Search Documents

By B. K. Cantrell, K. L. Rubow

"Quantifying exposure to diesel exhaust aerosol in an underground coal mine depends on the ability to measure this component of respirable mine aerosol separately from coal dust. Such measurement is complicated by the carbonaceous nature of both the diesel and coal dust particulate that make up the respirable aerosol. Hence, special sampling and analytical techniques must be used to distinguish between these two aerosol components.As part of a continuing study of diesel exhaust aerosol characteristics, the U.S. Bureau of Mines has applied size selective sampling together with gravimetric analysis to separate and measure respirable diesel exhaust and coal dust aerosol concentrations in diesel-equipped underground coal mines. This technique is based on the premise that the diesel portion of the aerosol is predominantly submicrometer and the mineral dust portion is mostly greater than 1 µm in size. In the study, chemical mass balance (CMB) modeling, based on the distribution of chemical elements in aerosol and aerosol source material samples, is used to referee the analysis of diesel exhaust and mineral dust aerosol concentrations from the size selective sampling results.Based on the results of the study, the Bureau, in cooperation with the University of Minnesota and the U.S. Mine Safety and Health Administration (MSHA), have developed a prototype personal diesel exhaust aerosol sampler for underground coal mines. The sampler has three stages: a preclassifier stage to select for respirable aerosol, an inertial impaction stage with an aerodynamic diameter(d) size cut at 0.8 µm to separate diesel aerosol from mineral dust and collect the mineral dust, and a final filtration stage to collect the diesel fraction of the sample. The sampler has been evaluated in both laboratory and field experiments conducted by the Bureau, MSHA, and the Generic Minerals Technology Center for Respirable Dust (GMTC-RD)."

Mar 1, 1992

By David Montgomery

The feasibility of building a calibrator for the DuPont D-100 audio dosimeter is discussed. The desired specifications are used as guidelines but the possibility of their relaxation is also considered. Commercially available equipment is surveyed and found to not satisfy the guidelines. Several alternate concepts are investigated, and recommendations for further work are presented.

Jan 1, 1974

By J. E. Hamak

This publication contains analyses and related source data for 165 natural gas samples from 21 States and 1 foreign country. Of the total samples, 155 were collected during calendar year 1988. The remainder were collected earlier, but releases granting permission to publish were not received until 1988. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1989

By F. E. Brantley

Optimum autoclaving conditions were determined for separation of iron and manganese values from pregnant leach liquor produced in extracting manganese from low-grade umber are. The umber was leached with a synthetic anolyte similar to a recycle solution, used in manganese electrolysis cell operations, that had been renewed with ferrous sulfate and sulfuric acid. The equipment used and results obtained are presented for the several conditions employed. The kinetics of the separation were studied. Rate equations were derived for the formation of solid ammonium-manganese sulfate, (NH4)2 Mn2 (S04)3.

Jan 1, 1968

By M. J. Beus, M. K. Larson, J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of overcoring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 1995

Publicize the valuable information resources covering research conducted by the U.S. Bureau of Mines (USBM) and other federal laboratories that may be of interest to USBM customers. Access to this information is important for promoting further research and in transferring the technology to the end user. USBM Information Resources The USBM serves as the Nation's premier agency for mining- and minerals-related research. In sharing the benefits of this research with American industry and the American people, the USBM supports information systems outlining this vast array of technical knowledge. The USBM is dedicated to making its technology readily available and will continue to expand its electronic communications capabilities. The following resources provide instant access to USBM information. U.S. Bureau of Mines Bulletin Board. The Bulletin Board is a free service accessed by computer modem. All that you need are a computer, a modem, and communications software. The telephone number for the Bulletin Board is 202-501-0373; for information on using the system call 202-501-0406. Use X-modem protocol set to 1200, 2400, or 9600 baud, 8 data bits, and 1 stop bit (8,N,1). The information on the system can be viewed or downloaded. This service includes the following: announcements on Bulletin Board and other USBM activities; mineral news, features, and press releases from the Bureau's Office of Public Information; a list of recent publications and articles by USBM authors; mineral commodity data and Mineral Industry Survey reports; USBM Technology News, concise factsheets announcing milestones in USBM research and technology; a current list of computer products available from the USBM and the National Technical Information Service (NTIS); and a listing of cooperative research opportunities with the USBM.

Jan 1, 1995

By R. A. Beall

Homogeneous zirconium-alloy ingots have been cast on a production basis by the consumable-electrode arc-melting process at the Northwest Electrodevelopment Experiment Station, Bureau of Mines, Albany, Oreg. This paper describes the various methods used to introduce alloying materials into the ingot and evaluates 1 each method by the degree of homogeneity of resulting ingots, as determined in tests on sections cut from the ingots. As many as 30 or more ingots, each 6 to 10 inches in diameter and weighing 300 to 500 pounds, were melted, using each method; and, as most of them subsequently were fabricated to strip 0.1 inch thick, the test results are considered to be representative of production practice. Ingot homogeneity has been considered more difficult to achieve in arc-melting practice than by methods where the molten metal is poured into molds and the addition can be stirred into the total mass of metal before casting. Owing to the unique requirements of consumable-electrode arc melting the addition can be made only to that part of the total mass of the ingot that is molten at one time. Observation of the flowlines in 500-pound ingots produced at Albany indicates that the molten pool has a maximum depth about equal to the ingot diameter. The weight of metal molten at one time is, therefore, not over 100 pounds. Characteristically, the arc-melting process is conducive to segregation, which can be overcome, at least partly, by adding the alloy constituents almost continuously during casting.

Jan 1, 1956

A significant amount of information regarding the crushed stone and sand and gravel industries in each State is available from State agencies and State trade associations. These organizations continuously monitor the State mineral industries and are therefore an important source of detailed information at the local level. This third edition of the directory was prepared to provide a listing of government agencies and trade associations that can assist the users interested in obtaining detailed listings of crushed stone and sand and gravel producers, in addition to the information published by the U.S. Bureau of Mines.

Jan 1, 1994

By Eric E. Cather

A mineral investigation by the U.S. Bureau of Mines revealed no mines or prospects and no past or present mining claims in the Agua Tibia Wilderness Study Area (WSA). The area is underlain mainly by weakly foliated gabbro similar to rock that has hosted gem- and lithium-bearing pegmatites in the Pala district about 6 mi to the south. However, no gem- or lithium-bearing pegmatites have been discovered in the WSA. Nearby quarries in the gabbro have yielded rock for facing and dimension stone. No sand, gravel, or energy (oil, gas, coal, or geothermal) resources were identified.

Jan 1, 1984

By B. D. Hanson

The U.S. Bureau of Mines has developed an interactive computer program which enables the user to identify the effect of cutting system changes on relative dust generation and forces for continuous miner drums. The program simultaneously evaluates machine and coal seam parameters, and those parameters which the user can control. One or more of these parameters may be changed to determine their individual or collective effect on relative dust generation and cutting forces. The program is written in the BASIC programming language. A complete program listing is included along with user instructions and sample outputs.

Jan 1, 1989

By Russell J. Foster

This Bureau of Mines review focuses on the extent to which technologically and economically feasible programs in substitution, improved processing practices, including recycling, and design can achieve conservation of cobalt, chromium, manganese, and platinum-group metals, and thus reduce U.S. vulnerability to interruptions of supply. In addition, supply-side options--domestic and foreign resources, ocean minerals, and stockpiles--are identified. The report consolidates four major studies on these strategic and critical minerals sponsored entirely or partially by the Bureau in the last few years. These studies have been updated with further information from the recent literature.

Jan 1, 1985

By David L. Moffatt

Considerable current interest is evident[l,2] in the use of transient electromagnetic methods for subsurface remote sensing. A transient method is discussed which uses a periodic video-type pulse containing a wide frequency range. A video pulse is used as an interrogating signal both for "target" identification and detection for relatively short depth (c 20 meters) applications in soil and soft rock media. If the medium is favorable, e.g., hard rock, greater depth applications appear to be feasible. The same procedures would be applicable for deep geological exploration but would require a substantial reduction in frequency and increase in target size. It should be noted that video pulse generators with 35 kv peak voltage and nanoseconds base widths are now within the state-of-the-art, thus significant power over broad spectral ranges is possible. In the design of a video pulse sounding system, 5 main problem areas can be identified; 1 ) selection of the pulse shape or spectral content of the video pulse, 2) design of a radiating structure which effectively couples such a pulse into the medium, 3) isolation of the radiating and receiving mechanisms, 4) realistically accounting for the dispersion and attentuation of the medium and the air-medium interface, and 5) interpretation or processing of the received signal waveform. Each of these problem areas will be discussed and illustrated with experimental and/or theoretical results. The Video Pulse Selection of the proper video pulse signal is dictated by 3 considerations, the maximum desired depth of penetration, the attenuation of the medium and the required resolution and size of the target. For a lossy medium, penetration and resolution are clearly at cross purposes and a compromise is necessary. The exact nature of the compromise is dictated by the application, but the spectrum of the video pulse should not contain any frequencies higher than the predicted cut-off, i.e., that frequency which is attenuated to the threshold level of the receiver. As a practical matter, it may be necessary to select 1 or 2 video pulses reasonably suited

Jan 1, 1973

By John R. Benham

In 1987, at the request of the Bureau of Land Management~ the U.S. Bureau of Mines studied 7,600 and 3,000 acres, respectively, of the Slocum Creek (OR-003-075) and Upper Leslie Gulch (OR-003-074) Wilderness Study Areas in order to evaluate their mineral resources. They are located in Malheur County, OR, about 25 mi northwest of Jordan Valley. Both areas have an occurrence of stone (welded tuff) covering about 3,000 acres which is suitable for construction purposes including road metal, ballast, and road fill. However, similiar deposits are more accessible and closer to markets.

Jan 1, 1988

By Eric Cather

A mineral investigation of prospects in the Sawtooth Mountains B Wilderness Study Area (WSA) by the U. S. Bureau of Mines in 1983 revealed none had mineral production, resources, or development potential. The area is underlain by tonalite and smaller amounts of schist, One developed prospect and one prospect pit are in the WSA. They are in schist similar to host rock which has yielded gold in nearby mining districts, Sand and gravel deposits in the WSA are large but too far from markets to be considered resources. No energy (oil, gas, coal, or geothemal) resources were identified in the USA.

Jan 1, 1984

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

By Carlton E. Brown

The purpose of this report is to present results of tests on the effectiveness of a spray of water mist, commonly called compressed-air water blast or water blast, in reducing the concentration of dust present in the air shortly after blasting and during mucking of the blasted material. Many observations have been male on the effectiveness of such ,sprays, but published quantitative information on comparative dust concentrations with and without their use, obtained by dust-sampling methods in use in this country, is rare if not absent. Tests conducted in South Africa about 19164/ and more recently in England5/, 6/ have shown that such sprays reduce the dust concentration to very low values within a fen minutes after blasting,

Jan 1, 1938

Enhance hydraulic fragmentation technology by developing alternative grout sealing methods. Traditional grout scaling methods rely on chemical adhesion and require large contact areas to restrict high-pressure fluids. Fluid injection into rock requires economical and effective seals. With economical and effective seals, rock is easily fractured in tension by high-pressure fluid injection (fig. 1). Approach An innovative grouting technique was developed and tested by the Bureau. Slowly hydrating expanding chemicals are placed within a borehole and around a section of high-pressure tubing. Testing was conducted using 9/16-inch-OD smooth-walled injection tubes in 1.5-inch-ID holes. Seal lengths weir less than 10 inches and curing times were less than 24 hours.

Jan 1, 1989

By C. W. Smith

The Bureau of Mines conducted laboratory beneficiation tests on four samples of waste. granite sludge to devise a method of recovering silicon carbide (SiC). Froth flotation using creosote as a collector in an alkaline circuit resulted in concentrates containing over 91 pct SiC from each of the samples. Recoveries ranged from 43.1 to 86.6 pct. Single-stage flotation of sample A using a column flotation cell produced a concentrate containing 92.0 pct SiC with a recovery of 71.4 pct. Flotation using petroleum sulfonate as a collector in an acid circuit resulted in a concentrate containing 95 pct SiC from one of the waste granite products with a recovery of 97.5 pct .?

Jan 1, 1987

By Theodore Christos

The Bureau of Mines sponsored an investigation of the thermal oxidative degradation characteristics of selected ingredients employed in the formulation and manufacture of conveyor belts. This work was done to supplement similar studies of samples from finished conveyor belts and thus provide basic data for correlation of the potential toxic behavior of a finished belt with that of the individual ingredients. This report covers the study of (1) basic polymers (styrene-butadiene, neoprene), (2) reinforcing fibers (Nylon 6,6, Dacron, viscose rayon), (3) flame-retardant plasticizers (tritolyl phosphate-isomeric mixture, tri-p-tolyl phosphate, tributyl phosphate, tris (dichloropropyl) phosphate), (4) plasticizers (diphenylphtha1ate, di-(2-ethylhexyl) sebacate), and (5) a vulcanization accelerator (2-mercaptobenzothiazole).

Jan 1, 1977

By Robert L. Chufo

The paper, "An Electromagnetic Roof and Rib Thickness Sensor" presented at The 12th WVU International Mining Electrotechnology Conference in 1992, presented the results of roof coal thickness measurements in underground mines and rib coal thickness measurements in highwall mines. The microwave sensor described uses a unique spatial modulation scheme created by antenna motion, along with frequency domain signal processing, to solve the problem of media, target, and antenna dispersion. This paper further describes the advantages of the unique frequency domain signal processing technology chosen by the U.S. Bureau of Mines in extending previously reported one-dimensional thickness measurement technology to the generation of a full three-dimensional underground image of the underground environment. The electromagnetic signature of a media, whether it is coal or other geological material, is its permeability and permittivity and the effect on the velocity and amplitude of an electromagnetic wave as it passes through. High-quality imaging cannot occur without the identification of, and correction for, the permittivity and permeability of each layer of a multilayer geological deposit. Clutter, or any signal that can interfere with target discrimination, usually comes from objects in the field of view for which there is no design control. These are nuisance targets with possibly very high contrasts compared to the real target. The only proven tool to reduce clutter is to increase spatial, spectral, and polarization diversity. This paper will describe some techniques being used by the U.S. Bureau of Mines to increase the information content of both single-dimensional and three-dimensional imaging systems through the identification of media distortion mechanisms made possible by the use of spatial/spectral sensor technology. These techniques will permit high quality imaging in an environment where the data is corrupted by dispersion and clutter.