Search Documents

By Oaitse Medupe

The feed to the BCL concentrator is made of the ore from Phikwe No3 shaft, Selebi shaft and Selebi North shaft. The receiving bin of the concentrator has daily throughput of 7869mt live capacity of ore with feed grade from underground operation of 0.70%Ni, 0.75% Cu and 0.05% Co. The valuable minerals in the ore are Pentlandite, Chalcopyrite. Cobalt is present mainly in the solid solution in pentlandite. The common non-sulphides minerals are Amphibolites, quartz, micas, and Feldspar while pyrite and pyrrhotite are the major gangue sulphides. Pyrrhotite contains between 0.1% and 1% Ni in solid solution. From the mineralogical investigation, it was found that approximately 65% of the pentlandite in the ore occurs as exsolutions in the pyrrhotite and the grain sizes ranges from 8 to 38µm. about 25% of the nickel bearing pentlandite is medium grained and subhedral. This kind of pentlandite occurs along the cracks of pyrrhotite or as inclusions in pyrrhotite. The rest of pentlandite present is disseminated in the gangue matrix. Because of the fine occurrence of pentlandite, fine grinding was conducted in order to improve the recovery as well as the concentrate quality. A series of subsequent flotation test were performed in order to evaluate grinds of 35, 40, 45, 50, 60 and 80% passing 75µm. It was observed that ? The mass pull increased together with increasing fineness of grind ? Similar nickel recoveries were obtained at 35 and 40% passing 75µm but from 50% and 60% the grind was seen to adversely affect the nickel recovery. At 80% passing 75µm the recovery increased by small amount. ? Flotation kinetics showed higher initial nickel recoveries but these did not translate into higher final recoveries. ? Grinding finer than 80% passing 75µm yield very high grades of the concentrate in the first minute of the flotation test, and the grade is dramatically reduced in the fifth minute of the test. It was concluded that the current grind of approximately 48% passing 75µm is close to the optimum and no significant benefit were found to be associated with finer primary grinds. The inconsistence of the grade and recovery as well as the pentlandite losses will be discussed. Keywords: Pentlandite, Nickel losses, Grain size, Flotation

Jan 1, 2007

By G. T. C. Emere, E. C. Hunter

The use of cylindro-conical settlers for the clarification of underground water by E. C. HUNTER- (Associate) G. T. C. EMERE-, B.A. (Hons.) (Keele) (Visitor) This paper analyses the performance of conical settlers on Harmony Gold Mine from 1959 to the present time, and describes the investigation that was undertaken to substantiate and improve the use of conical settlers for a new pump chamber in another part of the mine.

Jan 5, 1977

By P. F. S. Jackson, A. Strasheim

In the survey "Analysis of South African raw bullion" the distribution of trace elements within the bullion have been shown to be distinctively dependent on the extraction process. In general the amalgamation process produces the more impure bullion with respect to trace elements. Some chemical and physical explanations are given for the differences that have been observed in the raw bullion as received at the Rand Refinery. The value of the spark source mass spectrographic technique in the study of the elemental impurities in bullion is demonstrated.

By M. D. G. Salamon

If a transition from one equilibrium state to another occurs during the course of mining, energy transfer takes place in the rock mass, which is assumed to be an elastic continuum. The energy components are defined as follows: the work done by external and body forces, W; the increase in stored energy in the mass, Uc; the strain energy in the rock mined during the transition, Urn; the work done on mine support or backfill, Ws; and the released energy, Wr. The energy balance is defined as (W + Urn) - (Uc + Ws) = Wr> 0, where the first set of components in parentheses represents the sources of energy, while that of the second corresponds to the known modes of energy expenditure and the component on the right is the unaccounted-for energy surplus, which must be released and dissipated in some form. The inequality Wr ~ Urn> 0 applies. Expressions for the energy components are derived first for the general case and then for the 'slit' modal used to simulate tabular excavations. Through specific examples, the importance of the progressive nature of mining is emphasized. The size of the steps used to enlarge the excavations appears to play a significant role in the mode of energy transfer. This observation forms the basis of the second paper in this series of two papers.

Jan 1, 1984

By K. Sinding

This paper discusses reasons for mining company mergers that have become the fashion, the role of the ?Juniors? and asks what the motives might really be. It examines changes in company concentration over the last 20 years in key mineral segments. Data at different stages of a project are examined to attempt to elucidate the role of the ?Juniors?. Areas for further research are suggested.

Jan 1, 2009

The possibility that type 430 stainless steel can become sensitized during annealing after hot-rolling was studied by simulated cycles of continuous-annealing heat treatments, and by calculation of the carbon solubility. It was found that the lower-carbon steel could be sensitized at lower annealing temperatures than the higher-carbon steel, which is in line with plant experience. The difference in sensitization behaviour is ascribed to the lower rate of recovery of the lower-carbon steel during cooling, since recovery is sensitive to the grain size. At practical heat-treatment temperatures, austenite formation does not play a role.

Jan 1, 1996

By P. R. Jamisch

The limitations of gold-mine evaluation by P. R. JANISCH, B.Sc. (Sur.) (Natal) (Visitor) Inherent uncertainty in the choice of parameter values places theoretical and practical limitations on the interpretation of a gold-mine valuation that are not necessarily removed by comparison of two valuations on the same assumptions. These limitations arise mainly in the estimates made of cost inflation and gold-price escalation, and lead to inconsistencies in the 'league table' method of investment analysis. The choice of discount rate is also critical in many cases. An approach to the overall problem that takes these limitations into account is suggested.

Jan 6, 1976

By R. C. Urquhart, W. P. Channon, D. D. Howat

Discussion: The mode of current transfer between electrode and slag in the submBerged-arc furnace by w. P. CHANNON, R. C. URQUHART, and D. D. HOWAT J. MEINTJES I have read the paper with much interest, and I should like to make a few observations. (I) The experimental work deals with resistance heating by an electrode immersed in a slag... AUTHORS' REPLY We thank Mr Meintjes for his critical analysis and helpful comments arising out of his study of our paper. Possibly we should emphasize at the outset that our experiments all related to the conditions in which the lower portion of the electrode was immersed in molten slag. We believe, however,

Jan 12, 1974

By F. H. Deist, J. P. E. Morris, E. Georgiadis

For some years the Collieries Research Laboratory of the Chamber of Mines of South Africa has been engaged in the development and application of computer programmes to aid in the solution of rock mechanics problems. It is the purpose of this paper to introduce some of the programmes having general applicability. A system capable of predicting stresses and displacements induced by large-scale tabular excavations is discussed. A finite element programme especially designed for handling layered continuum problems, and which is being used extensively has been supplemented by an automatic mesh generation facility that reduces problem preparation times considerably. Some typical applications of these programmes are described. An entirely new approach, potentially capable of performing linear three-dimensional continuum analysis at practical cost is introduced.

By M. J. Nicol

An electrochemical investigation of the dissolution of copper, nickel, and copper-nickel alloys in ammonium carbonate solutions by M. J. NICOL, Ph.D., B.Sc. (Hons.) (Wits.) (Visitor) The dissolution of copper and nickel in ammonium carbonate solution was studied by techniques involving electrohemical anodic dissolution and ring-disc electrodes. The rate of oxidation of both copper and nickel by copper (11) was shown to be controlled mainly by diffusion to the surface. Variations in rate with changes in copper (11) concentration, agitation, pH, ammonia concentration, temperature, and copper (I) concentration were investigated and rationalized in terms of their effects on the electrochemical half-reactions involved. Evidence was found for the passivation of nickel and nickel-copper alloys of more than 50 per cent nickel.

Jan 6, 1975

By A. J. Feltenstein

A theoretical model for prediction of dissolved gold loss from a rotary vacuum filter was developed as part of a program to implement optimizing control on gold plants The filter was modelled using a modification of the Hagen-Poiseuille equation and the Choudhury and Dahlstrom washing equation. The model has three parameters which must be determined from accumulated data before predictions can be made. These are the cake and cloth resistances and the filter washing efficiency. The model predicts with a fair degree of accuracy the response of the filter to changes in the independent variables and will therefore be a useful tool in the plant optimization study.

Jan 1, 1987

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By B. J. Pieters

The paper describes the difficulties experienced with inferior coking coals as Iscor began using larger blast furnaces for the production of liquid iron. Research conducted at Iscor from 1977 to 1979 showed that benefits could be gained from the use of partially briqueted charges, and it was decided to install briqueting plants at the Vanderbijlpark and Newcastle Works. Details are given of the later plant, which was supplied by a consortium consisting of Voest Alpine, Didier Engineering, and Sumitomo Metal Industries. Sumitomo also supplied information on the optimization of coke quality along the lines of their Sumicoal System. The results have been a marked improvement in coke quality, much better blast-furnace operation, and increased productivity.

Jan 1, 1991

By V. M. Lovell, N. P. Finkelstein

The concepts involved in flotation research are discussed and aims are presented. Three different methods of investigation can be used, all of which are applied at the National Institute for Metallurgy (N.I.M.), and these are the empirical, trial and error method, the chemical engineering method, and the physicochemical approaches. This paper is devoted to the last of these. Because of the complexity of the physicochemical interactions involved, the work has, to a large extent, been concentrated on only one aspect, viz. the interaction between the mineral surface and reagents in solution, which was considered of major importance in the understanding of the process. The aspects on which work has been done are the concentration of uranium, the reaction between salt minerals and fatty acids, mixed xanthate-cationic collector systems, and the reaction between sulphide minerals and thiol reagents. Selected problems from the first two of these are discussed in some detail and deal with the agglomeration flotation of uranium and the chemical control of the flotation process for phoscorite. A detailed discussion is also presented of the progress made in the understanding of the interaction between sulphide minerals and thiol reagents, which is of more general application. Finally, an indication is given of the future direction of physicochemical research at the N.I.M.

By M. D. G. Salamon

In view of an urgent need for a simple means of simulating the behaviour of stratified rock masses, a long-dormant linear model is revived, generalized, and discussed in some depth. The model is piecewise homogeneous, consisting of a pile of homogeneous isotropic laminae in which the interfaces between beds are parallel and free of shear stresses and cohesion. The continuity of stresses and normal displacements is assured across the bedding planes and, to maintain simplicity, the theory of thin plates is used as the kernel of the model. The paper covers the case where the rock mass consists of discrete beds in which the layers are arranged either heterogeneously or systematically. The stratification is regarded as uniform when all the layers are of the same thickness and their Young's modulus changes exponentially with depth; and as homogeneous when all the laminae have identical thickness and properties. The case of uniform stratification is also treated on the basis of an equivalent quasi-continuum derived from the basic model. Attention is focused on the derivation of influence functions. It is demonstrated that the quasi-continuous models, when they are available, can replace their distinct-layer counterparts. The homogeneous quasi-continuum, which permits the derivation of its influence functions in closed form, facilitates the determination of the roof and floor convergence. In the case of a significant class of problems, the convergence distribution is defined by a second-order differential equation in the xy plane, which simplifies to a Poisson's equation if the mining excavations are unsupported. With this result, the paper prepares for the solution of a host of practical problems. These solutions are presented in a series of papers that are in the course of publication.

Jan 1, 1991

By G. R. Addie, A. S. Roudnev

The Hydraulic Institute has completed the task of developing a new ANSI/HI standard 12.1-12.6 (2005) for rotodynamic (centrifugal) slurry pumps covering nomenclature, definitions, applications, and operation. The standard provides examples of the different slurry pump types and contains an extensive section on pump and slurry definitions. The effect of slurry on pump performance is covered along with the pumping of froth. Reference is also made to ANSI/HI standard 9.6.7 (2004), which contains anew method for pump performance correction when handling viscous fluids. Classification of slurry services is established and then is used to determine limitations on velocities and total head per pump in order to obtain acceptable wear performance. The new service class, head per stage and other limits are directly related to capital and other cost considerations that will affect solids transport system economics. The writers review the contents of the new standard, highlight the main points, and discuss the reason for the slurry classification, corresponding limits and expected implications, particularly with respect to operating costs of the pumps in solids transport systems.

Jan 1, 2007

By P. Horrell, K. Rhodes, G. Harrison, J. Dean, D. Sammons, M. Stander

Anglo Platinum have perceived a need to increase the rate of reef development both for new mechanised stoping technology and on conventional new developing mines. The Research and Development Division of Anglo Platinum therefore initiated an experimental reef raise project with a tunnel boring machine (TBM) at Bafokeng Rasimone Platinum Mine (BRPM). The scope of the trial was for the boring of a reef raise 340 metres in length on the Merensky Reef. The boring phase of the trial took place over six months and the average rate of penetration of the TBM was 0,47 metres/hour. TBM utilisation was 22%. The TBM used in the trial was a Jarva MK6 manufactured in 1972 and its design with its backup system was not considered to be an ideal machine for reef development. However it was the intention of the trial to prove the concept of developing with a TBM on reef. In this respect the trial was unequivocally a success. There were many problems and long delays did occur during the boring phase. Nevertheless there is every confidence that a new TBM can be designed specifically for this type of work that will achieve high rates of advance up to (say) 400metres/month and with a more flexible steering system in order to negotiate reef changes. It can therefore be expected that TBMs will be used in the future for reef development on South African platinum mines.

Sep 1, 2001

By A. H. Swart, M. F. Handley

Unplanned stope panel collapses occur on most near-surface and shallow mines in South Africa. Although these incidents often occur during blasting, they pose a major threat to the safety of underground workers and the economic extraction of orebodies. Most stope panel collapses occur due to excessive panel lengths that are not designed according to a systematic design procedure or methodology. Instead, panel lengths are often dictated by the equipment in use and by previous experience under similar conditions. Hence, a rock engineering design methodology for the design of stable stope panels between pillars is of vital importance for optimum safety and production in shallow mining operations. Using the proposed design methodology described in this paper, rock mechanics practitioners and mine planners should be able to identify and quantify the critical factors influencing the stability of stope panels. The critical factors should then be used as input to the design of stable stope panels that will provide the necessary safe environment for underground personnel working in stopes. The proposed design methodology is an iterative process, which includes aspects such as rock mass characterization, estimation of rock mass properties, identification of potential failure modes, consideration of appropriate stability analyses and other elements of the rock engineering design process. This process continues after implementation. During monitoring, new data should be included in the database and the design process repeated on a regular basis. Design approaches included in the proposed design methodology include empirical methods such as different rock mass classification methods, analytical methods such as elastic and Voussoir beam analyses, kinematic analyses, probabilistic analyses, and numerical analyses. Keywords: stability, stope panels, design methodology, hard rock mines, shallow mining operations

Jan 1, 2004

By G. L. Gomes-Sebastiao, W. W. de Graaf

"Gomes Sand is a quarry operation that produces sand and aggregate for the construction industry. The quarry is experiencing inconsistencies in the fragmentation and poor pit conditions as a result of poor drilling and blasting practices. This results in excessive downtime in the load and haul and crushing processes.A benchmarking exercise of the blasting practices was conducted to evaluate the effect of the inconsistency on the mining cycle. After changes in the blasting practices the downtime was reduced, which improved the crushing plant utilization by 4.9%. The improved blasting practices and more consistent fragmentation decreased the average number of loads lost each month due to jaw crusher blockages from 9.2% to 3.9% of plant throughput. The change in blasting practices also improved pit conditions. IntroductionGomes Sand is a quarry operation that has been in operation since 2009, producing sand and stone for the construction industry. The quarry was experiencing unacceptable blasting results. The repercussions included uneven pit floors, large amounts of oversize rock (>500 mm), and inconsistent fragmentation.The blast results affected the load and haul operations as well as the efficiency of the crusher. This resulted in downtime in the daily operations, and consequent production and revenue losses.The crusher product should have a top size of 50 mm. A blast fragmentation of <50 mm would improve the downstream operations and the crusher throughput.An investigation into the blasting practices was carried out to assess whether the downstream delays can be eliminated by improving the blast results. The exercise included:* Assessing if the designed blast layout is adhered to on the bench* Observing the quality and control of drilling* Observing the charging procedure of the blast-holes* Benchmarking the fragmentation consistency of the blasted rock using current blast design and practices* Analysing the throughput of the crushing plant* Investigating the power consumption of the crushing plant and determine if a change in blasting practices will affect this* Evaluating the hours spent by the hydraulic hammer on secondary breaking."

Jan 1, 2017

By J. H. Bulloch

This paper describes detailed fractographic analyses of several specimens that had undergone corrosion-fatigue tests at high stress ratios in simulated pressurized water-reactor environments. The distribution and morphology of non-metallic manganese sulphide inclusions are shown to strongly affect the growth of environmentally assisted cracks (EAC), and certain features suggest that a hydrogen-assisted mechanism is responsible for the observed EAC growth. The incidence of transient EAC growth in isolated regions suggests that the critical conditions that trigger this type of growth are the &apos;right&apos; local chemistry at the crack tips and imposed mechanical conditions.

Jan 1, 1987