Search Documents

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

By Michael J. Sapko, Samuel P. Harteis, Eric S. Weiss

The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) recently conducted full-scale explosion experiments; these experiments evaluated the strength characteristics of various seal designs used for safely isolating worked-out areas in underground coal mines. Large-scale explosion tests were conducted within the multiple entry section of PRL’s Lake Lynn Experimental Mine (LLEM) employing the only currently accepted test method endorsed by the Mine Safety and Health Administration (MSHA) for seal design in American mines. These explosion tests are labor-intensive, expensive to conduct, and can interfere with other critical underground safety and health research programs conducted by NIOSH. Therefore, the PRL has developed an alternative seal evaluation method, based on a hydrostatic pressure loading concept, that can facilitate the in-situ testing of seals in an operating mine. Two chambers within LLEM and one within the Safety Research Coal Mine (SRCM) were used for hydrostatic pressure loading various seal designs. The results from tests in these chambers compare favorably with those from the large-scale explosion tests in the multiple entries. Preliminary size-scaling relationships for predicting the strength of standard seal designs as a function of entry size is also presented. In addition to testing seal designs at the required 20 psi static pressure level, the new facilities also allow for the determination of the seal’s ultimate failure pressure. This new approach shows promise as an alternative evaluation method for improving mine sealing technologies which, in turn, will enhance the safety of the underground personnel.

Four catalytic converters for diesel exhaust systems were tested to determine their effectiveness in reducing the amount of harmful substances discharged into the air. Tests were conducted with four different catalytic converter designs, using two diesel engines as exhaust gas generators. (Of the four noble metal catalytic converters, three are commercially available.) Testing showed that the catalysts varied widely in oxidation efficiency at light to intermediate engine loads, but that all were very effective in reducing emissions of CO, HC, aldehydes, and odor intensity at heavy loads (engine operating modes resulting in high exhaust temperatures). Particulate loading, particulate size, and NOx emissions were generally unaffected by any of the catalysts. The catalysts had one ad-verse effect on exhaust quality--increased sulfate emissions. Because of the potential problem of sulfate emissions, the exclusive use of catalytic reactors for emissions reduction does not appear to be satisfactory. However, when used with a means for subsequent removal of sulfates, a catalyst can function as a key component in an emissions control system for diesel engines operated in underground mines.

Jan 1, 1978

By William J. Campbell

The purpose of this investigation by the Federal Bureau of Mines was to design and construct a fluorescent X-ray spectrograph for dynamic rate studies of selective oxidation in molten metals and to establish basic principles for interpretation of data obtained by this method. An X-ray spectrograph was constructed in which the sample holder is a resistance wound furnace; it was operated up to 800° C. in oxidizing atmospheres. No difficulties were experienced with the cooling or heating systems nor with the protective layer of mica around the X-ray tube window, even though the oxidizing surface of the metal is only 0.5 inch from the X-ray tube window, Means are provided for heating under controlled atmospheres for selected time? temperature cycles.

Jan 1, 1961

By Philip W. Holland

The Bureau of Mines has developed a trace helium analyzer for deter-mining helium-4 in the parts-per-billion range. The instrument is used for analyzing pure gases, laboratory-prepared standards, and atmospher-ic samples. Accuracy at the 95-pct confidence level in the 50-to 20,000-ppb range is within ±2 ppb or ±0.4 pct, whichever is greater. The minimum detectable helium-4 concentration is calculated to be 5 ppb. The analyzer consists of a modified helium leak-detector mass spec-trometer, a laboratory-built sample inlet system, and a liquid-nitrogen-cooled charcoal trap. A programmable integrator and event-control module make automatic operation possible. The portability of the analyzer allows it to be used in the field.

Jan 1, 1984

By F. B. Tough

"INTRODUCTION Organizations formed for the purpose of conducting conservation work in oil fields, in order to conserve and prolong the supply of crude petroleum are rare and novel. Such an organization is the Rocky Mountain Petroleum Association, Denver, Colo, As our production of petroleum can no longer keep with the consumption, the plan of organization, character of work, and results obtained by this association are well worth considering. It is hoped that the results achieved in the Wyoming fields will serve to stimulate similar organizations among operators in the state or other oil fields of the United States, The Rocky Mountain Petroleum Association, Danvers Colo., was formed in May, 1919. It comprises the Midwest Refining Co,. The Ohio Oil Co., and the Continental Oil Co. These three companies entered into a cooperative agree¬ment with the Federal Bureau of Mines whereby $30,000 would be spent under the direction of the bureau, which agreed to furnish competent men, and to furnish the work and expenditure of funds. Although the financial burden for the first year's work, now drawing o a close, was carried by only three companies, they stipulated their desire that the benefit of the work should accrue to the industry, and that the personnel employed should be as zealous to assist one operator as another, without regard to whether ha was contributing to the support of the work or not."

Apr 1, 1920

By Henry G. Dorsett

Dust explosion data obtained in laboratory tests by the Bureau of Mines are presented for 73 chemical compounds and mixtures, 29 drugs, 27 dyes, and 46 pesticides. Information is given on ignition temperatures of cloud and layer, minimum igniting energy, minimum explosive concentration, percent of inert dust required to prevent flame propagation, limiting oxygen concentration in the atmosphere to prevent ignition, and pressures and rates of pressure rise at dust concentrations of 0.1, 0.2, 0.5, 1.0, and 2.0 ounces per cubic foot. Explosibility indexes are computed where data are available to permit comparison of the relative explosion hazard. Variations of explosibility parameters with chemical composition are discussed. General means for minimizing the dust explosion hazard are reviewed.

Jan 1, 1968

By C. K. Man

Coal dust explosions are routinely conducted within the full-scale experimental mine at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM) to meet the needs of numerous safety and health research programs. Many of these explosion tests over the years involved igniting different coal dust and limestone rock dust mixtures (up to 80% by volume rock dust). Following four more recent tests, floor dust samples have been collected and analyzed using the alcohol coking test and scanning electron microscopy (SEM) and the results compared to estimate the flame travel.

Jan 1, 2009

By Clark R. Neuharth

To assess the supply status of ultra-high-purity silicon for national defense needs, the U.S. Bureau of Mines conducted a general study of the availability of materials and processing technology for silicon used in the manufacture of infrared (IR) detectors from raw materials to the highly advanced device state. The United States possesses all of the raw materials and processing technology for IR detector-grade silicon production, but does not produce at all of the processing stages on a regular basis. Consequently, the United States continues to rely on foreign sources for some of these critical materials.

Jan 1, 1989

By J. Roger Loebenstein

Demand for arsenic exceeded supply, and major domestic and foreign producers allocated available supplies to customers for the fourth consecutive year. Major demand for arsenic was about evenly divided between industrial chemicals and agricultural chemicals. Legislation and Government Programs.-Effective April 1, 1981, taxes were collected from companies producing and importing 42 chemicals and petroleum products designated as hazardous, The revenue was used to begin funding of the 5-year, $1.6 billion "superfund" being established under Public Law 96-510, the Comprehensive Environmental Response, Compensation, and Liability Act, designed to help clean up spills of hazardous substances throughout the United States. As hazardous chemicals, arsenic metal and arsenic trioxide were taxed at the rate of $4.45 and $3.41 per short ton, respectively.

Jan 1, 1982

By Mary H. Brown

The heats of formation of oxalic acid and sodium, potassium oxalates, and lithium oxalates were related by solution calorimetry to the heat of formation of (COOH)2.2H20, a value believed to be reliable as reported in the literature. The following heats of formation were determined: (COOH)2(a), -198.1±0.1; (COOH)2(ß), -197.8±0.1; UAW,, -328.7±0.4; Na2C204 -316.2±0.1; K2C204, -321.9±0.2; and K2C204-H20, -393.5±0.2 kcal/mole. The heat of the crystalline transformation (COOH)2(a) ? (COOH)2(ß) was determined to be 0.30±0.02 kcal/mole at 298.15° K.

Jan 1, 1970

By P. D. Bergman

The high price of pollucite ore, its limited availability, and the need to provide stack removal of S02 present formidable obstacles to the use of pure cesium as a seeding material in MHD power generation. Cost estimates indicate that mixed potassium-cesium seeding is preferable to the use of either pure cesium or pure potassium. Cheaper electricity and higher open-cycle MHD operating efficiencies result from the use of mixed seed. Savings of $3,000,000 per year in power costs for a 1,000-MWE open-cycle MHD power-plant are envisioned if the mixed seeding technique is adopted.

Jan 1, 1972

By James S. Browning

The Bureau of Mines conducted laboratory and small-scale continuous tests of kyanite ore from Georgia to determine the technical feasibility of recovering commercial-grade kyanite concentrates by flotation. The research indicated that combinations of sulfuric acid and petroleum sulfonate may be used effectively for flotation of kyanite from quartzite-kyanite ore. Over 87 percent of the kyanite was recovered in a concentrate analyzing 55.8 percent A1203 and 5.3 percent acid-soluble Fe203. Subsequent treatment of the flotation concentrate by high-intensity wet magnetic separation reduced the acid-soluble Fe203 to 0.8 percent and increased the alumina content to 57.6 percent, with a recovery of 82.7 percent of the total alumina in the ore.

Jan 1, 1970

By Jami M. Girard, Ed Mchugh

Slope stability accidents are one of the leading causes of fatalities at U.S. surface mining operations. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is currently conducting research to reduce the fatalities associated with slope failures. The purpose of this paper to discuss some of this research and to present potential new technologies for slope monitoring and design. The paper also briefly discusses various warning signs of slope instability, introduces the most common slope monitoring methods, describes the limitations of various slope monitoring systems, and presents some field results using some of this new technology.

By R. L. Grayson, W. E. Wallace, M. D. Attfield, A. Q. Wearden, P. Bolsaitis, R. D. Kennedy, M. J. Keane, J. C. Harrison

"Respirable high-silica particles from four coal mines. a clay mine and a tunnelling site were analysed for silicon vs aluminum composition by performing scanning electron microscopy-energy dispersive X-ray analysis (SEM-EDS) at electron accelerating voltages of 20 kiloelectron volts (keV). The same particles were analysed at 5 keV to determine possible differences in surface vs bulk composition. In some cases high-silica particles exhibited a decrease in the ratio of silicon to aluminium K-alpha line intensities with decreasing electron beam accelerating voltage. This behaviour is consistent with aluminosilicate surface contamination or occlusion of a silica particle. Some 20 high-silica particles were analysed from each of 10 samples. Powdered aluminosilicate glass was used as a control for the behaviour of silica with a homogeneous distribution of aluminium in the particle. Significant differences were found between the control and sample means for an Illinois bituminous coal mine dust, two western and one central Pennsylvania bituminous coal mine dust low-temperature ashes. and a clay mine and mill dust sample, but not for an anthracite coal mine dust and two central Pennsylvania bituminous coal mine dust low-temperature ashes. INTRODUCTIONRESPIRABLE dust quartz content commonly is measured on bulk samples by using i.r. spectroscopy or X-ray diffraction. For research purposes, individual particle-by particle SEM-EDS analysis at 20-30 keV electron beam accelerating potential may be used also. Such measurements have not provided an unambiguous association of quartz content with occupational pulmonary disease prevalence in exposed workers (WALTON et al., 1977). Rather, there is evidence that coal rank modifies the relationship between dust exposure and pneumoconiosis development (WAL TON et al., 1977; ROBOCK and BAUER, 1990; ATTFIELD and MORRING, in press). SEM-EDS analysis was performed to measure the silicon fraction, Si/(Si +Ai), at 20 and at 5 keV on high-silica particles to determine if some respirable quartz particles generated by mining exhibit heterogenous composition with depth (WALLACE et al., 1990), which might affect the bioavailability of the quartz surface."

Dec 1, 1995

Locating subsurface conductive solutions is important for many applications, including in situ mining and environmental protection. Drilling boreholes for sampling is expensive and can increase contamination by mixing water from different aquifers. Various noninvasive geophysical methods are available, but previous comparisons were hampered by different methods being used at different sites or at different times. The U.S. Bureau of Mines (USBM) compared methods at one site using the same conductive solution to improve the reliability of the comparisons. Locating deep (> 100 m) solutions is most difficult, SO the USBM selected methods applicable for such depths. Objective Improve the ability to locate subsurface conductive solutions by evaluating and comparing applicable geophysical methods. Approach The experiment was performed cooperatively with other agencies to increase the number of methods studied. The USBM, the University of Arizona, Sandia National Laboratories, and Zonge Engineering and Research, Inc., conducted cooperative field tests of six electromagnetic (EM) geophysical methods to compare their effectiveness in detecting salt water brine of conductivity 3.6 S/m collecting at the water table, 157 m subsurface. The brine was injected through two boreholes. The test site was the University's San Xavier experimental mine near Tucson, AZ. Geophysical surveys using surface and surface-borehole, time-domain electromagnetics (TEM); surface controlled-source audiofrequency magnetotellurics (CSAMT); surface magnetic field ellipticity, surface-borehole, frequency-domain electromagnetics (FEM); and crosshole FEM were conducted before and during brine injection. A total of 110,000 I. of brine was injected over one week, but the effective target volume of brine was much smaller because of mixing with ground water and dispersion.

Jan 1, 1994

By E. D. Gardner

"It has only been in recent years that the proper ventilation of metal mires has received serious consideration. Increasing temperature and humidity with greater depth in some of the larger mines of the West prevented the efficient operation of the mines and made the installation of mechanical ventilation systems necessary. Doors that interfere with tramming are generally needed to control properly the mechanically induced air currents and are one of the inherent disadvantages of the system. In fact the necessity for the use of doors in the main haulageways has discouraged the installation of mechanical ventilation in some metal mines.A number of mining companies in Arizona are using ventilation doors which can be opened and shut mechanically by the motorman without leaving his seat or stopping his train, end thus interfere very little with the transportation of the ore. The Copper Queen Branch of the Phelps-Dodge Corporation at Bisbee introduced these ventilation doors and adapted them from those in use in the company's coal mine at Dawson, New Mexico. Other mining companies have installed the same type of door and it is now being used in a number of districts in Arizona.The doors at the Calumet and Arizona mine in the Bisbee district are representative of those in use. The doors at this mine are substantially built of 2-inch lumber, are air tight, are well placed and have two openings or passageways. The main door, which is used for the motor trains, is 5 feet wide by 6 feet high and is opened by compressed air and closed by a counterweight. At the side of the motor door is the man door, which is 16 inches wide by 5 feet high and is opened and closed by hand."

Aug 1, 1921

By S. R. B. Cooke, J. Bruce Clemmer, Will H. Cognill, F. D. DeVaney

"INTRODUCTION The domestic production of potash has made rapid strides in the past 4 years. In 1929 the United States produced 109,820 tons of potash-bearing material, equivalent to 61,590 tons of pure potash (K20). In 1933 to this had increased to 331,110 tons, containing 143,378 tons of potash, due chiefly to the development of the potash deposits near Carlsbad, N. Mex. The potash ores of that district occur at a depth of about 1,000 feet and as mined consist of a mixture known as sylvinite containing about 40 parts of sylvite (KC1) and 60 parts of halite (NaCl). By careful mining the extraneous material does not amount to more than 2 or 3 per cent. Such ore was used in the experimental work here reported.The usual chemical method for the recovery of potash from sylvinite, while efficient in the production of pure potassium chloride, requires,expensive equipment and is costly to operate. It occurred to the Bureau of Mines that ore-dressing methods, which have been applied to other nonmetallic minerals, might be adapted for the production of a grade of potash suitable for the fertilizer industry. After preliminary study by the Bureau of Mines showed that ore-dressing treatment was possible the investigation was extended under a cooperative agreement between the U.S. Bureau of Mines, the Potash Company of America, and the Missouri School of Mines and Metallurgy, Rolla, Mo.ACKNOWLEDGMENTSAcknowledgment is here given for valuable assistance in the laboratory of R. G. O'Meara, assistant metallurgist. U.S. Bureau of Mines, Tuscaloosa, Ala. who was on detail at the Rolla station during the early work; by E. W. Gieseke and Albert Ollar, temporarily employed by the Potash Company of America; and to N. H. Lenz, an engineer temporarily assigned to the station."

Feb 1, 1935

By Peter Kovalchikb, Gregory Colec, Syd Peng, R. J. Matetic, Jeffrey Petersond

Mine Safety and Health Administration (MSHA) data indicates that the roof bolting machine is third among all equipment and second among equipment in underground coal mining whose operators exceed the MSHA-PEL (Mine Safety and Health Administration-Permissible Exposure Limit). In response to this, the National Institute for Occupational Safety and Health (NIOSH) has conducted a study to reduce overexposures of noise to operators of roof bolting machines. An important segment of the research is to determine, characterize and measure sound power levels radiated by a roof bolting machine during different drilling configurations. The determined sound power levels generated during the drilling cycle are of major interest because the levels represent the overall sound power generated by the machine. These sound power levels, determined from laboratory tests, can be used to accurately assess the effectiveness of proposed controls for reducing noise exposure to roof bolting machine operators. By using the sound power level results obtained from the laboratory and a commercially available acoustical modeling package, a method for predicting sound pressure levels to roof bolting machine operators for differing drilling types and parameters could be determined. This paper provides a method for predicting sound pressure levels at the operator’s position of a roof bolting machine in an underground coal mine using sound power levels determined in the laboratory. To determine validity, underground coal mine data was also collected to compare predicted and measured sound pressure levels. The results of the predicted sound pressure level data were the same as the underground measured results. This research will provide the mining industry with a valid method for predicting a roof bolting machine operator’s noise dosage underground given any type of drilling configuration or drilling method utilized from laboratory testing.