Search Documents

By W. A. Gericke, B. Olmstead, I. Mc Dougall, C. F. R. Smith

A finite element model was generated of a Søderberg electrode in a ferromanganese smelter. In this model, the casing and fins were modelled explicitly, and temperature-dependent material properties were included. A two-stage analysis procedure was used, the first part being a coupled thermal-electrical analysis using an applied DC current. As the casing material was non-magnetic, the DC current was deemed sufficiently accurate for this initial analysis. The proximity effect was not considered. Thermal boundary conditions based on assumed temperature distributions in the furnace were applied. Calculated temperatures agreed well with measured values. The joule heat calculated in this step was applied as a load to a coupled thermalstress analysis. The model was applied to a comparative study of alternative materials for the casing and fins. A number of different combinations of materials for the casing and fins were evaluated in a comparative study. The position of the baking zone was used as the criterion for evaluating the potential of each material combination. Based on this analysis, some material combinations were discarded as being entirely unsuitable, whilst the two most suitable combinations will be tested experimentally in the furnace. The stress analysis was performed on the most suitable option. The practical advantage of this analysis was that a number of what-if scenarios could be evaluated and discarded prior to embarking on expensive experimental work, thus limiting the amount of experimental effort required. A mathematical model allows for the comparison of options under controlled conditions, where parameters of interest can be varied individually, with all other parameters remaining the same, a condition which is difficult to achieve in an operating furnace.

Jan 1, 2004

By V. Riihimäki, M. Luotamo

The Unit of Toxicological Risk Assessment of the Finnish Institute of Occupational Health (FIOH) is conducting a 'Health Risk Assessment for Metallic Chromium and Trivalent Chromium' under the sponsorship of the International Chromium Development Association (ICDA) and the International Stainless Steel Forum (ISSF). This risk assessment will be conducted in accordance with the current European Union legislation in force (Council Regulation 793/93/EEC, Commission Regulation 1488/94/EEC, Dir. 67/548/EEC), but also to meet the regulatory obligations as set out in the European Commission REACH legislation proposal (Consultation Document, the Registration, Evaluation, Authorisation and Restrictions of CHemicals). Further aims include outlining the criteria for the setting of occupational exposure limits for metallic chromium and trivalent chromium compounds. Human Health Risk Assessment according to the current legislation shall entail hazard identification of the toxic end points (acute toxicity, irritation/corrosivity, sensitisation, repeated dose toxicity, mutagenicity, carcinogenicity, reproductive toxicity) including, as appropriate, dose (concentration) - response assessment, and derivation of the N(L)OAELs (No (Lowest) Observed Adverse Effect Level) and/or DNELs (Derived No Effect Level). Exposure assessments for workers, consumers and humans exposed via the environment take into account all the known intended uses. Risk characterisation will compare the typical and/or reasonable worst case exposure estimates to the N(L)OAELs or DNELs to determine Margins of Safety (MOS) for all human populations by each exposure scenario and type of effect, followed by conclusions about the presence or absence of risk. Although all of the key elements of existing legislation remain in REACH, the principal change is that, the burden of proof will be transferred from the member state authorities to industry. The new proposed format of Chemical Safety Report (CSR) will include Risk Management Measures (RMM) as an essential part of the report in addition to the risk assessment. The RMM plays a role in the evaluation of further testing needs and advocating reasons for possible waiwer of requirements. The research programme started in March 2002 and will be completed within the time frame of two years.

Jan 1, 2004

By E. Wolmarans

Dowding, Reynard and Associates Mineral Projects (DRAMP) was approached by the ARM/Lion Ore JV during July 2006 to conduct a feasibility study and control budget estimate for a new greenfield project for their NKOMATI Nickel mine 45 km east of Machadadorp. The scope included the evaluation and review of previous studies as well as a techno-economic trade-off on four possible comminution circuits ranging from conventional crushing and ball milling to fully autogenous milling. The following document encapsulates the thought process, decisions and the references used in selecting the final comminution route for the new 375 ktpm MMZ concentrator. Apart from the pilot test work performed, design simulations from a number of sources, performance results from a recently commissioned 100 ktpm MMZ concentrator, together with an understanding of the geology and mineralogy of the orebody and possible variations in the characteristics of the orebody over the life of mine were assessed. The results from all the above-mentioned work indicated that it would be possible to treat the MMZ ore at the desired throughputs to the desired grind sizes in a fully autogenous grinding (ABC-type) circuit. Autogenous milling is generally considered to be one of the higher risk milling circuits. This is mainly due to the fact that the ore, which is utilized as the grinding media, could be variable in terms of hardness and mineralogy/geology. Nevertheless, it is a very popular route as the cost benefits, more specifically the operating cost, are normally very attractive. This is especially the case when large low grade orebodies are evaluated. In North/South America, autogenous and semi-autogenous grinding circuits have been successfully employed during the past 20 years on large scale low grade operations. Taking all the above factors into account, the DRA/Nkomati project team recommended an autogenous circuit with the option to add steel to both the primary and secondary mills (if required) for the new operation in order to create the opportunity for significant operating cost savings. One has to bear in mind that all the new design simulations and decisions are based on previous work and potential unknown variations within the orebody will never be fully understood until the pit is operational for some time.

Jan 1, 2009

By M. Tangstad, H. Brun, P. Calvert, A. G. Lindseth

In 1999, Eramet bought the ferromanganese plants in Porsgrunn and Sauda (Norway) and Marietta (USA). With an ownership in the Comilog mine, the plants will operate with a high amount of Comilog ore. The properties of Comilog ore are reviewed and compared to a number of industrial operations. Important ore properties are chemical and mineralogical analyses, CO reactivity and mechanical strength. The advantage of Comilog ore is its contribution to lower energy and coke consumption. However, special precautions must be taken regarding the amount of fines and water introduced in the furnace, as Comilog ore is more porous compared to other Mn ores.

Jan 1, 2004

By F. Crundwell, A. J. Lathwood

A number of base-metal operations would like to increase production to take advantage of the higher metals prices. In general, this higher production should not be achieved with major operating changes. In hydrometallurgical facilities, leaching and pressure leaching represents one area where upfront limitations may be a bottleneck to the capacity of the entire plant. An assessment of the capacity of the leaching tanks and autoclaves was performed using a predictive model within the AweSym flowsheet simulator. The model is described, and the results of the application of the model to a number of different leaching reactors are presented. It is argued that the leaching number, which relates the residence time, particle size and the leaching rate, is of prime importance. Finally it is shown that there are some unexpected catastrophic events in increasing production capacity without a thorough understanding of the leaching operation.

Jan 1, 2007

By Deon van Tonder, Bert Van Hege

Comparison of various technologies for uranium recovery from sulphuric acid leach solutions shows that Resin-in-Pulp (RIP) and/or Solvent extraction (SX) based processing routes are usually cost effective (11). A combined RIP-SX recovery-purification route and a CCD-SX recovery-purification route were investigated and optimised. The design basis used for the investigation was a production rate of 200 kg/h U3O8 over a solution concentration range of 40 to 1500 mg/L U3O8. The OPEX for the RIP-SX processing route was found to be sensitive to the variation in uranium concentration in the leach liquor. One of the main drivers for this trend is the leach acid concentration. Conversely, the CAPEX of the CCD-SX processing route was sensitive to the uranium concentration in the leach liquor. The leach acid concentration only affected the OPEX of the CCD-SX processing route modestly, as the bulk of the acid is recovered in a pre-leach circuit. Contrary to expectation, the effect of extractant loss assumptions on the overall processing route economics was found to be modest to insignificant. It should be noted that the CCD-SX processing route OPEX was more sensitive to extractant loss assumptions than the RIP-SX processing route OPEX. Economic optimum wash ratios were determined for the CCD-SX processing route and increased with leach concentration ? the increase in wash ratio was less than proportional. A 5-stage CCD configuration was found optimal over the concentration range investigated.

Jan 1, 2007

By M. Hakala, P. Tolppanen

A method to predict stress-induced failures around excavations based on the mapped geological and rock mechanical information is studied. Totally of 7 km of newly excavated tunnels are mapped in the Inmet’s Pyhäsalmi mine in Finland at depth between 1000 - 1440 m from which the results and conclusions from the firstly mapped 1.7 km of tunnels are reported. The main rock type at the site is very hard volcanite having uniaxial compressive strength of 230 MPa in median and GSI-value 72 - 80. The maximum in situ stress around the tunnels is 65 - 85 MPa. The prediction of observed stress failures was preceded by comparing elastic 3-D simulation results of tunnels with three statistical yield criteria. Read’s or Hoek & Brown’s yielding criteria are found the most relevant, though, the effect of anisotropy was found to be significant. The most important parameters having a correlation with stress failures are the tunnel orientation and the foliation of rock. Also, the rock type and its strength, tunnel shape and the geological anomalies have their effects. Further, a delay time on mapping was found to clearly diminishing of the most violent failures. Une méthode de prédiction des contraintes à la rupture autour d'excavation, établie sur la base de cartographie géologique et d'information sur la mécanique des roches, à été étudiée. Au total, 7 km d'un tunnel nouvellement percé à une profondeur de 1000 à 1400 m ont été cartographiés dans la mine de Inmet’s Pyhäsalmi en Finlande. La roche principale du site est une vulcanite dur ayant une résistance à la compression uniaxiale de 230 MPa (valeur moyenne) et une valeur GSI de 72 - 80. La contrainte in situ maximale autour du tunnel se situe entre 65 et 85 MPa. La prédiction des contraintes à la rupture observées a été évaluée en comparant les résultats d'une simulation 3D d'un tunnel avec trois critères de limite d'élasticité statistiques. Le critère de limite d'élasticité de Read ou de Hoek & Brown’s se trouvent être les plus important, même si les effets de l'anisotropie sont significatifs. Les paramètres les plus importants ayant une corrélation avec la rupture sont l'orientation du tunnel et la foliation de la roche. De plus, le type de roche et sa résistance à la compression, la forme du tunnel et les anomalies géologiques ont aussi leur importance. Finalement, un délai dans la cartographie résulte en une diminution nette des ruptures violentes. Basierend auf kartierten geologischen und felsmechanischen Informationen, wird eine Methode untersucht, um spannngsbedingtes Versagen um Ausbrüche herum vorherzusagen. Insgesamt werden 7 km neu ausgebrochenen Tunnels in einer Tiefe zwischen 1000 und 1400 m in der Inmet Pyhäsalmin Mine in Finnland kartiert. Das hauptsächlich vorkommende Gestein ist sehr hart und vulkanischen Ursprungs mit einer mittleren einachsialen Druckfestigkeit von 230 MPa (Medianwert) und einem GSI-Wert von 72-80. Die maximale In-situ-Spannung im Tunnel beträgt 65-85 MPa. Die Vorhersage von beobachteten Spannungsversagen werden weitergeführt indem man elastische 3-D-Simulationsergebnisse von Tunneln mit drei statistischen Fliesskriterien vergleicht. Read's oder Hoek's Fliesskriteria werden dabei als die relevantesten Kriterien angesehen, obwohl auch der Effekt der Anisotropie als wesentlich erachtet wird. Die wichtigsten Parameter für eine Korrelation von Spannungsversagen sind die Orientierung des Tunnels und die Schieferung der Gesteinsschichten. Desweiteren haben Gesteinsart, Tunnelprofil und geologische Anomalien ihren Einfluss. Ausserdem zeigt sich, dass eine Verzögerung bei der Kartierung die ausgeprägtesten Versagen deutlich verringern.

Jan 1, 2003

Dr R. E. Robinson, Pr. Eng., obtained a B.sc. (Chem. Eng.) cum laude from the University of the Witwatersrand in 1950 and a Ph.D. (Eng.) from the same University in 1953, where he was awarded the Haikes Memorial Medal for Industrial Chemistry. Professor G. G. Garrett was appointed Professor of Physical and :Fabrication Metallurgy in the Department of Metallurgy at the University of the Witwatersrand in June 1980, and in January 1984 he became Head of the Department. Mr P. A. van Wielligh, Pr. Eng., climbed the mining ladder in the hard way, starting as a Mine Surveyor in 1936 and working his way up as Chief Surveyor, Underground Manager, Mine Manager, and Consulting Engineer, to Executive Director, including the intermediate steps. Mr H. E. James, Pr. Eng., is a graduate in Chemical Engineering from the University of the Witwatersrand. Both his B.sc. degree (1961) and his M.sc. degree (1964) were obtained on bursaries, the former from Gold Fields of South Africa and the latter from the Atomic Energy Board. Mr G. Pienaar, Pr. Eng., obtained a B.Eng. (Met) in 1967 and an M.Eng. in 1973, both from the University of Pretoria. Dr A. K. Haines, Pr. Eng., obtained all his degrees from the University of Natal, finishing with a. Ph.D. in 1971. Mr B. C. Alberts, Pr. Eng., obtained his academic training at the University of Pretoria, where he was awarded B.sc. degrees in both agricultural engineering (1963) and mining engineering (1965). Mr H. C. van Zyl, Pr. Eng., holds B.sc. degrees in mining engineering (1968) and civil engineering (1972), both from the University of Pretoria.

Jan 1, 1984

By C. A. Rawlins

In an underground mine the ingress of heat can generally be attributed to two sources (Rock exposure and artificial mechanisms). The heat load relating rock exposure is subdivided into stoping [~40%] and haulages [~20%]. Rock is exposed to the ambient air and as a mine increases in depth the VRT (Virgin Rock Temperature) increases which leads to more heat ingress underground. To counter the heat ingress, especially in low-seam stoping areas of a deep level mine, air is, a) cooled artificially, b) the amount of rock exposed is reduced in the back areas of a stope by backfill applications, and c) ventilation air is used more efficiently. The heat reduction within a stope due to placed backfill could amount to ~50% for operations mining at a mean rock breaking depth of about 4500 mbc (metres below collar). Unfortunately, due to backfill transport methods, the physical fluid properties and application methods adopted, additional heat is induced into the air. The heat ingress due to backfill application could amount to as much as 25% of the overall in-stope heat load. This heat influx, seen as a negative aspect of backfill operations, is nevertheless overshadowed by the overall in-mine heat load reduction capability of about 20% attainable. The in-stope benefit [~50%] attainable from backfill operations could be increased with the incorporation of a heat exchange (cooling) methodology to offset the additional heat ingress into the surrounding air of a deep underground mine.

Jan 1, 2003

By J. L. van Niekerk, J. Gunaselvam

This study investigates the use of appropriate seating systems for the control of whole-body vibration exposure in vehicles used in the SA mining industry. Six suspension seats were tested with six test subjects to determine the most suitable seat for an articulated dump truck based on the EM1 requirement in ISO 7096 (2000) standards. Transmissibility functions were measured in the laboratory using the newly commissioned Dynamic Seat Testing Facility with two excitation levels of 1m/s2 and 2 m/s2 r.m.s. in the 0.5 - 30 Hz frequency range. SEAT values were calculated for two input spectrums, the EM1 input spectrum specified as in ISO 7096:2000 and measured road vibration data measured on a typical articulated dump truck. The averaged SEAT value calculations indicated that not one of the seats will qualify as an ISO 7096 (2000) suspension seat but that it is possible to select a seat that will significantly reduce the vibration the driver will be exposed to.

Jan 1, 2003

By C. M. Rule, A. K. Anyimadu, L. Knopjes

Ongoing development work on ultra-fine grinding for various applications at the Group?s concentrators has been conducted by Anglo Platinum over the last few years. Current potential applications for mainstream grinding and concentrate grinding are the subject of a group-wide research and development programme. The first 10 000-litre 2.6 MW IsaMill was jointly developed by Anglo Platinum, Xstrata Technology and Netszch for installation at the Western Limb Tailings Re-treatment project in Rustenburg, South Africa. The unit was commissioned in late 2003/early 2004, and has operated in an intermediate concentrate regrind application successfully since. This paper describes the operational performance to date, as compared with the original duty specifications and objectives. The first mainstream M10 000 IsaMill with a 3 MW drive will be operational in November2006 at the Potgietersrus Platinum (PPL) ?Platreef? Sandsloot Concentrator in South Africa?s Limpopo Province. Key Words: Western Limb Tailings Re-treatment Plant, IsaMilling, Platreef, Platinum, Palladium, PGMs, tailings.

Jan 1, 2006

By B Vorster

Falls of Ground is one of the highest causes of incidents, accidents and fatal injuries in our mines today. These falls of ground may occur as soon as the face is exposed after blasting or after machine cutting. The falls of ground can also occur after support has been installed. There are many reasons why these falls occur before and after supporting of the face. It is therefore important to support the exposed face as soon as possible to prevent the falls of ground. It is also very important to support the face with the correct support products and to support the face as designed and required by the mining engineers. The possible reasons for falls of ground, possible support methods and the products available will be discussed in this presentation. In typical conventional narrow vein stoping operations, the use of conventional temporary support components to offer some support to workers, whilst the permanent and generally more elaborate support system gets installed or constructed, still results in injuries to people. The author wishes to discuss the following items in this paper:- ? Introduction ? Basic face behaviour after exposure ? Controllable Parameters ? Mining Engineers support designs ? Primary and Secondary Support ? Products available for prevention of falls of ground

Jan 1, 2008

[Ferro Alloys Producers Association The South Africa Institute of Mining and Metallurgy www.saimm.co.za Mintek www.mintek.co.za Eskom www.eskom.co.za ]

Jan 1, 2004

Mineral sand beneficiation plants comprise a complex combination of electrostatic, magnetic and gravity based separation techniques. These are combined and replicated in ways that provide the most efficient and cost effective separation of the valuable components. On line instrumentation has been developed at the JKMRC (eg. conductor/non-conductor(CNC) ) to measure the properties of the dry plant process streams. This paper provides results from the recent development of a novel low cost mass flow meter and discusses their combined use with the CNC instrumentation for the control of dry separation circuits.

Jan 1, 2003

By G. L. Smith

As the Platinum mining industry expands in the Eastern Limb of the Bushveld Complex it is increasingly evident that a major constraint to development is a lack of appropriate infrastructure. Of critical concern are water resources and spatial development / infrastructure. This paper identifies the context for infrastructure development in the Eastern Limb and two solutions that have evolved in the areas of water supply and spatial development. INTRODUCTION In an economics context, infrastructure is considered to be the structural elements of an economy which allow for the production of goods and services, without themselves being part of the production process. Despite the lack of a specific definition, infrastructure has largely become understood as to comprise road and rail transport systems, public transport systems, airports, public educational facilities, water supply and water resources, wastewater management, solid waste treatment and disposal, electric power generation and transmission, telecommunications and hazardous waste management systems. Critically it is important to understand that infrastructure not only comprises these physical elements but also the operating procedures, management practices and developmental policies that facilitate the effective utilization and development of the infrastructure in response to societal demand.

Jan 1, 2008

By S. Ranganathan

Production of ferro-chromium in the submerged-arc furnace is highly energy-intensive. Several process rates have been attempted to reduce the specific energy consumption in the production of this alloy. An exhaustive understanding of the thermo-chemical features of the production process can be used to reduce the specific power consumption significantly. The knowledge can be used to reduce the energy drain through undesired reactions in the process can be minimised. Plant trials have shown that specific energy consumption up to 100kWh/tonne of hot metal can be obtained by adopting this strategy. The process requires modification in operation practice and does not require any capital investment unlike other processes adopted for reducing power consumption. The principle of thermo-chemistry involved in this process development and results of plant trials are discussed in detail.

Jan 1, 2007

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By M. Kuchta, A. Newman

LKAB’s Kiruna Mine, located above the Arctic Circle in northern Sweden, is the second-largest underground mine in the world today. The orebody is a world-class high-grade magnetite deposit, from which three raw ore products are extracted. We use mixed integer programming to determine a production schedule, i.e., which production blocks to mine, and when to start mining them, so as to minimize deviation from planned production quantities while adhering to the operational constraints of the mine. The resulting model contains thousands of binary variables and a commensurate number of constraints, precluding us from obtaining a schedule in a reasonable amount of time. We describe a method that builds on prior, related work, to expedite solution time. Keywords: underground mining, production planning, optimization, integer programming

Jan 1, 2003

By John M. L Lewis, Antoine F. Mulaba-Bafubiandi

In the irradiation of ore particles by microwave energy preferential absorption of this energy occurs in minerals having specific dielectric properties (Bradshaw, 1999). This leads to a selective heating of the various components of within the ore particle matrix. The result is a differential thermal expansion of such components and the resulting induced stresses become ideally concentrated at mineral grain boundaries (Kingman et al., 2000). Dependent upon the relative composition of absorbent, opaque and reflective components this may lead to enhancement of the inter-granular fracture of the ore particles in the initial comminution process (Fandrich et al., 1997). The potential is thus a greater proportion of free mineral grain within the fractured ore particle that may lead to improvement in subsequent mineral separation processes. As the composition of the ore dictates the result of such a treatment (Kingman et al., 2000) it is essential to evaluate the response of each ore sample on an individual basis. This paper reports on results obtained from two ore samples: the one being the zinc ore from the Black Mountain mine (South Africa) and the other a pre-concentrated sample of handpicked cobalt?copper mixed oxide ore from the Gecamines (DRC). The equipment and methods used to simulate the comminution of the samples and evaluate the level of the value liberation will be described along with the results obtained. Using King (1975), Kanellopoulous and Ball (1975), and Gungor and Atalay (1998), a comparison between the behaviour upon microwave irradiation of sulphide and mixed oxide ores leads to conclude that while the technique (i.e. microwave irradiation) is appropriate to the zinc sulphide ore, it does not seem to lead to exceptional results for the oxide.

Jan 1, 2005

By J Steyn

Block Cave mining is one method used to extract ore from underground diamond mines as well as other massive orebodies such as copper. This necessitates the excavation of many kilometers of tunnel within the ore body. The integrity of these excavations needs to be maintained over a number of years. Most Kimberlites and weak orebodies are extremely susceptible to degradation when exposed to moisture and the atmosphere. It is therefore essential that some form of weathering protection is applied as soon as possible after exposure. Conventional methods of weathering protection such as shotcrete do not easily fit in with the production schedule, hence the need for a more efficient system that could be applied immediately after exposure and serve as a temporary support or even as a permanent support medium. The main advantages of thin sprayed liners (TSL) compared to shotcrete are the ease of application, speed of application, early strength, much reduced transportation of material, less labour intensive and cost effectiveness. Several Thin Sprayed Liners suitable for various mining environments and geotechnical conditions are available and could be well suited as additional support the undercut level development in a block cave where this may be required. TSL offer a cost effective support solution as an alternative to shotcrete in areas where the building of a support structure is not a requirement.

Jan 1, 2008