Search Documents

By M. Sciarone, B. Collins

The production, properties, and selection of ferrosilicon powders for heavy-medium separation by B. COLLlNS. B.Sc Eng. (Rand) (Fellow). T. J. NAPIER-MUNN. B.Sc. (Eng.). A.R.S.M. (Visitor). And M. SCIARONE. M.Se. Eng. (Delft) (Visitor). There are basically two types of ferrosilicon powder available to operators of heavy-medium plants in South Africa spherical and milled grades. The production processes are described, and the properties of the two types are examined and compared. Guidelines are given for the selection of the correct grade of ferrosilicon for any particular application.

Jan 12, 1974

By I. Zh. Bunin, M. V. Ryazantseva, V. A. Chanturiya

The paper proposes a new method for selective calciferous separation. The effect was achieved through the application of the combination of high-power electromagnetic pulses (HPEMP) and a specific reagent regime of the flotation. The combined application of HPEMP with the special reagent regime allowed for the improvement of the scheelite floatability: the recovery of CaWO4 rises from 41.2 % (untreated sample) to 58.5 (sample treated at 103 pulses). In contrast, the floatability of calcite decreases significantly: the recovery of calcite drops from 74.7% (untreated sample) to 41.1 % (sample treated at 103 pulses). The conditions were found for the selective separation of the minerals with very close flotation properties. Keywords: Calcite, scheelite, flotation, high-power electromagnetic pulses, DRIFT, XPS

Jan 1, 2020

By Z. Halifa, P. G. Geyer

Tapping a blast furnace is necessary not only to deliver the product, but is also essential for the safety of the furnace and workers in the cast-house. This paper will highlight the practices at ArcelorMittal’s blast furnaces in the Vanderbijlpark Works, with specific focus on tap-hole design and monitoring as well as casting practice. Extension of the tap-hole life and hearth campaign will be illustrated with reference to the methods of maintenance of the tap-holes, troughs, runners, and cast-house equipment. The importance of proper cooling, good thermocouple installation, and temperature monitoring will be explained.

Jan 1, 2014

By J Cahill, M Lee

Leinster Nickel Operations, located in Western Australia, consists of an underground and three open pit mines in relatively adverse ground conditions. This paper reviews our ground control practices in the open pits, covering aspects of ground support, wall control and monitoring. These methods have been effective in allowing mining operations to continue beneath unstable slopes. In particular, the use of Groundprobe?s Slope Stability Radar has enabled the Harmony Open Pit to safely operate for months following indication of failure from traditional methods. This case study highlights the benefits of investing in appropriate slope stability monitoring systems.

Jan 1, 2006

By NIM REPORTS

Notices CONFRRENCE ON COMPUTRRS IN ENGINEERING The above Conference, which is being organized by the Electrical and Electronics Board of the Institution of Engineer!!, Australia, ill to be held in Sydney on 16th and 17th May, 1974. It is being planned in conjunction with the Sixth Australian Computer Conference and will be held during the week immediately preceding the latter. NIM REPORTS Report No. 1495 A method for the determination of ekmental sulphur on the surface of sulphide minerals. Report No. 1500 The chromatographic separation and determination of nobk metals in matte-leach residues. Report No. 1505 The production of the refractory aluminium saicates, with special refererence to South Africa. Report No. 1517 Computer-controlled flotation plants in Canada and Finland. Report No. 1526 Heat of solution as a control of aqueous-ammonia concentration. Report No. 1529 South African costs of equipment for the metallurgical industry (197).

Jan 9, 1973

By P. R. Beeley

Metal founding - a modern perspective The recent development of metal founding is reviewed in the context of basic requirements for the successful manufacture of cil;5ti,ngs.Progress has been related to the two interdependent fields of process technology and product characteristics. . After a brief review of the growth of the traditional industry. various features of the modern industry are discussed. Reference IS made to current trends in process technology and to the introduction of new techniques affecting production engineering, product quality. and the general nature of the industry. Metallurgical aspects of metal founding are considered, and modern techniques for the control of casting conditions are examined. These aspects are related to the structure and quality of cast metal and to the development of newer types of cast material and product.

Jan 9, 1976

Professor R. N. Pryor, AR.S.M., B.8c., C.Eng., F.I.C.E., F.I.Min.E., F.I.M.M., who died on 14th July, 1979, after a short illness, was President of the Institution of Mining and Metallurgy for the session 1978-1979. Weld pool metallurgy A high level of current interest in welding characteristics and behaviour and in the properties of welds was amply demonstrated by the large attendance at The Welding Institute's 1978 Conference on 'Trends in Steels and Consumables for Welding' and by the overwhelming number of papers offered for the International Conference on 'Arc Physics and Weld Pool Behaviour' in May 1979. Mine ventilation The First International Mine Ventilation Congress was held in September, 1975, in Johannesburg, South Africa, at the University of the Witwatersrand. It was organized by the Mine Ventilation Society of South Africa. Occupational accidents and diseases The IXth World Congress on the Prevention of Occupational Accidents and Diseases will be held in Amsterdam from 6th to 9th May, 1980. Rock mechanics The 21st U.S. Symposium on Rock Mechanics is to be held at Rolla, Missouri, from 27th to 30th May, 1980. Protection against noise An International Symposium on the Protection of Workers Against Noisewill be held in Dresden (German Democratic Republic) from 27th to 30th November, 1979. Management of mineral resources A joint meeting of the Institution of Mining and Metallurgy, the Society of Mining Engineers of AIME, and the Metallurgical Society of AIME is to be held in London from 27th to 30th May, 1980. INFACON 80 During 1970 various South African institutes and associations agreed to organize an international ferroalloys congress. It was recommended that this should be made a continuing forum, where ferroalloy people could meet and discuss matters of mutal interest.

Jan 1, 1979

By P. J. A. Beukes, C. C. La Grange

INTRODUCTION Some years ago the authors proposed a modified procedure1 for carrying out micum index determinations2. The modifications consisted of using a drum of 50 cm internal length, i.e. half the length of the standard micum drum (a modification also adopted by the B.S.J.3), and the use of a + 25 mm coke instead of + 60 mm coke for the test. The proposed modified test and formulae for converting results obtained from it to standard micum test results and vice versa were based on the results obtained during the investigation of about 200 test cokes made in ovens of the South African Steel Industrial Corporation Limited (Iscor), the Fuel Research Institute co-operating with the experiments. Extensive testing of cokes has since been done at the Fuel Research Institute using both the standard and the modified procedures. The numerous test results obtained during this trial period fully support and strengthen the confidence originally expressed by the authors in the modified testing procedure. The scope of the modified micum index determination has in the meantime been extended by applying the testing procedure also to test cokes made in the Institute's experimental coke ovens, and also in this case the modified procedure has proved its usefulness. A difficulty is that when comparing the characteristics of cokes made in the Institute's two experimental coke ovens with each other and with those of cokes made from similar blends in commercial coke ovens, for example those of Iscor, the index values obtained invariably do not check exactly due mainly to inherent differences between the different types of oven4. For instance, resistance to abrasion of a coke made in Iscor's ovens is always appreciably higher than that of a coke made from the same blend (and having a similar moisture content) in the experimental ovens. This makes direct comparisons and the prediction of quality to be expected from commercial products, based on experimental coke oven results, difficult. It may also be added that workers in Great Britain some years ago reported a similar experience5. In the authors' opinion the main reason for the discrepancy is the relatively low height of the experimental ovens resulting in a much lower static pressure on the charge during coking than that obtaining in a commercial oven. The difficulty was pointed out and briefly discussed in a publication4 which appeared at a time when the micum test for coke evaluation had only just been introduced at the Institute, so that only B.S. shatter and abrasion test results were available for discussion in the publication. Needless to say, the introduction of the micum test by no means solved nor even alleviated the problem. On numerous occasions during the past few years the Institute has had to conduct contract investigations in its experimental coke ovens on behalf of companies which invariably desired an indication of the quality of coke likely to be obtained from certain coals or blends when coked commercially, more particularly in Iscor's type of coke ovens. It was, therefore, essential to accumulate statistical data which would enabe the prediction to be readily made. Fortunately the compilation of comparative coke-quality index values for the three types of oven under consideration has become possible as a result of coking investigations conducted in co-operation with Iscor over a number of years. During this period Iscor, on numerous occasions, kindly made available to the Institute portions of coals and blends coked in the Corporation's coke ovens, thus enabling parallel coking tests to be carried out in the Institute's experimental ovens. In this way enough statistical data became available to establish relationships between coking results obtained in Iscor's ovens and results obtained on similar coal charges in the Institute's ovens. The most practical and acceptable method of overcoming the problems of finding a suitable and simple basis enabling direct comparison between the cokes of the different origins mentioned to be made, is the assignment of descriptive arbitrary quality ratings, as indicated below, to the cokes obtained, it being argued that the quality rating assigned to coke made from a given coal or blend in the different coke ovens under standardized conditions should be the same, irrespective of differences in the index values obtained when subjecting the cokes to the usual coke evaluation tests. The system, which should enable the sponsors of coking investigations in the Institute's experimental ovens to make their own interpretations of the results obtained, is explained below. ARBITRARY QUALITY CLASSIFICATION OF COKES The Ml0m index1 (percentage material smaller than 10 mm after the test) of a blast furnace coke is a measure of its tendency towards breeze formation during handling -a low value indicating a low tendency. This is generally of greater importance under ruling South African conditions, than the M'40 index1 (percentage material larger than 40 mm after the test), which can be regarded as a measure of resistance to shatter. In fact, if the M10m value of a coke as made in Iscor's ovens is higher than about 11, the tendency of the coke to form breeze during handling and in the blast furnace is relatively so high that hardly any notice need be taken of its M'40 value, even if this is comparatively high. For this reason, therefore, much more weight should normally be assigned to Ml0m indices in the quality evaluation of cokes made from South African coking coals and blends, as the coals

By k. Lebecki, S. Trzcionka

The prototype and test results of the instrument for quick determination of incombustible content in deposited dust as a protection against coal dust explosion propagation are presented. Presently existing methods do not permit to obtain quick information about incombustible content, needed for the proper protection of workings. As the operating principle for the e instrument the dependence of reflection of infrared radiation intensity on incombustible content in the sample is chosen. The construction is based on the modern electronics. The measurement will be done at the sampling site. The range of the instrument is 0-100% of incombustible, direct reading, autonomous supply, weight no more than 0.5 kg, and is intrinsically safe according to EN Standards. During the Conference the instrument will be commercialized.

Jan 1, 2003

n interesting situation arose last week when two Vaal River residents wrote to me (and a third telephoned) giving me details of how Sasol wanted to develop an open-cast coal mine on the south bank of the Vaal, just upstream of the Barrage. This is agricultural land and is across the river from Millionaire?s Row, where a number of wealthy people have built river-side mansions. The mine would be hidden by a 30 m-high (10 storeys) earth wall set 300 m back from the edge of the river. It could operate 24 hours a day.

Jan 1, 1996

By Z. Botha

Sheryl Sandberg, the COO of Facebook, published a book titled 'Lean In', where she invites women to sit at the table. In summary, to 'sit at the table' entails not only embracing opportunity, but to actively seek out opportunities in leadership positions. Sandberg points out that, unfortunately, apart from institutional obstacles, a woman's own perceived limitations have a negative impact on her leadership ambitions. To create an environment where diversity will flourish, where everyone has a seat at the table and everyone has a voice, safety must be established first. To establish safety within a diverse team, there is power in relationships and connections. This study will first and foremost review theories in literature as to why diversity and inclusion are so important and the value that diversity brings to our industry. The study also recommends a few focus areas for improving diversity and inclusion in the industry.

Sep 1, 2022

Mixed integer programming (MIP) has been used for optimizing production schedules of mines since the 1960s and is recognized a shaving significant potential for optimizing production scheduling problems for both surface and underground mining. The major problem in long-term production scheduling for underground orebodies generally relate to the large number of variables needed to formulate a MIP model, which makes it too complex to solve. As the number of variables in the model increase, solution times are known to increase at an exponential rate. In many instances the more extensive use of MIP models has been limited due to excessive solution times.

Jan 1, 2010

By F. T. Cawood, M. N. M. Cudjoe

The ability to conduct real-time material tracking in mines has been a long-standing challenge. Technological innovations such as radio frequency identification technology (RFID) have over the years contributed to the effective tracking of material flow and reporting of metal content. This paper outlines the laboratory procedures and results from testing the suitability of microdot technology as a viable technique for real-time material tracking in mining. The paper clarifies the reasons for conducting the test and presents the material safety data sheet (MSDS) from a South African and Canadian perspective. Microdots from three aerosol systems were immersed in water, heated to 100°C, and crushed into coarse and fine material. These tests were used to ascertain if the technology could withstand mining conditions. A strength, weakness, opportunity, and threat (SWOT) analysis was used to evaluate and compare microdot technology with RFID. It was shown that microdot technology has some potential to track ore parcels because data integrity was retained after exposure to post-blast mining conditions. However, more improvement is required to digitally detect microdots before the technology can be implemented at scale in the mining industry.

Apr 2, 2022

Book review Doyle, William S. Strip Mining of Coal; Environmental solutions. Park Ridge (New Jersey), 1976. 352 pp. $32. Surface mining of coal is still in its infancy in South Africa. The environmental repercussions following large-scale disturbance of the land surface, and the secondary effects of the disposal of waste products and effluents from mining, have not yet become apparent.

Jan 1, 1977

By D. D. Howat

In the field of high temperature smelting processes there have been two dramatic changes in the past twenty years. These are, first, the application of tonnage oxygen for direct injection for the refining of molten iron and other metals and to provide the means of enriching air used for the combustion of fuel. Second, the application of electric power for the generation of high temperatures in place of the combustion of fossil fuels. Of these two developments the application of tonnage oxygen for the refining of molten iron has virtually revolutionised the steel industry throughout the world. The magnitude of this development is exemplified by the fact that less than 5 per cent of the world's steel production in 1960 was made by this process or 16 million tons out of a total of 350 million tons of steel produced, while in 1970 over 40 per cent of the world steel production was made by this process, ie, 251 million tons out of 628 million tons total. In the same period the proportion of steel produced by the old-established open-hearth process has shrunk from 75 per cent to 38 per cent. In the whole history of the development of high temperature metallurgical smelting processes there has never been anything remotely approaching this. The other development, the application of electric power for the generation of high temperatures has not had the impact of the oxygen injection process but I believe that what we should call the electric smelting revolution in metallurgical processes has very far-reaching ramifications for steel production and other pyrometallurgical processes. This may seem a bold and brash statement but it must be remembered that the oxygen injection process constitutes a link in the chain critically dependent upon the production of vast tonnages of molten iron from very large modern blast furnaces. The Achilles heel of this chain of processes, upon which such a large percentage of the world's supply of steel depends, is the availability of metallurgical coke in turn dependent on natural resources of coking coal. Without any exception each industrial country in the world faces a shortage of resources of coking coal and in some cases a critical shortage. Certainly within the present century the major iron and steel producing countries of the world will face this critical shortage of coking coal and major modifications to steel making processes will become inevitable. W. F. Cartwright (Deputy Chairman of B.S.C) said recently that there are considerable doubts as to whether the world will be able to provide enough coking coal to meet world steel demands from the late 1970's onwards if the B.F.remains the main means for making iron from ore. This is one of the supreme ironies of the world metallurgical situation to-day when the technology of iron and steel production has reached an extremely high peak of technical efficiency. The newest modern iron blast furnace capable of producing 6 000 to 8 000 tons per day of molten iron represents probably the most efficient piece of high temperature metallurgical plant and operation known to man. The conversion of this molten iron into steel by the oxygen injection process has made available to the engineering industry steel of a quality and at a price which is quite remarkable. Yet this vast metallurgical pyramid rests on the completely insecure and uncertain foundation of inadequate world resources of coking coal. The shortage of reserves of coking coal in this country is acute and it is possible that these resources will be exhausted within the next twenty years. Yet unless some completely unexpected catastrophe occurs the demand for steel in this country will probably rise at a faster rate than in the Western world due to the expansion of the Bantu population and the increased standard of living. To offset the inevitable shortage of coking coal are our much greater resources of bituminous coal which although of low grade provide a suitable fuel for electric power generation. The geographical disposition of the coal fields in relation to the great industrial areas of the Transvaal makes it inevitable that the development of the pyrometallurgical industries must depend heavily on electric power. The position in this country with regard to electrical power generation and consumption is rather anomalous. Per capita consumption of electric power is high - in 1964 almost twice the world average of 870 KWH and twenty-five times the average of 34 KWH for the Continent of Africa. In 1964 fifty-four per cent of the total world electric power was used in industry - the ratio being approximately 1/9 mining to manufacturing uses. As shown in Table I in 1969 67.2 per cent of the total output of electric power from ESCOM was used for mining and other industrial uses but almost in the ratio 6/4 mining to industrial uses. These figures emphasise the enormous importance of the mining industry to the economy of this country and underline the major contribution made by the gold mining industry. What is of very significant importance is that although the mining industry remains by far the largest single consumer of electrical power the consumption of power for industrial uses is rising rapidly as shown in Table II.

"Chairman: Professor C. O. Frush Rapporteur: Mr A. C. SchmidtPapers:Planning of underground copper mining by J. K. Williams, L. Smith and M. P. WellsLinear programming models of copper leach and solvent extraction plants by W. P. C. Duyvesteyn, J. R. Cutland and J. R. L. RusselPlanning and forecasting stope production by D. W. Kappes and P. F. X. Moussett-JonesA proposed method of dynamic ore reserve assessment for a caving system of mining by A. F. Spinks and S. P. NicholsThe initial point made by Mr L. Smith in presenting his paper was that the planning aid outlined in the preprint was neither sophisticated nor complicated. However, it was a system which worked and was a very real way in which the computer was being used to assist miners, in particular, who at the present moment have very little experience in the use of computers.Mr Smith apologised for the fact that the editors of the paper had eliminated all reference to 'time'. This was very unfortunate because the essence of the system was that it saved time, which was one of the main points made in the paper.The operations being planned by this means cover the Rokana orebody which is a stratiform body mined by open stoping.The planner has to decide how much ore to mine from each base in each time period of his plan, that is, from three to four months hence to a year ahead. Normal procedure is for the planner to have discussions with the underground manager on some of the information he requires. The sort of information needed is (i) tramming limits for each face, (ii) extraction and grade factors, (iii) the present status of mining operations so that the planner knows where to start the new plan, and, (iv) details of any other mining consider¬ations that need to be incorporated in the plan.The objective at this point is to produce an initial plan for discussion purposes. All the information required comes from one sheet per stops and shows, inter alia, the stope identifier, the length along strike, the ore tonnage, the copper and cobalt grades and, finally, the extraction and grade factors.The program itself, among many other things, checks the data for validity, compatibility, completeness and credibility and prints error messages accordingly. Output from this system is in the form of a summary of production from each face, as well as giving the figures of ore reserve depletion. This summary indicates which slopes are to be mined in this time period, the original survey grades (copper and cobalt), the estimated production grades, how much is to be mined from each stope and the copper and cobalt production accordingly."

Jan 1, 2014

Palabora Mining Company is operating a copper block cave mine in the Limpopo Province of South Africa. The mine was developed in the late nineties with a target ore reserve of 220 million tonnes of carbonatite at 0.69% copper. At 30,000 tonnes per day the operation had an estimated life of mine of approximately 23 years. Cave induced open pit side wall failure occurred in late 2004 with 130 million tonnes of waste reporting to the bottom of the open pit. This failure resulted in potential sterilization and dilution of the ore reserve and subsequent reduction in life of mine. Physical and numerical modelling indicated potential losses of up to 30% of the original ore reserves. Cave Management tools based on throughput principles are utilized to manage the failed waste ingress and ensure an optimum life of mine. Extracting the maximum rate possible, as soon as draw points are commissioned, with the view of achieving the highest production in the short term, is any mining operation?s goal as more money is required sooner. This approach, of course, improves the cash flow but presents a risk in the cave propagation profile as overall draw control is compromised. At Palabora it is evident from a Mineral Resource Throughput Management (MRTM) point of view that maximum production in the short term is not the solution. If high production rates are achieved and the profile of the cave is not manage correctly, this results in failed waste reporting to draw points earlier with adverse effects on grade. This would effectively and significantly shorten Palabora?s Life of Mine. The applications of good MRTM principles are required to assist the value chain for sustained profitability. The process commenced with change management paving the way for a better understanding and a holistic view for all role players.

Jan 1, 2007

By N. G. Cook, N. C. Joughin, A. J. A. White

The rate of face advance in the gold mines is between 3 and 10 m a month, with a median value of about 5 m a month; it follows that faces are blasted less frequently than is planned. There are many advantages in the use of short holes for stoping to give face advances of from 0,7 to 0,8 m per blast. This has the potential for so increasing the frequency of blasting that monthly rates of face advance could be improved significantly. Cleaning with face scrapers is too slow to permit the maximum achievement of a complete clean, drill, and blast cycle for each shift. Short-hole blasting, combined with the use of mechanical conveyors for face cleaning, offers the possibility of completing two such cycles each day, yielding monthly rates of face advance of up to 35 m. Experiments aimed at developing safe, unitized explosive charges well-suited to produce reliable face advances of 0,7 to 0,8 m per blast under a wide range of gold-mining conditions have been notably successful. A novel method of assessing the effectiveness of a blast based on the percentage of holes that leave socket lengths of 5 cm or less was used. Unitized charges of 60 per cent Ammon gelignite, 600 mm long by 25 mm in diameter, appear to be near optimal. The explosive is de-sensitized to obviate detonation by chance mechanical impact, but requires only a 6D detonator for initiation; it has good water-resistance. Means have been developed for producing these cartridges automatically, but the necessary machines will have to be built specially and the cartridges are not yet available in large numbers. A second experiment by way of an extended pilot production trial using these cartridges in holes 0,9 m long is now under way. Preliminary results indicate that drilling and explosive efficiencies and productivity are well above average, even though face scraping is being used. Unitized charges of this type are likely to prove even more advantageous when mechanical face conveyors come into use.

Jan 1, 1975

By C. Pamukcu

In this paper, which is aimed to serve as a review article, first of all a breakdown of the earth?s total water reserves is given. The usage areas of water in the mining industry are mentioned and these uses are briefly outlined, together with the main pollution potential of each. According to this, most of the water (almost 80% of it) is utilized in processing. Later on, probable damages that the mining would give to groundwater as a result of acid mine drainage, heavy metal pollution, euthrophication and deoxygenation is described. Finally, the measures and controls that should be taken against water contamination in mines are presented.

Jan 1, 2008

By C. Pamukcu

In this paper, which is aimed to serve as a review article, first of all a breakdown of the earth?s total water reserves is given. The usage areas of water in the mining industry are mentioned and these uses are briefly outlined, together with the main pollution potential of each. According to this, most of the water (almost 80% of it) is utilized in processing. Later on, probable damages that the mining would give to groundwater as a result of acid mine drainage, heavy metal pollution, euthrophication and deoxygenation is described. Finally, the measures and controls that should be taken against water contamination in mines are presented.

Jan 1, 2008