deposits, called taconite, contain approximately 30% iron and 50% SiO2. About 75% of the iron in taconite resides in the mineral magnetite, the remainder is largely in iron carbonate and several iron-silicate minerals.

Jan 1, 2007

By Geoffrey Berry

Exposure?response relationships between the relative risk of lung cancer and quantitative measures of exposure to asbestos are available from a number of epidemiological studies. Meta-analyses of these relationships have been published by Lash et al. (1997) [Lash, T.L., Crouch, E.A.C., Green, L.C., 1997. A meta-analysis of the relation between cumulative exposure to asbestos and relative risk of lung cancer. Occup. Environ. Med. 54, 254?263] and Hodgson and Darnton (2000) [Hodgson, J.T., Darnton, A., 2000. The quantitative risks of mesothelioma and lung cancer in relation to asbestos exposure. Ann. Occup. Hyg. 44, 565?601]. In this paper, the risks derived in these meta-analyses have been compared. Lash et al., concentrated on process and found that the risk of lung cancer increased as the asbestos is refined by processing. Hodgson and Darnton concentrated on fibre type and found that the risk was highest for exposure to amphibole asbestos (crocidolite and amosite), lowest for chrysotile and intermediate for mixed exposure. Some of the differences between the conclusions from the two meta-analyses are a consequence of the choice of studies included. The range of asbestos types included in the studies in the analysis of Hodgson and Darnton was wider than that in Lash et al., enabling differences between fibre types to be analyzed more readily. There are situations where occupational exposure to chrysotile asbestos has shown no detectable increase in risk of lung cancer. Taconite miners have shown no increased risk of mortality due to lung cancer. © 2007 Elsevier Inc. All rights reserved. Keywords: Mesothelioma; Amosite; Grunerite; Taconite; Crocidolite; Tremolite; Anthophyllite; Winchite; Risk assessment; Etiology

Jan 1, 2007

By Botelho Junior, Amilton Barbosa, Denise C. R. Espinosa, David B. Dreisinger

Copper and cobalt can be found on nickel laterite ores, and cobalt can be found also on copper ores, and many contaminants such as iron, aluminum, and magnesium are associated with these ores. In hydrometallurgical process, a purification step is necessary after leaching due to the presence of these impurities. Chelating resins are more selective for some metals than others, making them more efficient than cationic resins. This overview discusses chelating resin applications to recover copper, nickel, and cobalt from mining process and mining tailings and the effect of contaminants in leach solution. Chelating resins with iminodiacetate functional group can be used for selective copper recovery, and both iminodiacetate and bis-picolylamine resins are highly selective for nickel and cobalt. Chelating resins with the same functional group can have different performances on the kinetics of loading, because of variations of structure, the density of functional group, and degree of cross-linking. This article reviews commercial chelating resins that can be applied in leach solutions with different compositions, and also possible innovations for uses of chelating resins to recover metals from mining process and mining tailings.

By Brooke T. Mossman

Asbestos fibers are highly fibrous silicate fibers that are distinguished by having a large aspect (length to diameter) ratio and are crystallized in an asbestiform habit that causes them to separate into very thin fibers or fibrils. These fibers are distinct from nonasbestiform cleavage fragments and may appear as thick, short fibers which break along cleavage planes without the high strength and flexibility of asbestiform fibers. Since cleavage fragments of respirable dimensions have generally proven nonpathogenic in animal studies, little data exists on assessing well-characterized preparations of cleavage fragments in in vitro models. The available studies show that cleavage fragments are less bioreactive and cytotoxic than asbestiform fibers. © 2007 Elsevier Inc. All rights reserved. Keywords: Asbestiform; Cleavage; Fibers; Fibrous

Jan 1, 2007

By John F. Gamble

Paper 1?South African experience with asbestos-related environmental mesothelioma: Is fiber type important? Neil White, Gill Nelson, Jill Murray The purpose of this review was to illustrate the importance of the type of asbestos in environmental mesothelioma. South Africa is a logical place to assess fiber type. The three major types of asbestos (crocidolite, amosite and chrysotile) were mined (all asbestos mining stopped in 2002) in South Africa. The association between asbestos and mesothelioma was discovered in South Africa. The occupational literature indicates high mesotheliomagenic potential for crocidolite, less for amosite and less still for chrysotile. Since South Africa has been a major source of crocidolite, relatively high rates of mesothelioma in the mining population is not surprising. High rates of mesothelioma due to environmental exposure is surprising, except perhaps when the authors? point out potential sources for community exposures (e.g., mine tailings used for road surfacing, golf courses, brick and plaster making; insulation in residential ceilings; children playing on fiber-rich waste rock). The authors? reviewed four studies reporting on mesothelioma cases and their sources of exposure and fiber type. Overall 23% of the known cases were attributed to the environmental (not occupational) exposure and about 90% were due to crocidolite asbestos. The proportion of environmental mesothelioma is considerably higher than in Western Australia where crocidolite is also mined. There the overall rate of environmental mesothelioma is about 6% (and less than 1% from residence in a crocidolite mining area).

Jan 1, 2007